Influence of Surface Chemistry on the Hygienic Status of Industrial Stainless Steel

Coupons of fourteen different stainless steels were investigated in terms of surface chemistry and ease of cleaning. Steel surfaces were exposed to Bacillus cereus spores in static saline solution for 2?h. Surfaces were rinsed and then covered with whole milk and allowed to dry. Surfaces were then cleaned in an experimental flow system that mimics an industrial application. After cleaning, remaining spores were released by sonication, spores cultured and colony forming units determined. Surfaces with higher levels of Fe in the outer surface of the passive film cleaned more easily. There was a relation between the polar component and ease of cleaning. The higher the polar component the more easily the surface cleaned. The cleaning mechanism involves dissolution of Fe enriched hydroxide films on the surface.     

Physico-chemical and hygienic property modifications of stainless steel surfaces induced by conditioning with food and detergent

The effect of repeated conditioning procedures (25 runs), consisting of soiling (milk and meat products) and cleaning steps, on the hygienic status, physico-chemical properties and surface chemical composition of stainless steel (SS) surfaces, was investigated. Five SSs differing in grade and finish were used. Both soiling and surface cleaning/conditioning procedures resulted in a similar increase in the surface contamination with carbon, while the changes in the basic component of the surface free energy depended on the conditioning procedure. The passive film was also affected, the Fe/Cr ratio in particular. The hygienic status was also changed, especially with milk as shown by monitoring the number of residual adhering Bacillus cereus spores after contaminating the surface with spores followed by cleaning. The results show that in food environments, the presence and the nature of conditioning molecules play a major role in the hygienic status of SS surfaces.     

Physico-chemical and hygienic property modifications of stainless steel surfaces induced by conditioning with food and detergent

The effect of repeated conditioning procedures (25 runs), consisting of soiling (milk and meat products) and cleaning steps, on the hygienic status, physico-chemical properties and surface chemical composition of stainless steel (SS) surfaces, was investigated. Five SSs differing in grade and finish were used. Both soiling and surface cleaning/conditioning procedures resulted in a similar increase in the surface contamination with carbon, while the changes in the basic component of the surface free energy depended on the conditioning procedure. The passive film was also affected, the Fe/Cr ratio in particular. The hygienic status was also changed, especially with milk as shown by monitoring the number of residual adhering Bacillus cereus spores after contaminating the surface with spores followed by cleaning. The results show that in food environments, the presence and the nature of conditioning molecules play a major role in the hygienic status of SS surfaces.     

Analysis of Kudoa thyrsites (Myxozoa: Myxosporea) spore antigens using monoclonal antibodies.

A method employing Percoll gradient centrifugation was developed to purify Kudoa thyrsites spores from somatic muscle tissue of Atlantic salmon Salmo salar. Highly purified spores were then used to immunize inbred BALB/c mice for derivation of hybridomas secreting Kudoa-specific monoclonal antibodies (mAbs). Analysis of mAbs by immunofluorescence microscopy and flow cytometry showed that several were specific for antigens on the surface of K. thyrsites spores whereas other mAbs reacted with polar capsules or with polar filaments of spores of K. thyrsites, K. paniformis and K. crumena. Immunoblots on spore lysates using the surface-binding mAbs showed a broad band of 46 to > 220 kDa, whereas mAbs specific for antigens of polar capsules and polar filaments detected sharper bands of various molecular masses, depending on the Kudoa species. The dominant epitope of the K. thyrsites spore surface antigen was shown to be carbohydrate as determined by its sensitivity to treatment with anhydrous trifluoromethane sulfonic acid and by its resistance to treatment with Proteinase K. Immunofluorescence microscopy using the K. thyrsites-specific mAbs on isolated, intact, permeabilized plasmodia and on thin sections of somatic muscle tissue containing plasmodia revealed intense labeling of spores both within the spore-producing plasmodia and in the flesh of infected Atlantic salmon. As few as 100 spores were detected by immunoblotting, indicating that these mAbs have potential for use in developing a field-based diagnostic test.     

Influence of transition metals added during sporulation on heat resistance of Clostridium botulinum 113B spores.

Sporulation of Clostridium botulinum 113B in a complex medium supplemented with certain transition metals (Fe, Mn, Cu, or Zn) at 0.01 to 1.0 mM gave spores that were increased two to sevenfold in their contents of the added metals. The contents of calcium, magnesium, and other metals in the purified spores were relatively unchanged. Inclusion of sodium citrate (3 g/liter) in the medium enhanced metal accumulation and gave consistency in the transition metal contents of independent spore crops. In citrate-supplemented media, C. botulinum formed spores with very high contents of Zn (approximately 1% of the dry weight). Spores containing an increased content of Fe (0.1 to 0.2%) were more susceptible to thermal killing than were native spores or spores containing increased Zn or Mn. The spores formed with added Fe or Cu also appeared less able to repair heat-induced injuries than the spores with added Mn or Zn. Fe-increased spores appeared to germinate and outgrow at a higher frequency than did native and Mn-increased spores. This study shows that C. botulinum spores can be sensitized to increased thermal destruction by incorporation of Fe in the spores.     

Influence of transition metals added during sporulation on heat resistance of Clostridium botulinum 113B spores

Sporulation of Clostridium botulinum 113B in a complex medium supplemented with certain transition metals (Fe, Mn, Cu, or Zn) at 0.01 to 1.0 mM gave spores that were increased two to sevenfold in their contents of the added metals. The contents of calcium, magnesium, and other metals in the purified spores were relatively unchanged. Inclusion of sodium citrate (3 g/liter) in the medium enhanced metal accumulation and gave consistency in the transition metal contents of independent spore crops. In citrate-supplemented media, C. botulinum formed spores with very high contents of Zn (approximately 1% of the dry weight). Spores containing an increased content of Fe (0.1 to 0.2%) were more susceptible to thermal killing than were native spores or spores containing increased Zn or Mn. The spores formed with added Fe or Cu also appeared less able to repair heat-induced injuries than the spores with added Mn or Zn. Fe-increased spores appeared to germinate and outgrow at a higher frequency than did native and Mn-increased spores. This study shows that C. botulinum spores can be sensitized to increased thermal destruction by incorporation of Fe in the spores.     

Seed cleaning behavior by tropical ants and its anti-fungal effect

In tropical forests, ants frequently consume fruit pulp around seeds of vertebrate-dispersed plants, which protects the seeds from infection by fungus and pathogens. Seed cleaning behavior by omnivorous ants was observed in the secondary forests of Bogor botanical garden in West Java. Fruit pulp around the seeds of the rambutan Nephelium lappaceum was completely removed by Pheidole plagiaria, Anoplolepis gracilipes, and other ants. When seed cleaners were excluded, however, many seeds were attacked by fungus and died. Seeds that were cleaned by hand, but not by ants, were similarly attacked. Field experiments on seed cleaning by P. plagiaria revealed that the anti-fungal effect was not merely caused by removal of fruit pulp, and that seed cleaning reduced the development of spores and hypha of fungi. We suggest that the workers apply anti-fungal substances to the fruit pulp and seed surface.     

Density changes of Phycomyces spores after reversible and irreversible activation

Spores harvested by conventional methods could be cleaned up considerably using discontinuous density gradients. This method yielded a population of almost entirely viable spores. Germination of the spores resulted in density changes probably due to spore swelling. These changes could be observed as early as 15 min after activation. The usefulness of this method in the study of spore activation was shown by its application to spores germinating after a heat treatment at various temperatures, or to spore reacquiring dormancy by incubation in water after activation at different temperatures. Dormant and activated spores can quickly and easily be separated from mixed populations.     

Cleanability in relation to bacterial retention on unused and abraded domestic sink materials

The relative cleanability of stainless steel, enamelled steel, mineral resin and polycarbonate domestic sink materials was assessed by comparing the number of organisms remaining on surfaces after cleaning. In unused condition all materials, other than one enamelled steel, were equally cleanable. Stainless steel, abraded artificially or impact damaged to a similar degree as stainless steel subjected to domestic wear, retained approximately one log order less bacteria after cleaning than the other materials subjected to the same treatments. Little difference in cleanability was recorded between the abraded surfaces of the other materials although enamelled steel surfaces were less cleanable than mineral resin or polycarbonate after impact damage, because of the greater susceptibility of enamelled steel to damage by this treatment. When cleaning time was extended beyond 10 s for the abraded and impact damaged materials, their cleanability was not enhanced as compared with stainless steel. Changes in surface finish after abrasion were assessed by surface roughness measurement and scanning electron microscopy. Surfaces with poor cleanability before and after abrasion were characterized by pitting, crevices or jags. These surfaces are likely to retain more bacteria because of increased numbers of attachment sites, a larger bacterial/material surface contact area and topographical areas in which applied cleaning shear forces are reduced. Materials that resist surface changes, e.g. stainless steel, will remain more hygienic when subjected to natural wear than materials which become more readily damaged.     

An all-metal block for replica plating of microbial colonies

The surface of a metal block made of an aluminium alloy is covered with narrow perpendicular grooves, which thus form an array of quadrangular pyramids touching base to base. The surface is further provided with a marker which assures the positioning of the master plate and the replica plate. Replicas prepared using this block are of higher quality than those using the velveteen-covered cylinder. A single master plate will provide ten or more replicas of good quality, the master plate being preserved for further work. Last but not least, the all-metal block can be easily cleaned and heat-sterilized.     

Description of Chytridiopsis Trichopterae N. Sp. (Microspora, Chytridiopsidae), A Microsporidian Parasite of the Caddis Fly Polycentropus Flavomaculatus (Trichoptera, Polycentropodidae), With Comments On Relationships Between the Families Chytridiopsidae and Metchnikovellidae

ABSTRACT. The microsporidium Chytridiopsis trichopterae n. sp., a parasite of the midgut epithelium of larvae of the caddis fly Polycentropus flavomaculatus found in southern Sweden, is described based on light microscopic and ultrastructural characteristics. All life cycle stages have isolated nuclei. Merogonial reproduction was not observed. the sporogony comprises two sequences: one with free spores in parasitophorous vacuoles, the other in spherical, 5.6-6.8 μm wide, sporophorous vesicles which lie in the cytoplasm. the free sporogony yields more than 20 spores per sporont. the vesicle-bound sporogony produces 8, 12 or 16 spores. the envelope of the sporophorous vesicle is about 82 nm thick and layered. the internal layer is the plasma membrane of the sporont; the surface layer is electron dense with regularly arranged translucent components. Both spore types are spherical. They have an ～ 35-nm thick spore wall, with a plasma membrane, an electron-lucent endospore, and an ～ 14-nm thick electron-dense exospore. the polar sac is cup-like and lacks a layered anchoring disc. the polar filament is arranged in two to three isofilar coils in the half of the spore opposite the nucleus. the coupling between the polar sac and the polar filament is characteristic. the surface of the polar filament is covered with regularly arranged membraneous chambers resembling a honeycomb. There is no polaroplast of traditional type. the cytoplasm lacks polyribosomes. the nucleus has a prominent, wide nucleolus. the two spore types have identical construction, but differ in dimensions and electron density. Free living spores are about 3.2 μm wide, the diameter of the polar filament proper is 102-187 nm, the chambers of the honeycomb are 70-85 nm high, and the polar sac is up to 425 nm wide. Living spores in the vesicle-bound sporogony are about 2.1 μm wide, the polar filament measures 69-102 nm, the chambers of the honeycomb are about 45 nm high, and these spores are more electron dense. Comparisons of cytology (especially the construction of the spore wall and the polar filament and associated structures) and life cycles reveal prominent differences among the Chytridiopsis-like microsporidia, and close relationships between the families Chytridiopsidae and Metchnikovellidae.     

Effectiveness of vacuum cleaning and wet cleaning in reducing house-dust mites,fungi and mite allergen in a cotton carpet: A case study

In order to evaluate the effect of continuous, thorough vacuuming on house dust organisms and mite allergen, a cotton carpet was vacuumed every other day, six times in total. Seven weeks later, the carpet was cleaned by means of spray extraction. Samples were taken before and after this wet cleaning.In total 1150 g of dust was collected, containing approximately 174 000 arthropods (dead and alive) and 9000×10⁶ fungal spores. In the course of the experiment, the amount of dust collected at each vacuuming decreased. The number of extracted house dust mites did not decrease significantly, but that of the predator miteCheyletus did. The number of extracted fungal spores showed a significant decrease (from 142 to 16×10⁶ spores/m² per minute vacuuming), as did the extracted mite allergen per m². After 7 weeks the number of mite eggs and complete house dust mites had increased enormously. After cleaning by spray extraction another increase in the number of complete mites and mite eggs was found, while the amount of mite allergen was diminished.The population growth of the house dust mite between the 6th and the 7th vacuuming is probably due to the decrease of their most important predator,Cheyletus. After the wet cleaning a number of extra eggs hatched, probably due to the high humidity in the carpet. The procedures used in this study to combat house dust mites may have an adverse effect in the long run.     

Biofouling of reverse osmosis membranes: effects of cleaning on biofilm microbial communities,membrane performance,and adherence of extracellular polymeric substances

Laboratory-scale reverse osmosis (RO) flat-sheet systems were used with two parallel flow cells, one treated with cleaning agents and a control (ie undisturbed). The cleaning efforts increased the affinity of extracellular polymeric substances (EPS) to the RO membrane and altered the biofilm surface structure. Analysis of the membrane biofilm community composition revealed the dominance of Proteobacteria. However, within the phylum Proteobacteria, γ-Proteobacteria dominated the cleaned membrane biofilm, while β-Proteobacteria dominated the control biofilm. The composition of the fungal phyla was also altered by cleaning, with enhancement of Ascomycota and suppression of Basidiomycota. The results suggest that repeated cleaning cycles select for microbial groups that strongly attach to the RO membrane surface by producing rigid and adhesive EPS that hampers membrane performance.     

Effect of Manual Brush Cleaning on Biomass and Community Structure of Microfouling Film Formed on Aluminum and Titanium Surfaces Exposed to Rapidly Flowing Seawater

Metals exposed to rapidly flowing seawater are fouled by microbes that increase heat transfer resistance. In this study, results of biochemical test methods quantitatively relating the biomass and community structure of the microfouling film on aluminum and titanium to heat transfer resistance across the metal surface during three cycles of free fouling and manual brushing showed that cleaning accelerates the rate of fouling measured as the loss of heat transfer efficiency and as microfouling film biomass. The results also showed that the rate of fouling, measured as an increase in heat transfer resistance, is faster on titanium than on aluminum but that the titanium surface is more readily cleaned. In three cycles of free fouling and cleaning with a stiff-bristle nylon brush, the free-fouling communities re-forming on aluminum became enriched in bacteria containing short-branched fatty acids as the cycling progressed. The free-fouling community on titanium revealed an increasingly diverse morphology under scanning electron microscopy that was enriched in a portion of the microeucaryotes. Brushing removed most of the biomass, but left a residual community that was relatively enriched in a portion of the bacterial assembly containing cyclopropane fatty acids on aluminum and in a more diverse community on the titanium surface. The residual communities left after cleaning of titanium revealed an increase in bacteria with short-branched fatty acids and in microeucaryotes as cleaning continued. No significant changes occurred in the residual microbial community structure left on aluminum with cleaning; it was, again, less diverse than that remaining on titanium. The residual communities secreted a twofold-larger amount of extracellular polymer, measured as the ratio of total organic carbon to lipid phosphate, than did the free-fouling community on both surfaces.     

Cleanability in relation to bacterial retention on unused and abraded domestic sink materials

H olah , J.T. & T horpe , R.H. 1990. Cleanability in relation to bacterial retention on unused and abraded domestic sink materials. Journal of Applied Bacteriology 69 , 599–608.
The relative Cleanability of stainless steel, enamelled steel, mineral resin and polycarbonate domestic sink materials was assessed by comparing the number of organisms remaining on surfaces after cleaning. In unused condition all materials, other than one enamelled steel, were equally cleanable. Stainless steel, abraded artificially or impact damaged to a similar degree as stainless steel subjected to domestic wear, retained approximately one log order less bacteria after cleaning than the other materials subjected to the same treatments. Little difference in Cleanability was recorded between the abraded surfaces of the other materials although enamelled steel surfaces were less cleanable than mineral resin or polycarbonate after impact damage, because of the greater susceptibility of enamelled steel to damage by this treatment. When cleaning time was extended beyond 10 s for the abraded and impact damaged materials, their Cleanability was not enhanced as compared with stainless steel. Changes in surface finish after abrasion were assessed by surface roughness measurement and scanning electron microscopy. Surfaces with poor Cleanability before and after abrasion were characterized by pitting, crevices or jags. These surfaces are likely to retain more bacteria because of increased numbers of attachment sites, a larger bacterial/material surface contact area and topographical areas in which applied cleaning shear forces are reduced. Materials that resist surface changes, e.g. stainless steel, will remain more hygienic when subjected to natural wear than materials which become more readily damaged.     

Ease of removal of barnacles from various polymeric materials

The forces required to remove living, fully attached barnacles from the surface of a number of polymeric solids were measured. The forces were related to the surface energy components of the materials. The results indicate a positive correlation between polymer surface energy and force required for barnacle removal. The nonpolar component of the surface energy was more closely related to the removal force than the polar component, although the polar component is significant. Adherence to some composite materials was greater than was consistent with the correlation for noncomposites.     

Ectoparasites: are they the proximate cause of cleaning interactions?

We tested the importance of ectoparasites in cleaning symbioses by comparing the activity of Caribbean cleaning gobies ( Elacatinus evelynae ) and of their clients during three daily periods (early morning, midday and late afternoon) in which ectoparasite availability varied naturally. Emergence from the benthos of gnathiid isopod larvae, the main target of cleaning goby predation, was higher at night, when cleaners are inactive, than during the day. Overall ectoparasite loads also tended to be higher on clients in the morning. This coincided with higher rates of visits to cleaning stations by client fish in the morning than at midday, but high rates of client visits were also recorded in the late afternoon. Clients were more likely to adopt stereotypical incitation poses, which increase the likelihood of being cleaned, in the morning than later in the day. Inspection bouts by cleaning gobies were longest in the morning. Cleaner and client behaviours therefore change predictably in response to natural diurnal variation in ectoparasite availability. These results add to a growing number of studies supporting the idea that cleaning symbioses are mutualisms dependent on ectoparasite removal.     

Adhesion of Bacillus spores and Escherichia coli cells to inert surfaces: role of surface hydrophobicity

The ability of bacterial spores and vegetative cells to adhere to inert surfaces was investigated by means of the number of adherent spores (Bacillus cereus and Bacillus subtilis spores) and Escherichia coli cells and their resistance to cleaning or rinsing procedures (adhesion strength). Six materials (glass, stainless steel, polyethylene high density (PEHD), polyamide-6, polyvinyl chloride, and Teflon) were tested. Slight differences in the number of adherent spores (less than 1 log unit) were observed between materials, but a higher number of adherent E. coli cells was found on the hydrophobic materials PEHD and Teflon. Conversely, the resistance of both B. cereus and B. subtilis spores to a cleaning procedure was significantly affected by the material. Hydrophobic materials were harder to clean. The topography parameter derived from the Abbott-Firestone curve, RVK, and, to a lesser extent, the widely used roughness parameters RA (average roughness) and Rz (maximal roughness), were related to the number of adherent cells. Lastly, the soiling level as well as the adhesion strength were shown to depend largely on the microorganism. The number of adhering B. cereus hydrophobic spores and their resistance to a cleaning procedure were found to be 10 times greater than those of the B. subtilis hydrophilic spores. Escherichia coli was loosely bound to all the materials tested, even after 24 h biofilm formation.     

Studies on Spore Morphology of Some Chinese Sphagnum L

The spores of 5 species and 1 subspecies of Sphagnum in China were examined under LM and SEM, and one of them under TEM. All of the above spores are radial symmetrical, tetrahedral, rounded-triangular in polar view and 36.1-55.7 μm in diameter. Among them, the size of the spores of S. cuspidatum is the largest. Trilete is distinct, narrow and slightly curved, ca. 1/3-1/2 of the spore radius, margo very distinct under SEM, perine with gemmae and verrucae. The sporoderm of Sphagnum contains perine, exine and intine. On the basis of spore morphology, the point of view that Sphagnum is a primitive genus in mosses is supported. In sporo-pollen analysis the spores of Sphagnum are easily confused with some spores of ferns.     

Study on the Spore Morphology of Subfam. Polypodioideae ( Polypodiaceae) in Yunnan,China

The spores of 8 species and 1 variety belonging to 4 genera of Polypodiaceae subfam. Polypodioideae in Yunnan, China were examined under LM and SEM. Of the species it is the first time to study the spores of Metapolyp odium manmeiense and Polypodiastrum mengtzeense under SEM. The results show that the spores of this subfam. Polypodioideae are morphologic uniform; they are monolete, bilaterally symmetric, ellipsoidal in polar view, bean- shaped in equatorial view, and with or without perispore. The surface ornamentation is regularly verrucate. In addition, the relationship of the spore morphology and taxonomy in Polypodiaceae subfam. Polypodioideae was discussed in this paper, providing more informative data for the systematics and palynology of Polypodiaceae.