Development of an optical sensor for chlortetracycline detection based on the fluorescence quenching of l‐tryptophan

A simple and selective spectrofluorimetric method for the detection of chlortetracycline (CTC) was studied. In pH 7.4 buffer medium l ‐tryptophan (l ‐Trp), applied as the fluorescence probe, interacted with CTC resulting in fluorescence quenching of the probe. CTC was detected with maximum excitation and emission wavelengths at λ_ex/λ_em = 275/350 nm. Notably, quenching of fluorescence intensities was positively proportional to the CTC concentration over the range of 0.65–30 μmol L^?1 and the limit of detection was 0.2 μmol L^?1. Effect of temperature shown in Stern?Volmer plots, absorption spectra and fluorescence lifetime determination, indicated that fluorescence quenching of l ‐Trp by CTC was mainly by static quenching. The proposed study used practical samples analysis satisfactorily.     

Fluorescence‐based sensor for selective and sensitive detection of amoxicillin (Amox) in aqueous medium: Application to pharmaceutical and biomedical analysis

We here for the first time demonstrate an analytical approach for the highly selective and sensitive detection of amoxicillin (Amox) in aqueous medium based on the fluorescence quenching of quantum dots (QDs). The change in fluorescence intensity of mercaptopropionic acid‐capped cadmium sulphide (MPA‐CdS) QDs is attributed to the increasing concentration of Amox. The results show that the fluorescence quenching of QDs by Amox takes place through both static and dynamic types of quenching mechanism. The fluorescence quenching of QDs with increase in concentration of Amox shows the linear range between 5 μg ml^?1 and 30 μg ml^?1 and the limit of detection (LOD) is 5.19 μg ml^?1. There is no interference of excipients, which are commonly present in pharmaceutical formulation and urine samples. For the practical application approach, the developed method has been successfully applied for the determination of Amox in pharmaceutical formulations and urine samples with acceptable results.     

Silver nanoclusters stabilized with denatured fish sperm DNA and the application on trace mercury ions detection

In this study, fluorescent silver nanoclusters (Ag NCs) were synthesized using denatured fish sperm DNA as the template. In contrast to other methods, this method did not use artificial DNA as the template. After their reaction with denatured fish sperm DNA, Ag⁺ ions were reduced by NaBH₄ to form Ag NCs. The Ag NCs showed a strong fluorescence emission at 650 nm when excited at 585 nm. The fluorescence intensity increased fourfold at pH 3.78, controlled with Britton–Robinson buffer solution. The fluorescence of the Ag NCs was quenched in the presence of trace mercury ions (Hg²⁺) in a weakly acidic medium and nitrogen atmosphere. The extent of the fluorescence quenching of Ag NCs strongly depends on the Hg²⁺ ion concentration over a linear range from 2.0 nmol L^?1 to 3.0 μmol L^?1. The detection limit (3σ/k) for Hg²⁺ was 0.7 nmol L^?1. Thus, a sensitive and rapid method was developed for the detection of Hg²⁺ ions.     

A sensitive method for determination of trace amounts of chromate (III) with terbium (III) sodium hexametaphosphate chelate as fluorescent probe

Based on the fluorescence quenching of Terbium (III)‐sodium hexametaphosphate (Tb/SHMP) chelates in the presence chromate (III), a sensitive fluorimetric method was developed for the determination of trace amounts of chromium (III) in aqueous solutions. Under the optimum conditions, the linear calibration graph was obtained (R = 0.996). The linear range and detection limit of Cr (III) were 7.69 × 10^?7 to 1.15 × 10^?4 mol L^?1 and 4.50 × 10^?7 mol L^?1, respectively. The proposed method had a wider linear range and was proved to be very sensitive, rapid and simple. The method was applied successfully to the determination of chromium (III) in the synthetic samples and real water samples. Moreover, the reaction mechanism was discussed through the fluorescence lifetime and proved to be dynamic quenching behavior. Copyright © 2010 John Wiley & Sons, Ltd.     

Optical ascorbic acid sensor based on the fluorescence quenching of silver nanoparticles

A sensitive and selective fluorimetric sensor for the assay of ascorbic acid (AA) using silver nanoparticles as emission reagent was investigated. In this study, silver nanoparticles were prepared based on aqueous–gaseous phase reaction of silver nitrate solution and ammonia gas. The nanoparticles were water‐soluble, stable and had a narrow emission band. They were used as a fluorescence probe for the assay of ascorbic acid on its quenching effect on the emission of silver nanoparticles. The principal reason for quenching is likely to be a complexation between ascorbic acid and silver nanoparticles. The quenching mechanism was established by Stern–Volmer law. Under the optimum conditions, the quenched fluorescence intensity was linear with the concentration of ascorbic acid in the range of 4.1 × 10^?6 to 1.0 ×10^?4 m (r = 0.9985) with a detection limit of 1.0 × 10^?7 m . The RSD for repeatability of the sensor for the assay of ascorbic acid concentration of 3.0 × 10^?5 and 4.0 × 10^?6 m was found to be 1.5 and 1.3%, respectively. The proposed method was applied to the determination of ascorbic acid in vegetables and vitamin C tablets. Copyright © 2009 John Wiley & Sons, Ltd.     

A selective and sensitive fluorescent sensor for cysteine detection based on bi‐8‐carboxamidoquinoline derivative and Cu2+ complex

In this paper, a novel fluorescent sensor 1 for selective and sensitive detection of cysteine was developed based on a complex between bi‐8‐carboxamidoquinoline derivative ligand ( L ) and Cu²⁺. The interaction of Cu²⁺ with the ligand causes a dramatic fluorescence quenching most likely due to its high affinity towards Cu²⁺ and a ligand–metal charge transfer (LMCT) process. The in situ generated L–Cu ² complex was utilized as a chemosensing ensemble for cysteine. In the presence of cysteine, the fluorophore, L , was released from L–Cu ² complex because of the strong affinity of cysteine to Cu²⁺ via the Cu–S bond, leading to the fluorescence recovery of the ligand. The proposed displacement mechanism was confirmed by the results of mass spectrometry (MS) study. Under optimized conditions, the recovered fluorescence intensity is linear with cysteine concentrations in the range 1 × 10^?6 mol/l to 8 × 10^?6 mol/l. The detection limit for cysteine is 1.92 × 10^?7 mol/l. Furthermore, the established method showed a highly sensitive and selective response to cysteine among the 20 fundamental α‐amino acids used as the building blocks of proteins, after Ni²⁺ was used as a masking agent to eliminate the interference of His. The proposed sensor is applicable in monitoring cysteine in practical samples with good recovery rate.     

β‐Cyclodextrin protected Cu nanoclusters as a novel fluorescence sensor for graphene oxide in environmental water samples

This paper proposed a simple and sensitive approach for detecting graphene oxide (GO) in a wide pH range in environmental water samples using fluorescent β‐CD protected Cu NCs based on the hydrogen‐bond interactions between GO and 6‐SH‐β‐CD. The influences of dilution ratio and pH were investigated. We found that the fluorescence quenching efficiency of Cu NCs by GO remained almost the same under pH from 4 to 10, which benefitted the monitoring of GO under different pH conditions in real samples. The fluorescence quenching mechanism was also discussed. The fluorescence of β‐CD protected Cu NCs could be quenched in the presence of GO with a lowest detection concentration of 0.1 mg·L^?1. Good linear correlations were obtained over the concentration range from 0 to 30 mg·L^?1 at different pH values (pH = 4, pH = 7 and pH = 12). In addition, this method was successfully applied to the determination of GO in real samples which presents more opportunities for application in environmental and material sciences.     

A fluorescent probe for biothiols based on the conjugate addition of thiols to α,β‐unsaturated ester

A sensitive fluorogenic probe 1 for biothiols was developed based on the Michael addition reaction. The probe 1 was readily synthesized via the reaction of 2‐(4′‐hydroxyphenyl) benzimidazole (HPBI) with acryloyl chloride and shows weak fluorescence emission. Upon mixing with biothiols, the fluorescence of 1 is significantly enhanced due to the conjugate addition of thiols to the α,β‐unsaturated carbonyl moiety, thus eliminating the photoinduced electron transfer (PET) quenching of the fluorophore by the intramolecular carbon–carbon double bond. Cysteine (Cys) was selected as the representative thiol in the spectral experiment. A good linear relationship was obtained from 1.0 to 30.0 µmol L^?1 for Cys and the detection limit was 0.17 µmol L^?1. Furthermore, probe 1 was highly selective for biothiols without the interference of some biologically relevant analytes and has been applied to detecting biothiols in human urine samples. Copyright © 2010 John Wiley & Sons, Ltd.     

Fluorescence spectrometric study on the interaction of tamibarotene with bovine serum albumin

The interaction between tamibarotene and bovine serum albumin (BSA) was studied using fluorescence quenching technique and ultraviolet–visible spectrophotometry. The results of experiments showed that tamibarotene could strongly quench the intrinsic fluorescence of BSA by a dynamic quenching mechanism. The apparent binding constant, number of binding site and corresponding thermodynamic parameters at different temperatures were calculated respectively, and the main interaction force between tamibarotene and BSA was proved to be hydrophobic force. Synchronous fluorescence spectra showed that tamibarotene changed the molecular conformation of BSA. When BSA concentration was 1.00 × 10^?6 mol L^?1, the quenched fluorescence ΔF had a good linear relationship with the concentration of tamibarotene in the range 1.00 × 10^?6 to 12.00 × 10^?6 mol L^?1 with the detection limit of 6.52 × 10^?7 mol L^?1. Copyright © 2010 John Wiley & Sons, Ltd.     

Construction of a novel turn‐on–off fluorescence sensor used for highly selective detection of thiamine via its quenching effect on o‐phen‐Zn2+ complex

In this work, a simple and selective fluorescence sensor approach called ‘turn‐on–off’ for the determination of thiamine (TM) has been developed. As known, the o‐phenanthroline (o‐phen) has inner fluorescence, though when reacted with zinc ions to form the o‐phen–Zn²⁺ complex the fluorescence intensity was enhanced effectively, while upon addition of TM into the o‐phen–Zn²⁺ complex solution, the intensity of the system was gently quenched, which was termed the ‘turn‐on–off’ probe. Notably, the method possessed highly selective, sensitive determination for TM with a detection limit of 0.25 μmol L^?1 and the reduced fluorescence intensity was proportional to the concentration of TM in the range 0.84–80.0 μmol L^?1. Besides, the proposed mechanism was also investigated through exploring the Fourier transform infrared (FT‐IR), nuclear magnetic resonance (NMR) spectroscopy. Furthermore, this manner was successfully applied into practical samples for TM detection with satisfactory results.     

Sensitive determination of enoxacin in pharmaceutical formulations by its quench effect on the fluorescence of glutathione‐capped CdTe quantum dots

A sensitive and simple method for the determination of enoxacin (ENX) was developed based on the fluorescence quenching effect of ENX for glutathione (GSH)‐capped CdTe quantum dots (QDs). Under optimum conditions, a good linear relationship was obtained from 4.333 × 10^?9 mol?L^?1 to 1.4 × 10^?5 mol?L^?1 with a correlation coefficient (R) of 0.9987, and the detection limit (3σ/K) was 1.313 × 10^?9 mol?L^?1. The corresponding mechanism has been proposed on the basis of electron transfer supported by ultraviolet–visible (UV) light absorption, fluorescence spectroscopy, and the measurement of fluorescence lifetime. The method has been applied to the determination of ENX in pharmaceutical formulations (enoxacin gluconate injections and commercial tablets) with satisfactory results. The proposed method manifested several advantages such as high sensitivity, short analysis time, low cost and ease of operation. Copyright © 2015 John Wiley & Sons, Ltd.     

Impact of light quality on a native Louisiana Chlorella vulgaris/Leptolyngbya sp. co‐culture

Light effect on cultures of microalgae has been studied mainly on single species cultures. Cyanobacteria have photosynthetic pigments that can capture photons of wavelengths not available to chlorophylls. A native Louisiana microalgae (Chlorella vulgaris ) and cyanobacteria (Leptolyngbya sp.) co‐culture was used to study the effects of light quality (blue–467 nm, green–522 nm, red–640 nm and white–narrow peak at 450 nm and a broad range with a peak at 550 nm) at two irradiance levels (80 and 400 μmol m^?2 s^?1) on the growth, species composition, biomass productivity, lipid content and chlorophyll‐a production. The co‐culture shifted from a microalgae dominant culture to a cyanobacteria culture at 80 μmol m^?2 s^?1. The highest growth for the cyanobacteria was observed at 80 μmol μmol m^?2 s^?1 and for the microalgae at 400 μmol m^?2 s^?1. Red light at 400 μmol m^?2 s^?1 had the highest growth rate (0.41 d^?1), biomass (913 mg L^?1) and biomass productivity (95 mg L^?1 d^?1). Lipid content was similar between all light colors. Green light had the highest chlorophyll‐a content (1649 μg/L). These results can be used to control the species composition of mixed cultures while maintaining their productivity.     

Effects of Cadmium Stress on Leaf Chlorophyll Fluorescence and Photosynthesis of Elsholtzia argyi—A Cadmium Accumulating Plant

A hydroponic experiment was conducted to investigate the effects of cadmium (Cd) on chlorophyll fluorescence and photosynthetic parameters on a Cd accumulating plant of Elsholtzia argyi. Four weeks-seedlings of E. argyi were treated with 0 (CK) 5, 10, 15, 20, 25, 30, 40, 50 and 100 μmol L^?1 Cd for 21days. Fv/Fo, Fv/Fm, qP, ΦPSП, ETR and Fv′/Fm′ were significantly increased under low Cd (5–15 μmol L^?1 for Fv/Fo, Fv/Fm and qP, 5–10 μmol L^?1 for ΦPSП, ETR and Fv′/Fm′) stress, and these parameters were similar to control under Cd ≤ 50μmol L^?1. All above parameters were significantly decreased at 100 μmol L^?1 Cd. Compared with control, Pn was significantly (P < 0.05) increased under 5–30 μmol L^?1 Cd. However, 50 and 100 μmol L^?1 Cd significantly (P < 0.05) reduced it. Gs and Tr were substantially decreased at 50–100 and 40–100 μmol L^?1 Cd, respectively. Ci was significantly increased at 50 and 100 μmol L^?1 Cd. High Cd-induced decrease of Pn is not only connected to stomatal limitation but also to the inhibition of Fv/Fo, Fv/Fm, ΦPSП, qP, ETR and increase of NPQ. Maintain chlorophyll fluorescence and photosynthesis parameters under its Cd tolerance threshold were one of tolerance mechanisms in E. argyi.     

Sensitive spectrofluorometric method for the determination of ascorbic acid in pharmaceutical nutritional supplements using acriflavine as a fluorescence reagent

An easily performed, specific, sensitive, rapid, reliable and inexpensive procedure for the spectrofluorometric quantitation of ascorbic acid was proposed using acriflavine as a fluorescence quenching reagent. The procedure was based on the determined quenching effect of ascorbic acid on the natural fluorescence signal of acriflavine and the reaction between ascorbic acid and acriflavine in Britton–Robinson buffer solution (pH 6) to produce an ion‐associated complex. The reduction in acriflavine fluorescence intensity was detected at 505 nm, while excitation occurred at 265 nm. The relationship between quenching fluorescence intensity (?F) and concentration of ascorbic acid was linear (R² = 0.9967) within the range 2–10 μg/ml and with a detection limit of 0.08 μg/ml. No significant interference was detected from other materials often found in pharmaceutical nutritional tablets. The obtained results were compared with those from high‐performance liquid chromatography and appeared in good agreement, with no important differences in precision or accuracy. The proposed spectrofluorimetric method was used to determine the amount of ascorbic acid in a number of commercial pharmaceutical nutritional supplement tablets with a 95% confidence performance.     

High‐sensitivity spectrofluorimetric determination of tiopronin based on inhibition of hemoglobin

A highly sensitive and simple spectrofluorimetric method for the determination of tiopronin based on its inhibitory effect on the hemoglobin‐catalyzed reaction of H₂O₂ and l ‐tyrosine was developed. The concentration of tiopronin is linear with decreased fluorescence (ΔF) of the system under the optimal experimental conditions. The calibration graph is linear in the range 1.23 × 10^?8 to 3.06 × 10^?5 mol L^?1 with a detection limit of 6.13 × 10^?9 mol L^?1. The relative standard deviation was 4.38% for 11 determinations of 6.13 × 10^?6 mol L^?1. This method can be used for the determination of tiopronin in pharmaceuticals with satisfactory results. Copyright © 2010 John Wiley & Sons, Ltd.     

Silicon nanoparticles synthesized using a microwave method and used as a label‐free fluorescent probe for detection of VB12

A simple and rapid detection strategy for vitamin B₁₂ (VB₁₂) was established based on label‐free silicon quantum dots (SiQDs); the detection mechanism was additionally investigated. SiQDs were synthesized using a one‐step microwave method, and their fluorescence was stronger than that synthesized using the hydrothermal method. SiQDs fluorescence was quenched using VB₁₂ due to the inner filter effect (IFE), which was demonstrated using ultraviolet (UV) absorption spectra, fluorescence lifetime, transmission electron microscopy and zeta potential analysis. Subsequently, quercetin (Que) and doxorubicin (Dox) with absorption peaks that overlapped the excitation or emission peaks of SiQDs respectively were used as control groups to investigate the quenching mechanism. Results showed that quenching efficiency was related to the level of overlap between the adsorption peak of the quencher and the excitation or emission peaks of SiQDs. A greater level of overlap caused a higher quenching efficiency. Therefore, the sensitive quenching of VB₁₂ for SiQDs was due to the synergistic effect of the synchronous overlap between the absorption peak of VB₁₂ with the excitation and emission peaks of SiQDs. Fluorescence quenching efficiency increased linearly in the 0.5 to 16.0 μmol·L^?1 VB₁₂ concentration range, and the detection limit was 158 nmol·L^?1. In addition, SiQDs were applied to determine VB₁₂ in tablets and human urine samples with satisfactory recoveries ranging from 97.7 to 101.1%.     

Fluorescence quenching and bonding properties of some hydroxamic acid derivatives by iron(III) and manganese(II)

Spectrophotometric investigations of highly fluorescent metal chelating molecules are of relevance due to their potential application in novel, selective fluorescence‐based sensors. Benzene and naphthalene chromophores are highly fluorescent while hydroxamic acids are widely used as ligands for complexation of transition metals. In order to develop fluorescence probes, several phenyl derivatives of N‐phenylbenzohydroxamic acid and an aminodihydroxamic acid linked with a naphthalene chromophore were synthesized and their selective ionophoric properties towards iron(III) and manganese(II) ions were investigated using fluorescence and absorption spectroscopy. Both methods confirm the formation of 1:1 and 1:2 complexes for iron(III) and a 1:1 complex for manganese(II). The complex that is formed depends on the concentration of the ligand and pH of the medium. The amino dihydroxamic acid exhibits a prominent selectivity towards iron(III) with a two‐step 1:1 and 1:2 quenching mechanism at pH 3 and towards manganese(II) with a 1:1 quenching mechanism at a probe concentration of 1 × 10^?5 mol dm^?3 at pH 9.5 The logarithm of overall formation constants of 1:1 and 1:2 complexes of iron(III) were estimated as 3.30 and 9.05, respectively. Copyright © 2008 John Wiley & Sons, Ltd.     

Fluorescence sensing of nitric oxide in aqueous solution by triethanolamine‐modified CdSe quantum dots

The water‐soluble luminescent CdSe quantum dots were prepared by ligand exchange with triethanolamine (TEA). Oxygen can reversibly enhance the fluorescence of the synthesized quantum dots (TEA‐CdSe‐QDs) in aqueous solution. Nitric oxide radical (NO) can react easily with dissolved oxygen in water and was found to have a significant quenching effect on the fluorescence of the TEA‐CdSe‐QDs. The fluorescence responses were concentration‐dependent and can be well described by the typical Stern–Volmer equation. A good linear relationship (R² = 0.9963) was observed over the range 5.92 × 10^?7 to 1.85 × 10^?5 mol/L nitric oxide. Above this concentration was a second linear region ranging from 2.12 × 10^?5 to 1.12 × 10^?4 mol/L NO with a gentler slope. The detection limit, calculated following the 3σ IUPAC criteria, was 3.02 × 10^?7 mol/L. The interference effect of some common interferents such as nitrite (NO₂^?), nitrate (NO₃^?), glucose and l ‐ascorbic acid on the detection of NO was negligible for the proposed system, demonstrating the potential utility of this probe for the detection of NO in biological systems. The possible mechanism was also discussed. Copyright © 2009 John Wiley & Sons, Ltd.     

The influence of light on copper‐limited growth of an oceanic diatom,Thalassiosira oceanica (Coscinodiscophyceae)

Thalassiosira oceanica (CCMP 1005) was grown over a range of copper concentrations at saturating and subsaturating irradiance to test the hypothesis that Cu and light were interacting essential resources. Growth was a hyperbolic function of irradiance in Cu‐replete medium (263 fmol Cu′ · L^?1) with maximum rates achieved at 200 μmol photons · m^?2 · s^?1. Lowering the Cu concentration at this irradiance to 30.8 fmol Cu′ · L^?1 decreased cellular Cu quota by 7‐fold and reduced growth rate by 50%. Copper‐deficient cells had significantly slower (P < 0.0001) rates of maximum, relative photosynthetic electron transport (rETR_max) than Cu‐sufficient cells, consistent with the role of Cu in photosynthesis in this diatom. In low‐Cu medium (30.8 fmol Cu′ · L^?1), growth rate was best described as a positive, linear function of irradiance and reached the maximum value measured in Cu‐replete cells when irradiance increased to 400 μmol photons · m^?2 · s^?1. Thus, at high light, low‐Cu concentration was no longer limiting to growth: Cu concentration and light interacted strongly to affect growth rate of T. oceanica (P < 0.0001). Relative ETR_max and Cu quota of cells grown at low Cu also increased at 400 μmol photons · m^?2 · s^?1 to levels measured in Cu‐replete cells. Steady‐state uptake rates of Cu‐deficient and sufficient cells were light‐dependent, suggesting that faster growth of T. oceanica under high light and low Cu was a result of light‐stimulated Cu uptake.     

New luminol chemiluminescence reaction using diperiodatoargentate as oxidate for the determination of amikacin sulfate

A new chemiluminescence (CL) reaction between luminol and diperiodatoargentate {K₂ [Ag (H₂IO₆) (OH) ₂]} was observed in alkaline medium. The CL intensity could be greatly enhanced by amikacin sulfate. Therefore a new CL method for the determination of amikacin sulfate was built by combining with flow injection technology. A possible mechanism of the CL reaction was proposed via the investigation of the CL kinetic characteristics, the CL spectrum and the UV absorption spectra of some related substance. The concentration range of linear response was 5.1 × 10^?8 to 5.1 × 10^?6 mol L^?1 with a detection limit of 1.9 × 10^?8 mol L^?1 (3σ). The proposed method had good reproducibility with a relative standard deviation of 2.8% (n = 7) for 5.1 × 10^?7 mol L^?1 of amikacin sulfate. It was successfully applied to determine amikacin sulfate in serum. Copyright © 2009 John Wiley & Sons, Ltd.