Subject-specific hip geometry and hip joint centre location affects calculated contact forces at the hip during gait

Hip loading affects the development of hip osteoarthritis, bone remodelling and osseointegration of implants. In this study, we analyzed the effect of subject-specific modelling of hip geometry and hip joint centre (HJC) location on the quantification of hip joint moments, muscle moments and hip contact forces during gait, using musculoskeletal modelling, inverse dynamic analysis and static optimization. For 10 subjects, hip joint moments, muscle moments and hip loading in terms of magnitude and orientation were quantified using three different model types, each including a different amount of subject-specific detail: (1) a generic scaled musculoskeletal model, (2) a generic scaled musculoskeletal model with subject-specific hip geometry (femoral anteversion, neck-length and neck-shaft angle) and (3) a generic scaled musculoskeletal model with subject-specific hip geometry including HJC location. Subject-specific geometry and HJC location were derived from CT. Significant differences were found between the three model types in HJC location, hip flexion–extension moment and inclination angle of the total contact force in the frontal plane. No model agreement was found between the three model types for the calculation of contact forces in terms of magnitude and orientations, and muscle moments. Therefore, we suggest that personalized models with individualized hip joint geometry and HJC location should be used for the quantification of hip loading. For biomechanical analyses aiming to understand modified hip joint loading, and planning hip surgery in patients with osteoarthritis, the amount of subject-specific detail, related to bone geometry and joint centre location in the musculoskeletal models used, needs to be considered.     

Computed tomography-based joint locations affect calculation of joint moments during gait when compared to scaling approaches

Hip joint moments are an important parameter in the biomechanical evaluation of orthopaedic surgery. Joint moments are generally calculated using scaled generic musculoskeletal models. However, due to anatomical variability or pathology, such models may differ from the patient's anatomy, calling into question the accuracy of the resulting joint moments. This study aimed to quantify the potential joint moment errors caused by geometrical inaccuracies in scaled models, during gait, for eight test subjects. For comparison, a semi-automatic computed tomography (CT)-based workflow was introduced to create models with subject-specific joint locations and inertial parameters. 3D surface models of the femora and hemipelves were created by segmentation and the hip joint centres and knee axes were located in these models. The scaled models systematically located the hip joint centre (HJC) up to 33.6 mm too inferiorly. As a consequence, significant and substantial peak hip extension and abduction moment differences were recorded, with, respectively, up to 23.1% and 15.8% higher values in the image-based models. These findings reaffirm the importance of accurate HJC estimation, which may be achieved using CT- or radiography-based subject-specific modelling. However, obesity-related gait analysis marker placement errors may have influenced these results and more research is needed to overcome these artefacts.     

Subject-specific geometrical detail rather than cost function formulation affects hip loading calculation*

This study assessed the relative importance of introducing an increasing level of medical image-based subject-specific detail in bone and muscle geometry in the musculoskeletal model, on calculated hip contact forces during gait. These forces were compared to introducing minimization of hip contact forces in the optimization criterion. With an increasing level of subject-specific detail, specifically MRI-based geometry and wrapping surfaces representing the hip capsule, hip contact forces decreased and were more comparable to contact forces measured using instrumented prostheses (average difference of 0.69 BW at the first peak compared to 1.04 BW for the generic model). Inclusion of subject-specific wrapping surfaces in the model had a greater effect than altering the cost function definition.     

Non-rigid deformation to include subject-specific detail in musculoskeletal models of CP children with proximal femoral deformity and its effect on muscle and contact forces during gait

To account for proximal femoral deformities in children with cerebral palsy (CP), subject-specific musculoskeletal models are needed. Non-rigid deformation (NRD) deforms generic onto personalized bone geometry and thereby transforms the muscle points. The goal of this study was to determine to what extent the models and simulation outcomes in CP patients differ when including subject-specific detail using NRD or Magnetic Resonance Imaging (MRI)-based models. The NRD models slightly overestimated hip contact forces compared to MRI models and differences in muscle point positions and moment arm lengths (MALs) remained, although differences were smaller than for the generic model.     

Atlas-based non-rigid image registration to automatically define line-of-action muscle models: A validation study

Research has raised a growing concern about the accuracy of rescaled generic musculoskeletal models for estimating a subject's musculoskeletal geometry. Information extracted from magnetic resonance (MR) images can improve the subject-specific detail and accuracy of musculoskeletal models. Nevertheless, methods that allow efficient, automated definition of subject-specific muscular models for use in biomechanical analysis of gait have not yet been published to the best of our knowledge. We report a novel method for automated definition of subject-specific muscle paths using non-rigid image registration between an atlas image and the subject's MR images. We validated this approach quantitatively by measuring the distance between automatically and manually defined coordinates of muscle attachment sites. Data was collected for 34 muscles in each lower limb of 5 paediatric subjects diagnosed with diplegic cerebral palsy and presenting varying degrees of increased femoral anteversion. Distances showed an overall median Euclidean error of 6.1 mm: 2.0 mm along the medio-lateral direction, 1.8 mm along the anterior–posterior direction and 3.8 mm along the superior–inferior direction. A qualitative validation between automatically defined muscle points and the muscular geometry observed in the subject's medical image data corroborated the quantitative validation. This automated approach followed by visual inspection and, if needed, correction to the muscle paths, reduced the time required for defining 34 lower-limb muscle paths from around 3.5 to 1 h. Furthermore, the method was also applicable to aberrant skeletal geometry. Using the proposed method, defining MR-based musculoskeletal models becomes a time efficient and more accurate alternative to rescaling generic models.     

Subject-specific geometry affects acetabular contact pressure during gait more than subject-specific loading patterns

Abstract

Finite element modeling (FEM) can predict hip cartilage contact mechanics. This study investigated how subject-specific boundary conditions and joint geometry affect acetabular cartilage contact mechanics using a multi-scale workflow. For two healthy subjects, musculoskeletal models calculated subject-specific hip kinematics and loading, which were used as boundary conditions for FEM. Cartilage contact mechanics were predicted using either generic or subject-specific FEM and boundary conditions. A subject-specific mesh resulted in a more lateral contact. Effects of subject-specific boundary conditions varied between both subjects. Results highlight the complex interplay between loading and kinematics and their effect on cartilage contact mechanics.     

Subject-specific hip geometry affects predicted hip joint contact forces during gait

Hip loading affects bone remodeling and implant fixation. In this study, we have analyzed the effect of subject-specific modeling of hip geometry on muscle activation patterns and hip contact forces during gait, using musculoskeletal modeling, inverse dynamic analysis and static optimization. We first used sensitivity analysis to analyze the effect of isolated changes in femoral neck-length (NL) and neck-shaft angle (NSA) on calculated muscle activations and hip contact force during the stance phase of gait. A deformable generic musculoskeletal model was adjusted incrementally to adopt a physiological range of NL and NSA. In a second similar analysis, we adjusted hip geometry to the measurements from digitized radiographs of 20 subjects with primary hip osteoarthrosis. Finally, we studied the effect of hip abductor weakness on muscle activation patterns and hip contact force. This analysis showed that differences in NL (41-74 mm) and NSA (113-140 degrees ) affect the muscle activation of the hip abductors during stance phase and hence hip contact force by up to three times body weight. In conclusion, the results from both the sensitivity and subject-specific analysis showed that at the moment of peak contact force, altered NSA has only a minor effect on the loading configuration of the hip. Increased NL, however, results in an increase of the three hip contact-force components and a reduced vertical loading. The results of these analyses are essential to understand modified hip joint loading, and for planning hip surgery for patients with osteoarthrosis.     

Evaluation of a method to scale muscle strength for gait simulations of children with cerebral palsy

Cerebral palsy (CP) is a neurological disorder that results in life-long mobility impairments. Musculoskeletal models used to investigate mobility deficits for children with CP often lack subject-specific characteristics such as altered muscle strength, despite a high prevalence of muscle weakness in this population. We hypothesized that incorporating subject-specific strength scaling within musculoskeletal models of children with CP would improve accuracy of muscle excitation predictions in walking simulations. Ten children (13.5 ± 3.3 years; GMFCS level II) with spastic CP participated in a gait analysis session where lower-limb kinematics, ground reaction forces, and bilateral electromyography (EMG) of five lower-limb muscles were collected. Isometric strength was measured for each child using handheld dynamometry. Three musculoskeletal models were generated for each child including a ‘Default’ model with the generic musculoskeletal model’s muscle strength, a ‘Uniform’ model with muscle strength scaled allometrically, and a ‘Custom’ model with muscle strength scaled based on handheld dynamometry strength measures. Muscle-driven gait simulations were generated using each model for each child. Simulation accuracy was evaluated by comparing predicted muscle excitations and measured EMG signals, both in the duration of muscle activity and the root-mean-square difference (RMSD) between signals. Improved agreement with EMG were found in both the ‘Custom’ and ‘Uniform’ models compared to the ‘Default’ model indicated by improvement in RMSD summed across all muscles, as well as RMSD and duration of activity for individual muscles. Incorporating strength scaling into musculoskeletal models can improve the accuracy of walking simulations for children with CP.     

Subject-specific tendon-aponeurosis definition in hill-type model predicts higher muscle forces in dynamic tasks

Neuromusculoskeletal models are a common method to estimate muscle forces. Developing accurate neuromusculoskeletal models is a challenging task due to the complexity of the system and large inter-subject variability. The estimation of muscles force is based on the mechanical properties of tendon-aponeurosis complex. Most neuromusculoskeletal models use a generic definition of the tendon-aponeurosis complex based on in vitro test, perhaps limiting their validity. Ultrasonography allows subject-specific estimates of the tendon-aponeurosis complex's mechanical properties. The aim of this study was to investigate the influence of subject-specific mechanical properties of the tendon-aponeurosis complex on a neuromusculoskeletal model of the ankle joint. Seven subjects performed isometric contractions from which the tendon-aponeurosis force-strain relationship was estimated. Hopping and running tasks were performed and muscle forces were estimated using subject-specific tendon-aponeurosis and generic tendon properties. Two ultrasound probes positioned over the muscle-tendon junction and the mid-belly were combined with motion capture to estimate the in vivo tendon and aponeurosis strain of the medial head of gastrocnemius muscle. The tendon-aponeurosis force-strain relationship was scaled for the other ankle muscles based on tendon and aponeurosis length of each muscle measured by ultrasonography. The EMG-driven model was calibrated twice - using the generic tendon definition and a subject-specific tendon-aponeurosis force-strain definition. The use of subject-specific tendon-aponeurosis definition leads to a higher muscle force estimate for the soleus muscle and the plantar-flexor group, and to a better model prediction of the ankle joint moment compared to the model estimate which used a generic definition. Furthermore, the subject-specific tendon-aponeurosis definition leads to a decoupling behaviour between the muscle fibre and muscle-tendon unit in agreement with previous experiments using ultrasonography. These results indicate the use of subject-specific tendon-aponeurosis definitions in a neuromusculoskeletal model produce better agreement with measured external loads and more physiological model behaviour.     

Comparative assessment of bone pose estimation using Point Cluster Technique and OpenSim

Estimating the position of the bones from optical motion capture data is a challenge associated with human movement analysis. Bone pose estimation techniques such as the Point Cluster Technique (PCT) and simulations of movement through software packages such as OpenSim are used to minimize soft tissue artifact and estimate skeletal position; however, using different methods for analysis may produce differing kinematic results which could lead to differences in clinical interpretation such as a misclassification of normal or pathological gait. This study evaluated the differences present in knee joint kinematics as a result of calculating joint angles using various techniques. We calculated knee joint kinematics from experimental gait data using the standard PCT, the least squares approach in OpenSim applied to experimental marker data, and the least squares approach in OpenSim applied to the results of the PCT algorithm. Maximum and resultant RMS differences in knee angles were calculated between all techniques. We observed differences in flexion/extension, varus/valgus, and internal/external rotation angles between all approaches. The largest differences were between the PCT results and all results calculated using OpenSim. The RMS differences averaged nearly 5° for flexion/extension angles with maximum differences exceeding 15°. Average RMS differences were relatively small (< 1.08°) between results calculated within OpenSim, suggesting that the choice of marker weighting is not critical to the results of the least squares inverse kinematics calculations. The largest difference between techniques appeared to be a constant offset between the PCT and all OpenSim results, which may be due to differences in the definition of anatomical reference frames, scaling of musculoskeletal models, and/or placement of virtual markers within OpenSim. Different methods for data analysis can produce largely different kinematic results, which could lead to the misclassification of normal or pathological gait. Improved techniques to allow non-uniform scaling of generic models to more accurately reflect subject-specific bone geometries and anatomical reference frames may reduce differences between bone pose estimation techniques and allow for comparison across gait analysis platforms.     

Are Subject-Specific Musculoskeletal Models Robust to the Uncertainties in Parameter Identification?

Subject-specific musculoskeletal modeling can be applied to study musculoskeletal disorders, allowing inclusion of personalized anatomy and properties. Independent of the tools used for model creation, there are unavoidable uncertainties associated with parameter identification, whose effect on model predictions is still not fully understood. The aim of the present study was to analyze the sensitivity of subject-specific model predictions (i.e., joint angles, joint moments, muscle and joint contact forces) during walking to the uncertainties in the identification of body landmark positions, maximum muscle tension and musculotendon geometry. To this aim, we created an MRI-based musculoskeletal model of the lower limbs, defined as a 7-segment, 10-degree-of-freedom articulated linkage, actuated by 84 musculotendon units. We then performed a Monte-Carlo probabilistic analysis perturbing model parameters according to their uncertainty, and solving a typical inverse dynamics and static optimization problem using 500 models that included the different sets of perturbed variable values. Model creation and gait simulations were performed by using freely available software that we developed to standardize the process of model creation, integrate with OpenSim and create probabilistic simulations of movement. The uncertainties in input variables had a moderate effect on model predictions, as muscle and joint contact forces showed maximum standard deviation of 0.3 times body-weight and maximum range of 2.1 times body-weight. In addition, the output variables significantly correlated with few input variables (up to 7 out of 312) across the gait cycle, including the geometry definition of larger muscles and the maximum muscle tension in limited gait portions. Although we found subject-specific models not markedly sensitive to parameter identification, researchers should be aware of the model precision in relation to the intended application. In fact, force predictions could be affected by an uncertainty in the same order of magnitude of its value, although this condition has low probability to occur.     

Validation of subject-specific musculoskeletal models using the anatomical reachable 3-D workspace

A novel metric for the validation of musculoskeletal models is proposed, the reachable 3-D workspace (RWS). This new metric was used to compare a generic model scaled in a standard manner to a more subject-specific model. An experimental protocol for assessing the RWS was performed by ten participants for four distinct hand-payload cases. In addition, isometric individual strength measurements were collected for 12 different directions. The strength of subject-specific musculoskeletal models was then computed using the following assumptions: (1) standard routines including the length-mass-fat (LMF) scaling law; (2) the isometric strengths of the muscle elements were optimized to the individual strength measurements using joint strength factors (JSF). The RWS of each participant was subsequently estimated from each of the scaling approaches, LMF and JSF, for the four load cases. The experimental RWS showed that the volume and shape decreased with increasing hand-payload for every participant. The lateral and frontal far-from-torso aspects of the RWS were reduced the most. These trends were reproduced by both strength scaling approaches, but the LMF-scaled models were not able to track the overall RWS volume decrease with increasing payload, since they proved to be weaker than the participants. On the other hand, the optimised JSF subject-specific models performed better on the prediction of the RWS for all payload cases across participants. The RWS can potentially be further used as a subject-specific musculoskeletal model validation, enabling quantification of the volume and shape differences between experimentally and model-predicted RWSs.     

Using two palpable measurements improves the subject-specific femoral modeling

Subject-specific musculoskeletal models are essential to biomedical research and clinical applications, such as customized joint replacement, computer-aided surgical planning, gait analysis and automated segmentation. Generating these models from CT or magnetic resonance imaging (MRI) is time and resource intensive, requiring special skills. Therefore, in many studies individual bone models are approximated by scaling a generic template. Thus, the primary goal of this study was to determine a set of clinically available parameters (palpable measures and demographic data) that could improve the prediction of femoral dimensions, as compared to predicting these variables using uniform scaling based on palpable length. Similar to previous non-homogenous anthropometric scaling methods, the non-homogenous scaling method proposed in this study improved the prediction over uniform scaling of five key femoral measures. Homogenous scaling forces all dimensions of an object to be scaled equally, whereas non-homogenous scaling allows the dimensions to be scaled independently. The largest improvement was in femoral depth, where the coefficient of determination (r²) improved from 0.22 (homogenous) to 0.60 (non-homogeneous). In general, the major advantage of this non-homogenous scaling method is its ability to support the accurate and rapid generation of subject-specific femoral models since all parameters can be collected clinically, without imaging or invasive methods.     

Can a reduction approach predict reliable joint contact and musculo-tendon forces?

Musculoskeletal models generally solve the muscular redundancy by numerical optimisation. They have been extensively validated using instrumented implants. Conversely, a reduction approach considers only one flexor or extensor muscle group at the time to equilibrate the inter-segmental joint moment. It is not clear if such models can still predict reliable joint contact and musculo-tendon forces during gait.Tibiofemoral contact force and gastrocnemii, quadriceps, and hamstrings musculo-tendon forces were estimated using a reduction approach for five subjects walking with an instrumented prosthesis. The errors in the proximal-distal tibiofemoral contact force fell in the range (0.3–0.9 body weight) reported in the literature for musculoskeletal models using numerical optimisation. The musculo-tendon forces were in agreement with the EMG envelops and appeared comparable to the ones reported in the literature with generic musculoskeletal models.Although evident simplifications and limitations, it seems that the reduction approach can provided quite reliable results. It can be a useful pedagogical tool in biomechanics, e.g. to illustrate the theoretical differences between inter-segmental and contact forces, and can provide a first estimate of the joint loadings in subjects with limited musculoskeletal deformities and neurological disorders.     

Knee medial and lateral contact forces in a musculoskeletal model with subject-specific contact point trajectories

Contact point (CP) trajectory is a crucial parameter in estimating medial/lateral tibio-femoral contact forces from the musculoskeletal (MSK) models. The objective of the present study was to develop a method to incorporate the subject-specific CP trajectories into the MSK model. Ten healthy subjects performed 45 s treadmill gait trials. The subject-specific CP trajectories were constructed on the tibia and femur as a function of extension-flexion using low-dose bi-plane X-ray images during a quasi-static squat. At each extension-flexion position, the tibia and femur CPs were superimposed in the three directions on the medial side, and in the anterior-posterior and proximal-distal directions on the lateral side to form the five kinematic constraints of the knee joint. The Lagrange multipliers associated to these constraints directly yielded the medial/lateral contact forces. The results from the personalized CP trajectory model were compared against the linear CP trajectory and sphere-on-plane CP trajectory models which were adapted from the commonly used MSK models. Changing the CP trajectory had a remarkable impact on the knee kinematics and changed the medial and lateral contact forces by 1.03 BW and 0.65 BW respectively, in certain subjects. The direction and magnitude of the medial/lateral contact force were highly variable among the subjects and the medial-lateral shift of the CPs alone could not determine the increase/decrease pattern of the contact forces. The suggested kinematic constraints are adaptable to the CP trajectories derived from a variety of joint models and those experimentally measured from the 3D imaging techniques.     

A musculoskeletal foot model for clinical gait analysis

Several full body musculoskeletal models have been developed for research applications and these models may potentially be developed into useful clinical tools to assess gait pathologies. Existing full-body musculoskeletal models treat the foot as a single segment and ignore the motions of the intrinsic joints of the foot. This assumption limits the use of such models in clinical cases with significant foot deformities. Therefore, a three-segment musculoskeletal model of the foot was developed to match the segmentation of a recently developed multi-segment kinematic foot model. All the muscles and ligaments of the foot spanning the modeled joints were included. Muscle pathways were adjusted with an optimization routine to minimize the difference between the muscle flexion–extension moment arms from the model and moment arms reported in literature. The model was driven by walking data from five normal pediatric subjects (aged 10.6±1.57 years) and muscle forces and activation levels required to produce joint motions were calculated using an inverse dynamic analysis approach. Due to the close proximity of markers on the foot, small marker placement error during motion data collection may lead to significant differences in musculoskeletal model outcomes. Therefore, an optimization routine was developed to enforce joint constraints, optimally scale each segment length and adjust marker positions. To evaluate the model outcomes, the muscle activation patterns during walking were compared with electromyography (EMG) activation patterns reported in the literature. Model-generated muscle activation patterns were observed to be similar to the EMG activation patterns.     

Subject-specific musculoskeletal model of the lower limb in a lying and standing position

Accurate estimation of joint loads implies using subject-specific musculoskeletal models. Moreover, as the lines of action of the muscles are dictated by the soft tissues, which are in turn influenced by gravitational forces, we developed a method to build subject-specific models of the lower limb in a functional standing position. Bones and skin envelope were obtained in a standing position, whereas muscles and a set of bony landmarks were obtained from conventional magnetic resonance images in a lying position. These muscles were merged with the subject-specific skeletal model using a nonlinear transformation, taking into account soft tissue movements and gravitational effects. Seven asymptomatic lower limbs were modelled using this method, and results showed realistic deformations. Comparing the subject-specific skeletal model to a scaled reference model rendered differences in terms of muscle length up to 4% and in terms of moment arm for adductor muscles up to 30%. These preliminary findings enlightened the importance of subject-specific modelling in a functional position.     

Muscle force estimation in clinical gait analysis using AnyBody and OpenSim

A variety of musculoskeletal models are applied in different modelling environments for estimating muscle forces during gait. Influence of different modelling assumptions and approaches on model outputs are still not fully understood, while direct comparisons of standard approaches have been rarely undertaken. This study seeks to compare joint kinematics, joint kinetics and estimated muscle forces of two standard approaches offered in two different modelling environments (AnyBody, OpenSim). It is hypothesised that distinctive differences exist for individual muscles, while summing up synergists show general agreement. Experimental data of 10 healthy participants (28 ± 5 years, 1.72 ± 0.08 m, 69 ± 12 kg) was used for a standard static optimisation muscle force estimation routine in AnyBody and OpenSim while using two gait-specific musculoskeletal models. Statistical parameter mapping paired t-test was used to compare joint angle, moment and muscle force waveforms in Matlab. Results showed differences especially in sagittal ankle and hip angles as well as sagittal knee moments. Differences were also found for some of the muscles, especially of the triceps surae group and the biceps femoris short head, which occur as a result of different anthropometric and anatomical definitions (mass and inertia of segments, muscle properties) and scaling procedures (static vs. dynamic). Understanding these differences and their cause is crucial to operate such modelling environments in a clinical setting. Future research should focus on alternatives to classical generic musculoskeletal models (e.g. implementation of functional calibration tasks), while using experimental data reflecting normal and pathological gait to gain a better understanding of variations and divergent behaviour between approaches.     

Musculotendon parameters and musculoskeletal pathways within the human foot

In order to create a flexible model of the foot for dynamic musculoskeletal models, anthropometric data combined with geometric information describing the intrinsic musculature are needed. In this study, the left feet of two male and two female cadavers were dissected to expose the intrinsic musculotendon pathways. Three-dimensional coordinates of bony landmarks, tendon origins, insertions, and via points were digitized to submillimeter accuracy. Muscle architectural parameters were also measured, including volume, weight, and pennation angle and sarcomere, fascicle, and free tendon lengths. Optimal muscle fascicle lengths, pen-nation angles at optimal length, physiological cross-sectional areas (PCSA), and tendon slack lengths were calculated from the directly measured values. Fascicle length and pennation angle varied greatly within each subject. Average fascicle lengths normalized by optimal fascicle length varied between 0.73 and 1.25, with 75% of the formalin-preserved muscles being found in a shortened state. The muscle volume and PCSA also had a large variability within subjects but less variation between subjects. The ratio of tendon slack length to optimal fascicle length was found to vary between 1.05 and 9.56. Using this data, a deformable model of the foot can now be created. It is envisioned that deformable feet will significantly improve stability and realism in models of gait, posture, and sporting activities.     

Gait stride-to-stride variability and foot clearance pattern analysis in Idiopathic Parkinson’s Disease and Vascular Parkinsonism

The literature on gait analysis in Vascular Parkinsonism (VaP), addressing issues such as variability, foot clearance patterns, and the effect of levodopa, is scarce. This study investigates whether spatiotemporal, foot clearance and stride-to-stride variability analysis can discriminate VaP, and responsiveness to levodopa.Fifteen healthy subjects, 15 Idiopathic Parkinson's Disease (IPD) patients and 15 VaP patients, were assessed in two phases: before (Off-state), and one hour after (On-state) the acute administration of a suprathreshold (1.5 times the usual) levodopa dose. Participants were asked to walk a 30-meter continuous course at a self-selected walking speed while wearing foot-worn inertial sensors. For each gait variable, mean, coefficient of variation (CV), and standard deviations SD1 and SD2 obtained by Poincaré analysis were calculated. General linear models (GLMs) were used to identify group differences. Patients were subject to neuropsychological evaluation (MoCA test) and Brain MRI.VaP patients presented lower mean stride velocity, stride length, lift-off and strike angle, and height of maximum toe (later swing) (p < .05), and higher %gait cycle in double support, with only the latter unresponsive to levodopa. VaP patients also presented higher CV, significantly reduced after levodopa. Yet, all VaP versus IPD differences lost significance when accounting for mean stride length as a covariate.In conclusion, VaP patients presented a unique gait with reduced degrees of foot clearance, probably correlated to vascular lesioning in dopaminergic/non-dopaminergic cortical and subcortical non-dopaminergic networks, still amenable to benefit from levodopa. The dependency of gait and foot clearance and variability deficits from stride length deserves future clarification.