Near-infrared spectroscopy for bioprocess monitoring and control.

This article describes the calibration of a spectroscopic scanning instrument for the measurement of selected contaminants in a complex biological process stream. Its use is for the monitoring of a process in which contaminants are to be removed selectively by flocculation from yeast cell homogenate. The main contaminants are cell debris, protein, and RNA. A low-cost instrument has been developed for sensitivity in the region of the NIR spectrum (from 1900 to 2500 nm) where preliminary work found NIR signatures from cell debris, protein, and RNA. Calibration models have been derived using a multivariate method for concentrations of these contaminants, such as would be found after the flocculation process. Two strategies were compared for calibrating the NIR instrument. In one case, samples were prepared by adding materials representative of the contaminants to clarified yeast homogenate so the contaminant levels were well known but outside the range of interest. In the other case, where samples were like those from the process stream after flocculation and floc removal, there was uncertainty of analysis of contaminant level, but the calibration was in the range of interest. Calibration using process stream samples gave results close to those derived from traditional assays. When the calibration models were used to predict the contaminant concentrations in previously unseen samples, the correlation coefficients between measurements and predictions were above 90% in all cases but one. The prediction errors were similar to the errors in the traditional assays.     

Pulling or drilling, does size or species matter? An experimental study of prey handling in Octopus dierythraeus ()

The influence of both predator and prey size on the shift from a pulling to a drilling predatory response was examined in the intertidal octopus Octopus dierythraeus, using an experimental program. Additionally, selective drilling, where particular regions of the prey are targeted, was examined for a variety of bivalve and gastropod prey. O. dierythraeus always initially attempted to pull bivalves apart. Shells that were eventually drilled were always subjected to significantly more pulling attempts than those that could be pulled apart, indicating that octopus are willing to expend more energy to access the flesh quickly. There was no defined threshold where bivalve size caused an octopus to switch from a pulling to a drilling response. Instead, there was a broad size range where the octopus could adopt either handling method and it varied for each individual. Octopus may only able to pull open bivalves before the molecular ratchet or ‘catch’ mechanism that many bivalves possess is engaged. This might explain the lack of a relationship between either octopus or bivalve size and the success of pulling, as it is likely that when the bivalves were presented to individual octopus they were either setting the ‘catch’ mechanism, or had already engaged it. O. dierythraeus demonstrated selective drilling on a variety of molluscan prey, with penetration sites differing between prey species. O. dierythraeus targeted the valve periphery, which was the thinnest part of the shell, therefore minimizing handling time. O. dierythraeus always drilled gastropods, but did not target the thinnest regions of the shells, with drill site varying according to the morphology of the prey. Elongate species with pronounced aperture lips were drilled in the apical region, close to the columella on the side of the opercula whereas nonelongate species were drilled immediately above the aperture. The location of drilling sites may represent a trade-off between targeting the most effective places to inject paralyzing secretions and the mechanically simplest places to drill.     

Improvement in separation characteristics of protein precipitates by acoustic conditioning

The effect of acoustic conditioning on the particle size distribution of isoelectric and calcium-ion-precipitated soya protein has been examined in low-residence-time chambers. In a previous study a beat frequency of 5 Hz obtained using a dual-source system of opposing vibrators was determined as giving optimal improvement in particle-settling characteristics for isoelectric soya protein precipitate. In this study the effect of amplitude of vibration, a measure of acoustic power input, and residence time of acoustic conditioning has been examined.Acoustic power input changed the flow pattern in the conditioning chamber from laminar streamline flow to a well-mixed, turbulent pattern. Such a mixing effect promoted the rapid aggregation of fine particles, a process that was modeled on the basis of orthokinetically controlled collisions. The rate of removal of fine particles due to acoustic conditioning was shown to be proportional to a mixing effect that was releated to the acoustic power dissipated per unit volume.The consequences of fine-particle aggregation on the centrifugal recovery of the precipitate are discussed.