羧基化聚丙烯酸酯接枝邻甲酚环氧丙烯酸树脂的合成

采用JF-220环氧树脂和丙烯酸反应合成邻甲酚环氧丙烯酸树脂(JFA),再将其和羧基化聚丙烯酸酯进一步反应制备羧基化聚丙烯酸酯接枝邻甲酚环氧丙烯酸树脂(CAJFA)。研究了催化剂、阻聚剂和反应温度对合成反应的影响,确定了每步反应的最佳合成条件,并且对JF-220树脂、JFA树脂和CAJFA树脂的结构进行了IR表征。     

爬山虎红色素的大孔树脂吸附和分离及理化性质研究

本文比较了六种不同型号的大孔树脂对爬山虎红色素的吸附能力,筛选其中最佳的HPD600树脂作为爬山虎红色素的吸附和分离的树脂;用甲醇作为洗脱剂,洗脱效果好;研究了食品中几种常见的共存物、几种金属离子、氧化剂、温度及光等对爬山虎红色素稳定性的影响。     

酵母菌对高浓度味精废水的处理条件研究

对作者实验室分离到的3种酵母菌混合处理味精生产废水的条件进行了研究,结果表明最佳处理条件为:pH值4.0、温度28℃、时间20h、接种量10%,COD去除率可达到82.9%。并对处理后的酵母菌菌体进行了饲料评价,发现混合菌体含有丰富的蛋白质、脂肪含量小等优点。该技术作为预处理应用于实际工程中将取得较好的处理效果并产生一定的经济效益。     

Effect of flask closure method and post‐pressing time on the upper denture base adaptation

doi:10.1111/j.1741‐2358.2009.00307.x
Effect of flask closure method and post‐pressing time on the upper denture base adaptation Objectives: The purpose of this study was to evaluate the effect of flask‐closure methods, post‐pressing times and acrylic resins on denture base adaptation. Materials and methods: The resins were flasked using a hydraulic press and closed with the traditional clamp or RS system. Conventional heat‐cure resin was polymerised immediately or at 6 h post‐pressing at 74°C for 9 h. Rapid cycle heat‐cure resin was polymerised in boiling water for 20 min. After cooling, the bases were deflasked and the sets of cast‐base transversally sectioned in the regions distal to the canine, mesial to the first molar and in the posterior palatal zone. The adaptation was measured with an optical microscope (0.0005 mm) at five reference points for each section. Data were analysed using anova and Tukey’s test (α = 0.05). Results: Traditional clamp and immediate post‐pressing time improved base adaptation for conventional heat‐cure resin. Both post‐pressing times showed most accurate base adaptation for conventional heat‐cure resin when the traditional clamp was used. Immediate post‐pressing time improved base adaptation for conventional heat‐cure resin and the 6‐h delay in time was significant for the rapid cycle heat‐cure resin. Conclusions: Traditional clamp and immediate post‐pressing time improved base adaptation for conventional heat‐cure resin.     

Glass transition temperature of hard chairside reline materials after post‐polymerisation treatments

doi:10.1111/j.1741‐2358.2009.00312.x
Glass transition temperature of hard chairside reline materials after post‐polymerisation treatments Objective: This study evaluated the effect of post‐polymerisation treatments on the glass transition temperature (T_g) of five hard chairside reline materials (Duraliner II‐D, Kooliner‐K, New Truliner‐N, Ufi Gel hard‐U and Tokuso Rebase Fast‐T). Materials and methods: Specimens (10 × 10 × 1 mm) were made following the manufacturers’ instructions and divided into three groups (n = 5). Control group specimens were left untreated. Specimens from the microwave group were irradiated with pre‐determined power/time combinations, and specimens from the water‐bath group were immersed in hot water at 55°C for 10 min. Glass transition (°C) was performed by differential scanning calorimetry. Data were analysed using anova, followed by post hoc Tukey’s test (α = 0.05). Results: Both post‐polymerisation treatments promoted a significant (p < 0.05) increase in the T_g of reline material K. Materials K, D and N showed the lowest T_g (p < 0.05). No significant difference between T and U specimens was observed. Conclusion: Post‐polymerisation treatments improved the glass transition of material Kooliner, with the effect being more pronounced for microwave irradiation.     

Recyclable Merrifield resin‐supported organocatalysts containing pyrrolidine unit through A3‐coupling reaction linkage for asymmetric Michael addition

Merrifield resin‐supported pyrrolidine‐based chiral organocatalysts A ? D through A³‐coupling reaction linkage have been developed and found to be highly effective catalysts for the Michael addition reaction of ketones with nitrostyrenes. The reactions generated the corresponding products in good yields (up to 92%), excellent enantioselectivities (up to 98% ee), and high diastereoselectivities (up to 99:1 dr). In addition, the catalysts can be reused at least five times without a significant loss of catalytic activity and stereoselectivity. Chirality, 2010. © 2009 Wiley‐Liss, Inc.     

Variation in E- and Z-guggulsterones of Commiphora wightii

The seasonal and geographical variations in guggulsterone content in oleo-gum resin have been examined in order to determine the optimum collection time and to identify suitable locations for large-scale cultivation of Commiphora wightii. The results clearly showed that E- and Z-guggulsterones varied significantly on seasonal basis. A higher guggulsterone concentration was observed during summer (May–July) and this was lower during winter (November–March). A wide variation in guggulsterone content was also observed in the different geographical regions in Rajasthan. The southern part of the state produced the lowest guggulsterone (< 1.19%) whereas the central, northern and western regions had higher yields (1.87–2.76%). The guggulsterone yield exhibited a positive correlation with annual rainfall between 15 and 55 cm and declined in the regions with higher rainfall (> 60 cm). Plants with high guggulsterone content can be utilized for mass multiplication and genetic improvement.     

大孔树脂吸附法分离海金沙总黄酮的研究

用大孔树脂吸附法分离海金沙中的总黄酮,考查了解吸剂浓度、吸附固液比(g/mL)、吸附温度和吸附时间对海金沙总黄酮提取率的影响。结果表明:用70%乙醇作解吸剂,在吸附固液比为1∶6(g/mL),50℃温度下吸附90 min,总黄酮提取率为1.81%。