Experimental study of the spray characteristics of biodiesel based on inedible oil

We studied the spray characteristics of inedible oil using experimental and simulation methods. Spray penetration, spray cone angle and spray tip speed were measured at different biodiesel ratios in a constant volume vessel with wide visualization and high back pressure, using a high-speed camera. The characteristics of biodiesel spray were simulated under the same conditions using Star-CD software. The experimental results showed that, as the ratio of biodiesel in the blends increased, spray penetration and spray speed increased, but the spray cone angle decreased. Throughout the spray injection period, the region at 0.05–0.475S (spray tip penetration) was a key area affecting spray cone angle. From 0.8 ms after injection, the spray penetration deviation ratios started to increase with increasing biodiesel blend ratios. Simulation results showed similar macroscopic spray characteristics to the experimental results for jatropha oil. The results also showed that the Sauter mean diameter of blend fuels was greater than that of diesel, and spray was more concentrated, due to the higher viscosity and surface tension of the biodiesel, compared with conventional diesel fuel. The macroscopic and microscopic spray properties of blended fuels containing 5%, 10% and 20% biodiesel were similar to diesel.     

High‐Performance Thick‐Film All‐Polymer Solar Cells Created Via Ternary Blending of a Novel Wide‐Bandgap Electron‐Donating Copolymer

A novel wide‐bandgap electron‐donating copolymer containing an electron‐deficient, difluorobenzotriazole building block with a siloxane‐terminated side chain is developed. The resulting polymer, poly{(4,8‐bis(4,5‐dihexylthiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene‐co‐4,7‐di(thiophen‐2‐yl)‐5,6‐difluoro‐2‐(6‐(1,1,1,3,5,5,5‐heptamethyltri‐siloxan‐3‐yl)hexyl)‐2H‐benzo[d][1,2,3]triazole} (PBTA‐Si), is used to successfully fabricate high‐performance, ternary, all‐polymer solar cells (all‐PSCs) insensitive to the active layer thickness. An impressively high fill factor of ≈76% is achieved with various ternary‐blending ratios. The optimized all‐PSCs attain a power conversion efficiency (PCE) of 9.17% with an active layer thickness of 350 nm and maintain a PCE over 8% for thicknesses over 400 nm, which is the highest reported efficiency for thick all‐PSCs. These results can be attributed to efficient charge transfer, additional energy transfer, high and balanced charge transport, and weak recombination behavior in the photoactive layer. Moreover, the photoactive layers of the ternary all‐PSCs are processed in a nonhalogenated solvent, 2‐methyltetrahydrofuran, which greatly improves their compatibility with large‐scale manufacturing.     

Growth model for raceway pond cultivation of Desmodesmus sp. MCC34 isolated from a local water body

Biofuel production by microalgae has the advantage of higher biomass productivity over land crops. The selection of potential microalgae depends on the growth in outdoor mass cultivation during different seasons, which can be predicted by a mathematical model. Here, freshwater green algae were isolated from a local water body in Pilani, Rajasthan, India (geographical coordinates: 28°22′N 75°36′E) and characterized by microscopy and ribosomal RNA analysis. The strain was submitted to the Indian Agricultural Research Institute's microbial culture collection (IARI, India) and identified as Desmodesmus sp. MCC34. This strain, along with a fresh water green algae (Chlorella minutissima), two marine green algae species (Dunaliella salina and Dunaliella tertiolecta) and two nitrogen fixing cyanobacteria (Nostoc muscorum and Anabaena doliolum), were screened for lipid productivity and growth kinetics under culture room and raceway pond conditions. Desmodesmus sp. MCC34 showed the highest specific growth rate (0.26 day^?1), biomass production (1.9 g L^?1) and lipid productivity (103 mg L^?1 day^?1). The optimal temperature and saturating light intensity for maximal growth of Desmodesmus sp. MCC34 were 35 °C and 75 μmol m^?2 s^?1 with molar extinction coefficient of 0.22 m² g^?1, respectively. Desmodesmus sp. MCC34 was then subjected to outdoor cultivation in a 20‐m long raceway pond for 18 days during March and November 2013. The areal biomass productivity and volumetric biomass productivity were 13946.23 kg ha^?1 year^?1 and 56.94 mg L^? 1day^?1 during the month of March, decreasing to 6262.28 kg ha^?1 year^?1 and 25.57 mg L^? 1day^?1 during the month of November. A mathematical model was constructed to explain the relationship between biomass production and growth parameters such as temperature, light intensity and nutrient concentration. The productivity values predicted with the proposed model correspond well with the experimental data, suggesting the validity of the model.     

A Brønsted acidic ionic liquid as an efficient and environmentally benign catalyst for biodiesel synthesis from free fatty acids and alcohols

Biodiesel could be synthesized using Brønsted acidic ionic liquid N-methyl-2-pyrrolidonium methyl sulfonate ([NMP][CH₃SO₃]) as a catalyst, specially with free long-chain fatty acids or their mixtures, as well as with low-molecular weight alcohols as substrates. This catalyst showed good catalytic and reusable performance under mild conditions and without any additional organic solvent. The ionic liquid could be reused eight times after the water in the ionic liquid was removed. The yields of fatty acid alkyl esters could reach between 93.6% and 95.3% after the esterifications were carried out at 70 °C for 8 h. Therefore, an efficient and environmentally friendly catalyst was provided for the synthesis of biodiesel from low-cost feedstocks such as waste oils.     

Biodiesel production,properties, and feedstocks

Biodiesel, defined as the mono-alkyl esters of vegetable oils or animal fats, is an environmentally attractive alternative to conventional petroleum diesel fuel (petrodiesel). Produced by transesterification with a monohydric alcohol, usually methanol, biodiesel has many important technical advantages over petrodiesel, such as inherent lubricity, low toxicity, derivation from a renewable and domestic feedstock, superior flash point and biodegradability, negligible sulfur content, and lower exhaust emissions. Important disadvantages of biodiesel include high feedstock cost, inferior storage and oxidative stability, lower volumetric energy content, inferior low-temperature operability, and in some cases, higher NO _x exhaust emissions. This review covers the process by which biodiesel is prepared, the types of catalysts that may be used for the production of biodiesel, the influence of free fatty acids on biodiesel production, the use of different monohydric alcohols in the preparation of biodiesel, the influence of biodiesel composition on fuel properties, the influence of blending biodiesel with other fuels on fuel properties, alternative uses for biodiesel, and value-added uses of glycerol, a co-product of biodiesel production. A particular emphasis is placed on alternative feedstocks for biodiesel production. Lastly, future challenges and outlook for biodiesel are discussed. Disclaimer: Product names are necessary to report factually on available data; however, the USDA neither guarantees nor warrants the standard of the product, and the use of the name by USDA implies no approval of the product to the exclusion of others that may also be suitable.     

Light Harvesting at Oblique Incidence Decoupled from Transmission in Organic Solar Cells Exhibiting 9.8% Efficiency and 50% Visible Light Transparency

For many years, it has been recognized that potential organic photovoltaic cells must be integrated into elements requiring high transparency. In most of such elements, sunlight is likely to be incident at large angles. Here it is demonstrated that light transmission can be largely decoupled from harvesting by optically tailoring an infrared shifted nonfullerene acceptor based organic cell architecture. A 9.67% power conversion efficiency at 50° incidence is achieved together with an average visual transmission above 50% at normal incidence. The deconstruction of a 1D nanophotonic structure is implemented to conclude that just two λ/4 thick layers are essential to reach, for a wide incidence angle range, a higher than 50% efficiency increase relative to the standard configuration reference. In an outdoor measurement of vertically positioned 50% visible transparent cells, it is demonstrated that 9.80% of sunlight energy can be converted into electricity during the course of 1 day.     

Predicting the Mechanical and Electrical Properties of Nanocomposites Formed from Polymer Blends and Nanorods

By integrating different simulation techniques, we investigate the self-assembly and macroscopic properties of nanocomposites composed of nanoscale rods and a binary polymer blend. In particular, we combine a Cahn–Hilliard (CH) theory for binary mixtures and a Brownian dynamics (BD) for nanorods to create a hybrid model that allows us to determine the structural evolution of the nanocomposite. The incorporation of the nanorods into the minority phase of the phase-separating blend yields a bicontinuous morphology, where the nanorods form a percolating network within the continuous minority phase. This morphology serves as the input to a lattice spring model (LSM), which is used to determine the mechanical properties, and a finite difference model (FDM), which is used to calculate the electrical conductance of the material. We find that in this doubly percolating system, the reinforcement efficiency of the nanorods and the electrical conductivity of the material are significantly increased relative to the behavior in composites where the nanorods are randomly dispersed in a homogeneous matrix. The integration of these various techniques allow us to predict the complex nanorod/polymer morphologies as a function of the constituents' characteristics, determine the mechanical and electrical, behavior of the resultant material and consequently relate the nanoscopic structure of the mixture to the macroscopic properties of the composite.     

Effect of chemical complexity of essential oils on feeding deterrence in larvae of the cabbage looper

The relationship between chemical composition and feeding deterrent activity of seven essential oils is explored, including those from Syzygium aromaticum (L.) Merr. & Perry (Myrtaceae), Cinnamomum zeylanicum Blume (Lauraceae), Lavendula latifolia (L.) Medicus, Lavendula angustifolia L., Mentha crispa L., Mentha arvensis L. and Mentha piperita L. (Lamiaceae) against an important agricultural pest, the cabbage looper (Trichoplusia ni Hübner, Noctuidae), using a leaf‐disc choice bioassay. Comparison of the deterrent activity of ‘full mixtures' with respective artificial blends missing individual constituents demonstrates that, for most oils, minor constituents in a mixture can be as important as major constituents with respect to the overall feeding deterrent effect. There is a lack of correlation between the feeding deterrent effect of an individual constituent of an essential oil and its contribution to the overall activity of the ‘full mixture’ in some cases. The effect of removing an individual constituent from the mixture of an essential oil depends on the unique properties of the mixture, which in turn may reflect the interaction of its constituents. Understanding the role and contribution of each constituent to the overall activity of the oil can facilitate the creation of artificial blends that optimize their efficacy against different pests.     

Relative quantitative PCR to assess bacterial community dynamics during biodegradation of diesel and biodiesel fuels under various aeration conditions

The degradation of diesel fuel, B20 blend and biodiesel in liquid cultures by a seven-member bacterial consortium was compared under conditions with full aeration or with limited aeration with nitrate added as main electron acceptor. Community dynamics was assessed employing real-time PCR and the ddCt method for relative quantification. Biodegradation rates increased with increasing biodiesel content, but were significantly reduced under conditions with nitrate. Despite large variations in biodegradation rates, magnitude changes in population numbers were typically observed only from zero to one order, regardless the type of fuel and electron acceptor. Only Comamonadaceae and Variovorax sp. distinctly preferred aerobic conditions, and during aerobic growth showed suppression as fuel contained more biodiesel. Thus, the consortium is relatively stable and most of the degraders can shift their metabolism from hydrocarbons to biodiesel. The stability of the consortium is of interest in the context of biodiesel-mediated biodegradation of petroleum hydrocarbons.