Mechanism and dynamics of conformational ordering in xanthan polysaccharide

The thermally induced order-disorder transition of xanthan (extracellular bacterial polysaccharide from Xanthomonas campestris) has been investigated by optical rotation, differential scanning calorimetry, stopped-flow reaction kinetics and low-angle laser light scattering, and the results have been analysed in terms of Zimm -Bragg helix-coil transition theory. The reciprocal of the transition midpoint temperature (Tm) varies linearly with the logarithm of cation (K+) the salt dependence of Tm, is in agreement with Manning polyelectrolyte theory the ordered structure. The associated increase in cation binding, calculated from the salt dependence of tm, is in agreement with the Manning polyelectrolyte theory for one of the candidate structures from X-ray diffraction, a 5(1) single helix stabilized by packing of side-chains along the polymer backbone, but not for the alternative double-helix structure that has also been proposed. At each salt concentration, the two fundamental parameters of the Zimm -Bragg theory, s and sigma, were calculated. The equilibrium constant for growth of the ordered structure (s) is derived directly from calorimetric measurement of transition enthalpy (delta Hcal ), and sigma, which quantifies the relative instability of the helix nucleus, is derived from the ratio of delta Hcal to the apparent transition enthalpy (delta Happ ) obtained by van't Hoff analysis of the optical rotation data. The temperature course of conformational ordering calculated theoretically is in good quantitative agreement with experimental results from both optical rotation and scanning calorimetry. The calculated average length of stable, ordered chain-sequences increases with decreasing temperature, but equals or exceeds the total chain length from light scattering only at temperatures more than approximately equal to 70 K below Tm, suggesting that ordered and disordered regions may co-exist within the same xanthan molecule. Consistent with this interpretation, the observed rate of conformational ordering increases sharply under conditions where the starting solution for dynamic measurements is partially ordered, suggesting that ordered sequences within each chain may act as helix nuclei for adjacent disordered regions, so that helix growth, rather than the slower nucleation process, becomes rate limiting.     

Effect of sublethal concentrationsof mercury, cadmium, and copper salts on the lysozyme content in fryof the lena river sturgeon acipenser baeri

The paper presents data on a change in lysozyme content in tissues of spleen, liver and heart in fry of the Lena River sturgeon exposed to the presence of sublethal concentrations of Hg2⁺, Cd²⁺, and Cu²⁺ under conditions of chronic experiment. It has been shown that the lysozyme content in fish tissues varies and has a phasic character. The amplitude of fluctuations of this parameter depends on the moment of sampling, nature of the toxicant, and structural-functional organization of the studied organs.     

Fluctuations of grass pollen content in the atmosphere of East Perugia and meteorological correlations (year 1989)

Summary Gramineae pollination from a pollen monitoring station located in the eastern suburb of Perugia and meteorological correlations are reported. The data refers to the year 1989. Grass pollen peak pollination was from May to July; in this period the influence of relative humidity and of temperature on pollen concentration was very high. Phenological observations, to identify the time of maximum stamen extension in the most common genera in the area, are also reported. During the period of investigation the counts of pollen grains over four-hour periods showed a regular diurnal rhythm with peaks of concentration in the four-hour period 16.00–20.00. Aerosporological data and meteorological data related to four-hour periods were correlated following different criteria.     

An implantable transducer for measuring tension in an anterior cruciate ligament graft.

The goal of this study was to develop a new implantable transducer for measuring anterior cruciate ligament (ACL) graft tension postoperatively in patients who have undergone ACL reconstructive surgery. A unique approach was taken of integrating the transducer into a femoral fixation device. To devise a practical in vivo calibration protocol for the fixation device transducer (FDT), several hypotheses were investigated: (1) The use of a cable versus the actual graft as the means for applying load to the FDT during calibration has no significant effect on the accuracy of the FDT tension measurements; (2) the number of flexion angles at which the device is calibrated has no significant effect on the accuracy of the FDT measurements; (3) the friction between the graft and femoral tunnel has no significant effect on measurement accuracy. To provide data for testing these hypotheses, the FDT was first calibrated with both a cable and a graft over the full range of flexion. Then graft tension was measured simultaneously with both the FDT on the femoral side and load cells, which were connected to the graft on the tibial side, as five cadaver knees were loaded externally. Measurements were made with both standard and overdrilled tunnels. The error in the FDT tension measurements was the difference between the graft tension measured by the FDT and the load cells. Results of the statistical analyses showed that neither the means of applying the calibration load, the number of flexion angles used for calibration, nor the tunnel size had a significant effect on the accuracy of the FDT. Thus a cable may be used instead of the graft to transmit loads to the FDT during calibration, thus simplifying the procedure. Accurate calibration requires data from just three flexion angles of 0, 45, and 90 deg and a curve fit to obtain a calibration curve over a continuous range of flexion within the limits of this angle group. Since friction did not adversely affect the measurement accuracy of the FDT, the femoral tunnel can be drilled to match the diameter of the graft and does not need to be overdrilled. Following these procedures, the error in measuring graft tension with the FDT averages less than 10 percent relative to a full-scale load of 257 N.