固态发酵生产腺苷酸脱氨酶

对多株曲霉产腺苷酸脱氨酶的性能进行了比较,发现米曲霉3.800(Aspergillus oryzae)产酶水平较高。该菌株固态发酵产酶的适宜培养基为：以麸皮为主原料,蔗糖2％,鱼粉2％,（NH4）2SO4 0．1％,柠檬酸钠0．2％,MgSO4 0.05%,吐温－80 0．1％,含水量50％。最佳的培养条件为：250mL三角瓶装20g培养基,在28－30℃培养60h。在优化条件下,培养物酶活可达到1543．48u/g鲜曲。     

黑曲霉固态发酵生产单宁酶的条件优化

研究采用响应面法优化黑曲霉固态发酵生产单宁酶的培养条件。应用Plackett—Burman试验筛选出重要影响因子：五倍子粉含量、（NH4）2SO4浓度以及接种孢子量,最陡爬坡试验逼近最大响应区域。应用Box．Behnken响应面试验对重要影响因子进一步优化。得到最佳培养条件：每250mL三角瓶中装入1．0g五倍子粉、4．4g稻壳和0．5g麸皮、液固比（mL／g）2：1且营养盐溶液组成为（NH4）2s0421g/L、MgSO4·7H2O1g／L、NaCl1g／L,培养基pH自然,接种5．7×10^7个孢子后在30℃温度下培养4d。在此条件下,单宁酶产量从40U／g提高到114U／g,3次重复验证性试验平均值为115U／g,验证了模型的可靠性。     

角质蛋白酶固态发酵工艺及酶解条件的研究

曲霉Ａ２８－８是一株优良的角蛋白酶分泌突变菌株。其最佳固体发酵培养基为：２０％羽毛粉,８０％麸皮和微量无机氮（每克培养基中加０．５ｍｇ）;最适产酶条件为：起始ｐＨ７．５～８．０,温度２８℃～３０℃,时间为６０～７０小时,酶活高达２５００ＫＵ／ｇ曲;最适酶解条件为ｐＨ７．０～９．０,温度４５℃～５０℃。     

Statistical optimization for tannase production from <Emphasis Type="Italic">Aspergillus niger</Emphasis> under submerged fermentation

Statistically based experimental design was employed for the optimization of fermentation conditions for maximum production of enzyme tannase from Aspergillus niger. Central composite rotatable design (CCRD) falling under response surface methodology (RSM) was used. Based on the results of ‘one-at-a-time’ approach in submerged fermentation, the most influencing factors for tannase production from A. niger were concentrations of tannic acid and sodium nitrate, agitation rate and incubation period. Hence, to achieve the maximum yield of tannase, interaction of these factors was studied at optimum production pH of 5.0 by RSM. The optimum values of parameters obtained through RSM were 5% tannic acid, 0.8% sodium nitrate, 5.0 pH, 5 × 10⁷ spores/50mL inoculum density, 150 rpm agitation and incubation period of 48 h which resulted in production of 19.7 UmL⁻¹ of the enzyme. This activity was almost double as compared to the amount obtained by ‘one-at-a-time’ approach (9.8 UmL⁻¹).     

Production profiles of phenolics from fungal tannic acid biodegradation in submerged and solid-state fermentation

Potent antioxidant phenolics are derived from tannin biodegradation. Understanding of biodegradation pathways through the identification of the intermediates molecules of great value like tannins is important to pursuit the production of bioactive monomers. Biodegradation of tannins remains poorly understood due to their chemical complexity and reactivity. Tannic acid biodegradation by Aspergillus niger GH1 in submerged fermentation (SF) and solid state fermentation (SSF) was evaluated by liquid chromatography coupled to mass spectrometry (LC–MS). Both cultures were kinetically monitored for the biodegradation profiles during 72 h. Differences in tannic acid composition were evidenced and the consumption of substrate and identification of biodegradation intermediates were achieved. The mechanism of tannic acid degradation by A. niger GH1 is by degradation of high molecular weight gallotannins and highly polymerized tannins to small molecules like gallic acid, digalloyl glucose and trigalloyl glucose. Important differences on time of substrate uptake and product release were revealed.     

Exploring the Chemical and Biological Potential of Jamun (Syzygium cumini (L.) Skeels) Leaves: A Comprehensive Review

Leaves of jamun collected as agro by-produce during the cultivation of jamun is traditionally used as ayurvedic medicine to treat diabetes, gall bladder stones and other ailments. Most of the beneficial effects of jamun leaves are associated with phytochemicals found in jamun leaves such as gallic acid, tannins, mallic acid, flavonoids, essential oils, jambolin, ellagic acid, jambosine, antimellin and betulinic acid. Jamun possess curative activities like anticancer, antidiabetic, antifertility, anti-inflammatory, antidiarrheal, antimicrobial, antinociceptive, antioxidant, antiradiation, chemotherapeutic, and gastroprotective. The main goal of this review article is to provide information on the nutritional content, phytochemical composition and health promoting properties of jamun leaves. The review of literature based on the phytochemical composition and health promoting benefits of the jamun leaves, suggests that leaves can be used as potential constituent in the formulation of pharmacological drugs. From the review literature it is found that clinical, in-vivo, in-vitro studies are still required to check the health promoting effects of jamun leaves extracts on humans.     

Extracellular L-asparaginase production in solid-state fermentation by using sugarcane bagasse as support material

Abstract

L-asparaginase is an important enzyme used in the pharmaceutical and food industry, which can be produced by different microorganisms using low cost feedstocks. In this work, sugarcane bagasse (SCB) was used as support for enzyme production in solid-state fermentation (SSF) by A. terreus. Initially, the influence of the variables carbon and nitrogen sources on the enzyme production was studied following an experimental design carried out in Erlenmeyer flasks. Statistical analysis indicated the use of 0.54% of starch, 0% of maltose, 0.44% of asparagine, and 1.14% of glutamine in the medium, resulting in enzyme activity per volume of produced extract of 120.723?U/L. Then, these conditions were applied in a horizontal column reactor filled with SCB, producing 105.3?U/L of enzyme activity. Therefore, the potential of extracellular L-asparaginase enzyme production in the column reactor using sugarcane bagasse as support was demonstrated and it represents a system that can favor large scale production.     

黑曲霉A3木聚糖酶固体发酵研究

筛选了一株高产木聚糖酶的黑曲霉Ａ３菌株,研究了其在固体培养基中的发酵条件。该菌最适培养条件为：起始ｐＨ４．６。２８℃,１ｍｌ孢子悬液接种量,蔗渣粉：麸皮为１．５：１,发酵３天,木聚糖酶活力可达５１４７ＩＵ／ｇ培养基干重。氮源组成,温度、ｐＨ及发酵时间对曲中木聚糖酶和纤维素酶的比例有较大影响。与液体发酵相比,粗酶的最适反应温度均为５５℃,最适反应ｐＨ值分别为４．６和４．２,在不同温度下保温１ｈ,测得     

黑曲霉固态发酵及酶解玉米皮

以玉米提取淀粉后的玉米皮渣为主要原料,采用黑曲霉固态发酵法产酶再酶解的二步法降解玉米皮中纤维素类物质。经Plackett-Burman法及响应面设计优化发酵条件得:温度30℃,接种量10%,初始水分体积分数60%,物料厚度2.47 cm,初始pH 5.79,发酵时间6 d;滤纸比酶活可达11.01 U/g,较原始酶活提高了40.61%;产酶结束后加入pH 4.8醋酸-醋酸钠缓冲液,置于50℃下酶解144 h,中性洗涤纤维与酸性洗涤纤维降解率分别为46.09%、48.82%,还原糖质量分数达到9.02%。     

黑曲霉B0201利用五倍子固体发酵产单宁酶的条件研究

通过比较常规灭菌发酵和生料发酵, 研究黑曲霉B0201利用五倍子固体发酵产单宁酶的条件。结果表明, 在生料发酵过程中, 采用20%五倍子并且以(NH4)2SO4为氮源制备单宁酶的最佳条件为: 液固比=1.6:1、温度30°C、初始pH 6.0。在该条件下通过96 h的培养, 单宁酶的活力可达51.2 U/gds, 是常规灭菌发酵的3.6倍。以上结果显示, 生料发酵生产单宁酶是一种高效可行的方法。     

Citric and gluconic acid production from fig by Aspergillus niger using solid-state fermentation

The production of citric and gluconic acids from fig by Aspergillus niger ATCC 10577 in solid-state fermentation was investigated. The maximal citric and gluconic acids concentration (64 and 490 g/kg dry figs, respectively), citric acid yield (8%), and gluconic acid yield (63%) were obtained at a moisture level of 75%, initial pH 7.0, temperature 30°C, and fermentation time in 15 days. However, the highest biomass dry weight (40 g/kg wet substrate) and sugar utilization (90%) were obtained in cultures grown at 35°C. The addition of 6% (w/w) methanol into substrate increased the concentration of citric and gluconic acid from 64 and 490 to 96 and 685 g/kg dry fig, respectively. Journal of Industrial Microbiology & Biotechnology (2000) 25, 298–304. Received 15 April 2000/ Accepted in revised form 11 August 2000     

Improved xylanase production using apple pomace waste by Aspergillus niger in koji fermentation

Xylanase production by Aspergillus niger NRRL‐567 in solid‐state fermentation (koji fermentation) was optimized using 2⁴ factorial design and response surface methodology. The evaluated variables were the initial moisture level and concentration of inducers [veratryl alcohol (VA), copper sulphate (CS), and lactose (LAC)], leading to the response of xylanase production. Initial moisture level and LAC were found to be the most significant variable for xylanase production (p<0.05). The highest xylanase production was observed with 3578.8 ± 65.3 IU/gds (gram dry substrate) under optimal conditions using initial moisture of 85% (v/w), pH 5.0 and inducers VA (2 mM/kg), LAC 2% (w/w), and CS (1.5 mM/kg) after 48 h of incubation time. Higher xylanase activity of 3952 ± 78.3 IU/gds was attained during scale‐up of the process in solid‐state tray fermentation under optimum conditions after 72 h of incubation time. The present study demonstrates that A. niger NRRL‐567 can efficiently be used to achieve xylanase production with an economical and environmental benefit in solid‐state tray fermentation. The developed process can be used to develop an effective process for commercially feasible bioproduction of xylanases for speciality applications, such as conversion of lignocellulosic biomass to biofuels and other value‐added products.     

Citric acid production by Aspergillus niger ATCC 9142 from a treated ethanol fermentation co-product using solid-state fermentation

Aims:  To investigate the ability of the citric acid-producing strain Aspergillus niger ATCC 9142 to utilize the ethanol fermentation co-product corn distillers dried grains with solubles for citric acid production following various treatments.
Methods and Results:  The ability of A. niger ATCC 9142 to produce citric acid and biomass on the grains was examined using an enzyme assay and a gravimetric method, respectively. Fungal citric acid production after 240 h was higher on untreated grains than on autoclaved grains or acid-hydrolysed grains. Fungal biomass production was enhanced after autoclaving and acid-hydrolysis of the grains. Phosphate supplementation to the grains slightly stimulated citric acid production while methanol addition decreased its synthesis. Using the phosphate-supplemented grains, the optimal incubation temperature, initial moisture content of the grains and the length of fermentation time for ATCC 9142 citric acid production were determined to be 25°C, 82% and 240 h, respectively.
Conclusions:  A. niger ATCC 9142 synthesized citric acid on corn distillers dried grains with solubles. The phosphate-treated grains increased citric acid production by the strain.
Significance and Impact of the Study:  The ethanol fermentation co-product corn distillers dried grains with solubles could be useful commercially as a substrate for A. niger citric acid production.     

Citric acid production by solid state fermentation using sugarcane bagasse

A solid state fermentation (SSF) method was used to produce citric acid by Aspergillus niger DS 1 using sugarcane bagasse as a carrier and sucrose or molasses based medium as a moistening agent. Initially bagasse and wheat bran were compared as carrier. Bagasse was the most suitable carrier, as it did not show agglomeration after moistening with medium, resulting in better heat and mass transfer during fermentation and higher product yield. Different parameters such as moisture content, particle size, sugar level and methanol concentration of the medium were optimised and 75% moisture level, 31.8 g sugar/100 g dry solid, 4% (v/w) methanol and particles of the size between 1.2 and 1.6 mm were found to be optimal. Sucrose and clarified and non-clarified molasses medium were also tested as moistening agents for SSF and under optimised conditions, 20.2, 19.8 and 17.9 g citric acid /100 g of dry solid with yield of 69.6, 64.5 and 62.4% (based on sugar consumed) was obtained in sucrose, clarified and non-clarified molasses medium respectively, after 9 days of fermentation.     

Production of tannase by Aspergillus niger Aa-20 in submerged and solid-state fermentation: influence of glucose and tannic acid

Tannase production by Aspergillus niger Aa-20 was studied in submerged (SmF) and solid-state (SSF) fermentation systems with different tannic acid and glucose concentrations. Tannase activity and productivity were at least 2.5 times higher in SSF than in SmF. Addition of high tannic acid concentrations increased total tannase activity in SSF, while in SmF it was decreased. In SmF, total tannase activity increased from 0.57 to 1.03 IU/mL, when the initial glucose concentration increased from 6.25 to 25 g/L, but a strong catabolite repression of tannase synthesis was observed in SmF when an initial glucose concentration of 50 g/L was used. In SSF, maximal values of total tannase activity decreased from 7.79 to 2.51 IU when the initial glucose concentration was increased from 6.25 to 200 g/L. Kinetic results on tannase production indicate that low tannase activity titers in SmF could be associated to an enzyme degradation process which is not present in SSF. Tannase titers produced by A. niger Aa-20 are fermentation system-dependent, favoring SSF over SmF. Journal of Industrial Microbiology & Biotechnology (2001) 26, 296–302. Received 07 July 2000/ Accepted in revised form 15 February 2001     

Phytase isozymes from Aspergillus niger NCIM 563 under solid state fermentation: Biochemical characterization and their correlation with submerged phytases

Aspergillus niger NCIM 563 produces dissimilar phytase isozymes under solid state and submerged fermentation conditions. Biochemical characterization and applications of phytase Phy III and Phy IV in SSF and their comparison with submerged fermentation Phy I and Phy III were studied. SSF phytases have a higher metabolic potential as compared to SmF. Phy I is tetramer and Phy II, III and IV are monomers. Phy I and IV have pH optima of 2.5 and Phy II and III have pH optima of 5.0 and 5.6, respectively. Phy I, III and IV exhibited very broad substrate specificity while Phy II was more specific for sodium phytate. SSF phytase is less thermostable as compared to SmF phytase. Phy I and II show homology with other known phytases while Phy III and IV show no homology with SmF phytases and any other known phytases from the literature suggesting their unique nature. This is the first report about differences among phytase produced under SSF and SmF by A. niger and this study provides basis for explanation of the stability and catalytic differences observed for these enzymes. Exclusive biochemical characteristics and multilevel application of SSF native phytases determine their efficacy and is exceptional.     

Contribution of aerial hyphae of Aspergillus oryzae to respiration in a model solid-state fermentation system

Oxygen transfer is for two reasons a major concern in scale-up and process control in industrial application of aerobic fungal solid-state fermentation (SSF): 1) heat production is proportional to oxygen uptake and it is well known that heat removal is one of the main problems in scaled-up fermenters, and 2) oxygen supply to the mycelium on the surface of or inside the substrate particles may be hampered by diffusion limitation. This article gives the first experimental evidence that aerial hyphae are important for fungal respiration in SSF. In cultures of A. oryzae on a wheat-flour model substrate, aerial hyphae contributed up to 75% of the oxygen uptake rate by the fungus. This is due to the fact that A. oryzae forms very abundant aerial mycelium and diffusion of oxygen in the gas-filled pores of the aerial hyphae layer is rapid. It means that diffusion limitation in the densely packed mycelium layer that is formed closer to the substrate surface and that has liquid-filled pores is much less important for A. oryzae than was previously reported for R. oligosporus and C. minitans. It also means that the overall oxygen uptake rate for A. oryzae is much higher than the oxygen uptake rate that can be predicted in the densely packed mycelium layer for R. oligosporus and C. minitans. This would imply that cooling problems become more pronounced. Therefore, it is very important to clarify the physiological role of aerial hyphae in SSF.     

Production and partial characterization of xylanase by Sporotrichum thermophile under solid-state fermentation

A number of factors affecting production of xylanase, by the thermophilic fungus Sporotrichum thermophile under solid state fermentation (SSF) were investigated. Initial moisture content and type of carbon source were consecutively optimized. Solid state fermentation in a laboratory horizontal bioreactor using the optimized medium allowed the production of 320 U g^–1 of carbon source which compared favourably with those reported for other microorganisms. Optimal xylanase activity was observed at pH 5 and 70 °C. Chromogenic (fluorogenic) 4-methylumbelliferyl -glycoside of xylobiose (MUX₂) was used to characterize the xylanase multienzyme component, after separation by isoelectric focusing and native PAGE electrophoresis. The zymograms indicated one major xylanase fraction exhibiting pI and molecular mass values 4 and 90–120 kDa, respectively.