The long-term effects of ethanol on immobilized cell reactor performance using K. fragilis

The effects of ethanol on reactor performance were studied in a small, 5-cm packed height, "differential" type immobilized cell reactor. Lactose utilizing yeast cells, Kluyveromyces fragilis, were absorbed to a porous adsorbant sponge matrix in a gas continuous reactor. Step changes in the feed ethanol concentration to the column (10-130 g/L) were used to test the reactor response over extended periods of time (about 30-50 h per dosage level) followed by a return to basal zero inlet ethanol feed. Effluent cell density and effluent cell viability were measured at intervals. An inhibitory response in ethanol productivity to feed dosage ethanol levels above 20 g/L was detected almost immediately, with a near steady state response noted within 2.5 h of initiating the dosage. Feed ethanol levels above 50 g/L resulted in a subsequent gradual decrease in reactor productivity over time, which was associated with a decrease in the fraction of viable shed cells in the reactor effluent. The reactor response to a step removal of the ethanol inhibition was also monitored. Quick and complete rebounding of the fermentation rate to the original basal rate was noted following dosage concentrations of under 50 g/L ethanol. Recovery rates slowed following ethanol dosage levels above 50 g/L. Viable shed cell density improved overtime during the slow recovery periods. Growth rates (as determined by shed cell density) were more strongly inhibited than productivity. Growth responded more slowly to changes in ethanol environment as growth rates at 30 h fell to about 40% of the rates measured 7.5 h after initiation of a dosage level. It is concluded that ethanol contributions to cell injury and death (and consequent ICR performance degradation) may be more important than ethanol inhibition of productivity rates in the long-term operation of immobilized cell reactors at ethanol concentrations over 50 g/L.     

Comparative study of ethanol production by an immobilized yeast in a tubular reactor and in a multistage reactor

Summary The productivity of continuous ethanol fermentation has been increased using fixed bed reactors where a high density of yeast cells was maintained on a packing of wood chips. Two different systems have been used: 1. A tubular reactor which produced alcohol solutions containing up to 13.5% (V/V) ethanol. High CO₂ retention and a poor mass transfer between bulk medium and immobilized biomass prevented production rates higher than 2.2 g/l·h. 2. A multistage reactor where a better utilisation of the reactor volume led to improved performances. Solutions containing 132 g/l of ethanol (16.5% V/V) were produced with a productivity increased up to 4.8 g/l·h. A better distribution of the active biomass and a lower gradient of alcohol concentration between support and bulk medium are possible reasons for this improvement.     

Performance of tapered column packed-bed bioreactor for ethanol production

A tapered column type of bioreactor system packed with immobilized Saccharomyces cerevisiae was used to study the bioreactor performance as a function of design and operating variables. The performance of tapered column bioreactor system was found to be better than that of the conventional cylindrical column reactor system for the ethanol fermentation. The new bioreactor design alleviated problems associated with carbon dioxide evolution and provided a significantly better flow pattern for both liquid and gas phases in the bioreactor without local channelling. A mathematical simulation model, which takes into account of the axial convection and dispersion, interphase mass transfer, and apparent kinetic design parameters, was developed. The effect of radial concentration gradients on the bioreactor performance was found to be insignificant. For the reactor system studied, the maximum ethanol productivity obtained was 60 g ethanol/L gel/h, and the maximum glucose assimilation rate was 140 g glucose/L gel/h. One of the most important findings from this study was that the apparent kinetic parameters change at the glucose concentration of 2 g/L This change was found to be due to the changes in yeast physiology and metabolism. The values of V(m) (') and V(m) (') decreased from 0.8 to 0.39 g ethanol/g cell/h and from 97mM to 11mM, respectively. The substrate inhibition constant was estimated as 0.76M and the product inhibition constant was determined as 113 g ethanol/L The degree of product inhibition showed practically a linear relationship with an increasing ethanol concentration. Based on the hydro-dynamic analysis of the bioreactor system, it was found that the Peclet number, N(Pe) was not a strong function of the flow velocity at low flow rates through the bioreactor system, but its value decreased somewhat at an interstitial velocity greater than 0.03 cm/s. The tapered column bioreactor system showed a much better flow pattern of gas and liquid phases within the reactor, thereby providing a more homogeneous distribution of gas-liquid-solid phases in the reactor without any phase separation.     

One-pot bioethanol production from cellulose by co-culture of Acremonium cellulolyticus and Saccharomyces cerevisiae

ABSTRACT: BACKGROUND: While the ethanol production from biomass by consolidated bioprocess (CBP) is considered to be the most ideal process, simultaneous saccharification and fermentation (SSF) is the most appropriate strategy in practice. In this study, one-pot bioethanol production, including cellulase production, saccharification of cellulose, and ethanol production, was investigated for the conversion of biomass to biofuel by co-culture of two different microorganisms such as a hyper cellulase producer, Acremonium cellulolyticus C-1 and an ethanol producer Saccharomyces cerevisiae. Furthermore, the operational conditions of the one-pot process were evaluated for maximizing ethanol concentration from cellulose in a single reactor. RESULTS: Ethanol production from cellulose was carried out in one-pot bioethanol production process. A. cellulolyticus C-1 and S. cerevisiae were co-cultured in a single reactor. Cellulase producing-medium supplemented with 2.5 g/l of yeast extract was used for productions of both cellulase and ethanol. Cellulase production was achieved by A. cellulolyticus C-1 using Solka-Floc (SF) as a cellulase-inducing substrate. Subsequently, ethanol was produced with addition of both 10%(v/v) of S. cerevisiae inoculum and SF at the culture time of 60 h. Dissolved oxygen levels were adjusted at higher than 20% during cellulase producing phase and at lower than 10% during ethanol producing phase. Cellulase activity remained 8--12 FPU/ml throughout the one-pot process. When 50--300 g SF/l was used in 500 ml Erlenmeyer flask scale, the ethanol concentration and yield based on initial SF were as 8.7--46.3 g/l and 0.15--0.18 (g ethanol/g SF), respectively. In 3-l fermentor with 50--300 g SF/l, the ethanol concentration and yield were 9.5--35.1 g/l with their yields of 0.12--0.19 (g/g) respectively, demonstrating that the one-pot bioethanol production is a reproducible process in a scale-up bioconversion of cellulose to ethanol. CONCLUSION: A. cellulolyticus cells produce cellulase using SF. Subsequently, the produced cellulase saccharifies the SF, and then liberated reducing sugars are converted to ethanol by S. cerevisiae. These reactions were carried out in the one-pot process with two different microorganisms in a single reactor, which does require neither an addition of extraneous cellulase nor any pretreatment of cellulose. Collectively, the one-pot bioethanol production process with two different microorganisms could be an alternative strategy for a practical bioethanol production using biomass.     

Alcoholic fermentation by agar-immobilized yeast cells

Immobilized yeast cells in agar gel beads were used in a packed bed reactor for the production of ethanol from cane molasses at 30°C, pH 4.5. The maximum productivity, 79.5g ethanol/l.h was obtained with 195g/l reducing sugar as feed. Substrate (64.2%) was utilized at a dilution of 1.33h^-1. The immobilized cell reactor was operated continuously at a constant dilution rate of 0.67h^-1 for 100 days. The maximum specific ethanol productivity and specific sugar uptake rate were 0.610g ethanol/g cell.h and 1.275g sugar/g cell.h, respectively.     

Fed-batch production of concentrated fructose syrup and ethanol using Saccharomyces cerevisiae ATCC 36859

A fed-batch process is used for the production of concentrated pure fructose syrup and ethanol from various glucose/fructose mixtures by S. cerevisiae ATCC 36859. Applying this technique, glucose-free fructose syrups with over 250 g/l of this sugar were obtained using High Fructose Corn Syrup and hydrolyzed Jerusalem artichoke juice. By encouraging ethanol evaporation from the reactor and condensing it, a separate ethanol product with a concentration of up to 350 g/l was also produced. The rates of glucose consumption and ethanol production were higher than in classical batch ethanol fermentation processes.     

Alcoholic fermentation of D-xylose by immobilizedPichia stipitis yeast

Summary Pichia stipitis NRRL Y-7124 yeast cells were for the first time immobilized both in agar gel beads and on fine nylon net for ethanol fermentation on D-xylose, in order to investigate the possibility of using the biocatalyst for improved utilization of the biomass pentose fraction. With free cells the initial xylose level affected little ethanol production, with a maximum of 22 g/l ethanol obtained in 5 days on 5% and of 40 g/l in 8 days on 10% xylose, and an average volumetric productivity of about 0.22 g/lh. The maximum ethanol concentration of 19.5% on 5% xylose with the nylon net attached cells in a continuous packed-bed column reactor was obtained with 35 h residence time. The volumetric productivities of 0.56 g/lh at 19.5 g/l ethanol and 1.0 g/lh at 15.0 g/l ethanol were markedly higher than those obtained with free cells. The stability of the immobilized biocatalyst was excellent. The same reactor could be used for at least 80 days without significant activity loss.     

Ethanol fermentation in an immobilized cell reactor using Saccharomyces cerevisiae

Fermentation of sugar by Saccharomyces cerevisiae, for production of ethanol in an immobilized cell reactor (ICR) was successfully carried out to improve the performance of the fermentation process. The fermentation set-up was comprised of a column packed with beads of immobilized cells. The immobilization of S. cerevisiae was simply performed by the enriched cells cultured media harvested at exponential growth phase. The fixed cell loaded ICR was carried out at initial stage of operation and the cell was entrapped by calcium alginate. The production of ethanol was steady after 24 h of operation. The concentration of ethanol was affected by the media flow rates and residence time distribution from 2 to 7 h. In addition, batch fermentation was carried out with 50 g/l glucose concentration. Subsequently, the ethanol productions and the reactor productivities of batch fermentation and immobilized cells were compared. In batch fermentation, sugar consumption and ethanol production obtained were 99.6% and 12.5% v/v after 27 h while in the ICR, 88.2% and 16.7% v/v were obtained with 6 h retention time. Nearly 5% ethanol production was achieved with high glucose concentration (150 g/l) at 6 h retention time. A yield of 38% was obtained with 150 g/l glucose. The yield was improved approximately 27% on ICR and a 24 h fermentation time was reduced to 7 h. The cell growth rate was based on the Monod rate equation. The kinetic constants (K(s) and mu(m)) of batch fermentation were 2.3 g/l and 0.35 g/lh, respectively. The maximum yield of biomass on substrate (Y(X-S)) and the maximum yield of product on substrate (Y(P-S)) in batch fermentations were 50.8% and 31.2% respectively. Productivity of the ICR were 1.3, 2.3, and 2.8 g/lh for 25, 35, 50 g/l of glucose concentration, respectively. The productivity of ethanol in batch fermentation with 50 g/l glucose was calculated as 0.29 g/lh. Maximum production of ethanol in ICR when compared to batch reactor has shown to increase approximately 10-fold. The performance of the two reactors was compared and a respective rate model was proposed. The present research has shown that high sugar concentration (150 g/l) in the ICR column was successfully converted to ethanol. The achieved results in ICR with high substrate concentration are promising for scale up operation. The proposed model can be used to design a lager scale ICR column for production of high ethanol concentration.     

Ethanol fermentation in a magnetically fluidized bed reactor with immobilized Saccharomyces cerevisiae in magnetic particles

Ethanol fermentation by immobilized Saccharomyces cerevisiae cells in magnetic particles was successfully carried out in a magnetically stabilized fluidized bed reactor (MSFBR). These immobilized magnetic particles solidified in a 2 % CaCl(2) solution were stable and had high ethanol fermentation activity. The performance of ethanol fermentation of glucose in the MSFBR was affected by initial particle loading rate, feed sugar concentration and dilution rate. The ethanol theoretical yield, productivity and concentration reached 95.3%, 26.7 g/L h and 66 g/L, respectively, at a particle loading rate of 41% and a feed dilution rate of 0.4 h(-1) with a glucose concentration of 150 g/L when the magnetic field intensity was kept in the range of 85-120 Oe. In order to use this developed MSFBR system for ethanol production from cheap raw materials, cane molasses was used as the main fermentation substrate for continuous ethanol fermentation with the immobilized S. cerevisiae cells in the reactor system. Molasses gave comparative ethanol productivity in comparison with glucose in the MSFBR, and the higher ethanol production was observed in the MSFBR than in a fluidized bed reactor (FBR) without a magnetic field.     

Continuous production of ethanol from fructose by immobilized growing cells of Zymomonas mobilis

Immobilized growing cells of Zymomonas mobilis were found to ferment rapidly and efficiently media containing 100 g/L fructose in a continuous reactor. A volumetric ethanol productivity of 94.8 g/L h was achieved at a substrate conversion of 75.5%. With 97% conversion of substrate the productivity was 28.4 g/L h. At fructose concentrations of 150 and 200 g/L substrate and product inhibitions limited the performance of the reactor. Ethanol production was constant over a period of 55 days.     

Production of ethanol by coupling fermentation and solvent extraction

Summary A new technology of fermentation is proposed. The inhibitor product is removed continuously by coupling fermentation and solvent extraction. Applied to ethanol fermentation this technology is suitable to any case where the terminal product is inhibitory.The proposed technology uses both plug flow reactor and liquid-liquid extraction to achieve continuously the extractive fermentation of ethanol. The solvent used for liquid-liquid extraction is dodecanol. A new reactor was used. It is a column packed with a porous material . The fermentation broth is pulsed (a) to increase the interfacial area between the liquid medium and the dodecanol, and (b) to: decrease the gas hold up.Alcoholic fermentations were performed on glucose syrup at 35°C using Saccharomyces cerevisiae, with adsorbed cells as reference, with adsorbed cells and extractive fermentation. The results show that the fermentation is substantially improved. By this new method the ethanol productivity was multiplied by 5 and a solution of 407 g/l of glucose was totally fermented with a yeast which cannot normally transform more than 200 g/l glucose.     

Continuous fermentation of feed streams containing D-glucose and D-xylose in a two-stage process utilizing immobilized Saccharomyces cerevisiae and Pachysolen tannophilus

In the U.S., forest and crop residues contain enough glucose and xylose to supply 10 times the country's usage of ethanol and ethylene, but an efficient fermentation scheme is lacking,(1,2,3) To develop a strategy for process design, specific ethanol productivities and yields of Pachysolen tannophilus NRRL Y-2460 and Saccharomyces cerevisiae NRRL Y-2235 were compared. Batch cultures and continuous stirred reactors (CSTR) loaded with immobilized cells were fed glucose and xylose. As expected from previous reports, Y-2235 fermented glucose but not xylose. Y-2460 consumed both sugars but fermented glucose inefficiently relative to Y-2235, and it suffered a diauxic lag lasting 10-20 h when given a sugar mixture. Immobilized Y-2235 exhibited increasing productivity but constant yield with in creasing glucose concentration. In contrast, Y-2460 exhibited an optimum productivity at 30-40 g/L xylose and a declining yield with increasing xylose concentration. Immobilized Y-2235 tolerated more than 100 g/L ethanol while the productivity and yield of Y-2460 fell by 80 and 58%, respectively, as ethanol reached 50 g/L. A 38.8-g/L ethanol stream could be produced as 103 g/L xylose was continuously fed to Y-2460. If it was blended with a 274 g/L glucose stream to give a composite of 23.7 g/L ethanol and 107 g/L glucose, Y-2235 could en rich the ethanol to 75 g/L. Taken together these results suggest use of a two-stage continuous reactor for pro cessing xylose and glucose from lignocellulose. An immobilized Y-2460 CSTR (or cascade) would convert the hemicellulose hydrolyzate. Then downstream, an immobilized Y-2235 plug flow reactor would enrich the hemicellulose-derived ethanol to more than 70 g/L upon addition of cellulose hydrolyzate.     

Production of ethanol by adsorbed yeast cells

Summary Various ion exchange resins were tested for their ability to adsorb cells of Saccharomyces cerivisiae with the ultimate intention of developing a packed bed immobilized cell reactor for the continuous production of ethanol. The resins varied greatly in their ability to adsorb cells - the least effective resins retained less than 1 mg S. cerivisiae cells (dry weight)/g of resin (dry weight), and the most effective, 130–140 mg cells/g of resin. A column reactor packed with adsorbed yeast cells was operated continuously for over 200 hours using a 12% (w/v) glucose medium at dilution rates of 1.1 h^-1 and 1.44 h^-1 (based on void volume). High ethanol productivities of 53.1 and 62.0 g ethanol/l-h were obtained.     

Continuous ethanol production by immobilized yeast reactor coupled with membrane pervaporation unit

A system comprised of an immobilized yeast reactor producing ethanol, with a membrane pervaporation module for continuously removing and concentrating the produced ethanol, was developed. The combined system consisted of two integrated circulation loops: In one the sugar-containing medium is circulated through the membrane pervaporation module. The two loops were interconnected in a way allowing for separate parameter optimization (e.g., flow rate, temperature, pH) for each loop.The fermentation unit was 2.0 L bioreactor with five equal segments, packed with 5-mm beads of immobilized yeasts. The bead matrix was a crosslinked polyacrylamide hydrazide gel coated with calcium alginate. The fast circulation loop of the bioreactor allowed for efficient liberation of CO(2) at the top of the immobilized yeast reactor. Continuous operation of the uncoupled reactor for over 50 days with inflowing defined medium or dilute molasses at a residence time of 1.25 h yielded ethanol at a rate of about 10 g/L h.The pervaporation unit was constructed from four 60-cm-long tubular membranes of silicone composite on a polysulfone support. The output from the fermentor was circulated through the inside of the tubes of a unit with a total surface area of 800 cm(2), having an average flux of 150 mL/h, and selectivities to ethanol vs. water up to 7. A vacuum of 30 mb was applied to the outside of the tubes, removing 20-30 g of ethanol per hour, which was collected in condensors. The continuous removal of ethanol, avoiding inhibition of the fermentation process, resulted in an improved productivity and allowed the use of high sugar concentrations (40% wt/vol) offering the potential of a compact system with reduced stillage.The combined system of ethanol production and removal enabled an operative steady state at which the liquid volume of the system, and the concentrations of ethanol within the reactor ( 4% wt/vol), as well as within the flux crossing the pervaporation membrane (17%-20% wt/vol) were kept constant. At the steady state, a 40% wt/vol sugar solution could be continuously added to the fermentor when 12%-20% wt/vol clear ethanol solution was continuously removed by the pervaporation unit. Membrane fouling was reversed by short washing steps, and continuous step operation was maintained by working with two different modules that were interchanged. In this manner, long term continuous operation (over 40 days) was achieved with a productivity of 20-30 g/L h, representing over a twofold increase relative to the continuously operated reactor uncoupled from the membrane and a fivefold increase in comparison with the value obtained fro a corresponding batch fermentation.     

Comparative study of d-xylose conversion to ethanol by immobilized growing or non-growing cells of the yeast Pachysolen tannophilus

Summary The direct conversion of d-xylose to ethanol was investigated using immobilized growing and non-growing cells of the yeast Pachysolen tannophilus. Both preparations produced ethanol from d-xylose, however the d-xylose conversion to ethanol was much better with immobilized growing cells. Ethanol concentration up to 22.9 g/l and ethanol yield of 0.351 g/g of d-xylose were obtained in batch fermentation by immobilized growing cells whereas only 17.0 g/l and 0.308 g/g of d-xylose were obtained by immobilized non-growing cells. With continuous systems, immobilized growing cells were necessary for the long-term operation, since a steady state ethanol concentration of 17.7 g/l was maintained for only one week by immobilized non-growing cell reactor. With simultaneous control of aeration rate and concentrations of nitrogen sources in feed medium, immobilized growing cells of P. tannophilus showed excellent performance. At a residence time of 25 h, the immobilized cell reactor produced 26.9 g/l of ethanol from 65 g/l of d-xylose in feed medium.     

Inulin enrichment by fermentation in a flocculating yeast reactor

Summary Simultaneous production of ethanol and fructose enriched syrups was obtained from Jerusalem artichoke extract using a Saccharomyces diastaticus flocculating yeast in a continuous gas-lift reactor with internal biomass recycle. This allowed the production of 42 g/L of ethanol and 70 g/L of inulin containing up to 92% fructose (fructose/glucose ratio of 11). These results can be compared to the batch and chemostat fermentations which gave a higher ethanol concentration but a lower fructose enrichment. Mass transfert limitations can explain both the productivity decrease and the selectivity improvement in the gas-lift reactor.     

Kinetics of ethanol fermentations in membrane cell recycle fermentors

Ethanol fermentation by yeast was carried out in a cell filtration recycle system with a hollow-fiber membrane filter. Maximum biomass concentrations up to 210 g dry wt/L were obtained, but in normal operation concentrations they were between 100 and 150 g/L. The ethanol productivity using 14% glucose feed was 85 g/L h, with an ethanol concentration of 65 g/L and an ethanol yield of over 90%. The ethanol productivity and yeast growth rate decreased as the cell concentration increased beyond a certain level. The cell mass in the reactor was maintained by a proper manipulation of diluticn rate and bleed ratio depending on the growth rate.     

Continuous ethanol production by immobilized yeast in a fluidized reactor

Summary In order to minimize the adverse effect of CO₂ gas in a packed bed immobilized yeast reactor, a fluidized bed reactor was used for the continuous production of ethanol from glucose. Immobilized yeast was prepared by entrapping whole cells of Saccharomyces cerevisiae within a Caalginate matrix. It was found that the efficiency of the ethanol production in a fluidized bed reactor was 100% better than that for a packed bed reactor system. The alcohol productivity obtained was 21 g/l/hr in a fluidized bed reactor at 94% of conversion level.     

Cell growth and death rates as factors in the long-term performance, modeling, and design of immobilized cell reactors

The viable fraction of immobilized cells in a bioreactor may be critical in predicting long-term or steady-state reactor performance. The assumption of near 100% viable cells in a bioreactor may not be valid for portions of immobilized cell reactors (ICRs) characterized by conditions resulting in appreciable death rates. A mathematical model of an adsorbed cell type ICR is presented in which a steady-state viable cell fraction is predicted, based on the assumptions of no cell accumulation in the reactor and a random loss of cells from the reactor. Data on cell death rates, cell growth rates, and productivity rates as functions of temperature, substrate, and ethanol concentration for the lactose utilizing yeast K. fragillis were incorporated into this model. The steady-state reactor viable cell fraction as predicted by this model is a strong function of both temperature and ethanol concentration. For example, a stable 20% viable fraction of the immobilized cells is predicted in ICR locations experiencing continuous conditions of either 30 g/L ethanol at 40 degrees C, or 95 g/L ethanol at 25 degrees C. Steady-state ICR "plug flow" concentration profiles and column productivities are predicted at three operating temperatures, 20, 30, and 40 degrees C using two different models for ethanol inhibition of productivity. These profiles suggest that the reactor operating temperature should be low if higher outlet ethanol concentrations are desired. Three reactor design strategies are presented to maximize the viable cell fraction and improve long-term ethanol productivity in ICR's: (1) reducing outlet ethanol concentrations, (2) rotating segments of an ICR between high and low ethanol environments, and (3) simultaneous removal of the ethanol produced from the reactor as it is formed.     

Development of a serial bioreactor system for direct ethanol production from starch using<Emphasis Type="Italic">Aspergillus niger</Emphasis> and<Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis>

Aspergillus niger hyphae were found to grow with unliquefied potato starch under aerobic conditions, but did not grow under anaerobic conditions. The raw culture ofA. niger catalyzed saccharification of potato starch to glucose, producing approximately 12 g glucose/L/day/ The extracellular enzyme activity was decreased in proportion to incubation time, and approximately 64% of initial activity was maintained after 3 days. At 50°C,A. niger hyphae growth stopped, while the extracellular enzyme activity peaked. On the basis of theA. niger growth property and enzyme activity, we designed a serial bioreactor system composed of four different reactors. Fungal hyphae were cultivated in reactor I at 30°C, uniquefied starch was saccharified to glycose by a fungal hyphae culture in reactors II and III at 50°C, and glucose was fermented to ethanol bySaccharomyces cerevisiae in reactor IV. The total glucose produced by fungal hyphae in reactor I and saccharification in reactor II was about 42 g/L/day. Ethanol production in reactor IV was approximately 22 g/L/day, which corresponds to about 79% of the theoretical maximum produced from 55 g starch/L/day.