AB-8大孔树脂吸附分离红花桑寄生总黄酮的影响因子研究

AB-8大孔吸附树脂对红花桑寄生总黄酮静态吸附和动态洗脱的效果,受提取液质量浓度、pH值及环境温度、振速以及洗脱剂乙醇浓度、流速等因素影响。试验表明,提取液质量浓度和pH值对AB-8树脂的吸附效果有显著影响,其吸附分离总黄酮的工艺条件为:浓度为1.2~2.0 mg/ml、pH 3.0~4.0的红花桑寄生提取液,置于摇床上,于室温条件下振荡(振速160 r/min)吸附2~3 h,然后用5倍于树脂体积(5BV)的50%乙醇以1.5 ml/min流速进行柱上动态解吸。AB-8树脂对红花桑寄生总黄酮的饱和吸附量可达29.0 mg/g,动态洗脱率达95.0%,获得产品中黄酮纯度为46.0%,得率为5.5%。     

青霉素酰化酶在新型复合载体上的固定化研究

通过γ-氯丙基三甲氧基硅烷的媒介,将聚乙烯亚胺(PEI)化学偶联在硅胶微粒表面,制备了新型复合载体PEI/silica gel,然后通过双官能团试剂戊二醛的作用,将青霉素酰化酶固定在复合载体上;考察了戊二醛用量、pH值、固定化温度、固定化时间及给酶量等条件对固定化青霉素酰化酶表观活力、活性回收率等性能的影响;并通过测定复合载体在固定化前的ζ电位,探索了复合载体PEI/silica gel固定化酶的作用机理。研究结果表明,由于PEI分子链中含有大量胺基,共价键联与物理吸附相结合,使青霉素酰化酶被快速稳定地固定化,并具有高的催化活性与活力回收率。复合载体PEI/silica gel(0.5 g)固定青霉素酰化酶的适宜固定化条件为:固定化温度为30℃;固定化时间为14~15 h;戊二醛用量为1.2 mmol/g;pH=7.92;给酶量为0.1 mL/g。     

D-泛解酸内酯水解酶的固定化及酶学性质

为有效提高D-泛解酸内酯水解酶的利用效率,笔者选择合适的载体对酶进行固定化,在优化固定化条件的同时研究固定化酶的最佳反应条件和酶学性质。结果表明,选择的最佳固定化载体为树脂D380,最佳固定化条件为:酶的吸附添加量为30 U(以1 g湿树脂计),吸附pH 7.0,吸附温度30℃,吸附时间5 h,戊二醛体积分数0.1%,交联时间1 h。在最优条件下得到的固定化酶的比酶活为(11.5±0.12) U/g。固定化酶的最适反应温度为37℃,最适反应pH为7.5。游离酶和固定化酶的动力学常数K_m分别为170.25和207.60 mmol/L。Ca~(2+)对酶促反应有激活作用,Mn~(2+)对该酶有较强的抑制作用。     

大孔吸附树脂吸附链霉菌702抗真菌活性物质工艺

研究大孔吸附树脂吸附链霉菌702抗真菌活性物质的工艺条件。采用5种不同大孔吸附树脂吸附链霉菌702发酵液提取液中抗真菌活性物质,选择吸附效果较佳树脂进行吸附条件优化,以桔青霉为指示菌,纳他霉素为对照抗生素．采用“管碟法”测定抗真菌活性物质含量。结果发现,XAD18树脂吸附效果较好,获得优化吸附条件：上样液pH6,NaCl质量浓度10g/L,上样量22．63mg／g湿树脂,吸附流速2．5mL／min,水洗体积180mL,洗脱流速1．5mL／min,洗脱剂为体积分数10％、50％和90％的甲醇,洗脱方式为梯度洗脱。在确定的工艺条件下XAD18对链霉菌702抗真菌活性物质的吸附率可达90％,洗脱率可达75％,回收率可达80％。     

海泡石吸附固定化猪胰脂肪酶

以海泡石作为猪胰脂肪酶(PPL)的固定化载体,考察采用物理吸附的方法制备固定化脂肪酶的条件。结果表明:在固载时间4 h、反应磷酸盐(PBS)溶液pH 6.0、反应温度25℃时,可达最大比酶活309 U/g,固定化酶的化学稳定性和热稳定性均较高。同时利用红外谱仪(FT-IR)和扫描电子显微镜(SEM)的分析手段对固定化猪胰脂肪酶试样进行分析,进一步确定了海泡石材料在固定化酶中的作用。     

大孔树脂用于菊苣菊粉的脱色研究

运用静态吸附试验对8种大孔树脂进行筛选,通过单因素试验、正交试验和方差分析确定了菊苣菊粉脱色的最佳操作条件.结果表明,LSD-263树脂对菊苣菊粉色素的吸附性能较好;最佳脱色条件为:上柱温度45℃,色素浓度(以吸光度计)0.773 Abs,上柱速度3 BV/h.在此条件下,LSD-263树脂对色素的吸附量可达14.48△AV/mL,菊粉损失率仅为2.38%.     

细叶十大功劳叶中总生物碱大孔树脂纯化及抗氧化研究

为确定细叶十大功劳(Mahonia fortunei)叶中总生物碱大孔树脂分离纯化的最佳工艺条件及抗氧化活性，该研究通过比较6种大孔吸附树脂对总生物碱的静态吸附和解吸附效果，优选出最佳树脂并考察其动态纯化总生物碱的工艺条件，并采用DPPH法对纯化前后的总生物碱抗氧化性能进行评价。结果表明：(1)AB-8型大孔吸附树脂纯化效果最好，其最佳工艺条件为上样浓度50 mg·mL^-1(生药浓度)、上样量26 BV、上样液流速2 BV·h^-1;吸附完成后，以3 BV水洗后再以4 BV 50%乙醇洗脱，在此条件下得到的总生物碱含量由13.33%提高到56.64%。(2)各样品对DPPH自由基的清除能力为对照品Vc(IC₅₀=10.39μg·mL^-1)>总生物碱纯化品(IC₅₀=39.08μg·mL^-1)>总生物碱粗品(IC₅₀=55.28μg·mL^-1)。综上表明，AB-8型大孔吸附树脂可有效富集细叶十大功劳叶中总...     

固定化葡萄糖异构酶最适pH值的调节

用多孔强碱性三乙醇胺基聚苯乙烯树脂作为载体,用CNBr与载体上多羟基作用共价偶联葡萄糖异构酶(GI)。最适偶联条件表明:CNBr量增多,蛋白载量增加,但比活下降。固定化葡萄糖异构酶(IGI)最适反应温度比天然酶提高15℃。并系统地研究了影响IGI活力-pH的曲线的各种因素:用具有不同平均孔径的载体(R=137A,185A,230A,365A)固定化GI,在低离子强度条件下(0.0064mol/L),测定其最适pH值分别7.76,7.56,7.50,8.20。选择平均孔径为230A且具有不同数量三乙醇胺基的载体(0.94,1.05,1.13,1.37mmol/g干胶)分别固定化GI,其最适pH值分别为7.70,7.50,7.46,7.36。     

新型固定化酶载体——球状纤维素单宁树脂的研制

以球状纤维素为基体,通过醇化和胺化反应,成功地制备出一种新型的固定化酶载体──球状纤维素单宁树脂．该树脂具有良好的水力学性能,化学稳定性高,对蛋白质和酶等大分子有较高的吸附容量,并且对酶吸附牢固,是一种良好的酶固定化载体。作者对合成条件进行了正交优化,并初步探讨了该树脂对酶的吸附特性。     

黑果枸杞色素的提取和精制工艺研究

本文采用正交实验法对黑果枸杞色素的提取和精制工艺进行了研究。结果表明,黑果枸杞色素的最佳提取条件为:以pH 3.0的80%乙醇作浸提剂,提取温度50℃,提取时间3 h,固液配比1:40;用X-5大孔吸附树脂对色素进行精制,以树脂柱径高比1:15、流速3 mL/minp、H 3.0、色素液浓度1 g/L为最佳吸附条件,色素的吸附量可达0.03715 g/mL湿树脂体积;而以95%乙醇做洗脱液,在pH 2.0、流速5 mL/min、3倍于柱床体积的洗脱液条件下解吸附效果最佳,色素回收率达到97.78%;制取的色素产品外观呈紫红色,色价为36.7。     

Reversible immobilization of glucoamylase onto magnetic polystyrene beads with multifunctional groups

A novel and simple process for the surface functionalization of micron-sized monodisperse magnetic polystyrene (PS) microbeads was reported. The polystyrene seed particles were prepared prior to the dispersion polymerization method. Afterwards, series of surface chemical modifications on polystyrene microspheres were conducted, and three end-functional microspheres with carboxyl, imidazolyl and sulphydryl groups were obtained. The functional magnetic polystyrene microspheres were prepared by impregnation and subsequent precipitation of ferric and ferrous ions into the polystyrene particles. Finally, the functional magnetic polystyrene was used for the reversible immobilization of glucoamylase via metal-affinity adsorption. The results indicated that the obtained immobilized glucoamylase presented excellent reusability, applicability, magnetic response and regeneration of supports. The magnetic PS microspheres retained >65% of its initial activity at 65 °C over 6 h; and the lowest residual activity of immobilized glucoamylase prepared by regenerated supports still remained about 50% of the initial activity after the 10th cycles.     

Optical and structural properties of composites films based on Ce3+-doped yttrium aluminium garnet nanoparticles embedded in polystyrene

In the present work, attempts have been made to prepare scintillating nanoparticle composite films of Ce³⁺-doped Y₃Al₅O₁₂ (YAG:Ce) embedded in a polystyrene (PS) polymer. A YAG:Ce phosphor has been previously synthesized using the sol–gel method. YAG:Ce-PS composite films of 250 ± 30 μm thickness were prepared using a solvent casting procedure with different PS/solvent concentration and a different mass ratio between nanoparticles of YAG:Ce and PS. X-ray diffraction analysis confirmed that the YAG:Ce powders were successfully prepared. Using thermogravimetric analyses and differential scanning calorimetry, we found that the glass transition temperature (Tg) and thermal degradation were shifted to higher temperatures for composite films relative to pure PS. Photoluminescence showed the yellow emission of the Ce³⁺-doped YAG phosphors, which was attributed to the 5d→4f transition of Ce³⁺ ion and the intensity of the emissions changed with the mass ratio of the YAG:Ce nanoparticles incorporated in the polymer and with the concentration of the polymer solution.     

The Study of Impedance and Conductivity of New Modified Polystyrene Used as an Effective Adsorbent of Ba(II) Ions

In the research described here we prepared a novel, modified polystyrene (PS) with iminoether as the complexing agent for Ba²⁺. Most heavy metals cause environmental, atmospheric pollution.^[1–2] They cause consequence for humans health and aquatic life due to their toxicity. They become strongly toxic by mixing with different environmental elements and their removal from contaminated water is very important. The structure of all modified polystyrene such as nitrated polystyrene (PS−NO₂), aminated polystyrene (PS−NH₂), aminated polystyrene with imidate group (PS−NH−Im) and the complex with barium metal (PS−NH−Im/Ba²⁺) were analyzed by Fourier transform infrared spectroscopy (FT-IR), and the formation of N-2-Benzimidazolyl iminoether grafted PS was proved. The thermal stability and structure of the polystyrene and modified polystyrene were studied by differential thermal analysis (DTA) and X-ray diffractometry (XRD), respectively. The elemental analysis was used for the determination of the chemical composition of the modified PS. The grafted polystyrene was used in order to adsorb barium from wastewater with an acceptable cost before the wastewater distribution in the environment. The impedance analysis of the polystyrene complex PS−NH−Im/Ba²⁺ indicated an activated thermal conduction mechanism.The conductivity analysis of the complex with barium metal PS−NH−Im/Ba²⁺ was studied; the activation energy was deduced from an Arrhenius plot and corresponded to, , suggesting PS−NH−Im/Ba²⁺ was a proton-type of semiconductor.     

Effective separation of peptides using highly dense thermo-responsive polymer brush-grafted porous polystyrene beads

For the development of well-defined highly dense thermo-responsive polymer grafted surface as an improved stationary phase for thermo-responsive chromatography, poly(N-isopropylacrylamide) (PIPAAm) brush-grafted porous polystyrene beads were prepared by surface-initiated atom transfer radical polymerization (ATRP). The PIPAAm grafted region of polystyrene beads was adjusted by the addition of isooctane as a poor solvent for polystyrene upon the reaction of ATRP initiator immobilization. Using a thermo-responsive HPLC column containing the prepared beads with PIPAAm brush grafted on the inside pores nearby the outer surfaces, angiotensin subtypes were effectively separated with aqueous mobile phase, because the densely grafted PIPAAm on nearby the outer surface effectively interacted with the peptides hydrophobically. Retention of basic peptide was achieved by the beads with basic mobile phase. These results indicated that the prepared beads with grafted PIPAAm nearby the outer surface became an effective chromatographic stationary phase for retaining basic peptides using wide pH range of mobile phase.     

Solvent-responsiveness of PS–PEO binary mixed polymer brushes: a coarse-grained molecular dynamics study

Abstract

Systems of mixed polymer brushes (polystyrene–polyethylene oxide, PS–PEO) uniformly grafted on solid substrate were investigated by coarse-grained molecular dynamics simulations. The effects of grafting density and relatively degree of polymerisation of PS and PEO on the switching property of PS–PEO mixed polymer brushes in water and solvent are explored and discussed. Simulation results indicate that PS dominated the thickness of PS–PEO mixed polymer brushes in different solvents, which can be controlled by adjusting the grafting density. Brush heights of mixed PS–PEO polymer brushes fluctuate in different solvents when grafting density varies. The chemical composition of the very top surface of these mixed polymer brushes are largely determined by the relative polymerisation degree of PS and PEO.     

Enhancing the "stickiness" of bile acids to cross-linked polymers: a bioconjugate approach to the design of bile acid sequestrants

A series of cross-linked polymers have been synthesized by reaction of 2% cross-linked, chloromethylated polystyrene with a tertiary amine derivative (7) of cholic acid (prepared by reaction of cholic acid methyl ester with N,N-dimethyl-ethylenediamine), followed by exhaustive quaternization with trimethylamine. Increased loadings of 7 result in enhanced binding of taurocholate ion and a decrease in its rate of release upon exposure to 50 mM aqueous NaCl. Examination of particle-size effects indicates that film diffusion and particle diffusion both contribute to the observed kinetics. Interruption tests that were carried out confirmed that particle diffusion is kinetically important. The relevance of this bioconjugate approach to the design of bile acid sequestrants for the treatment of hypercholesterolemia is briefly discussed.     

Voltammetric studies of hemoglobin-coated polystyrene latex bead films on pyrolytic graphite electrodes

A novel hemoglobin (Hb)-coated polystyrene (PS) latex bead film was deposited on pyrolytic graphite (PG) electrode surface. In the first step, positively charged Hb molecules in pH 5.0 buffers were adsorbed on the surface of negatively charged, 500 nm diameter PS latex beads bearing sulfate groups by electrostatic interaction. The aqueous dispersion of Hb-coated PS particles was then deposited on the surface of PG electrodes and, after evaporation of the solvent, Hb-PS films were formed. The Hb-PS film electrodes exhibited a pair of well-defined, quasi-reversible cyclic voltammetric (CV) peaks at about −0.36 V vs. SCE in pH 7.0 buffers, characteristic of Hb heme Fe(III)/Fe(II) redox couples. Positions of Soret absorption band of Hb-PS films suggest that Hb retains its near-native structure in the films in its dry form and in solution at medium pH. The Hb in PS films was also acted as a catalyst to catalyze electrochemical reduction of various substrates such as trichloroacetic acid (TCA), nitrite, oxygen and hydrogen peroxide.     

Synergistic Impact of Solvent and Polymer Additives on the Film Formation of Small Molecule Blend Films for Bulk Heterojunction Solar Cells

The addition of polystyrene (PS), a typical insulator, is empirically shown to increase the power conversion efficiencies (PCEs) of a solution‐deposited bulk heterojunction (BHJ) molecular blend film used in solar cell fabrication: p‐DTS(FBTTh₂)₂/PC₇₁BM. The performance is further improved by small quantities of diiodooctane (DIO), an established solvent additive. In this study, how the addition of PS and DIO affects the film formation of this bulk heterojunction blend film are probed via in situ monitoring of absorbance, thickness, and crystallinity. PS and DIO additives are shown to promote donor crystallite formation on different time scales and through different mechanisms. PS‐containing films retain chlorobenzene solvent, extending evaporation time and promoting phase separation earlier in the casting process. This extended time is insufficient to attain the morphology for optimal PCE results before the film sets. Here is where the presence of DIO comes into play: its low vapor pressure further extends the time scale of film evolution and allows for crystalline rearrangement of the donor phase long after casting, ultimately leading to the best BHJ organization.     

Morphology control in co-continuous poly(L-lactide)/polystyrene blends: a route towards highly structured and interconnected porosity in poly(L-lactide) materials

Poly(L-lactide) is a biodegradable polymer primarily used in biomedical applications. In this paper, both the microstructure and the region of dual-phase continuity are examined for binary and compatibilized poly(L-lactide)/polystyrene blends (PLLA/PS) prepared by melt mixing. The blends are shown to be completely immiscible with an interfacial tension of 6.1 mN/m. The PS-b-PLLA (24,000-b-28,000) diblock copolymer compatibilizer has an asymmetric effect on the blend. It is effective at compatibilizing 50/50 PLLA/PS blends but is only a marginal emulsifier for blends where PLLA is the dominant matrix. Percent continuity, as estimated by solvent extraction/gravimetry and also torque/composition diagrams clearly indicate an onset of the region of dual-phase continuity at 40-45%PS. It is demonstrated that highly percolated blends of the above materials exist from 40 to 75% PS and 40 to 60% PS for the binary and compatibilized blends, respectively. The scale of the microstructure of the continuous morphology is measured using BET and mercury intrusion porosimetry techniques, after extraction of the PS phase. Both the pore size and extent of continuity can be controlled through composition and interfacial modification. Static annealing of the blend after melt mixing can also be used to substantially increase the pore size of the system. Extraction of the PS phase in the blend, carried out after the above preparation protocols, is a route to generating completely interconnected porosity of highly controlled morphologies (pore size, void volume) in poly(L-lactide) materials. In this study, the pore diameter was controlled from 0.9 to 72 microm for a constant void volume of 45-47%, and the void volume was modified from 35 to 74% depending on the blend composition.     

The preparation of CdTe nanoparticles and CdTe nanoparticle-labelled microspheres for biological applications.

Different sizes of CdTe semiconductor nanoparticles were prepared in aqueous solution. These nanoparticles exhibit narrow fluorescence with full width at half-maximum (FWHM) of 35-45 nm that spans the visible spectrum, and they also have high PL quantum yield with high resistance to photodegradation. In addition, CdTe quantum dot (QD)-labelled microspheres, comprising polystyrene (PS) cores and CdTe/polyelectrolyte (PE) shells, were also prepared by the layer-by-layer technique in this paper. The optical properties of the CdTe nanoparticles and CdTe-labelled microspheres were investigated by UV-Visible absorption and luminescence spectroscopy, and fluorescence microscopy was employed for microscopic identification behaviour of the luminescent microspheres.