Hydrolysis of cellulose in SO₃H-functionalized ionic liquids

Influence of acidity and structure of ionic liquids on microcrystalline cellulose (MCC) hydrolysis was investigated. MnCl₂-containing ionic liquids (ILs) were efficient catalysts and achieved MCC conversion rates of 91.2% and selectivities for 5-hydroxymethyl furfural (HMF), furfural and levulinic acid (LA) of 45.7%, 26.2% and 10.5%, respectively. X-ray diffractometry indicated that catalytic hydrolysis of MCC in ionic liquids resulted in the changes to MCC crystallinity and transformation of cellulose I into cellulose II. SO₃H-functionalized ionic liquids showed higher activities than non-functionalized ILs. The simplicity of the chemical transformation of cellulose provides a new approach for the use this polymer as raw material for renewable energy and chemical industries.     

An ionic liquid as reaction media for radiation-induced grafting of thermosensitive poly (N-isopropylacrylamide) onto microcrystalline cellulose

This paper reports a homogeneous modification of microcrystalline cellulose (MCC) in ionic liquids via radiation-induced grafting. Thermosensitive poly (N-isopropylacrylamide) (PNIPAAm) was successfully grafted onto MCC in 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) ionic liquid using γ-ray irradiation technique at room temperature. The grafting yield (GY) increased with dose up to 40 kGy, while decreased slightly with dose rate from 22 to 102 Gy/min. The results of TGA indicated that cellulose grafted PNIPAAm (cellulose-g-PNIPAAm) had higher thermal stability than that of ungrafted regenerated cellulose (reg-cellulose). The crystalline structure of original MCC was largely destroyed during the dissolution process according to the XRD profiles, and grafting PNIPAAm onto cellulose further decreased the intensity of crystallinity. SEM showed that reg-cellulose and cellulose-g-PNIPAAm films displayed dense and homogeneous morphology. Moreover, the resulting cellulose-g-PNIPAAm exhibited obvious thermal sensitivity with a lower critical solution temperature around 35 °C, which was observed from the swelling behavior in water at different temperatures.     

Preparation and characterization of bionanocomposite fiber based on cellulose and nano-SiO2 using ionic liquid

Microcrystalline cellulose (MCC)/nano-SiO₂ composite fibers were processed from solutions in 1-allyl-3-methylimidazolium chloride (AMIMCl) by the method of dry-jet wet spinning. The oscillatory shear measurements demonstrated that the gel network formed above 10 wt% nano-SiO₂ and the complex viscosity increased with increasing nano-SiO₂. Remarkably, the shear viscosity of the nanofluids was even lower than solutions without nano-SiO₂ under high shear rates. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images revealed that well-dispersed particles exhibit strong interfacial interactions with cellulose matrix. Measurements on wide-angle X-ray diffraction (WAXD) indicated that the regenerated cellulose and nanocomposite fibers were the typical cellulose II crystalline form, which was different from the native cellulose with the polymorph of Type I. The tensile strength of the nanocomposite fibers was larger than that of pure cellulose fiber and showed a tendency to increase and then decrease with increasing nano-SiO₂. Furthermore, the nanocomposite fibers exhibited improved thermal stability.     

Microwave-assisted conversion of lignocellulosic biomass into furans in ionic liquid

Production of 5-hydroxymethylfurfural (HMF) and furfural from lignocellulosic biomass was studied in ionic liquid in the presence of CrCl₃ under microwave irradiation. Corn stalk, rice straw and pine wood treated under typical reaction conditions produced HMF and furfural in yields of 45–52% and 23–31%, respectively, within 3 min. This method should be valuable to facilitate energy-efficient and cost-effective conversion of biomass into biofuels and platform chemicals.     

Enhancement of cellulose saccharification kinetics using an ionic liquid pretreatment step

Hydrolysis of cellulose to glucose in aqueous media catalyzed by the cellulase enzyme system suffers from slow reaction rates due in large part to the highly crystalline structure of cellulose and inaccessibility of enzyme adsorption sites. In this study, an attempt was made to disrupt the cellulose structure using the ionic liquid (IL), 1-n-butyl-3-methylimidazolium chloride, in a cellulose regeneration strategy which accelerated the subsequent hydrolysis reaction. ILs are a new class of non-volatile solvents that exhibit unique solvating properties. They can be tuned to dissolve a wide variety of compounds including cellulose. Because of their extremely low volatility, ILs are expected to have minimal environmental impact on air quality compared to most other volatile solvent systems. The initial enzymatic hydrolysis rates were approximately 50-fold higher for regenerated cellulose as compared to untreated cellulose (Avicel PH-101) as measured by a soluble reducing sugar assay.     

Efficient hydrolysis of chitosan in ionic liquids

Effective hydrolysis of chitosan, the N-deacetylated product of chitin, remains challenging. Here, we report acid-promoted hydrolysis of chitosan in imidazolium based ionic liquids with good total reducing sugars (TRS) yield under mild conditions. TRS yield reached over 60% in the presence of about 6.0 wt% concentrated hydrochloric acid at 100 °C within 7 h. Kinetic modeling of a typical experimental data set suggested that the hydrolysis most likely followed a consecutive first-order reaction sequence, where k₁ and k₂, the rate constants for TRS formation and degradation, were determined to be 0.01372 and 0.00015 min⁻¹, respectively. Our method may be useful to explore new applications of natural chitin resources.     

Enhanced enzyme-catalyzed synthesis of l-methionine with ionic liquid additives

The low solubility of l-methionine and low activity of enzyme are the major hurdles during l-methionine production by the enzymatic conversion approach. In this study, we investigated various ionic liquids (ILs) as additives for the enzyme-catalyzed production of l-methionine from O-acetyl L-homoserine and methyl mercaptan. Among the ILs evaluated, we found that tetraalkylammonium hydroxide ILs enhanced the solubility of l-methionine as well as the activity of the enzyme. Methionine solubility decreased with increasing alkyl chain length but increased with increasing IL concentration. l-methionine could be dissolved up to 232 g/L in 10% tetramethylammonium hydroxide solution. The enzyme O-acetylhomoserine aminocarboxypropyltransferase reached its maximum activity when the IL concentration was 2.5% (3 times higher than that without ILs) and significantly decreased with increasing IL concentration. The stability of the enzyme also decreased rapidly after 2 h of incubation regardless of the presence or absence of ILs. Nevertheless, 74 g/L of l-methionine could be produced in a reaction media containing 2.5% tetraethylammonium hydroxide compared to 35 g/L of l-methionine obtained in a reaction system without ILs.     

Natural wool/cellulose acetate blends regenerated from the ionic liquid 1-butyl-3-methylimidazolium chloride

Dissolution and blending one of the most commonly used natural polymers, i.e., wool using a green solvent ionic liquid is described. The cleaned natural wool from merino sheep was directly dissolved and regenerated from 1-butyl-3-methylimidazolium chloride (BMIMCl) without any modifications. BMIMCl was subsequently used to develop wool/cellulose acetate (CA) blends. Blending modification of wool in this IL green solvent led to significant increase in glass transition temperature (T_g) and thermal stability compared to the pure components. It was found that there exist strong intermolecular hydrogen bonding interactions between regenerated wool and CA. Moreover homogeneous surface morphology was observed in the blends with higher CA concentrations. At the final stage of the blending process, the IL solvent was recycled completely. This work presents a green processing route for development of novel natural wool blended materials.     

Enhanced activity and stability of ionic liquid-pretreated lipase

The activity and stability of Mucor javanicus lipase pretreated with various ionic liquids (ILs) were investigated. The results show that the activity and stability of lipase pretreated with ILs were higher than those of untreated lipase for the hydrolysis reaction in an aqueous medium. The activities of lipase pretreated with ILs such as [Bmim][PF₆], [Emim][Tf₂N], [Bmim][BF₄] and [Emim][BF₄] were 1.81, 1.66, 1.56 and 1.60 times higher than that of untreated lipase, respectively. Furthermore, activities of lipase in ILs were well maintained even after 7 days of incubation in ILs at 60 °C, while untreated lipase in phosphate buffer was fully inactivated only after 12 h of incubation at the same temperature. These results suggest that pretreatment of lipase with ILs might form IL-coated lipase which causes the structural change of lipase, and thus, enhances the activity and stability of lipase in aqueous solution.     

Dissolution of cellulose in ionic liquid and water mixtures as revealed by molecular dynamics simulations

Abstract

Increasing population growth and industrialization are continuously oppressing the existing energy resources, elevating the pollution and global fuel demand. Various alternate energy resources can be utilized to cope with these problems in an environment-friendly fashion. Currently, bioethanol (sugarcane, corn-derived) is one of the most widely consumed biofuels in the world. Lignocellulosic biomass is yet another attractive resource for sustainable bioethanol production. Pretreatment step plays a crucial role in the lignocellulose to bioethanol conversion by enhancing cellulose susceptibility to enzymatic hydrolysis. However, economical lignocellulose pretreatment still remains a challenging job. Ionic liquids (ILs), especially 1-ethyl-3-methylimidazolium acetate (EmimAc), is an efficient solvent for cellulose dissolution with improved enzymatic saccharification kinetics. To increase the process efficiency as well as recyclability of IL, water is shown as a compatible cosolvent for lignocellulosic pretreatment. The performance analysis of IL–water mixture based on the molecular level understanding may help to design effective pretreatment solvents. In this study, all-atom molecular dynamics simulation has been performed using EmimAc–water mixtures to understand the behavior of cellulose microcrystal containing eight glucose octamers at room and pretreatment temperatures. High-temperature simulation results show effective cellulose chain separation where cellulose–acetate interaction is found to be the driving force behind dissolution. It is also observed that pretreatment with 50 and 80% IL mixture is efficient in decreasing cellulose crystallinity. At a high IL concentration, water exists in a clustered network which gradually spans into the medium with increasing water fraction leading to loss of its cosolvation activity.

Communicated by Ramaswamy H. Sarma     

Solid acid and microwave-assisted hydrolysis of cellulose in ionic liquid

Solid acid-catalyzed hydrolysis of cellulose in ionic liquid was greatly promoted by microwave heating. H-form zeolites with a lower Si/Al molar ratio and a larger surface area showed a relatively higher catalytic activity. These solid catalysts exhibited better performance than the sulfated ion-exchanging resin NKC-9. Compared with conventional oil bath heating mode, microwave irradiation at an appropriate power significantly reduced the reaction time and increased the yields of reducing sugars. A typical hydrolysis reaction with Avicel cellulose produced glucose in around 37% yield within 8 min.     

Green microwave-assisted synthesis of cellulose/calcium silicate nanocomposites in ionic liquids and recycled ionic liquids

Fabrication of biomass materials by a microwave-assisted method in ionic liquids allows the high value-added applications of biomass by combining three major green chemistry principles: using environmentally preferable solvents, using an environmentally friendly method, and making use of renewable biomass materials. Herein, we report a rapid and green microwave-assisted method for the synthesis of the cellulose/calcium silicate nanocomposites in ionic liquids and recycled ionic liquids. These calcium silicate nanoparticles or nanosheets as prepared were homogeneously dispersed in the cellulose matrix. The experimental results confirm that the ionic liquids can be used repeatedly. Of course, the slight differences were also observed using ionic liquids and recycled ionic liquids. Compared with other conventional methods, the rapid, green, and environmentally friendly microwave-assisted method in ionic liquids opens a new window to the high value-added applications of biomass.     

Acetone-soluble cellulose acetate extracted from waste blended fabrics via ionic liquid catalyzed acetylation

Isolation of cellulose from waste polyester/cotton blended fabrics (WBFs) is a bottleneck for recycling and exploiting waste textiles. The objective of this study was to provide a new environmental-friendly and efficient approach for extracting cellulose derivatives and polyester from WBFs. A Bronsted acidic ionic liquid (IL) N-methyl-imidazolium bisulfate, [Hmim]HSO₄, was used as a novel catalyst for acetylation of cellulose rather than a solvent with the aim to overcome low isolation efficiency associated with the very high viscosity and relatively high costs of ILs. The extraction yield of acetone-soluble cellulose acetate (CA) was 49.3%, which corresponded to a conversion of 84.5% of the cellulose in the original WBFs; meanwhile, 96.2% of the original poly(ethylene terephthalate) (PET) was recovered. The extracted CA was characterized by ¹H NMR, FTIR, XRD and TGA analysis, and the results indicated that high purity acetone-soluble CA and carbohydrate-free PET could be isolated in this manner from WBFs.     

Alkyl-methylimidazolium ionic liquids affect the growth and fermentative metabolism of Clostridium sp

In this study, the effect of ionic liquids, 1-ethyl-3-methylimidazolium acetate [EMIM][Ac], 1-ethyl-3-methylimidazolium diethylphosphate [EMIM][DEP], and 1-methyl-3-methylimidazolium dimethylphosphate [MMIM][DMP] on the growth and glucose fermentation of Clostridium sp. was investigated. Among the three ionic liquids tested, [MMIM][DMP] was found to be least toxic. Growth of Clostridium sp. was not inhibited up to 2.5, 4 and 4 g L⁻¹ of [EMIM][Ac], [EMIM][DEP] and [MMIM][DMP], respectively. [EMIM][Ac] at <2.5 g L⁻¹, showed hormetic effect and stimulated the growth and fermentation by modulating medium pH. Total organic acid production increased in the presence of 2.5 and 2 g L⁻¹ of [EMIM][Ac] and [MMIM][DMP]. Ionic liquids had no significant influence on alcohol production at <2.5 g L⁻¹. Total gas production was affected by ILs at ?2.5 g L⁻¹ and varied with type of methylimidazolium IL. Overall, the results show that the growth and fermentative metabolism of Clostridium sp. is not impacted by ILs at concentrations below 2.5 g L⁻¹.     

Enhanced stability and activity of cellulase in an ionic liquid and the effect of pretreatment on cellulose hydrolysis

We discuss the hydrolysis of cellulose using a pure cellulase: endo-1,4-β-D-glucanase (EG) from the fungus, Aspergillus niger, in buffer, the pure ionic liquid (IL), tris-(2-hydroxyethyl)-methylammonium methylsulfate (HEMA), and various mixtures of the two at different temperatures. Steady-state fluorescence and absorbance studies were performed to monitor the stability and activity of EG using cellulose azure as the substrate. EG attains its highest activity at 45°C in buffer and denatures at ～55°C. On the other hand, HEMA imparts substantial stability to the enzyme, permitting the activity to peak at 75°C. The relative roles of temperature, viscosity, pH, polarity, and the constituent ions of the ILs on the hydrolysis reaction are examined. It is demonstrated that pretreatment of cellulose with ILs such as BMIM Cl, MIM Cl, and HEMA results in more rapid conversion to glucose than hydrolysis with cellulose that is not pretreated. The percent conversion to glucose from pretreated cellulose is increased when the temperature is increased from 45 to 60°C. Two different ILs are used to increase the efficiency of cellulose conversion to glucose. Cellulose is pretreated with BMIM Cl. Subsequent hydrolysis of the pretreated cellulose in 10-20% solutions of HEMA in buffer provides higher yields of glucose at 60°C. Finally, to our knowledge, this is the first study dealing with a pure endoglucanase from commercial A. niger. This enzyme not only shows higher tolerance to ILs, such as HEMA, but also has enhanced thermostability in the presence of the IL.     

Carboxypeptidase A-catalyzed direct conversion of leukotriene C4 to leukotriene F4

Leukotrienes (LTs) are 5-lipoxygenase (5-LO)-derived arachidonic metabolites that constitute a potent set of lipid mediators produced by inflammatory cells. Leukotriene A(4), a labile allylic epoxide formed from arachidonic acid by dual 5-LO activity, is the precursor for LTB(4) and LTC(4) synthesis. LTC(4) is further transformed enzymatically by the sequential action of gamma-glutamyltranspeptidase and dipeptidase to LTD(4) and LTE(4), respectively. In this report, we present evidence that bovine pancreatic carboxypeptidase A (CPA), which shares significant sequence homology with CPA in mast cell granules, catalyzes the conversion of LTC(4) to LTF(4) via the hydrolysis of an amide bond. The identity of CPA-catalyzed LTC(4) hydrolysis product as LTF(4) was confirmed by several analytical criteria, including enzymatic conversion to conjugated tetraene by soybean LO, conversion to LTE(4) by gamma-glutamyltranspeptidase, cochromatography with the standard LTF(4) and positive-ion fast-atom bombardment mass spectral analysis. Thus, it appears that the physiological significance of this single-step transformation may point toward a major cellular homeostatic mechanism of metabolizing LTC(4), a potent bronco- and vasoconstrictor, to a less potent form of cysteinyl LTs.     

Clean conversion of cellulose into fermentable glucose

We studied the process of conversion of microcrystalline-cellulose into fermentable glucose in the formic acid reaction system using cross polarization/magic angle spinning ¹³C-nuclear magnetic resonance, X-ray diffraction and Fourier transform infrared spectroscopy. The results indicated that formic acid as an active agent was able to effectively penetrate into the interior space of the cellulose molecules, thus collapsing the rigid crystalline structure and allowing hydrolysis to occur easily in the amorphous zone as well as in the crystalline zone. The microcrystalline-cellulose was hydrolyzed using formic acid and 4% hydrochloric acid under mild conditions. The effects of hydrochloric acid concentration, the ratio of solid to liquid, temperature (55–75 °C) and retention time (0–9 h), and the concentration of glucose were analyzed. The hydrolysis velocities of microcrystalline-cellulose were 6.14 × 10^− 3 h^− 1 at 55 °C, 2.94 × 10^− 2 h^− 1 at 65 °C, and 6.84 × 10^− 2 h^− 1 at 75 °C. The degradation velocities of glucose were 0.01 h^− 1 at 55 °C, 0.14 h^− 1 at 65 °C, 0.34 h^− 1 at 75 °C. The activation energy of microcrystalline-cellulose hydrolysis was 105.61 kJ/mol, and the activation energy of glucose degradation was 131.37 kJ/mol.     

NMR evidence of hydrogen bonding in 1-ethyl-3-methylimidazolium-tetrafluoroborate room temperature ionic liquid

The 1-ethyl-3-methylimidazolium-tetrafluoroborate (EMI–BF₄) room temperature ionic liquid was investigated with NMR techniques. Diffusion coefficients measured at temperatures ranging from 300 to 360 K indicate that phase-change occurred in the vicinity of 333 K, which is supported by ¹¹B quadrupolar relaxation rates. This phase change is ascribed to the transformation of the diffusion particle from ‘discrete ion-pair’ to ‘individual ion’ at temperatures above 335 K due to decomposition of the EMI–BF₄ ion pair. Analysis of the ¹³C dipole–dipole relaxation rates identifies the formation of hydrogen bond (C2HF) between the counterions, EMI⁺ and BF₄ ⁻. This hydrogen bonding may have significant contribution to the higher viscosity of this ionic liquid in comparison with the EMI–AlCl₄ ionic liquid at corresponding temperatures.