Tensile damage and its effects on cortical bone

Plexiform bovine bone samples are repeatedly loaded in tension along their longitudinal axis. In order to induce damage in the bone tissue, bone samples are loaded past their yield point. Half of the bone samples from the damaged group were stored in saline to allow for viscoelastic recovery while the others were decalcified. Tensile tests were conducted on these samples to characterize the effects of damage on the mechanical behavior of the organic matrix (decalcified samples) as well as on bone tissue (stored in saline). The ultimate strain of the damaged decalcified bone is 29% higher compared to that of non-damaged decalcified (control) bone. The ultimate stresses as well as the elastic moduli are similar in both decalcified groups. This phenomenon is also observed in other collagenous tissue (tendon and ligament). This may suggest that damage in bone is caused by shear failure of the organic matrix; transverse separation of the collagen molecules or microfibrils from each other. In contrast, there is a trend towards lowered ultimate strains in damaged bone, which is soaked in saline, with respect to control bone samples (not damaged). The damaged bone tissue exhibits a bi-linear behavior in contrast to the mechanical behavior of non-damaged bone. The initial elastic modulus (below 55 MPa) and ultimate strength of damaged bone are similar to that in non-damaged bone.     

Tensile behavior of cortical bone: dependence of organic matrix material properties on bone mineral content

A porous composite model is developed to analyze the tensile mechanical properties of cortical bone. The effects of microporosity (volksman's canals, osteocyte lacunae) on the mechanical properties of bone tissue are taken into account. A simple shear lag theory, wherein tensile loads are transferred between overlapped mineral platelets by shearing of the organic matrix, is used to model the reinforcement provided by mineral platelets. It is assumed that the organic matrix is elastic in tension and elastic-perfectly plastic in shear until it fails. When organic matrix shear stresses at the ends of mineral platelets reach their yield values, the stress-strain curve of bone tissue starts to deviate from linear behavior. This is referred as the microscopic yield point. At the point where the stress-strain behavior of bone shows a sharp curvature, the organic phase reaches its shear yield stress value over the entire platelet. This is referred as the macroscopic yield point. It is assumed that after macroscopic yield, mineral platelets cannot contribute to the load bearing capacity of bone and that the mechanical behavior of cortical bone tissue is determined by the organic phase only. Bone fails when the principal stress of the organic matrix is reached. By assuming that mechanical properties of the organic matrix are dependent on bone mineral content below the macroscopic yield point, the model is used to predict the entire tensile mechanical behavior of cortical bone for different mineral contents. It is found that decreased shear yield stresses and organic matrix elastic moduli are required to explain the mechanical behavior of bones with lowered mineral contents. Under these conditions, the predicted values (elastic modulus, 0.002 yield stress and strain, and ultimate stress and strain) are within 15% of experimental data.     

Spiro-annulation of barbituric acid derivatives and its analogs by ring-closing metathesis reaction

Barbituric acid 1 and related beta-dicarbonyl compounds were dialkenylated under the phase-transfer catalyst [e.g., benzyltriethylammonium chloride (BTEAC)] conditions to generate the diallylated products. These diallylated products were subjected to the ring-closing metathesis (RCM) reaction to deliver the corresponding spiro-annulated derivatives.     

Changing the structurally effective mineral content of bone with in vitro fluoride treatment

Bovine femur cortical bone specimens were tested in tension after being treated in vitro for 3 days with sodium fluoride solutions of different molarity (0.145, 0.5, and 2.0M). The treatments alter the mechanical properties of the bone samples with different degrees as compared to control samples (untreated). The mechanical properties of the treated samples have lower elastic modulus, yield and ultimate stress, acoustic impedance and hardness, and higher ultimate strain and toughness as compared to control samples. The observed effects were intensified with the increasing molarity of the treatment solutions. This study shows that the fluoride treatment can be used to investigate the composite behavior of bone tissue by altering the structurally important bone mineral content in a controlled manner.     

Effect of bone mineral content on the tensile properties of cortical bone: experiments and theory

The effect of mineral volume fraction on the tensile mechanical properties of cortical bone tissue is investigated by theoretical and experimental means. The mineral content of plexiform, bovine bone was lowered by 18% and 29% by immersion in fluoride solutions for 3 days and 12 days, respectively. The elastic modulus, yield strength and ultimate strength of bone tissue decreased, while the ultimate strain increased with a decrease in mineral content. The mechanical behavior of bone tissue was modeled by using a micromechanical shear lag theory consisting of overlapped mineral platelets reinforcing the organic matrix. The decrease in yield stress, by the 0.002 offset method, of the fluoride treated bones were matched in the theoretical curves by lowering the shear yield stress of the organic matrix. The failure criterion used was based on failure stresses determined from a failure envelope (Mohr's circle), which was constructed using experimental data. It was found that the model predictions of elastic modulus got worse with a decrease in mineral content (being 7.9%, 17.2% and 33.0% higher for the control, 3-day and 12-day fluoride-treated bones). As a result, the developed theory could not fully predict the yield strain of bones with lowered mineral content, being 12.9% and 21.7% lower than the experimental values. The predicted ultimate stresses of the bone tissues with lower mineral contents were within +/- 10% of the experimental values while the ultimate strains were 12.7% and 26.3% lower than the experimental values. Although the model developed in this study did not take into account the presence of hierarchical structures, voids, orientation of collagen molecules and micro cracks, it still indicated that the mechanical properties of the organic matrix depend on bone mineral content.     

Application of the Suzuki-Miyaura cross-coupling reaction for the modification of phenylalanine peptides

We have demonstrated an exceptionally simple and a useful methodology for modification of unusual phenylalanine peptides by adapting the building block approach using the Suzuki-Miyaura cross-coupling reaction as a key step. This strategy gave a good overall yield of various modified tri- and pentapeptides that may be useful to prepare various biologically active peptides in a short period of time.     

Experimental and finite element analysis of the rat ulnar loading model-correlations between strain and bone formation following fatigue loading

The rat forelimb compression model has been used widely to study bone response to mechanical loading. We used strain gages to assess load sharing between the ulna and radius in the forelimb of adult Fisher rats. We used histology and peripheral quantitative computed tomography (pQCT) to quantify ulnar bone formation 12 days after in vivo fatigue loading. Lastly, we developed a finite element model of the ulna to predict the pattern of surface strains during compression. Our findings indicate that at the mid-shaft the ulna carries 65% of the applied compressive force on the forelimb. We observed large variations in fatigue-induced bone formation over the circumference and length of the ulna. Bone formation was greatest 1-2 mm distal to the mid-shaft. At the mid-shaft, we observed woven bone formation that was greatest medially. Finite element analysis indicated a strain pattern consistent with a compression-bending loading mode, with the greatest strains occurring in compression on the medial surface and lesser tensile strains occurring laterally. A peak strain of -5190 microepsilon (for 13.3N forelimb compression) occurred 1-2 mm distal to the mid-shaft. The pattern of bone formation in the longitudinal direction was highly correlated to the predicted peak compressive axial strains at seven cross-sections (r2 = 0.89, p = 0.014). The in-plane pattern of bone formation was poorly correlated to the predicted magnitude of axial strain at 51 periosteal locations (r2 = 0.21, p < 0.001), because the least bone formation was observed where tensile strains were highest. These findings indicate that the magnitude of bone formation after fatigue loading is greatest in regions of high compressive strain.