Li+ Pre‐Insertion Leads to Formation of Solid Electrolyte Interface on TiO2 Nanotubes That Enables High‐Performance Anodes for Sodium Ion Batteries

Recently, sodium ion batteries (SIBs) have been widely investigated as one of the most promising candidates for replacing lithium ion batteries (LIBs). For SIBs or LIBs, designing a stable and uniform solid electrolyte interphase (SEI) at the electrode–electrolyte interface is the key factor to provide high capacity, long‐term cycling, and high‐rate performance. In this paper, it is described how a remarkably enhanced SEI layer can be obtained on TiO₂ nanotube (TiO₂ NTs) arrays that allows for a strongly improved performance of sodium battery systems. Key is that a Li⁺ pre‐insertion in TiO₂ NTs can condition the SEI for Na⁺ replacement. SIBs constructed with Li‐pre‐inserted NTs deliver an exceptional Na⁺ cycling stability (e.g., 99.9 ± 0.1% capacity retention during 250 cycles at a current rate of 50 mA g^?1) and an excellent rate capability (e.g., 132 mA h g^?1 at a current rate of 1 A g^?1). The key factor in this outstanding performance is that Li‐pre‐insertion into TiO₂ NTs leads not only to an enhanced electronic conductivity in the tubes, but also expands the anatase lattice for facilitated subsequent Na⁺ cycling.     

In Situ Conversion of Cu3P Nanowires to Mixed Ion/Electron‐Conducting Skeleton for Homogeneous Lithium Deposition

The introduction of 3D wettable current collectors is one of the practical strategies toward realizing high reversibility of lithium (Li) metal anodes, yet its effect is usually insufficient owing to single electron‐conductive skeleton. Here, homogeneous Li deposition behavior and enhanced Coulombic efficiency is reported for electrochemically lithiated Cu₃P nanowires, owing to the formation of a mixed ion/electron‐conducting skeleton (MIECS). In particular, by evaluating the Gibbs free energy change, the possible chemical reaction between Cu₃P and molten Li is used to construct a MIECS containing Li₃P and Cu–Li alloy phase. The successful conversion of Cu₃P nanowires to Li₃P and Cu–Li alloy nanocomposite not only greatly reduces the surface energy between molten Li and Cu₃P, but also induces uniform Li stripping/plating behavior via balanced ion/electron transport. Thus, the as‐obtained Li@MIECS composite anode displays superior cycling stability in both symmetric cells and full cells. This work provides a promising option for the preparation of high‐performance composite Li anodes containing MIECS by thermally pre‐storing Li.     

Oxygen‐Deficient Blue TiO2 for Ultrastable and Fast Lithium Storage

Developing a titanium dioxide (TiO₂)‐based anode with superior high‐rate capability and long‐term cycling stability is important for efficient energy storage. Herein, a simple one‐step approach for fabricating blue TiO₂ nanoparticles with oxygen vacancies is reported. Oxygen vacancies can enlarge lattice spaces, lower charge transfer resistance, and provide more active sites in TiO₂ lattices. As a result, this blue TiO₂ electrode exhibits a highly reversible capacity of 50 mAh g^?1 at 100 C (16 800 mA g^?1) even after 10 000 cycles, which is attributable to the combination of surface capacitive process and remarkable diffusion‐controlled insertion revealed by the kinetic analysis. The strategy of employing oxygen‐deficient nanoparticles may be extended to the design of other robust semiconductor materials as electrodes for energy storage.     

Superior Oxygen Reduction Reaction on Phosphorus‐Doped Carbon Dot/Graphene Aerogel for All‐Solid‐State Flexible Al–Air Batteries

Carbon dots have been recognized as one of the most promising candidates for the oxygen reduction reaction (ORR) in alkaline media. However, the desired ORR performance in metal–air batteries is often limited by the moderate electrocatalytic activity and the lack of a method to realize good dispersion. To address these issues, herein a biomass‐deriving method is reported to achieve the in situ phosphorus doping (P‐doping) of carbon dots and their simultaneous decoration onto graphene matrix. The resultant product, namely P‐doped carbon dot/graphene (P‐CD/G) nanocomposites, can reach an ultrahigh P‐doping level for carbon nanomaterials. The P‐CD/G nanocomposites are found to exhibit excellent ORR activity, which is highly comparable to the commercial Pt/C catalysts. When used as the cathode materials for a primary liquid Al–air battery, the device shows an impressive power density of 157.3 mW cm^?2 (comparing to 151.5 mW cm^?2 of a similar Pt/C battery). Finally, an all‐solid‐state flexible Al–air battery is designed and fabricated based on our new nanocomposites. The device exhibits a stable discharge voltage of ≈1.2 V upon different bending states. This study introduces a unique biomass‐derived material system to replace the noble metal catalysts for future portable and wearable electronic devices.     

Nonwoven rGO Fiber‐Aramid Separator for High‐Speed Charging and Discharging of Li Metal Anode

Li metal, which has a high theoretical specific capacity and low redox potential, is considered to the most promising anode material for next‐generation Li ion‐based batteries. However, it also exhibits a disadvantageous solid electrolyte interphase (SEI) layer problem that needs to be resolved. Herein, an advanced separator composed of reduced graphene oxide fiber attached to aramid paper (rGOF‐A) is introduced. When rGOF‐A is applied, F^? anions, generated from the decomposition of the LiPF₆ electrolyte during the SEI layer formation process form semi‐ionic C? F bonds along the surface of rGOF. As Li⁺ ions are plated, the “F‐doped” rGO surface induces the formation of LiF, which is known as a component of a chemically stable SEI, therefore it helps the Li metal anode to operate stably at a high current of 20 mA cm^?2 with a high capacity of 20 mAh cm^?2. The proposed rGOF‐A separator successfully achieves a stable SEI layer that could resolve the interfacial issues of the Li metal anode.     

Enhanced Kinetics Harvested in Heteroatom Dual‐Doped Graphitic Hollow Architectures toward High Rate Printable Potassium‐Ion Batteries

Carbonaceous materials have emerged as promising anode candidates for potassium‐ion batteries (PIBs) due to overwhelming advantages including cost‐effectiveness and wide availability of materials. However, further development in this realm is handicapped by the deficiency in their in‐target and large‐scale synthesis, as well as their low specific capacity and huge volume expansion. Herein the precise and scalable synthesis of N/S dual‐doped graphitic hollow architectures (NSG) via direct plasma enhanced chemical vapor deposition is reported. Thus‐fabricated NSG affording uniform nitrogen/sulfur co‐doping, possesses ample potassiophilic surface moieties, effective electron/ion‐transport pathways, and high structural stability, which bestow it with high rate capability (≈100 mAh g^?1 at 20 A g^?1) and a prolonged cycle life (a capacity retention rate of 90.2% at 5 A g^?1 after 5000 cycles), important steps toward high‐performance K‐ion storage. The enhanced kinetics of the NSG anode are systematically probed by theoretical simulations combined with operando Raman spectroscopy, ex situ X‐ray photoelectron spectroscopy, and galvanostatic intermittent titration technique measurements. In further contexts, printed NSG electrodes with tunable mass loading (1.84, 3.64, and 5.65 mg cm^?2) are realized to showcase high areal capacities. This study demonstrates the construction of a printable carbon‐based PIB anode, that holds great promise for next‐generation grid‐scale PIB applications.     

Boosting Superior Lithium Storage Performance of Alloy‐Based Anode Materials via Ultraconformal Sb Coating–Derived Favorable Solid‐Electrolyte Interphase

Alloy materials such as Si and Ge are attractive as high‐capacity anodes for rechargeable batteries, but such anodes undergo severe capacity degradation during discharge–charge processes. Compared to the over‐emphasized efforts on the electrode structure design to mitigate the volume changes, understanding and engineering of the solid‐electrolyte interphase (SEI) are significantly lacking. This work demonstrates that modifying the surface of alloy‐based anode materials by building an ultraconformal layer of Sb can significantly enhance their structural and interfacial stability during cycling. Combined experimental and theoretical studies consistently reveal that the ultraconformal Sb layer is dynamically converted to Li₃Sb during cycling, which can selectively adsorb and catalytically decompose electrolyte additives to form a robust, thin, and dense LiF‐dominated SEI, and simultaneously restrain the decomposition of electrolyte solvents. Hence, the Sb‐coated porous Ge electrode delivers much higher initial Coulombic efficiency of 85% and higher reversible capacity of 1046 mAh g^?1 after 200 cycles at 500 mA g^?1, compared to only 72% and 170 mAh g^?1 for bare porous Ge. The present finding has indicated that tailoring surface structures of electrode materials is an appealing approach to construct a robust SEI and achieve long‐term cycling stability for alloy‐based anode materials.