Effect of air ions on submicron t1 bacteriophage aerosols

The effect of a high concentration of ionized air molecules on sampling T1 phage aerosols of submicron particle size was evaluated by comparing the phage recoveries of all-glass impingers (AGI-4) and type 6 filter papers. Sampler recoveries of all ionized aerosols were less than the recoveries of nonionized control aerosols. These reductions in recovery were greater with positive ions than with negative ions or ions of mixed polarity. The AGI-4 allowed considerable slippage, which was not affected by the air ions. Type 6 filter paper recoveries were less than AGI-4 recoveries. The air ions did not appear to affect the aerosol particle size as determined by an electron microscope.     

Efficacy of iodine-treated biocidal filter media against bacterial spore aerosols

Aims: To assess the effectiveness of iodine-treated biocidal filter media against bacterial spore aerosols. Methods and Results: Bacillus subtilis spores were aerosolized and introduced into a filtration system. Both treated and untreated filters exhibited high viable removal efficiency (>99·996%) with negligible variation in pressure drop during the entire experiment. The viability of collected spores on the filter was investigated by enumeration of spores extracted from the filter by vortexing. At room temperature and low relative humidity (RH), the survival fraction of the treated filter was significantly lower than that of the untreated filter (P-value < 0·05). Meanwhile, at room temperature and high RH and at high temperature and high RH, the survival fractions on the treated medium were statistically the same as the untreated control at room temperature and low RH. Conclusions: Both treated and untreated filters achieved excellent viable removal efficiency for spores. The pressure drop of the treated filter was not affected by the iodine treatment. The viability of collected bacterial spores was decreased because of the exertion of iodine disinfectant. Significance and Impact of the Study: The evaluation demonstrates that the iodine-treated filter is a viable medium for respiratory protection against infectious spore aerosols. The results warrant further evaluation of smaller biological agents, which exhibit higher penetration.     

Assessment of iodine‐treated filter media for removal and inactivation of MS2 bacteriophage aerosols

Aims: To investigate the performance of an iodine‐releasing filter medium for use as a protective device against airborne pathogens. Methods and Results: The filter’s physical and viable removal efficiencies (VRE) were investigated with challenges of MS2 bacteriophage aerosols, and the infectivity of MS2 collected on the filter was analysed. To test a proposed inactivation mechanism, media containing thiosulfate or bovine serum albumin (BSA) were put in impingers to quench and consume I₂ released from the filter. In direct plating experiments, treated filters presented significantly higher VREs than did untreated filters; however, collection in excess BSA decreased VRE by half and in thiosulfate the apparent VRE decreased drastically. No significant difference in infectivity of retained viruses on treated and untreated filters was observed at the same environmental condition. Conclusions: Evidence presented herein for competition by dissolved I₂ in infectivity assays supports a mechanism of induced displacement and capture of I_2. It also requires that dissociation of iodine from the filter and capture of iodine by MS2 aerosols as they pass through the filter be factored in the design of the assessment methodology. The filter’s strong retention capability minimizes reaerosolization but also makes it difficult to discriminate the antimicrobial effect at the surface. Significance and Impact of the Study: This study shows the direct plating assay method to be sensitive to interference by iodine‐releasing materials. This requires reevaluation of earlier reports of VRE measurements.     

Method for detecting viruses in aerosols

A simple method with poliovirus as the model was developed for recovering human enteric viruses from aerosols. Filterite filters (pore size, 0.45 micron; Filterite Corp., Timonium, Md.) moistened with glycine buffer (pH 3.5) were used for adsorbing the aerosolized virus. No virus passed the filter, even with air flow rates of 100 liters/min. Virus recovery from the filter was achieved by rapid elution with 800 ml of glycine buffer, pH 10. The virus in the primary eluate was reconcentrated by adjusting the pH to 3.5, adding AlCl3 to 0.0005 M, collecting the virus on a 0.25-micron-pore Filerite disk (diameter, 25 mm) and and eluting with 6 ml of buffer, pH 10. With this method, virus could be detected regularly in aerosols produced by flushing when 3 X 10(8) PFU of poliovirus were present in the toilet bowl. Poliovirus-containing fecal material from two of four infants who had recently received oral polio vaccine also yielded virus in the aerosols when feces containing 2.4 X 10(7) to 4.5 X 10(7) PFU of virus had been added to the toilet bowl. Persons infected with a variety of natural enteric viruses are known to excrete this amount of virus in their daily stools.     

Method for detecting viruses in aerosols.

A simple method with poliovirus as the model was developed for recovering human enteric viruses from aerosols. Filterite filters (pore size, 0.45 micron; Filterite Corp., Timonium, Md.) moistened with glycine buffer (pH 3.5) were used for adsorbing the aerosolized virus. No virus passed the filter, even with air flow rates of 100 liters/min. Virus recovery from the filter was achieved by rapid elution with 800 ml of glycine buffer, pH 10. The virus in the primary eluate was reconcentrated by adjusting the pH to 3.5, adding AlCl3 to 0.0005 M, collecting the virus on a 0.25-micron-pore Filerite disk (diameter, 25 mm) and and eluting with 6 ml of buffer, pH 10. With this method, virus could be detected regularly in aerosols produced by flushing when 3 X 10(8) PFU of poliovirus were present in the toilet bowl. Poliovirus-containing fecal material from two of four infants who had recently received oral polio vaccine also yielded virus in the aerosols when feces containing 2.4 X 10(7) to 4.5 X 10(7) PFU of virus had been added to the toilet bowl. Persons infected with a variety of natural enteric viruses are known to excrete this amount of virus in their daily stools.     

Homogeneous Bacterial Aerosols Produced with a Spinning-Disc Generator

Aerosols composed of viable particles of a uniform size were produced with a commercial spinning-disc generator from aqueous suspensions of Bacillus subtilis var. niger spores containing various amounts of an inert material, dextran, to regulate aerosol particle size. Aerosols composed of single naked spores having an equivalent spherical diameter of 0.87 mum were produced from spore suspensions without dextran, whereas aerosols produced from suspensions containing 0.001, 0.01, 0.1, and 1% dextran had median diameters of 0.90, 1.04, 1.80, and 3.62 mum, respectively. Such aerosols, both homogeneous and viable, would be useful for calibrating air sampling devices, evaluating air filter systems, or for employment wherever aerosol behavior may be size-dependent.     

Evaluation of four sampling devices for Burkholderia pseudomallei laboratory aerosol studies

Previous field and laboratory studies investigating airborne Burkholderia pseudomallei have used a variety of different aerosol samplers to detect and quantify concentrations of the bacteria in aerosols. However, the performance of aerosol samplers can vary in their ability to preserve the viability of collected microorganisms, depending on the resistance of the organisms to impaction, desiccation, or other stresses associated with the sampling process. Consequently, sampler selection is critical to maximizing the probability of detecting viable microorganisms in collected air samples in field studies and for accurate determination of aerosol concentrations in laboratory studies. To inform such decisions, the present study assessed the performance of four laboratory aerosol samplers, specifically the all-glass impinger (AGI), gelatin filter, midget impinger, and Mercer cascade impactor, for collecting aerosols containing B. pseudomallei generated from suspensions in two types of culture media. The results suggest that the relative performance of the sampling devices is dependent on the suspension medium utilized for aerosolization. Performance across the four samplers was similar for aerosols generated from suspensions supplemented with 4% glycerol. However, for aerosols generated from suspensions without glycerol, use of the filter sampler or an impactor resulted in significantly lower estimates of the viable aerosol concentration than those obtained with either the AGI or midget impinger. These results demonstrate that sampler selection has the potential to affect estimation of doses in inhalational animal models of melioidosis, as well as the likelihood of detection of viable B. pseudomallei in the environment, and will be useful to inform design of future laboratory and field studies.     

Bacterial communities in aerosols and manure samples from two different dairies in central and Sonoma valleys of California

Aerosols have been suspected to transport food pathogens and contaminate fruits and vegetables grown in close proximity to concentrated animal feeding operations, but studies are lacking that substantiate such transport. To monitor the potential transport of bacteria originated from fresh or dry manure through aerosols on a dairy, we identified by 16S rRNA sequencing, bacteria in aerosols collected within 2 to 3 meters from dairy cows at two dairies. Gram-positive Firmicutes were predominant in aerosols from a dairy in Sonoma, California, and surrounded by vineyards, in contrast to sequences of Gram-negative Proteobacteria predominant in aerosols from a dairy in Modesto, California, also surrounded by other dairies. Although Firmicutes represented approximately 50% of the 10 most abundant sequences, aerosols from the Sonoma dairy also contained sequences of Bacteriodetes and Actinobacteria, identified previously with animal feces. While none of the top 10 sequences from fresh or dry manure from Modesto dairy were detected in aerosols, two of the sequences from the phylum Bacteriodetes and one from class Clostridia from fresh manure were detected in aerosols from Sonoma. Interestingly, none of the sequences from dry manure were in the top 10 sequences in aerosols from both dairies. The 10 most abundant sequences in aerosols from the Modesto dairy were all from Proteobacteria and nearly half of them were from genus Massilia, which have been isolated previously from immune-compromised people and aerosols. We conclude that the predominant bacteria in aerosols are diverse among locations and that they do not reflect the predominant species of bacteria present in cow feces and/or in close proximity to cows. These results suggest that the aerosol sequences did not originate from manure. Large volumes of aerosols would be required to determine if bacterial sequences from aerosols could be used to track bacteria in manure to crops grown in proximity.     

A closed system for the filtration of Mycobacterium bovis liquid cultures using disposable capsule filters

A filtration system was designed to sterilize large volumes of Mycobacterium bovis BCG Tokyo culture safely, needed to purify protein antigens for immunodiagnosis of bovine tuberculosis. A closed system consists of culture bottles connected to three disposable filter capsules of decreasing pore size in series : a depth prefilter over a 1·2 μm filter ; a 0·8 μm prefilter over a 0·45 μm filter ; and a 0·2 μm sterile filter. Low air pressure (3 psi) forces liquid from below the bacillary pellicle. The system features a stainless steel clamp to hold rubber stoppers on the culture bottles, pleated filters to exclude bacillary clumps, a quick disconnector to minimize aerosols, and a closed system with plastic disposable filters that can be autoclaved as a unit without dismantling.     

Sampling Submicron T1 Bacteriophage Aerosols

Liquid impingers, filter papers, and fritted bubblers were partial viable collectors of radioactive submicron T1 bacteriophage aerosols at 30, 55, and 85% relative humidity. Sampler differences for viable collection were due to incomplete physical collection (slippage) and killing of phage by the samplers. Dynamic aerosols of a mass median diameter of 0.2 mu were produced with a Dautrebande generator from concentrated aqueous purified phage suspensions containing extracellular soluble radioactive phosphate as a physical tracer. There was considerable destruction of phage by the Dautrebande generator; phage titers of the Dautrebande suspension decreased exponentially, but there was a progressive (linear) increase in tracer titers. Liquid impingers recovered the most viable phage but allowed considerable (30 to 48%) slippage, which varies inversely with the aerosol relative humidity. Filter papers were virtually complete physical collectors of submicron particles but were the most destructive. Fritted bubbler slippage was more than 80%. With all samplers, phage kill was highest at 85% relative humidity and lowest at 55% relative humidity. An electrostatic precipitator was used to collect aerosol samples for particle sizing with an electron microscope. The particle size was slightly larger at 85% relative humidity than at 30 or 55% relative humidity.     

Release of radioactive aerosols from the object "shelter" during strong winds

Results of measurements of radionuclide and disperse compositions of aerosols in ventilation system "Bypass" of the object "Shelter" of the Chernobyl NPP are presented. The Bypass is used for releasing contaminated air from the destroyed reactor of Block-IV to the atmosphere. In aerosols, the experimentally found ratio of 137Cs concentration to the sum of beta-emitting radionuclides more than 1.5 times exceeds the calculated ratio for nuclear fuel (in December, 2003). Using the data of meteorological station "Chornobyl", which situated 15 km SE from the Chernobyl NPP, we found that the wind with mean velocity of 4-5 m/sec or more and gusts of 10-11 m/sec led to increasing the aerosol concentration in the Bypass by more than power of magnitude. With the help of filter pack technique sizes of aerosol particles--the carriers of Chernobyl's radioactivity--were measured. It was found that the range of activity median aerodynamical diameter (AMAD) is 2-5 microns.     

Gas-phase removal of biofilms from various surfaces using carbon dioxide aerosols

The present study evaluated the removal of Escherichia coli XL1-blue biofilms using periodic jets of carbon dioxide aerosols (a mixture of solid and gaseous CO(2)) with nitrogen gas. The aerosols were generated by the adiabatic expansion of high-pressure CO(2) gas through a nozzle and used to remove air-dried biofilms. The areas of the biofilms were measured from scanning electron micrographs before and after applying the aerosols. The removal efficiency of the aerosol treatment was measured with various air-drying times of the biofilms before the treatment, surface materials, and durations of CO(2) aerosols in each 8-s aerosol-nitrogen cleaning cycle. Nearly 100% of the fresh biofilms were removed from the various surfaces very reliably within 90?s. This technique can be useful for removing unsaturated biofilms on solid surfaces and has potential applications for cleaning bio-contaminated surfaces.     

Microbial aerosol generation during laboratory accidents and subsequent risk assessment

AIM: To quantify microbial aerosols generated by a series of laboratory accidents and to use these data in risk assessment. METHODS AND RESULTS: A series of laboratory accident scenarios have been devised and the microbial aerosol generated by them has been measured using a range of microbial air samplers. The accident scenarios generating the highest aerosol concentrations were, dropping a fungal plate, dropping a large bottle, centrifuge rotor leaks and a blocked syringe filter. Many of these accidents generated low particle size aerosols, which would be inhaled into the lungs of any exposed laboratory staff. Spray factors (SFs) have been calculated using the results of these experiments as an indicator of the potential for accidents to generate microbial aerosols. Model risk assessments have been described using the SF data. CONCLUSIONS: Quantitative risk assessment of laboratory accidents can provide data that can aid the design of containment laboratories and the response to laboratory accidents. SIGNIFICANCE AND IMPACT OF THE STUDY: A methodology has been described and supporting data provided to allow microbiological safety officers to carry out quantitative risk assessment of laboratory accidents.     

Survival of microorganisms on antimicrobial filters and the removal efficiency of bioaerosols in an environmental chamber

Exposure to bioaerosols causes various adverse health effects including infectious and respiratory diseases, and hypersensitivity. Controlling exposure to bioaerosols is important for disease control and prevention. In this study, we evaluated the efficacies of various functional filters coated with antimicrobial chemicals in deactivating representative microorganisms on filters or as bioaerosols. Tested functional filters were coated with different chemicals that included (i) Ginkgo and sumac, (ii) Ag-apatite and guanidine phosphate, (iii) SiO2, ZnO, and Al2O3, and (iv) zeolite. To evaluate the filters, we used a model ventilation system (1) to evaluate the removal efficiency of bacteria (Escherichia coli and Legionella pneumophila), bacterial spores (Bacillus subtilis spore), and viruses (MS2 bacteriophage) on various functional filters, and (2) to characterize the removal efficiency of these bioaerosols. All experiments were performed at a constant temperature of 25 degrees C and humidity of 50%. Most bacteria (excluding B. subtilis) rapidly decreased on the functional filter. Therefore, we confirmed that functional filters have antimicrobial effects. Additionally, we evaluated the removal efficiency of various bioaerosols by these filters. We used a six-jet collision nebulizer to generate microbial aerosols and introduced it into the environmental chamber. We then measured the removal efficiency of functional filters with and without a medium-efficiency filter. Most bioaerosol concentrations did not significantly decrease by the functional filter only but decreased by a combination of functional and medium-efficiency filter. In conclusion, functional filters could facilitate biological removal of various bioaerosols, but physical removal of these by functional was minimal. Proper use of chemical-coated filter materials could reduce exposure to these agents.     

Fluorometric Method for Determining the Efficiency of Spun-Glass Air Filtration Media

The procedures and equipment needed to measure filtration efficiency by means of fluorescent aerosols are described. The filtration efficiency of individual lots of spun-glass air filtration medium or of entire air filtration systems employing such media was determined. Data relating to the comparative evaluation of spun-glass filter media by means of the fluorometric method described, as well as by conventional biological procedures, are presented.     

Gas-phase removal of biofilms from various surfaces using carbon dioxide aerosols

The present study evaluated the removal of Escherichia coli XL1-blue biofilms using periodic jets of carbon dioxide aerosols (a mixture of solid and gaseous CO₂) with nitrogen gas. The aerosols were generated by the adiabatic expansion of high-pressure CO₂ gas through a nozzle and used to remove air-dried biofilms. The areas of the biofilms were measured from scanning electron micrographs before and after applying the aerosols. The removal efficiency of the aerosol treatment was measured with various air-drying times of the biofilms before the treatment, surface materials, and durations of CO₂ aerosols in each 8-s aerosol–nitrogen cleaning cycle. Nearly 100% of the fresh biofilms were removed from the various surfaces very reliably within 90 s. This technique can be useful for removing unsaturated biofilms on solid surfaces and has potential applications for cleaning bio-contaminated surfaces.     

生物安全三级实验室核心区排风高效空气过滤器原位消毒的研究

<实验室生物安全通用要求>(GB19489-2008)要求生物安全三级实验室"应可以在原位对排风高效空气(HEPA)过滤器进行消毒灭菌".BSL-3实验室核心区排风HEPA过滤器是保证实验操作过程中产生的感染性气溶胶不外泄的最后防线,为了保障环境安全,需在原位实现HEPA过滤器的消毒.本研究设计并制作了循环消毒样机,与排风HEPA过滤器排风箱体的消毒接口连接,利用循环气流带动甲醛蒸汽循环实现原位消毒.结果显示,室温条件下甲醛蒸汽浓度16 mg/L,相对湿度70%,持续熏蒸循环穿透运行12 h,布置于HEPA过滤器排风箱体内用于指示消毒效果的金黄色葡萄球菌、耻垢分枝杆菌、枯草芽胞杆菌及嗜热脂肪芽胞杆菌均被完全杀灭,从设备及方法学两方面实现了排风HEPA过滤器的原位消毒.     

Effect of Relative Humidity on Dynamic Aerosols of Adenovirus 12

Dynamic aerosols of adenovirus 12 were generated in the same Henderson apparatus under conditions of high, medium, and low relative humidity. High relative humidities resulted in more recovery of adenovirus 12 from aerosols and lungs of newborn Syrian hamsters. At 89, 51, and 32% relative humidity, the total infectious virus recovered from a 20-min aerosol was 10(6.7), 10(6.0), and 10(4.3) TCD(50), respectively. Hamsters exposed to these 20-min aerosols retained measured lung doses of 10(3.0), 10(2.4), and 10(1.0) TCD(50), respectively. The measured retained lung doses were compared to calculated inhaled lung doses based on both total virus aerosolized and total virus recovery from the aerosols.     

Vapors Produced by Electronic Cigarettes and E-Juices with Flavorings Induce Toxicity,Oxidative Stress,and Inflammatory Response in Lung Epithelial Cells and in Mouse Lung

Oxidative stress and inflammatory response are the key events in the pathogenesis of chronic airway diseases. The consumption of electronic cigarettes (e-cigs) with a variety of e-liquids/e-juices is alarmingly increasing without the unrealized potential harmful health effects. We hypothesized that electronic nicotine delivery systems (ENDS)/e-cigs pose health concerns due to oxidative toxicity and inflammatory response in lung cells exposed to their aerosols. The aerosols produced by vaporizing ENDS e-liquids exhibit oxidant reactivity suggesting oxidants or reactive oxygen species (OX/ROS) may be inhaled directly into the lung during a “vaping” session. These OX/ROS are generated through activation of the heating element which is affected by heating element status (new versus used), and occurs during the process of e-liquid vaporization. Unvaporized e-liquids were oxidative in a manner dependent on flavor additives, while flavors containing sweet or fruit flavors were stronger oxidizers than tobacco flavors. In light of OX/ROS generated in ENDS e-liquids and aerosols, the effects of ENDS aerosols on tissues and cells of the lung were measured. Exposure of human airway epithelial cells (H292) in an air-liquid interface to ENDS aerosols from a popular device resulted in increased secretion of inflammatory cytokines, such as IL-6 and IL-8. Furthermore, human lung fibroblasts exhibited stress and morphological change in response to treatment with ENDS/e-liquids. These cells also secrete increased IL-8 in response to a cinnamon flavored e-liquid and are susceptible to loss of cell viability by ENDS e-liquids. Finally, exposure of wild type C57BL/6J mice to aerosols produced from a popular e-cig increase pro-inflammatory cytokines and diminished lung glutathione levels which are critical in maintaining cellular redox balance. Thus, exposure to e-cig aerosols/juices incurs measurable oxidative and inflammatory responses in lung cells and tissues that could lead to unrealized health consequences.     

INAA and PIXE of Atmospheric and Combustion Aerosols

Using instrumental neutron activation analyses and photoninduced x-ray emission techniques for analysis of size-fractionated atmospheric and combustion aerosols and other emission samples arising from fluidized-bed combustion of North Bohemian lignites up to 42 elements were determined in all sample types. This allowed the evaluation of element enrichment, time trends, and interelement correlations and the performance of factor analysis of various fractions of atmospheric aerosols. The data obtained on mass and element size distributions of aerosols and emission samples obtained upon lignite combustion in an experimental scale atmospheric fluidized-bed combustor without and with added hydrated lime and limestone were used to elucidate the mechanism of abatement of toxic trace and matrix elements from flue gas.