Plasmonic Enhancement During Femtosecond Laser Drilling of Sub-wavelength Holes in Metals

Precise ablation of metals using tightly focused femtosecond laser pulses with intensities close to the damage threshold can yield sub-wavelength, nanometer-sized holes or craters. These structures in metals can exhibit plasmonic effects, thereby affecting the interactions involved. We numerically simulate light propagation inside such holes and model the ablation process. We show that surface plasmon resonances can be excited at near-infrared and visible wavelengths. At resonance wavelengths, significant enhancement of aspect ratio is possible. Our results show that plasmonic effects are essential for the understanding of precision laser processing of metals, and they can be exploited to significantly enhance the performance of laser micro- and nano-machining.     

Metal-Dielectric-Graphene Hybrid Heterostructures with Enhanced Surface Plasmon Resonance Sensitivity Based on Amplitude and Phase Measurements

Metal-dielectric-graphene hybrid heterostructures based on oxides Al₂O₃, HfO₂, and ZrO₂ as well as on complementary metal–oxide–semiconductor compatible dielectric Si₃N₄ covering plasmonic metals Cu and Ag have been fabricated and studied. We show that the characteristics of these heterostructures are important for surface plasmon resonance biosensing (such as minimum reflectivity, sharp phase changes, resonance full width at half minimum and resonance sensitivity to refractive index unit (RIU) changes) can be significantly improved by adding dielectric/graphene layers. We demonstrate maximum plasmon resonance spectral sensitivity of more than 30,000 nm/RIU for Cu/Al₂O₃ (ZrO₂, Si₃N₄), Ag/Si₃N₄ bilayers and Cu/dielectric/graphene three-layers for near-infrared wavelengths. The sensitivities of the fabricated heterostructures were?~?5–8 times higher than those of bare Cu or Ag thin films. We also found that the width of the plasmon resonance reflectivity curves can be reduced by adding dielectric/graphene layers. An unexpected blueshift of the plasmon resonance spectral position was observed after covering noble metals with high-index dielectric/graphene heterostructures. We suggest that the observed blueshift and a large enhancement of surface plasmon resonance sensitivity in metal-dielectric-graphene hybrid heterostructures are produced by stationary surface dipoles which generate a strong electric field concentrated at the very thin top dielectric/graphene layer.

     

Tailoring Plasmon Lifetime in Suspended Nanoantenna Arrays for High-Performance Plasmon Sensing

We demonstrate significantly longer plasmon lifetime and stronger electric field enhancement by lifting the nanoantenna arrays above the substrate by dielectric nanopillars. The role of the pillar is to offer a more homogeneous dielectric background allowing stronger diffraction coupling among plasmonic nanoantennas leading to a Fanolike asymmetric lineshape. It is found that the electric fields around the nanoantennas can be greatly enhanced when the Fanolike resonance is excited, and a 4.2 times enhancement is achieved compared with the pure resonance in individual nanoantennas. Furthermore, only a collective surface mode with its electric fields of the same direction as the induced electric moment in the nanoantennas could mediate the excitation of such a Fanolike resonance. More importantly, the sensitivity and the figure of merit (FOM) of this plasmonic structure can reach as high as 900 nm/RIU and 53, respectively. Our study offers a new, simple, and efficient way to design the plasmonic systems with desired electric field enhancement and spectral lineshape for different applications.     

Circulating microRNA breast cancer biomarker detection in patient sera with surface plasmon resonance imaging biosensor

In this article, we report for the first time, the detection of circulating miRNA as a breast cancer biomarker in patient sera using surface plasmon resonance imaging biosensor. The advantage of this approach lies in the rapid, label-free and sensitive detection. The sensor excites plasmonic resonance on the gold sensor surface and specific DNA-miRNA molecular bindings elucidate responses in the plasmonic resonance image. Experiments of detecting synthetic miRNA molecules (miR-1249) were performed and the sensor resolution was found to be 63.5 nM. The sensor was further applied to screen 17 patient serum samples from National Cancer Centre Singapore and Tan Tock Seng Hospital. Sensor intensity response was found to differ by 20% between malignant and benign cases and thus forms, a potential and an important metric in distinguishing benignity and malignancy.     

Portable Capillary Sensor Integrated with Plasmonic Platform for Monitoring Water Pollutants

In this work, a label-free and inexpensive method for the monitoring of water pollutants is demonstrated. We introduce a localized surface plasmon resonance (LSPR) based plasmonic capillary optical biosensor to detect microalgae cells. Here, the plasmonic capillary biosensor was prepared by decorating the inner walls of a glass capillary with gold nanoparticles that were employed for investigations. Since the gold nanoparticle has the potential to sense pollutants in water rapidly with high sensitivity and they are expected to perform a significant role in environmental monitoring. Our proposed plasmonic capillary sensor has a detection limit of 25 algal cells (Chlorella sp. CB4). Furthermore, the plasmonic capillary sensing platform significantly simplifies sensor fabrication and reduces the cost of the device. We believe that the presented plasmonic sensor could stand as a potential candidate for developing a cost-effective, label-free, and rapid sensing platform to detect microalgae pollutants present in the water at very low concentrations.

     

Waveguide-Coupled Surface Plasmon Resonance Sensor for Both Liquid and Gas Detections

Plasmonics - In this paper, we propose a novel surface plasmon resonance sensor for both liquid and gas detections, which is based on the two dielectric planar waveguide (PWG)-coupled plasmonic...     

Platinum Layers Sandwiched Between Black Phosphorous and Graphene for Enhanced SPR Sensor Performance

Highly sensitive surface plasmon resonance (SPR) sensor consisting of Ag-Pt bimetallic films sandwiched with 2D materials black phosphorus (BP) and graphene over Pt layer in Kretschmann configuration is analyzed theoretically using the transfer matrix method. Numerical results show that upon suitable optimization of thickness of Ag-Pt layers and the number of layers of BP and graphene, sensitivity as high as 412°/RIU (degree/refractive index unit) can be achieved for p-polarized light of wavelength 633 nm. This performance can be tuned and controlled by changing the number of layers of BP and graphene. Furthermore, the addition of graphene and heterostructures of black phosphorus not only improved the sensitivity of the sensor but also kept the FWHM of the resonance curve much smaller than the conventional sensor utilizing Au as plasmonic metal and hence improved the resolution to a significant extent. We expect that this new proposed design will be useful for medical diagnosis, biomolecular detection, and chemical examination.

     

Impact of Nonuniform Electron Density on Plasmonic Properties of Metal Nanoparticles

The interfacial nonuniformity of the electron density that occurs in metals as a result of atomic imperfections can strongly affect the plasmonic properties of metallic nanostructures. Under certain conditions, it induces the bulk plasmon resonance in the transition area and can significantly change scattering and absorption of light by metallic nanostructures in a broad frequency range. This effect is numerically demonstrated for radially nonuniform spherical silver nanoparticles and analytically investigated with respect to the resonant coupling with the dipolar surface plasmons of the metal core.     

U-Shaped Photonic Crystal Fiber Based Surface Plasmon Resonance Sensors

A surface plasmon resonance sensor based on a U-shaped photonic crystal fiber with a rectangular lattice has been designed through finite element method. The U-shaped fiber exhibits not only stronger mechanical strength but also better sensor performance than our previous scheme. The upper detection limit extends to higher analyze refractive index, 1.384, for phase interrogation. We introduce a ratio to evaluate the impact of higher order plasmonic mode. For wavelength modulation scheme, the parameter to describe the performance of a sensor is chosen to be the figure of merit, which can be up to 533.8[RIU^?1] around complete coupling condition.     

Self-Referencing Plasmonic Array Sensors

A self-referencing plasmonic platform is proposed and analyzed. By introducing a thin gold layer below a periodic two-dimensional nano-grating, the structure supports multiple modes including localized surface plasmon resonance (LSPR), surface plasmon resonance (SPR), and Fabry-Perot resonances. These modes get coupled to each other creating multiple Fano resonances. A coupled mode between the LSPR and SPR responses is spatially separated from the sensor surface and is not sensitive to refractive index changes in the surrounding materials or surface attachments. This mode can be used for self-referencing the measurements. In contrast, the LSPR dominant mode shifts in wavelength when the refractive index of the surrounding medium is changed. The proposed structure is easy to fabricate using conventional lithography and electron beam deposition methods. A bulk sensitivity of 429 nm/RIU is achieved. The sensor also has the ability to detect nanometer thick surface attachments on the top of the grating.

     

Role of Stopband and Localized Surface Plasmon Resonance in Raman Scattering from Metallo-Dielectric Photonic Crystals

Self-assembled photonic crystals grown from different colloidal sizes are coated with gold nanoparticles preferentially on their surface. The effect of localized surface plasmon resonance and the photonic stopband on the Raman scattering from these crystals is analyzed from the angle-dependent scattering measurements. The coupling of photonic and plasmonic modes at the surface of the photonic crystal is verified by measuring the increment in Raman scattering from the crystals containing the gold nanoparticles, and this increment is found to follow the spectral trend of localized surface plasmon resonance.     

Spoof Localized Surface Plasmons Excited by Plasmonic Waveguide Chip with Corrugated Disk Resonator

We designed and fabricated a millimeter plasmonic chip consisted of coplanar waveguide (CPW) and plasmonic waveguide with one corrugated disk resonator (CDR). The spoof localized surface plasmon (LSP) resonance modes can be excited by the interaction between plasmonic waveguide and CDR. Fundamental and higher order sharp spoof LSP resonances (from dipole to dodecapole) were observed in the transmission coefficient spectrum. The Q-value as high as 268.3 (octupole) was experimentally obtained. Experimental results show good agreement with theoretical and simulated ones. All the results may have potential applications in microchip based sensing and filtering.     

Remote Excited Raman Optical Activity of Adenine Along Ag Plasmonic Waveguide

We report the remote excited Raman optical activity (ROA) of adenine along Ag plasmonic waveguide. First, the surface plasmons that propagate along Ag nanowire is demonstrated experimentally. Second, the Raman spectra of adenine are measured experimentally. Third, the remote exited ROA by plasmonic waveguide are measured and compared. It is found that the plasmon chirality strongly influenced the molecular ORA by the local surface plasmon and remote plasmon waveguide. The plasmon chirality of nanostructures and the chirality plasmon waveguide should be considered in the experiments for the local and remote measurement.     

Controllable Mode Hybridization and Interaction Within a Plasmonic Cavity Formed by Two Bimetallic Gratings

We theoretically study mode hybridization and interaction among surface plasmon polariton Bloch wave mode, Fabry–Perot cavity mode, and waveguide mode within a plasmonic cavity composed by two parallel planar bimetallic gratings. Four hybridized modes result from mode hybridization between surface plasmon polariton Bloch wave modes on the two gratings are observed. By changing the dielectric environment, mode hybridization behavior can be manipulated. Importantly, waveguide-plasmon polariton mode due to hybridization between grating supported surface plasmon polariton Bloch wave mode and cavity supported waveguide mode is observed. We demonstrate that surface plasmon polariton Bloch wave mode and Fabry–Perot cavity mode with the same mode symmetry can interact by presenting an anticrossing behavior, which can be controlled by laterally shifting one grating with respect to the other that causes a phase difference shift of the two involving modes. The proposed plasmonic cavity offers potentials for subwavelength lithography, tunable plasmonic filter, and controllable light-matter interaction.     

Plasmonically Tunable Blue-Shifted Emission from Coumarin 153 in Ag Nanostructure Random Media: A Demonstration of Fast Dynamic Surface-Enhanced Fluorescence

Enhancement of intensity and wavelength tunability of emission are desirable features for light-emitting device applications. We report on the large and tunable blue shift (60 nm) in emission from an environment-sensitive fluorophore (Coumarin153) embedded in Ag plasmonic random media. Coumarin 153 having emission at 555 nm, show a systematic blue shift (to 542, 503 and 495 nm) upon infiltration into random media fabricated by Ag nanowires of different aspect ratio (hence, surface plasmon resonances at 426, 445 and 464 nm). The blue shift is due to the fast dynamic surface-enhanced fluorescence mechanism and can be tuned by controlling the surface plasmon resonance and hotspot density in random media. Enhanced emission at desired wavelength is achieved by using nanostructures having higher extinction coefficient but same-surface plasmon resonance. Ag nanostructures of different aspect ratio used for fabricating the random media are synthesized by chemical route.     

Optimization of immunolabeled plasmonic nanoparticles for cell surface receptor analysis

Noble metal nanoparticles hold great potential as optical contrast agents due to a unique feature, known as the plasmon resonance, which produces enhanced scattering and absorption at specific frequencies. The plasmon resonance also provides a spectral tunability that is not often found in organic fluorophores or other labeling methods. The ability to functionalize these nanoparticles with antibodies has led to their development as contrast agents for molecular optical imaging. In this review article, we present methods for optimizing the spectral agility of these labels. We discuss synthesis of gold nanorods, a plasmonic nanoparticle in which the plasmonic resonance can be tuned during synthesis to provide imaging within the spectral window commonly utilized in biomedical applications. We describe recent advances in our group to functionalize gold and silver nanoparticles using distinct antibodies, including EGFR, HER-2 and IGF-1, selected for their relevance to tumor imaging. Finally, we present characterization of these nanoparticle labels to verify their spectral properties and molecular specificity.     

Dual Polarization Measurements in the Hybrid Plasmonic Biosensors

A novel affinity biosensor is proposed based on the hybrid plasmonic platform. The proposed biosensor benefits from the high sensitivity of the surface plasmon resonance (SPR), while at the same time, it is capable of performing measurements in both the TM and TE polarizations (p- and s-polarizations). Unlike the conventional SPR biosensors, the polarization diversity of the hybrid sensor allows for decoupling of the bulk index variations in the fluidic channels (due to variations in concentration, decomposition, temperature, and so on) from the surface properties of the attached molecules. Compatibility of the proposed hybrid plasmonic biosensor with standard Si-processing techniques and the simplicity of its design are other advantages of the sensor which makes its fabrication straightforward. The best figure of merit for the biosensor is defined based on the minimum detection limit and a genetic algorithm is used to optimize the device. A method of de-convolving the surface and bulk effects is also discussed.     

Optimization of Optoelectronic Plasmonic Structures

We discuss the interplay between surface plasmon polaritons (SPPs) and localized shape resonances (LSRs) in a plasmonic structure working as a photo-coupler for a GaAs quantum well photodetector. For a targeted electronic inter-subband transition inside the quantum well, maximum photon absorption is found by compromising two effects: the mode overlapping with incident light and the lifetime of the resonant photons. Under the optimal conditions, the LSR mediates the coupling between the incident light and plasmonic structure while the SPP provides long-lived resonance which is limited ultimately by metal loss. The present work provides insight to the design of plasmonic photo-couplers in semiconductor optoelectronic applications.     

Plasmonic Focusing in Nanostructures

In this review, we show that by designing the metallic nanostructures, the surface plasmon (SP) focusing has been achieved, with the focusing spot at a subwavelength scale. The central idea is based on the principle of optical interference that the constructive superposition of SPs with phase matching can result in a considerable electric-field enhancement of SPs in the near field, exhibiting a pronounced focusing spot. We first reviewed several new designs for surface plasmon focusing by controlling the metallic geometry or incident light polarization: We made an in-plane plasmonic Fresnel zone plates, a counterpart in optics, which produces an obvious SP focusing effect; We also fabricated the symmetry broken nanocorrals which can provide the spatial phase difference for SPs, and then we propose another plasmon focusing approach by using semicircular nanoslits, which gives rise to the phase difference through changing refractive index of the medium in the nanoslits. Further, we showed that the spiral metallic nanostructure can be severed as plasmonic lens to control the plasmon focusing under a linearly polarized light with different angles.

     

Highly Sensitive Plasmonic Sensor Based on Fano Resonance from Silver Nanoparticle Heterodimer Array on a Thin Silver Film

We investigate the optical spectrum of a multilayer metallic slab using multiple-scattering formalism. A thin silver film is attached to a periodic array of heterodimers consisting of two vertically spaced silver nanoparticles of different radii. Depending on the radius of nanoparticles, heterodimer array presents a simple nanoscale geometry which gives rise to remarkable plasmonic properties of multipolar resonances. Due to the coherent interference of the localized nanoparticle plasmons (discrete mode) and surface plasmon polaritons of metallic film (continuous mode), the reflection spectrum represents a sharp asymmetric Fano resonance dip, which is strongly sensitive to the refractive index of the surrounding embedded dielectric host. The physical features contribute to a highly efficient plasmonic sensor for refractive index sensing with sensitivity of ～1.5?×?10^?3 RIU/nm.