固定化酶的微环境效应—载体离子基团性质的影响

作者合成了阴离子型和阳离子型葡聚糖,以此为载体,用CNBr活化其剩余羟基,固定化了葡萄糖淀粉酶和葡萄糖异构酶。就离子型载体对固定化酶的蛋白载量、最适pH和热稳定性等的影响做了考察。发现固定化酶的蛋白载量不仅与载体的电性质有关,也与酶分子自身的电性质有关。当载体电性质与酶蛋白电性质相反时,固定化酶的蛋白载量增加,热稳定性提高、载体电性质与酶蛋白电性质相同时,固定化酶的蛋白载量不变或下降,其热稳定性不变。作者还发现当离子型载体孔度和体系缓冲液浓度一定时,酶分子能否进入多孔性载体内部,对其最适pH是否变化影响极大。若酶分子仅被连接在载体的外表层,其最适pH不发生变化,反之亦然。作者还观察到当多糖类载体引入氨基或羧基后,大大增强了其抵抗微生物侵蚀的能力。     

染色体辐射效应的微机检测 Ⅱ断片率 微核率与细胞畸变率间的相关性检测

本文继前文后,按照设计的线性回归程序在“IBM—PC/XT”微型计算机上,进一步检测了断片率、微核率与细胞畸变率之间的相关性,肯定了微核测定法,断片测定法可以替代染色体畸变分析法。     

广东汉族健康人载脂蛋白AⅠ-CⅢl-AⅣ基因簇DNA多态性及其单倍型分布

本文研究了中国广东汉族健康人群apoAI-CⅢ-AIV基因簇DNA限制性内切酶PstI、SstI和EcoRI片段长度多态性。其中等位基因P_1,P_2,S_1,S_2,R_1和R_2的频率分别为0.98,0.02,0.96,0.04,0.90和0.10。经卡方检验符合Hardy-Weinbery氏遗传平衡,与其他种族比较,本文结果显示中国广东汉族人P_2等位基因频率低于日本人、亚洲印第安人和高加索人,S_2等位基因频率低于日本人、菲律宾人、沙特阿拉伯人和亚洲印第安人,而与高加索人相近,R_2等位基因频率稍高于高加索人。不同种族间apoAI-CⅢ-AIV基因簇DNA多态频率无疑存在差异,这种差异可能是由于遗传漂变和自然选择单独或联合作用所致。对P_1、P_2,S_1、S_2和R_1、R_2构成的单倍型和连锁平衡程度进行了分析,结果显示这些单倍型处于连锁不平衡状态。     

Differing activities of medullary respiratory neurons in eupnea and gasping

Our purpose was to compare further eupneic ventilatory activity with that of gasping. Decerebrate, paralyzed, and ventilated cats were used; the vagi were sectioned within the thorax caudal to the laryngeal branches. Activities of the phrenic nerve and medullary respiratory neurons were recorded. Antidromic invasion was used to define bulbospinal, laryngeal, or not antidromically activated units. The ventilatory pattern was reversibly altered to gasping by exposure to 1% carbon monoxide in air. In eupnea, activities of inspiratory neurons commenced at various times during inspiration, and for most the discharge frequency gradually increased. In gasping, the peak discharge frequency of inspiratory neurons was unaltered. However, all commenced activities at the start of the phrenic burst and reached peak discharge almost immediately. The discharge frequencies of all groups of expiratory neurons fell in gasping, with many neurons ceasing activity entirely. These data are consistent with the hypothesis that brain stem mechanisms controlling eupnea and gasping differ fundamentally.     

Insulin suppresses hepatitis B surface antigen expression in human hepatoma cells

The human hepatoma Hep3B cells contain integrated hepatitis B viral genome and continually secret hepatitis B surface antigen (HBsAg). The production of HBsAg (but not alpha-fetoprotein) was suppressed by addition of low concentrations (0.1-1 nM) of insulin into serum-free medium. In addition, the suppression of HBsAg production by insulin was paralleled with the decrease in HBsAg mRNA abundance. Insulin also cause a rapid rate of disappearance of HBsAg mRNA (t 1/2, 2 h) in Hep3B cells. The Hep3B cells carry specific receptor with high affinity for insulin (Kd = 1.8 nM). The receptor showed an insulin-dependent protein tyrosine kinase activity. The half-maximal insulin concentration for the activation of the receptor kinase was about 5 nM. Only very high concentrations of insulin-like growth factor I and human proinsulin can compete for the insulin receptor binding and suppress HBsAg production, this suggests that insulin may act through its receptor binding to suppress HBsAg expression in human hepatoma Hep3B cells.     

Optimal door fitting with systematic fixture adjustment

A systematic approach is presented to obtain the best door gap quality through optimal door fitting in automobile body manufacturing. First, three indexes of gap quality are defined; they are: (1) door gap width deviation relative to design nominal; (2) door gap parallelism; and (3) car-to-car gap consistency. Then the door-fitting problem is formulated into a general constrained optimization problem. The effects of optimal door fitting on the three quality indexes are evaluated through computer simulation. These results provide a lower bound on the design of nominal door gap by considering process capability. Finally, a computer-aided fixture adjustment scheme is developed to orient a door in a body side opening to achieve the optimal fitting. The amount of adjustment, with the desired orientation obtained from optimization, is calculated based on parametrically modeled local surface features of the fixture and the door. The adequacy of door feature modeling is verified through a door-fitting experiment.