Mechanism and dynamics of conformational ordering in xanthan polysaccharide

The thermally induced order-disorder transition of xanthan (extracellular bacterial polysaccharide from Xanthomonas campestris) has been investigated by optical rotation, differential scanning calorimetry, stopped-flow reaction kinetics and low-angle laser light scattering, and the results have been analysed in terms of Zimm -Bragg helix-coil transition theory. The reciprocal of the transition midpoint temperature (Tm) varies linearly with the logarithm of cation (K+) the salt dependence of Tm, is in agreement with Manning polyelectrolyte theory the ordered structure. The associated increase in cation binding, calculated from the salt dependence of tm, is in agreement with the Manning polyelectrolyte theory for one of the candidate structures from X-ray diffraction, a 5(1) single helix stabilized by packing of side-chains along the polymer backbone, but not for the alternative double-helix structure that has also been proposed. At each salt concentration, the two fundamental parameters of the Zimm -Bragg theory, s and sigma, were calculated. The equilibrium constant for growth of the ordered structure (s) is derived directly from calorimetric measurement of transition enthalpy (delta Hcal ), and sigma, which quantifies the relative instability of the helix nucleus, is derived from the ratio of delta Hcal to the apparent transition enthalpy (delta Happ ) obtained by van't Hoff analysis of the optical rotation data. The temperature course of conformational ordering calculated theoretically is in good quantitative agreement with experimental results from both optical rotation and scanning calorimetry. The calculated average length of stable, ordered chain-sequences increases with decreasing temperature, but equals or exceeds the total chain length from light scattering only at temperatures more than approximately equal to 70 K below Tm, suggesting that ordered and disordered regions may co-exist within the same xanthan molecule. Consistent with this interpretation, the observed rate of conformational ordering increases sharply under conditions where the starting solution for dynamic measurements is partially ordered, suggesting that ordered sequences within each chain may act as helix nuclei for adjacent disordered regions, so that helix growth, rather than the slower nucleation process, becomes rate limiting.     

DNA sequence plays a major role in determining nucleosome positions in yeast CUP1 chromatin.

The role of DNA sequence in determining nucleosome positions in vivo was investigated by comparing the positions adopted by nucleosomes reconstituted on a yeast plasmid in vitro using purified core histones with those in native chromatin containing the same DNA, described previously. Nucleosomes were reconstituted on a 2.5 kilobase pair DNA sequence containing the yeast TRP1ARS1 plasmid with CUP1 as an insert (TAC-DNA). Multiple, alternative, overlapping nucleosome positions were mapped on TAC-DNA. For the 58 positioned nucleosomes identified, the relative positioning strengths and the stabilities to salt and temperature were determined. These positions were, with a few exceptions, identical to those observed in native, remodeled TAC chromatin containing an activated CUP1 gene. Only some of these positions are utilized in native, unremodeled chromatin. These observations suggest that DNA sequence is likely to play a very important role in positioning nucleosomes in vivo. We suggest that events occurring in yeast CUP1 chromatin determine which positions are occupied in vivo and when they are occupied.     

A finite element based method to determine the properties of planar soft tissue.

A finite element based method to determine the incremental elastic material properties of planar membranes was developed and evaluated. The method is applicable to tissues that exhibit inhomogeneity, geometric and material nonlinearity, and anisotropy. Markers are placed on the tissue to form a four-node quadrilateral element. The specimen is loaded to an initial reference state, then three incremental loading sets are applied and the nodal displacements recorded. One of these loadings must include shear. These data are used to solve an over-determined system of equations for the tangent stiffness matrix. The method was first verified using analytical data. Next, data obtained from a latex rubber sheet were used to evaluate experimental procedures. Finally, experiments conducted on preconditioned rat skin revealed nonlinear orthotropic behavior. The vector norm comparing the applied and calculated nodal force vectors was used to evaluate the accuracy of the solutions.     

An implantable transducer for measuring tension in an anterior cruciate ligament graft.

The goal of this study was to develop a new implantable transducer for measuring anterior cruciate ligament (ACL) graft tension postoperatively in patients who have undergone ACL reconstructive surgery. A unique approach was taken of integrating the transducer into a femoral fixation device. To devise a practical in vivo calibration protocol for the fixation device transducer (FDT), several hypotheses were investigated: (1) The use of a cable versus the actual graft as the means for applying load to the FDT during calibration has no significant effect on the accuracy of the FDT tension measurements; (2) the number of flexion angles at which the device is calibrated has no significant effect on the accuracy of the FDT measurements; (3) the friction between the graft and femoral tunnel has no significant effect on measurement accuracy. To provide data for testing these hypotheses, the FDT was first calibrated with both a cable and a graft over the full range of flexion. Then graft tension was measured simultaneously with both the FDT on the femoral side and load cells, which were connected to the graft on the tibial side, as five cadaver knees were loaded externally. Measurements were made with both standard and overdrilled tunnels. The error in the FDT tension measurements was the difference between the graft tension measured by the FDT and the load cells. Results of the statistical analyses showed that neither the means of applying the calibration load, the number of flexion angles used for calibration, nor the tunnel size had a significant effect on the accuracy of the FDT. Thus a cable may be used instead of the graft to transmit loads to the FDT during calibration, thus simplifying the procedure. Accurate calibration requires data from just three flexion angles of 0, 45, and 90 deg and a curve fit to obtain a calibration curve over a continuous range of flexion within the limits of this angle group. Since friction did not adversely affect the measurement accuracy of the FDT, the femoral tunnel can be drilled to match the diameter of the graft and does not need to be overdrilled. Following these procedures, the error in measuring graft tension with the FDT averages less than 10 percent relative to a full-scale load of 257 N.