Nanomolar detection of hydrogen peroxide at a new polynuclear cluster of tin pentacyanonitrosylferrate nanoparticle-modified carbon ceramic electrode

This work describes a new electrochemical sensor for hydrogen peroxide based on tin pentacyanonitrosylferrate (SnPCNF)-modified carbon ceramic electrode (CCE). The modified electrode was constructed by using a sol-gel technique involving two steps: construction of CCE containing metallic tin (Sn) powder and then electrochemical creation of SnPCNF film on the surface of CCE. The modified electrode was characterized by energy-dispersive X-ray, Fourier transform infrared, scanning electron microscopy, and cyclic voltammetry (CV) techniques. The charge transfer coefficient (α) and charge transfer rate constant (k_s) for the modifying film were calculated. The electrocatalytic activity of the modified electrode toward the reduction of hydrogen peroxide was studied by CV and chronoamperometry. A linear calibration curve was obtained over the hydrogen peroxide concentration range of 0.5 to 69.4 μM using a hydrodynamic amperometric technique. The limit of detection (for a signal-to-noise ratio of 3) and sensitivity were found to be 92 nM and 0.89 μA/μM, respectively. Furthermore, the diffusion coefficient of hydrogen peroxide (D) and catalytic rate constant (k_cat) were calculated.     

Evaluation of polysulfone hollow fibres and ceramic suction samplers as devices for the in situ extraction of soil solution

An investigation was carried out to assess the potential of using polysulfone hollow fibres for the extraction of soil solution. In comparison to ceramic suction samplers the fibres were shown to contain very low levels of potential contaminants and a low exchange capacity. Carry over between individual samples was negligible permitting the accurate monitoring of temporal changes in solution chemistry. Their flexible and root sized nature makes them ideal for sampling small soil volumes. Some concern however remains about retention of colloidal Fe at the fibre interface. When comparing the soil solution of samples extracted with polysulfone fibres with those extracted by ceramic suction samplers, no significant differences in solute concentrations were observed. No sample contamination resulting from dissolution of Al or Si from the ceramic cup was detected. Analysis of soil solutions collected over a number of extractions, and during and after a rainfall event showed concentrations of elements in solution to remain relatively constant with time.     

Oxide-Based Solid-State Batteries: A Perspective on Composite Cathode Architecture

The garnet-type phase Li₇La₃Zr₂O₁₂ (LLZO) attracts significant attention as an oxide solid electrolyte to enable safe and robust solid-state batteries (SSBs) with potentially high energy density. However, while significant progress has been made in demonstrating compatibility with Li metal, integrating LLZO into composite cathodes remains a challenge. The current perspective focuses on the critical issues that need to be addressed to achieve the ultimate goal of an all-solid-state LLZO-based battery that delivers safety, durability, and pack-level performance characteristics that are unobtainable with state-of-the-art Li-ion batteries. This perspective complements existing reviews of solid/solid interfaces with more emphasis on understanding numerous homo- and heteroionic interfaces in a pure oxide-based SSB and the various phenomena that accompany the evolution of the chemical, electrochemical, structural, morphological, and mechanical properties of those interfaces during processing and operation. Finally, the insights gained from a comprehensive literature survey of LLZO–cathode interfaces are used to guide efforts for the development of LLZO-based SSBs.     

Selection of ceramic fluorapatite‐binding peptides from a phage display combinatorial peptide library: optimum affinity tags for fluorapatite chromatography

Peptide affinity tags have become efficient tools for the purification of recombinant proteins from biological mixtures. The most commonly used ligands in this type of affinity chromatography are immobilized metal ions, proteins, antibodies, and complementary peptides. However, the major bottlenecks of this technique are still related to the ligands, including their low stability, difficulties in immobilization, and leakage into the final products. A model approach is presented here to overcome these bottlenecks by utilizing macroporous ceramic fluorapatite (CFA) as the stationary phase in chromatography and the CFA‐specific short peptides as tags. The CFA chromatographic materials act as both the support matrix and the ligand. Peptides that bind with affinity to CFA were identified from a randomized phage display heptapeptide library. A total of five rounds of phage selection were performed. A common N‐terminal sequence was found in two selected peptides: F4‐2 (KPRSMLH) and F5‐4 (KPRSVSG). The peptide F5‐4, displayed by more than 40% of the phages analyzed in the fifth round of selection, was subjected to further studies. Selectivity of the peptide for the chemical composition and morphology of CFA was assured by the adsorption studies. The dissociation constant, obtained from the F5‐4/CFA adsorption isotherm, was in the micromolar range, and the maximum capacity was 39.4 nmol/mg. The chromatographic behavior of the peptides was characterized on a CFA stationary phase with different buffers. Preferential affinity and specific retention properties suggest the possible application of the phage‐derived peptides as a tag in CFA affinity chromatography for enhancing the selective recovery of proteins. Copyright © 2013 John Wiley & Sons, Ltd.     

氧化锆全瓷和金属烤瓷冠修复对牙冠延长术后牙周状况的影响

目的:研究氧化锆全瓷和金属烤瓷冠修复对牙冠延长术后牙周状况的影响,为临床治疗提供依据。方法:选取2014年12月到2015年2月我院收治牙冠延长术联合牙冠修复治疗患者210例,按照随机数字表法将患者分为研究组和对照组,每组105例,研究组应用氧化锆全瓷,对照组应用金属烤瓷,比较两组牙周情况、佩戴修复体时间和康复时间。结果:研究组正常者比例为83.81%(88/105)显著高于对照组的65.71%(69/105),轻度病损者比例为8.57%(9/105)显著低于对照的21.90%(23/105),比较差异具有统计学意义(P0.05);研究组术后佩戴修复体时间和康复时间均显著短于对照组,比较差异具有统计学意义(P0.05)。结论:应用氧化锆全瓷修复能改善牙冠延长术后患者牙周情况,缩短佩戴修复体时间和康复时间。     

Valorization of Foundry Sand in Clay Bricks at Industrial Scale

In this article, foundry sand as waste material has been valorized in ceramic brick manufacturing at industrial scale. The employment of a waste coming from one industry as an input for another is one of the key concepts of industrial ecology. To study the environmental behavior of the ceramic bodies in different life cycle stages, three leaching tests have been developed. We used an EN 12457 equilibrium leaching test with distilled water and a Wastewater Technology Centre acid neutralization capacity (WTC‐ANC) leaching test with different acidic leachates to carry out the environmental evaluation under different granular scenarios to ascertain the possibilities of the reuse or disposal of this granular material at the end of its useful life (end‐of‐life stage). Finally, we used a NEN 7345 diffusion leaching test for construction materials, with the aim of studying the environmental assessment at the use stage. Regulated pollutants in both stages have been evaluated. Furthermore, other soluble salts have been analyzed because they are closely related to the efflorescence phenomenon in bricks. Results indicate that core and green sand from the foundry industry can be used to replace clay content in construction materials, and that these foundry‐sand‐based ceramics improve some soluble salt results. Despite this fact, at the end‐of‐life stage in an inert waste landfill, lead, arsenic and chromium can be an environmental problem, both for commercial bricks and for foundry‐sand‐based bricks. This work can contribute to the determination of viability of sustainable processes of brick manufacturing that use foundry wastes as raw materials.     

Proteome analysis by bio-active ceramic water in rat liver: contribution to antioxidant enzyme expression, SOD I

The purpose of this study was to investigate the protective effect of bio-active ceramic water on rat liver. Male Wistar rats were divided into 4 groups of 15 animals each. Groups 1 and 2 were fed bio-active ceramic water and tap water for 4 months, respectively. Groups 3 and 4 were treated with the same condition for 12 months. The changes of protein expression of these four groups were investigated using two-dimensional gel electrophoresis and matrix-assisted laser desorption/ionization-time of flight mass spectrometry. Eleven proteins were significantly up-regulated in bio-active ceramic water treated rat liver including aldehyde dehydrogenase I and II, albumin, fructose-1,6-bisphosphatase, and superoxide dismutase I (SOD I). The most highly expressed protein, SOD I with up-regulated enzyme activity, was confirmed by immunoblots as a major antioxidant capable of detoxifying normally generated reactive oxygen species. These data suggest that modified protein expression of the liver contributes to enhance liver function.     

Less harmful acidic degradation of poly(lacticco-glycolic acid) bone tissue engineering scaffolds through titania nanoparticle addition

In the last 10 years, biodegradable aliphatic polyesters, such as poly(lactic-co-glycolic acid) (PLGA), have attracted increasing attention for their use as scaffold materials in bone tissue engineering because their degradation products can be removed by natural metabolic pathways. However, one main concern with the use of these specific polymers is that their degradation products reduce local pH, which in turn induces an inflammatory reaction and damages bone cell health at the implant site. Thus, the objective of the present in vitro study was to investigate the degradation behavior of PLGA when added with dispersed titania nanoparticles. The results of this study provided the first evidence that the increased dispersion of nanophase titania in PLGA decreased the harmful change in pH normal for PLGA degradation. Moreover, previous studies have demonstrated that the increased dispersion of titania nanoparticles into PLGA significantly improved osteoblast (bone-forming cell) functions (such as adhesion, collagen synthesis, alkaline phosphatase activity, and calcium-containing minerals deposition). In this manner, nanophase titania-PLGA composites may be promising scaffold materials for more effective orthopedic tissue engineering applications.     

重组毕赤酵母产华根霉脂肪酶的陶瓷膜微滤除菌工艺研究

在重组毕赤酵母生产脂肪酶的提取中,应用并优化了陶瓷膜微滤除茵工艺,确定了最佳条件为膜截留分子量500kDa、膜操作压力0．3Ⅷa、温度20℃、湿菌体含量35％,先对发酵液稀释1．5倍后再进行洗滤。40L处理量的小试结果显示,在5h处理时间内,能获得高达92．70％的酶活回收率。560L处理量的中试放大,酶活回收率为89．91％,耗时5．5h。在膜的清洗与再生中,采用2％NaC10和2％NaOH在60℃、0．3MPa膜压力下进行清洗40min,清水膜通量恢复率为98．14％。陶瓷膜与板框除菌的比较试验发现,两种方法都获得了微生物限量合格的产品和较高的酶活回收率,但陶瓷膜微滤的滤液微生物检出量更低,处理时间较短,动力能耗更低,易与超滤膜耦合提取,废水产生量更少,菌体废渣易于回收,是一种节能减排、清洁环保的新型除茵工艺。     

High-throughput screening of chromatographic separations: III. Monoclonal antibodies on ceramic hydroxyapatite

High-throughput screening (HTS) of chromatography resins for identifying optimal protein purification conditions is becoming an integral part of industrial process development. In this work, ceramic hydroxyapatite (cHA) chromatography of 15 humanized monoclonal antibodies (mAbs) was examined by HTS. MAb binding, as quantified by partition coefficient (K(p)), was measured under 92 combinations of sodium chloride, phosphate, and pH. Binding varied inversely with these variables for all mAbs tested. However, the magnitudes of binding among mAbs under identical conditions varied significantly, showing a >1.5 log range in K(p). Analysis of variance (ANOVA) techniques were used to describe the binding of each mAb as a function of the three screen variables. Linear models relating log K(p) to the pH, log[sodium chloride], and log[phosphate] fit the data for each antibody with 93-96% accuracy. From these models, characteristic charge values for the cation exchange and metal coordination components of the multi-modal mAb/cHA interaction varied twofold across the mAbs, reflecting inherent variability in the number of contacts between a particular mAb and the cHA surface. Furthermore, we reduced the number of test conditions required from 92 to 8 while maintaining an accurate representation of the full binding response surface. This eight-point modeling method accurately predicted the binding behavior of mAbs as well as mAb aggregates, a common impurity in crude mAb preparations. Using this eight-point modeling method, binding and selectivity information for mAb and aggregate can be obtained from less than two milligrams of protein, making the method attractive for early manufacturability assessments.