Growth and substrate consumption of Nitrobacter agilis cells immobilized in carrageenan: part 2. Model evaluation

A dynamic model that predicts substrate and biomass concentration profiles across gel beads and from that the overall substrate consumption rate by the gel beads containing growing cells was evaluated with immobilized Nitrobacter agilis cells in an airlift loop reactor with oxygen as the limiting substrate. The model predictions agreed well with the observed oxygen consumption rates at three different liquid phase oxygen concentrations. Image analysis showed that 90% of the immobilized cells after 42 days of cultivation was situated in the outer shells in a film of 140 mum, while the bead radius was about 1 mm. The maximum biomass concentration in the outmost film of 56 mum was 11 kg . m(-3) gel.     

Accurate and rapid viability assessment of Trichoderma harzianum using fluorescence-based digital image analysis

Fluorescence microscopy and image analysis were evaluated in order to assess the viability of Trichoderma harzianum, an economically important filamentous fungus. After the evaluation of the two most commonly used fluorochromes, acridine orange (AO) and fluorescein diacetate (FDA) as metabolic indicator stains, AO gave ambiguous results and therefore FDA was chosen. The lower stability at room temperature and fast fluorescence intensity decay (50% after only 30 s of illumination in UV light) could be overcome by the use of a digital image acquisition system including frame grabber and a video camera. Fresh (live) fungal hyphae emitted bright green fluorescence when stained with this dye (7.5 microg/L), whereas a total absence of fluorescence was observed when using sterilized (dead) fungal cells. Fresh cells were subjected to different lethal and sublethal treatments and the percentage of FDA stained fluorescent hyphae was then measured over the total hyphal area (% of FDA-stained area) by image analysis. At the same time, samples were cultivated in shake flasks in order to correlate this % of FDA-stained area with its growth rate, a functional indicator of viability. The linear correlation (r = 0.979) was: growth rate (g/L x h) = 2.25 x 10(-3) (% of FDA-stained area). This method was used to evaluate the viability of the fungus under two different fermentation conditions in a 10-L bioreactor. Estimated viable biomass during fermentation was strongly influenced by the process conditions. The use of FDA, with computer-aided quantitative image analysis, has made it possible to rapidly and reliably quantify the viability of T. harzianum.     

Specific ATP and specific oxygen uptake rate in immobilized cell aggregates: Experimental results and theoretical analysis using a structured model of immobilized cell growth

In this work the quality and activity of immobilized Beneckea natriegens have been measured using Specific ATP (SATP) [mg (ATP) g(-1) (dry biomass)] and Specific Oxygen Uptake Rate (SOUR) [mg O(2) g(-1) (dry biomass) h(-1)]. The cells were grown in a 3 L Three Phase Air Lift Bioreactor (TPALB) and were immobilized on diatomaceous earth (silica) support particles; sterile conditions were employed during the experiment, with n-propanol as the sole carbon source. Two sets of experiments were performed, one with varying dilution rate and the other with varying inlet substrate concentration. The average SATP and SOUR of the immobilized biomass was 3-4 times lower than the values obtained for suspended Beneckea natriegens growing at its maximum growth rate. The suspended biomass present in the TPALB was generated primarily through attrition from the outer layer of the biofilm, and maintained higher levels of SATP and SOUR than the immobilized biomass. This result indicates that the immobilized biomass quality/activity is higher at the external layer of the biofilm. A structured model in which biomass is divided into two compartments, active and inert, was used to describe the experimental results. This model predicts the biomass quality/activity and substrate concentration distributions in the biofilm. These distributions were integrated to give overall values of SATP and SOUR for the immobilized biomass which compared favorably with experimental data. The primary implication of the results is that the location of immobilized biomass in the biofilm affects its biocatalytic activity, and should be taken into account when modeling immobilized biomass bioreactors. (c) 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 55: 660-673, 1997.     

The viability of Scenedesmus bicellularis cells immobilized on alginate screens following nutrient starvation in air at 100% relative humidity

The viability of algal cells immobilized on screens and starved in a water-saturated air stream was studied at the laboratory scale. This new process for wastewater biotreatment has been developed using immobilized cells, which were starved in air, to obtain a high rate of nutrient removal. A unicellular green microalgae, Scenedesmus bicellularis, was isolated from secondary decantation tanks at an urban wastewater treatment plant and grown in a synthetic medium for 12 days. The cells were then concentrated by centrifugation and immobilized on alginate screens. The screens were then inserted in a photochamber saturated at 100% relative humidity and subjected to a photoperiod of 16 h in the light and 8 h in the dark, with an illumination of 150 muE m(-2) s(-1) provided by fluorescent lamps. After 48 h of nutrient starvation, the immobilized cells were used for the removal of ammonium and orthophosphate from a synthetic secondary wastewater effluent in a plexiglass reactor. During the sequential operation of starvation followed by incubation in the presence of nutrients, fast growth of viable cells in the gel matrix was obtained and there was no appreciable decay of chlorophyll a or cell activity. When these immobilized and starved cells were incubated in wastewater, ammonium (NH(4) (+)) and orthophosphate (PO(4) (3-)) ions were quickly taken up from medium. After three successive 2-h exposures to wastewater, immobilized algal cells were freed by dissolving the Ca-alginate with phosphate as 0.2 M Na(3)PO(4) and resuspended in fresh culture medium. Results indicate that free cells transferred to rich medium remained viable, but the growth rate revealed that the viable cells decreased their culturability. (c) 1995 John Wiley & Sons, Inc.     

Removal and biodegradation of nonylphenol by immobilized Chlorella vulgaris

The removal and biodegradation of nonylphenol (NP) by alginate-immobilized cells of Chlorella vulgaris were compared with their respective free cultures. The effects of four cell densities of 10(4) per algal bead were investigated, as were the four algal bead concentrations, with regard to the removal and biodegradation of NP. Although immobilization significantly decreased the growth rate and NP's biodegradation efficiency of C. vulgaris, NP removal over a short period was enhanced. The NP removal mechanism by immobilized cells was similar to that by free cells, including adsorption onto alginate matrix and algal cells, absorption within cells and cellular biodegradation. The optimal cell density and bead concentration for the removal and biodegradation of NP was 50-100×10(4) cells algal bead(-1) and 2-4 beads ml(-1) of wastewater, respectively. These results demonstrated that immobilized C. vulgaris cells under optimal biomass and photoautotrophic conditions are effective in removing NP from contaminated water.     

Growth and death behaviour of anchorage-independent animal cells immobilized within porous support matrices

Summary Growth and death of anchorage-independent animal cells entrapped within porous biomass support particles (BSPs) in static or shake-flask cultures were evaluated by comparison of enzyme activity with non-immobilized cells grown under static culture using 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) assay and release of lactate dehydrogenase into the culture medium. Mouse myeloma MPC-11 (ATCC CCL 167) cells inoculated within porous polyvinyl formal resin BSPs (3 × 3 × 3 or 2 × 2 × 2 mm; mean pore diameter, 60 ) grew exponentially at a specific growth rate comparable to that of non-immobilized cells in the initial period of incubation. Entrapped cells then reached the stationary phase with a cell density over 10⁷ cells/cm³ BSP. The death rate of entrapped cells increased in response to the rise in viable cell density in the BSPs. Observation of viable cell distribution within the BSPs using MTT staining indicated that the cells concentrated within a thin outer shell of the BSPs with time. After the immobilized cells reached the stationary phase, penetration of cells into the outer shell ceased and heterogeneous distribution of cell density occurred in the viable cell layer in the shake-flask culture.     

Use of ATP to characterize biomass viability in freely suspended and immobilized cell bioreactors

This work describes investigations into the viability of cells growing on 3,4-dichloroaniline (34DCA). Two bioreactors are employed for microbial growth, a continuous stirred tank (CST) bioreactor with a 2-L working volume, and a three-phase air lift (TPAL) bioreactor with a 3-L working volume. Experiments have been performed at several dilution rates between 0.027 and 0.115 h(-1) in the CST bioreactor and between 0.111 and 0.500 h(-1) in the TPAL bioreactor. The specific ATP concentration was calculated at each dilution rate in the suspended biomass in both bioreactors as well as in the immobilized biomass in the TPAL bioreactor. The ATP was extracted from the cells using boiling tris-EDTA buffer (pH 7.75), and the quantity determined using a firefly (bioluminescence) technique. The cultures were inspected under an electron microscope to monitor compositional changes. Results from the CST bioreactor showed that the biomass-specific ATP concentration increases from 0.44 to 1.86 mg ATP g(-1) dry weight (dw) as dilution rate increases from 0.027 to 0.115 h(-1). At this upper dilution rate the cells were washed out. The specific ATP concentration reached a limiting average value of 1.73 mg ATP g(-1) dw, which is assumed to be the quantity of ATP in 100% viable biomass. In the TPAL bioreactor, the ATP level increased with dilution rate in both the immobilized and suspended biomass. The specific ATP concentration in the immobilized biomass increased from approximately 0.051 mg ATP g(-1) dw at dilution rates between 0.111 and 0.200 h(-1) to approximately 0.119 mg ATP g(-1) dw at dilution rates between 0.300 and 0.500 h(-1). This indicates that the immobilized biomass contained a viable cell fraction of around 5%. Based on these results, kinetic data for freely suspended cells should not be applied to the modeling of immobilized cell systems on the assumption that immobilized biomass is 100% viable. (c) 1993 John Wiley & Sons, Inc.     

Regulation of growth and adhesion of cultured cells by insulin conjugated with thermoresponsive polymers

We developed a new biomaterial for use in cell culture. The biomaterial enabled protein-free cell culture and the recovery of viable cells by lowering the temperature without the aid of supplements. Insulin was immobilized and a thermoresponsive polymer was grafted onto a substrate. We investigated the effect of insulin coupling on the lower critical solution temperature (LCST) of the thermoresponsive polymer, poly(N-isopropylacrylamide-co-acrylic acid), using polymers that were ungrafted, or coupled with insulin. The insulin conjugates were precipitated from an aqueous solution at high temperatures, but they were soluble at low temperatures. The LCST was not significantly affected by the insulin coupling. The thermoresponsive polymer was grafted to glow-discharged polystyrene film and covalently conjugated with insulin. The surface wettability of the conjugate film was high at low temperatures and low at high temperatures. The amounts of immobilized insulin required to stimulate cell growth were 1-10% of the amount of free insulin required to produce the same effect. The maximal mitogenic effect of immobilized insulin was greater than that of free insulin. About half of the viable cells was detached from the film only by lowering the temperature. The recovered cells proliferated normally on new culture dishes. (c) 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 53: 339-344, 1997.     

Immobilization of Escherichia coli Cells Containing Aspartase Activity with Polyurethane and Its Application for l-Aspartic Acid Production

Whole cells of Escherichia coli containing aspartase activity were immobilized by mixing a cell suspension with a liquid isocyanate-capped polyurethane prepolymer (Hypol). The immobilized cell preparation was used to convert ammonium fumarate to l-aspartic acid. Properties of the immobilized E. coli cells containing aspartase were investigated with a batch reactor. A 1.67-fold increase in the l-aspartic acid production rate was observed at 37 degrees C as compared to 25 degrees C operating temperature. The pH optimum was broad, ranging from 8.5 to 9.2. Increasing the concentration of ammonium fumarate to 1.5 M from 1.0 M negatively affected the reaction rate. l-Aspartic acid was produced at an average rate of 2.18 x 10 mol/min per g (wet weight) of immobilized E. coli cells with a 37 degrees C substrate solution consisting of 1.0 M ammonium fumarate with 1 mM Mg (pH 9.0).     

Growth and morphology of thermophilic dairy starters in alginate beads

The aim of this research was to produce concentrated biomasses of thermophilic lactic starters using immobilized cell technology (ICT). Fermentations were carried out in milk using pH control with cells microentrapped in alginate beads. In the ICT fermentations, beads represented 17% of the weight. Some assays were carried out with free cells without pH control, in order to compare the ICT populations with those of classical starters. With Streptococcus thermophilus, overall populations in the fermentor were similar, but maximum bead population for (8.2 x 10(9) cfu/g beads) was 13 times higher than that obtained in a traditional starter (4.9 x 10(8) cfu/ml). For both Lactobacillus helveticus strains studied, immobilized-cell populations were about 3 x 10(9) cfu/g beads. Production of immobilized Lb. bulgaricus 210R strain was not possible, since no increases in viable counts occurred in beads. Therefore, production of concentrated cell suspension in alginate beads was more effective for S. thermophilus. Photomicrographs of cells in alginate beads demonstrated that, while the morphology of S. thermophilus remained unchanged during the ICT fermentation, immobilized cells of Lb. helveticus appeared wider. In addition, cells of Lb. bulgaricus were curved and elongated. These morphological changes would also impair the growth of immobilized lactobacilli.     

Survival of Bifidobacterium longum Immobilized in Calcium Alginate Beads in Simulated Gastric Juices and Bile Salt Solution

Bifidobacterium longum KCTC 3128 and HLC 3742 were independently immobilized (entrapped) in calcium alginate beads containing 2, 3, and 4% sodium alginate. When the bifidobacteria entrapped in calcium alginate beads were exposed to simulated gastric juices and a bile salt solution, the death rate of the cells in the beads decreased proportionally with an increase in both the alginate gel concentration and bead size. The initial cell numbers in the beads affected the numbers of survivors after exposure to these solutions; however, the death rates of the viable cells were not affected. Accordingly, a mathematical model was formulated which expressed the influences of several parameters (gel concentration, bead size, and initial cell numbers) on the survival of entrapped bifidobacteria after sequential exposure to simulated gastric juices followed by a bile salt solution. The model proposed in this paper may be useful for estimating the survival of bifidobacteria in beads and establishing optimal entrapment conditions.     

Survival of Bifidobacterium longum immobilized in calcium alginate beads in simulated gastric juices and bile salt solution

Bifidobacterium longum KCTC 3128 and HLC 3742 were independently immobilized (entrapped) in calcium alginate beads containing 2, 3, and 4% sodium alginate. When the bifidobacteria entrapped in calcium alginate beads were exposed to simulated gastric juices and a bile salt solution, the death rate of the cells in the beads decreased proportionally with an increase in both the alginate gel concentration and bead size. The initial cell numbers in the beads affected the numbers of survivors after exposure to these solutions; however, the death rates of the viable cells were not affected. Accordingly, a mathematical model was formulated which expressed the influences of several parameters (gel concentration, bead size, and initial cell numbers) on the survival of entrapped bifidobacteria after sequential exposure to simulated gastric juices followed by a bile salt solution. The model proposed in this paper may be useful for estimating the survival of bifidobacteria in beads and establishing optimal entrapment conditions.     

Relationship between fluorescein diacetate-stained hyphae and oxygen utilization, glucose utilization, and biomass of submerged fungal batch cultures.

The relationship between fungal activity and staining with fluorescein diacetate (FDA) was investigated by growing Penicillium citrinum and Rhizoctonia solani in submerged batch cultures at different initial glucose concentrations and aeration rates. A modified FDA staining method, similar to the Jones and Mollison technique (P. Jones and J. Mollison, J. Gen. Microbiol. 2:54-69, 1948), was developed to assess both total and FDA-stained hyphae. In previous studies, soil hyphae stained with FDA were considered viable. However, determination of a quantitative relationship between FDA staining and fungal activity is necessary before such an assumption can be made. Growth rates and the rate of change in the percentage of FDA-stained hyphae were significantly correlated. The regression equation calculated for the relationship was: growth rate (mg . ml-1 . h-1) = 0.34 + 1.1 (rate of change in the percentage of FDA-stained hyphae [. ml-1 . h-1]). Changes in activity as measured by O2 utilization, glucose utilization, and biomass correlated significantly with changes in the percentage of FDA-stained hyphae, although the relationships among these parameters were different for each fungal species. Fungal growth stage was also correlated with the percentage of FDA-stained hyphae. Staining was 10% or greater during fungal growth and less than 10% during the late growth, stationary, and death phases. Thus, the rate of change in the percentage of FDA-stained hyphae can be used to predict fungal activity rate changes for single fungal cultures and growth rates for mixed fungal cultures, and the growth stage can be assessed by the percentage of FDA-stained hyphae.     

The use of fluorogenic esters to detect viable bacteria by flow cytometry

The ability of flow cytometry (FCM) to detect viable bacteria after staining with a range of fluorogenic esters was investigated with several bacterial species. The dyes studied were the fluorescein diacetate (FDA) derivatives carboxyfluorescein diacetate, 2',7'-bis-(2-carboxyethyl)-5(6)-carboxyfluorescein acetoxymethyl ester and calcein acetoxymethyl ester, as well as ChemChrome B, a commercially-available stain for the detection of viable bacteria in suspension. No one dye was found to be universal but ChemChrome B dye stained the widest number of Gram-positive and Gram-negative species, whereas the FDA derivatives preferentially stained Gram-positive bacteria. The use of ChemChrome B to detect viable bacteria in environmental samples was investigated further by studying the survival of Klebsiella pneumoniae in lakewater. During survival studies, a higher number of viable bacteria were detected both by direct viable counts and FCM after staining with rhodamine 123 and ChemChrome B than by colony-forming units, suggesting the presence of viable but nonculturable cells. These results demonstrate the potential use of FCM to enumerate viable bacteria in natural waters.     

Use of bioluminometry for determination of active yeast biomass immobilized in ionotropic hydrogels

The technique of bioluminometry was used to determine the biomass concentration of yeast cells immobilized in ionotropic hydrogel beads, including alginate, pectate, and kappa-carrageenan. The method uses determination of ATP extracted from viable cells, the concentration of which is then expressed as the active biomass concentration. Seven yeast strains divided into three categories (brewing, wine-making, and ethanol-producing yeasts) were tested, and different biomass concentrations were determined in all three immobilization materials. The described method is characterized by a good correlation (up to 99%) to classical dry biomass determination. The method is quicker, easier, and not so laborious, providing sufficient determination accuracy, and can be used for a rapid estimation of viable biomass in most biotechnological processes using immobilized living cells.     

Exopolysaccharide production during batch cultures with free and immobilized Lactobacillus rhamnosus RW-9595M

AIMS: Exopolysaccharides (EPS) were produced by Lactobacillus rhamnosus RW-9595M during pH-controlled batch cultures with free cells and repeated-batch cultures with cells immobilized on solid porous supports (ImmobaSil). METHODS AND RESULTS: Cultures were conducted in supplemented whey permeate (SWP) medium containing 5 or 8% (w/w) whey permeate. For free-cell batch cultures in 8% SWP medium, very high maximum cell counts (1.3 x 10(10) CFU ml(-1)) and EPS production (2350 mg l(-1)) were measured. A high EPS production (1750 mg l(-1)) was measured after four cycles for a short incubation period of only 7 h. Several methods for immobilized biomass determination based on analysis of biomass components (proteins, ATP and DNA) were tested. The DNA analysis method proved to be the most appropriate under these circumstances. This method revealed a high maximum immobilized biomass of 8.5 x 10(11) CFU ml(-1) support during repeated immobilized cell cultures in 5% SWP. The high immobilized biomass increased maximum EPS volumetric productivity (250 mg l(-1) h(-1) after 7 h culture) compared with free-cell batch cultures (110 mg l(-1) h(-1) after 18 h culture). CONCLUSIONS: High EPS productions were achieved during batch cultures of Lact. rhamnosus RW-9595M in SWP medium, exceeding 1.7 g EPS per litre. Repeated-batch cultures with immobilized cells resulted in increased EPS productivity compared with traditional free-cell cultures. SIGNIFICANCE AND IMPACT OF THE STUDY: The study clearly shows the high potential of the strain Lact. rhamnosus RW-9595M and immobilized cell technology for production of EPS as a functional food ingredient.     

Preparation and activity of carbonic anhydrase immobilized on porous silica beads and graphite rods

Techniques for the immobilization of bovine carbonic anhydrase (BCA) on porous silica beads and graphite are presented. Surface coverage on porous silica beads was found to be 1.5 x 10(-5) mmol BCA/m(2), and on graphite it was 1.7 x 10(-3) mmol BCA/m(2) nominal surface area. Greater than 97% (silica support) and 85% (graphite support) enzyme activity was maintained upon storage of the immobilized enzyme for 50 days in pH 8 buffer at 4 degrees C. After 500 days storage, the porous silica bead immobilized enzyme exhibited over 70% activity. Operational stability of the enzyme on silica at 23 degrees C and pH 8 was found to be 50% after 30 days. Catalytic activity expressed as an apparent second-order rate constant K'(Enz) for the hydrolysis of p-nitrophenyl acetate (p-NPA) catalyzed by BCA immobilized on silica beads and graphite at pH 8 and 25 degrees C is 2.6 x 10(2) and 5.6 x 10(2) M(-1)s(-1) respectively. The corresponding K(ENZ) value for the free enzyme is 9.1 x 10(2) M(-1)s(-1). Activity of the immobilized enzyme was found to vary with pH in such a manner that the active site pK, on the porous silica bead support is 6.75, and on graphite it is 7.41. Possible reasons for a microenvironmental influence on carbonic anhydrase pK(a), are discussed. Comparison with literature data shows that the enzyme surface coverage on silica beads reported here is superior to previously reported data on silica beads and polyacrylamide gels and is comparable to an organic matrix support. Shifts in BCA-active site pK(a) values with support material, a lack of pH dependent activity studies in the literature, and differing criteria for reporting enzyme activity complicate literature comparisons of activity; however, immobilized BCA reported here generally exhibits comparable or greater activity than previous reports for immobilized BCA.     

Kinetcs and decay of fumarase activity of immobilized Brevibacterium ammoniagenes cells for continuous production of L-malic acid

The kinetics of the reversible fumarase reaction of immobilized Brevibacterium ammoniagenes cells and the decay behavior of enzyme activity were investigated in a plug flow system. The time course of the reaction in the immobilized cell column was well explained by the time-conversion equation including the apparent kinetic constants of the immobilized cell enzyme. The decay rate of fumarase activity was faster in the upper sections of the column (inlet side of the substrate solution) compared with the lower sections when 1M sodium fumarate (pH 7.0) was continuously passed through the column at 37°C. It was shown that the decay rate of the fumarase activity in the immobilized cell column depends on the flow rate of the substrate solution. The effect of flow rate on the decay rate of enzyme activity was considered to be related to the rate of contamination of enzyme with poisonous substances derived from the substrate solution or to the rate of leakage of enzyme stabilizers and/or enzyme itself from the immobilized cells.     

Cell growth and death rates as factors in the long-term performance, modeling, and design of immobilized cell reactors

The viable fraction of immobilized cells in a bioreactor may be critical in predicting long-term or steady-state reactor performance. The assumption of near 100% viable cells in a bioreactor may not be valid for portions of immobilized cell reactors (ICRs) characterized by conditions resulting in appreciable death rates. A mathematical model of an adsorbed cell type ICR is presented in which a steady-state viable cell fraction is predicted, based on the assumptions of no cell accumulation in the reactor and a random loss of cells from the reactor. Data on cell death rates, cell growth rates, and productivity rates as functions of temperature, substrate, and ethanol concentration for the lactose utilizing yeast K. fragillis were incorporated into this model. The steady-state reactor viable cell fraction as predicted by this model is a strong function of both temperature and ethanol concentration. For example, a stable 20% viable fraction of the immobilized cells is predicted in ICR locations experiencing continuous conditions of either 30 g/L ethanol at 40 degrees C, or 95 g/L ethanol at 25 degrees C. Steady-state ICR "plug flow" concentration profiles and column productivities are predicted at three operating temperatures, 20, 30, and 40 degrees C using two different models for ethanol inhibition of productivity. These profiles suggest that the reactor operating temperature should be low if higher outlet ethanol concentrations are desired. Three reactor design strategies are presented to maximize the viable cell fraction and improve long-term ethanol productivity in ICR's: (1) reducing outlet ethanol concentrations, (2) rotating segments of an ICR between high and low ethanol environments, and (3) simultaneous removal of the ethanol produced from the reactor as it is formed.     

Enhancement and stabilization of the production of glucoamylase by immobilized cells of Aureobasidium pullulans in a fluidized-bed reactor

Summary Glucoamylase production by Aureobasidium pollulans A-124 was compared in free-living cells, cells immobilized in calcium alginate gel beads aerated on a rotary shaker (agitation rate 150 rpm), and immobilized cells aerated in an air bubble column reactor. Fermentation conditions in the bioreactor were established for bead concentration, substrate (starch) concentration, calcium chloride addition to the fermentation medium, and rate of aeration. Production of glucoamylase was optimized at approximately 1.5 units of enzyme activity/ml medium in the bioreactor under the following conditions: aeration rate, 2.0 vol air per working volume of the bioreactor (280 ml) per minute; gel bead concentration, 30% of the working volume; substrate (starch) concentration, at 0.3% (w/v); addition of calcium chloride to the medium at a final concentration of 0.01 M. Productivity levels were stabilized through the equivalent of ten batches of medium with the original inoculum of immobilized beads. Offprint requests to: M. Petruccioli