Action of shear on enzymes: studies with alcohol dehydrogenase.

Yeast alcohol dehydrogenase (ADH) solutions (approximately 1 mg/ml, pH 7) were sheared in a coaxial cylindrical viscometer. This was fitted with a lid sealing the contents from the atmosphere and preventing evaporation. At 30 degrees C after a total of 5 hr intermittent shearing at 683 sec-1 no losses of activity were observed. No losses were found after 5 hr continuous shearing and in a no-shear control. At 40 degrees C and 683 sec-1 there were only small activity losses in 5 hr. Shearing at 3440 sec-1 no measurable losses of activity were found with a 1.03 mg/ml solution in 5 hr at 30 degrees C, a 1.03 mg/ml solution in 8 hr at 5 degrees C, and with a 3.89 mg/ml solution in 3 hr at 5 degrees C. In all these cases, however, a white precipitate formed that was not observed in zero shear control experiments. The sheared 3.89 mg/ml solution was clarified by centrifugation. It was shown that there were no ADH aggregates in the supernatant and that the precipitate was less than 2% of the original protein. At 30 degrees C under adverse pH conditions (pH 8.8) there was no significant difference in activity losses of an approximately 1 mg/ml solution sheared at 65 and 744 sec-1. An approximately 0.5 mg/ml ADH solution, pH 7, was agitated in a small reactor with no free air-liquid interface. Peak shear rates near the impeller were estimated to be about 9000 sec-1. Only a small decrease in specific activity was observed until over 15 hr total running at 5 degrees C.     

Demonstrating the Manufacture of Human CAR‐T Cells in an Automated Stirred‐Tank Bioreactor

Chimeric antigen receptor T‐cell (CAR‐T) therapies have proven clinical efficacy for the treatment of hematological malignancies. However, CAR‐T cell therapies are prohibitively expensive to manufacture. The authors demonstrate the manufacture of human CAR‐T cells from multiple donors in an automated stirred‐tank bioreactor. The authors successfully produced functional human CAR‐T cells from multiple donors under dynamic conditions in a stirred‐tank bioreactor, resulting in overall cell yields which were significantly better than in static T‐flask culture. At agitation speeds of 200 rpm and greater (up to 500 rpm), the CAR‐T cells are able to proliferate effectively, reaching viable cell densities of >5 × 10⁶ cells ml‐1 over 7 days. This is comparable with current expansion systems and significantly better than static expansion platforms (T‐flasks and gas‐permeable culture bags). Importantly, engineered T‐cells post‐expansion retained expression of the CAR gene and retained their cytolytic function even when grown at the highest agitation intensity. This proves that power inputs used in this study do not affect cell efficacy to target and kill the leukemia cells. This is the first demonstration of human CAR‐T cell manufacture in stirred‐tank bioreactors and the findings present significant implications and opportunities for larger‐scale allogeneic CAR‐T production.     

Expansion of human mesenchymal stem cells on microcarriers

The effects on human mesenchymal stem cell growth of choosing either of two spinner flask impeller geometries, two microcarrier concentrations and two cell concentrations (seeding densities) were investigated. Cytodex 3 microcarriers were not damaged when held at the minimum speed, N_JS, for their suspension, using either impeller, nor was there any observable damage to the cells. The maximum cell density was achieved after 8–10 days of culture with up to a 20-fold expansion in terms of cells per microcarrier. An increase in microcarrier concentration or seeding density generally had a deleterious or neutral effect, as previously observed for human fibroblast cultures. The choice of impeller was significant, as was incorporation of a 1 day delay before agitation to allow initial attachment of cells. The best conditions for cell expansion on the microcarriers in the flasks were 3,000 microcarriers ml⁻¹ (ca. 1 g dry weight l⁻¹), a seeding density of 5 cells per microcarrier with a 1 day delay before agitation began at N_JS (30 rpm), using a horizontally suspended flea impeller with an added vertical paddle. These findings were interpreted using Kolmogorov’s theory of isotropic turbulence.     

Scale-down/scale-up studies leading to improved commercial beer fermentation

Scale-up/scale-down techniques are vital for successful and safe commercial-scale bioprocess design and operation. An example is given in this review of recent studies related to beer production. Work at the bench scale shows that brewing yeast is not compromised by mechanical agitation up to 4.5 W/kg; and that compared with fermentations mixed by CO(2) evolution, agitation ≥ 0.04 W/kg is able to reduce fermentation time by about 20%. Work at the commercial scale in cylindroconical fermenters shows that, without mechanical agitation, most of the yeast sediments into the cone for about 50% of the fermentation time, leading to poor temperature control. Stirrer mixing overcomes these problems and leads to a similar reduction in batch time as the bench-scale tests and greatly reduces its variability, but is difficult to install in extant fermenters. The mixing characteristics of a new jet mixer, a rotary jet mixer, which overcomes these difficulties, are reported, based on pilot-scale studies. This change enables the advantages of stirring to be achieved at the commercial scale without the problems. In addition, more of the fermentable sugars are converted into ethanol. This review shows the effectiveness of scale-up/scale-down studies for improving commercial operations. Suggestions for further studies are made: one concerning the impact of homogenization on the removal of vicinal diketones and the other on the location of bubble formation at the commercial scale.     

Process development of human multipotent stromal cell microcarrier culture using an automated high‐throughput microbioreactor

Microbioreactors play a critical role in process development as they reduce reagent requirements and can facilitate high‐throughput screening of process parameters and culture conditions. Here, we have demonstrated and explained in detail, for the first time, the amenability of the automated ambr15 cell culture microbioreactor system for the development of scalable adherent human mesenchymal multipotent stromal/stem cell (hMSC) microcarrier culture processes. This was achieved by first improving suspension and mixing of the microcarriers and then improving cell attachment thereby reducing the initial growth lag phase. The latter was achieved by using only 50% of the final working volume of medium for the first 24 h and using an intermittent agitation strategy. These changes resulted in >150% increase in viable cell density after 24 h compared to the original process (no agitation for 24 h and 100% working volume). Using the same methodology as in the ambr15, similar improvements were obtained with larger scale spinner flask studies. Finally, this improved bioprocess methodology based on a serum‐based medium was applied to a serum‐free process in the ambr15, resulting in >250% increase in yield compared to the serum‐based process. At both scales, the agitation used during culture was the minimum required for microcarrier suspension, N_JS. The use of the ambr15, with its improved control compared to the spinner flask, reduced the coefficient of variation on viable cell density in the serum containing medium from 7.65% to 4.08%, and the switch to serum free further reduced these to 1.06–0.54%, respectively. The combination of both serum‐free and automated processing improved the reproducibility more than 10‐fold compared to the serum‐based, manual spinner flask process. The findings of this study demonstrate that the ambr15 microbioreactor is an effective tool for bioprocess development of hMSC microcarrier cultures and that a combination of serum‐free medium, control, and automation improves both process yield and consistency. Biotechnol. Bioeng. 2017;114: 2253–2266. © 2017 The Authors. Biotechnology and Bioengineering Published by Wiley Periodicals, Inc.     

Comparing a range of impellers for “stirring as foam disruption”

The effectiveness of a range of impellers for “stirring as foam disruption” (SAFD) is assessed in a vessel of 0.72 m diameter and an aspect ratio of 2:1. Measurement of power drawn by the impeller achieving SAFD and of the three-dimensional flow field close to the dispersion surface are both used to explain the findings along with the global gas hold-up. A large radial flow Rushton turbine can disrupt foam at a great height but requires high power. Down-pumping hydrofoils are only effective when the ungassed liquid height is below the level of the impeller employed to disrupt foam. Up-pumping hydrofoils are the most effective because their flow pattern gives rise to high velocities across the dispersion surface, which are able to entrain foam in the downflow generated at the walls.     

Use of multi-staining flow cytometry to characterise the physiological state of Escherichia coli W3110 in high cell density fed-batch cultures.

High cell density fed-batch fermentations of Escherichia coli W3110 have been carried out at specific growth rates of less than 0.3 h-1, to investigate the effect of glucose limitation on the physiological state of individual cells. After an initial exponential batch phase, the feed rate was held constant and a final dry cell weight of approximately 50 g per litre was achieved. The fermentations were monitored by mass spectrometry whilst measurements of pH, DOC, CFU/mL, TCN, OD500nm and residual glucose concentrations were made. Satisfactory and reproducible results were obtained. Flow cytometric analysis of cells in broth samples, based on either of two multi-staining protocols, revealed a progressive change in cell physiological state throughout the course of the fermentations. From these measurements it was concluded that the loss in reproductive viability towards the end of the fed-batch process is due to cell death and not due to the formation of a "viable but nonculturable state" as had previously been reported. Since the presence of a high proportion of dead or dying cells at any time during a fermentation has a detrimental effect on the synthesis of any desired product it is proposed that an on-line flow cytometric analysis and control strategy could be used as a means of increasing overall process efficiency.     

Further studies related to the scale-up of high cell density Escherichia coli fed-batch fermentations: the additional effect of a changing microenvironment when using aqueous ammonia to control pH

In this work, we report on the further development of the scale-down, two-compartment (STR + PFR) experimental simulation model. For the first time, the effect on high cell density Escherichia coli fed-batch fermentations of a changing microenvironment with respect to all three of the major spatial heterogeneities that may be associated with large-scale processing (pH, glucose, and dissolved oxygen concentration) were studied simultaneously. To achieve this, we used traditional microbiological analyses as well as multiparameter flow cytometry to monitor cell physiological response at the individual cell level. It was demonstrated that for E. coli W3110 under such conditions in a 20 m(3) industrial fed-batch fermentation, the biomass yield is lower and final cell viability is higher than those found in the equivalent well-mixed, 5L laboratory scale case. However, by using a combination of the well-mixed 5L stirred tank reactor (STR) with a suitable plug flow reactor (PFR) to mimic the changing microenvironment at the large scale, very similar results to those in the 20 m(3) reactor may be obtained. The similarity is greatest when the PFR is operated with a mean residence time of 50 sec with a low level of dO(2) and a high glucose concentration with either a pH of 7 throughout the two reactors or with pH controlled at 7 in the STR by addition into the PFR where the pH is > 7.     

Application of multi-parameter flow cytometry using fluorescent probes to study substrate toxicity in the indene bioconversion

The bioconversion of indene to cis-(1S,2R) indandiol, a potential key intermediate in the synthesis of Merck's HIV protease inhibitor, CRIXIVAN trade mark, can be achieved using a Rhodococcus strain. This study using Rhodococcus I24 reports on the application of multiparameter flow cytometry for the measurement of cell physiological properties based on cytoplasmic membrane (CM) integrity and membrane depolarization as indicators of toxic effects of the substrate, indene. Quantification of intact polarized CM, intact depolarized CM and permeabilized CM of a large population of bacterial cells has been conducted using specific intracellular and membrane-binding fluorescent stains. Measurements of oxygen uptake rate (OUR) and optical density (OD) as indicators of metabolic activity and biomass growth, respectively, were also made. Indene concentrations of up to 0.25 g/L (0.037 g indene/g dry cell weight) did not significantly (<5% compared to control) affect cell light-scattering properties, intact CM, membrane polarization, respiratory activity, or biomass growth. Between this value and 1.5 g/L (0.221 g indene/g dry cell weight), the changes in intact CM, respiratory activity and biomass growth were relatively insignificant (<5% compared to control), although dissipation of the membrane potential of a significant proportion of the cell population occurred at 0.50 g/L (0.074 g indene/g dry cell weight). At 2.5 g/L (0.368 g indene/g dry cell weight) there was a significant increase in the dead cell population, accompanied by changes in the extracellular cationic concentrations and substantial decrease in respiratory activity. The primary effect of indene toxicity was the disruption of the proton motive force across the cytoplasmic membrane which drives the formation of ATP. The disruption of the proton motive force may have been due to the measured changes in proton permeability across the membrane. In addition, indene may have directly inhibited the membrane-bound enzymes related to respiratory activity. The overall consequence of this was reduced respiratory activity and biomass growth. The cell physiological properties measured via flow cytometry are important for understanding the effects of toxicity at the cellular level which neither measurements of biomass growth or indandiol formation rates can provide since both are cell averaged measurements. The technique described here can also be used as a generic tool for measuring cell membrane properties in response to toxicity of other indene-resistant strains that may be possible to use as recombinant hosts to perform the biotransformation of indene. This study has demonstrated that flow cytometry is a powerful tool for the measurement of cell physiological properties to assess solvent toxicity on whole cell biocatalysts.     

A comparison of high cell density fed-batch fermentations involving both induced and non-induced recombinant Escherichia coli under well-mixed small-scale and simulated poorly mixed large-scale conditions

In this work, multi-parameter flow cytometric techniques, coupled with dual colour fluorescent staining, have been used to study the metabolic consequences of inclusion body formation in high cell density fed-batch cultures of the recombinant E. coli strain MSD3735, producing the IPTG inducible model mammalian protein, AP50. Further, we report on the development of the scale-down, two compartment (STR + PFR) experimental simulation model to study, for the first time, the effect of a changing microenvironment with respect to three of the major spatial heterogeneities that may be associated with large-scale bioprocessing (pH, glucose and dissolved oxygen concentration) on a recombinant bacterial system. Using various time points for induction and various scale-down configurations, it has been shown that inclusion body formation is followed immediately by a detrimental progressive change in individual cell physiological state with respect to both cytoplasmic membrane polarisation and permeability, resulting in a lower final biomass yield. However, the extent of this change was found to be dependent on whether the AP50 protein was induced or not, on the time of induction and on which combination of heterogeneities was being simulated. From this and previous work, it is clear that the scale-down two-compartment model can be used to study the impact of genetically modifying an organism to produce inclusion bodies and any range and combination of potential heterogeneities known to exist at the large scale.