An implantable transducer for measuring tension in an anterior cruciate ligament graft.

The goal of this study was to develop a new implantable transducer for measuring anterior cruciate ligament (ACL) graft tension postoperatively in patients who have undergone ACL reconstructive surgery. A unique approach was taken of integrating the transducer into a femoral fixation device. To devise a practical in vivo calibration protocol for the fixation device transducer (FDT), several hypotheses were investigated: (1) The use of a cable versus the actual graft as the means for applying load to the FDT during calibration has no significant effect on the accuracy of the FDT tension measurements; (2) the number of flexion angles at which the device is calibrated has no significant effect on the accuracy of the FDT measurements; (3) the friction between the graft and femoral tunnel has no significant effect on measurement accuracy. To provide data for testing these hypotheses, the FDT was first calibrated with both a cable and a graft over the full range of flexion. Then graft tension was measured simultaneously with both the FDT on the femoral side and load cells, which were connected to the graft on the tibial side, as five cadaver knees were loaded externally. Measurements were made with both standard and overdrilled tunnels. The error in the FDT tension measurements was the difference between the graft tension measured by the FDT and the load cells. Results of the statistical analyses showed that neither the means of applying the calibration load, the number of flexion angles used for calibration, nor the tunnel size had a significant effect on the accuracy of the FDT. Thus a cable may be used instead of the graft to transmit loads to the FDT during calibration, thus simplifying the procedure. Accurate calibration requires data from just three flexion angles of 0, 45, and 90 deg and a curve fit to obtain a calibration curve over a continuous range of flexion within the limits of this angle group. Since friction did not adversely affect the measurement accuracy of the FDT, the femoral tunnel can be drilled to match the diameter of the graft and does not need to be overdrilled. Following these procedures, the error in measuring graft tension with the FDT averages less than 10 percent relative to a full-scale load of 257 N.     

Messy eaters: Swabbing prey DNA from the exterior of inconspicuous predators when foraging cannot be observed

Complex coevolutionary relationships among competitors, predators, and prey have shaped taxa diversity, life history strategies, and even the avian migratory patterns we see today. Consequently, accurate documentation of prey selection is often critical for understanding these ecological and evolutionary processes. Conventional diet study methods lack the ability to document the diet of inconspicuous or difficult‐to‐study predators, such as those with large home ranges and those that move vast distances over short amounts of time, leaving gaps in our knowledge of trophic interactions in many systems. Migratory raptors represent one such group of predators where detailed diet studies have been logistically challenging. To address knowledge gaps in the foraging ecology of migrant raptors and provide a broadly applicable tool for the study of enigmatic predators, we developed a minimally invasive method to collect dietary information by swabbing beaks and talons of raptors to collect trace prey DNA. Using previously published COI primers, we were able to isolate and reference gene sequences in an open‐access barcode database to identify prey to species. This method creates a novel avenue to use trace molecular evidence to study prey selection of migrating raptors and will ultimately lead to a better understanding of raptor migration ecology. In addition, this technique has broad applicability and can be used with any wildlife species where even trace amounts of prey debris remain on the exterior of the predator after feeding.     

Co-segregation of a gene encoding a deletion ligand for Tcrb-V3+ T cells with Mtv-3

A gene encoding the endogenous superantigen Mls^c, which deletes Tcrb-V3⁺ T cells in the NOD inbred mouse strain, was found to co-segregate with Mtv-3 on chromosome 11. This identifies a fourth gene encoding a deletion ligand for Tcrb-V3⁺ T cells and extends recently published observations in support of the hypothesis that a number of endogenous superantigens are the products of Mtv proviruses. Address correspondence and offprint requests to : K. Tomonari.     

Rapid determination of antimicrobial susceptibility patterns ofListeria monocytogenes isolates by the autobac AIS and MIC procedures

A total of 34 isolates ofListeria monocytogenes were tested against ampicillin, cephalothin, chloramphenicol, erythromycin, tetracycline, and penicillin-G using the Autobac 3-h AIS and the Autobac 5-h MIC procedures. The results were compared to susceptibility category interpretations and MICs determined using the Sceptor system. With the Sceptor System, all isolates were interpreted to be moderately susceptible to ampicillin and penicillin-G, and susceptible to the four other antibiotics. With the Autobac AIS, all isolates were interpreted to be susceptible to all the antibiotics except penicillin-G. All but one of the 34 isolates were interpreted to be resistant to penicillin-G with the Autobac AIS test. The remaining isolate was interpreted to be indeterminant. The Autobac AIS test was unsatisfactory for determining the susceptibility ofL. monocytogenes isolates to penicillin-G. The Autobac MIC results correlated well with the MIC results of the Sceptor system provided that the Autobac was programmed as though it were testing enterococci. The Autobac MIC reported penicillin-G MICs in units per milliliter and required the use of a conversion factor to obtain micrograms per milliliter, and did not allow for the testing of erythromycin. The Autobac MIC susceptibility category interpretations must not be used, as they were derived from an outdated susceptibility standard. The Autobac MIC test may be used if the limitations given above are observed.     

Isolation of single taste cells from lingual epithelium

A method is described for obtaining large numbers of isolatedtaste cells with identified polarity from lingual epithelium.The procedure involves incubating lingual epithelium in collagenase,staining the apical surface with fluorescein-conjugated wheatgerm agglutinin (FTTC-WGA), peeling non-gustatory surface epitheliumfrom the underlying taste buds and connective tissue, and dissociatingisolated taste buds with Ca²⁺-free saline. Isolated taste cellsretain their characteristic morphology for at least 30 min afterdissociation, and the apical specialization can be identifiedas a single patch of fluorescence usually located at the tipof an elongate process. Isolated taste cells are amenable tostudy with the patch-clamp technique, and whole-cell patch-clamprecordings show that isolated taste cells have membrane propertiessimilar to taste cells of intact lingual epithelium. Evidenceis presented that FITC-WGA staining does not alter the voltage-dependentionic currents of the taste cell membrane.     

Bivariate optimization of pedalling rate and crank arm length in cycling

The contribution of this paper is a bivariate optimization of cycling performance. Relying on a biomechanical model of the lower limb, a cost function derived from the joint moments developed during cycling is computed. At constant average power, both pedalling rate (i.e. rpm) and crank arm length are systematically varied to explore the relation between these variables and the cost function. A crank arm length of 170 mm and pedalling rate of 100 rpm correspond closely to the cost function minimum. In cycling situations where the rpm deviates from 100 rpm, however, crank arms of length other than 170 mm yield minimum cost function values. In addition, the sensitivity of optimization results to both increased power and anthropometric parameter variations is examined. At increased power, the cost function minimum is more strongly related to the pedalling rate, with higher pedalling rates corresponding to the minimum. Anthropometric parameter variations influence the results significantly. In general it is found that the cost function minimum for tall people occurs at longer crank arm lengths and lower pedalling rates than the length and rate for short people.     

Molecular cloning and characterization of the mouse UDP-N-acetylglucosamine:alpha-3-D-mannoside beta-1,2-N-acetylglucosaminyltransferase I gene.

The biosynthesis of protein-bound complex N-glycans in mammals requires a series of covalent modifications governed by a large number of specific glycosyltransferases and glycosidases. The addition of oligosaccharide to an asparagine residue on a nascent polypeptide chain begins in the endoplasmic reticulum. Oligosaccharide processing continues in the Golgi apparatus to produce a diversity of glycan structures. UDP-N-acetylglucosamine:alpha-3-D-mannoside beta-1,2-N-acetylglucosaminyltransferase I (EC 2.4.1.101; GlcNAc-TI) is a key enzyme in the process because it is essential for the conversion of high-mannose N-glycans to complex and hybrid N-glycans. We have isolated the mouse gene encoding GlcNAc-TI (Mgat-1) from a genomic DNA library. The mouse sequence is highly conserved with respect to the human and rabbit homologs and exists as a single protein-encoding exon. Mgat-1 was mapped to mouse Chromosome 11, closely linked to the gene encoding interleukin-3 by the analysis of multilocus interspecies backcrosses. RNA analyses of Mgat-1 expression levels revealed significant variation among normal tissues and cells.