A Polyaniline‐Coated Sulfur/Carbon Composite with an Enhanced High‐Rate Capability as a Cathode Material for Lithium/Sulfur Batteries

Polyaniline‐coated sulfur/conductive‐carbon‐black (PANI@S/C) composites with different contents of sulfur are prepared via two facile processes including ball‐milling and thermal treatment of the conductive carbon black and sublimed sulfur, followed by an in situ chemical oxidative polymerization of the aniline monomer in the presence of the S/C composite and ammonium persulfate. The microstructure and electrochemical performance of the as‐prepared composites are investigated systematically. It is demonstrated that the polyaniline, with a thickness of ≈5–10 nm, is coated uniformly onto the surface of the S/C composite forming a core/shell structure. The PANI@S/C composite with 43.7 wt% sulfur presents the optimum electrochemical performance, including a large reversible capacity, a good coulombic efficiency, and a high active‐sulfur utilization. The formation of the unique core/shell structure in the PANI@S/C composites is responsible for the improvement of the electrochemical performance. In particular, the high‐rate charge/discharge capability of the PANI@S/C composites is excellent due to a synergistic effect on the high electrical conductivity from both the conductive carbon black in the matrix and the PANI on the surface. Even at an ultrahigh rate (10C), a maximum discharge capacity of 635.5 mA h per g of sulfur is still retained for the PANI@S/C composite after activation, and the discharge capacity retention is over 60% after 200 cycles.     

Preparation and characterization of polyaniline/chitosan blend film

Films consisting of a blend of a chitosan hydrogel and a conductive polymer, polyaniline (PANI), were prepared and characterized for their electrical and mechanical properties. Polyaniline in emeraldine base (EB) form was dispersed in chitosan solution and blend films were obtained by solution casting. The PANI particles in the blend films were then doped with HCl where we observed reductions in the film tensile strength and Young's modulus by about 30%, but the films electrical conductivity increased by 6 orders of magnitude. The highest electrical conductivity of the blend films was of the order 10⁻⁴ S/cm. The electrical and mechanical properties of the films varied with polyaniline content, acid dopant type, acid dopant concentration, and doping time.     

Polyaniline grafted polyacylonitrile conductive composite fibers for reversible immobilization of enzymes: Stability and catalytic properties of invertase

Polyacylonitrile fibers (PAN) surfaces were modified with chemical polymerization of conductive polyaniline (PANI) in the presence of potassium dichromate as an oxidizing agent. The effect of aniline concentration on the grafting efficiency and on the electrical surface resistance of PAN/PANI composite fibers was investigated. The surface resistance of the conductive composite fibers in this work was found to be between 8.0 and 0.5 kΩ/cm. As the amount of grafted PANI increased on the PAN fibers the electrical resistance of composite fibers decreased. The PAN/PANI composite fibers were characterized by SEM and FTIR studies. Composite PAN/PANI fibers were used for reversible immobilization of invertase. The immobilization efficiency and the activity of the immobilized invertase (from 1.0 mg/mL invertase solution at pH 5.5) were increased with increasing PANI contents of the composite fibers. The maximum amount of immobilized enzyme onto composite fibers containing 2.0% PANI was about 76.6 mg/g. The optimum pH for the free enzyme was observed at 5.0. On the other hand, immobilized invertase yielded a broad optimum pH profile between pH 5.0 and 7.0. Immobilized invertase exhibited 83% of its original activity even after two months storage at 4 °C while the free enzyme showed only 7% of its initial activity.     

Synthesis of conducting polyelectrolyte complexes of polyaniline and poly(2-acrylamido-3-methyl-1-propanesulfonic acid) catalyzed by pH-stable palm tree peroxidase

Comparison of the stability of five plant peroxidases (horseradish, royal palm tree leaf, soybean, and cationic and anionic peanut peroxidases) was carried out under acidic conditions favorable for synthesis of polyelectrolyte complexes of polyaniline (PANI). It demonstrates that palm tree peroxidase has the highest stability. Using this peroxidase as a catalyst, the enzymatic synthesis of polyelectrolyte complexes of PANI and poly(2-acrylamido-3-methyl-1-propanesulfonic acid) (PAMPS) was developed. The template polymerization of aniline was carried out in aqueous buffer at pH 2.8. Varying the concentrations of aniline, PAMPS, and hydrogen peroxide as reagents, favorable conditions for production of PANI were determined. UV-vis-NIR absorption and EPR demonstrated that PAMPS and PANI formed the electroactive complex similar to PANI doped traditionally using low molecular weight sulfonic acids. The effect of pH on conformational variability of the complex was evaluated by UV-vis spectroscopy. Atomic force microscopy showed that a size of the particles of the PANI-PAMPS complexes varied between 10 and 25 nm, depending on a concentration of PAMPS in the complex. The dc conductivity of the complexes depends also on the content of PAMPS, the higher conductivity being for the complexes containing the lower content of the polymeric template.     

Synthesis of electroconductive polyaniline using immobilized laccase

A new method for synthesis of the conductive complex between polyaniline (PANI) and poly(2-acrylamido-2-methyl-1-propanosulfonic acid) (PAMPS) was proposed; in this method, the immobilized laccase from the basidiomycete Trametes hirsuta is used as a biocatalyst for aniline oxidative polymerization. The conditions for laccase immobilization on CM cellulose by bifunctional Woodward’s reagent were optimized. The catalytic properties of immobilized and native laccases were compared. The immobilized laccase appeared an efficient catalyst for the oxidative radical polymerization of aniline on polysulfonic acid matrix at 4°C. It was demonstrated that the immobilized enzyme could be repeatedly used for enzymatic synthesis of this polymer. Several spectral characteristics of the PANI/PAMPS complexes synthesized at various pH values were studied. The conductance of PANI specimens produced using immobilized laccase as a catalyst was 13 mS/cm.     

Polyaniline/polyacrylamide conducting composite hydrogel with a porous structure

A polyaniline/polyacrylamide composite hydrogel is synthesized, characterized and measured. Fourier transform infrared spectroscopy reveals that partial polyaniline chains have grafted on the nitrogen atoms of polyacrylamide. X-ray diffraction shows that typical polyaniline crystallization is formed in polyaniline/polyacrylamide composite, which is advantageous to increase the electrical conductivity of the composite hydrogel. UV–Vis spectra indicates the formation of high conductive emeraldine polyaniline salt in polyaniline/polyacrylamide composite. Scanning electron microscopy shows a typical porous structure in the composite hydrogel. The polyaniline/polyacrylamide hydrogel has a good conductivity of 0.6 S/cm and good release stability in acidic and neutral conditions.     

Assembly of dandelion-like Au/PANI nanocomposites and their application as SERS nanosensors

The monodisperse, uniform dandelion-like Au/polyaniline (PANI) composite nanospheres were synthesized by a simple one-step process without any additives or templates. The nanospheres are really composed of many short nanorods and the average diameter of whole nanospheres is about 180 nm. The morphology of Au/PANI composites could be controlled by adjusting the molar ratio of HAuCl(4) to aniline. The prepared nanocomposite is developed as a wonderful sensor for the detection of Hg(2+) ions, which is based upon the Raman intensity response of PANI to Hg(2+) ions. Results from the morphology-dependent sensitivity investigations show that the dandelion-like nanospheres have an ultra sensitive response (as low as 10(-11)M) compared with other morphologies. The nanosensor also exhibits good reproducibility and greater selectivity for Hg(2+) ions than the other heavy metal ions. And the mechanism was proposed. The proposed nanosensors can be applied for highly sensitive and selective chemical analysis in a variety of environmental detection.     

Reversible immobilization of uricase on conductive polyaniline brushes grafted on polyacrylonitrile film

Polyacrylonitrile film (PAN) surfaces were modified with chemical polymerization of conductive polyaniline (PANI) in the presence of potassium dichromate as an oxidizing agent. The conductive films were used for immobilization of uricase. The surface resistance of the conductive film in this work was found to be 0.97 kΩ/cm. The maximum amount of immobilized enzyme on conductive film containing 2.4% PANI was about 216 μg/cm². The optimum pH for free and immobilized enzymes was observed at 7.0 and 7.5, respectively. The K _m values for free and immobilized uricase were found to be 94 and 138 μM, respectively. V _max values were calculated as 1.87 and 1.63 U/mg protein for the free and immobilized enzymes, respectively. Immobilized uricase exhibited ~68% of its original activity even after 2 months of storage at 4 °C while the free enzyme lost its initial activity within 4 weeks.     

Characterizations of glycerol plasticized-starch (GPS)/carbon black (CB) membranes prepared by melt extrusion and microwave radiation

As electrically conductive polymer composites, glycerol plasticized-starch (GPS)/carbon black (CB) membranes are respectively prepared by melt extrusion and microwave radiation. Scanning electron microscopy shows that the electrical conductance network of CB is formed in GPS/CB membranes, prepared by microwave radiation (GPS/CB-MR). However, the agglomerates of CB particles are isolated in GPS/CB membranes, prepared by melt extrusion (GPS/CB-ME). Fourier Transform Infrared (FTIR) spectroscopy reveals that CB and GPS matrix can form the interaction in GPS/CB membranes. According to Nicholais–Narkis models, the reinforcing effect of CB is more obvious in GPS/CB-MR membranes than in GPS/CB-ME membranes. GPS/CB-MR membranes exhibit a low electrical percolation threshold of 2.398 vol% CB loading and the conductivity of the membrane containing 4.236 vol% CB reaches 7.08 S/cm, while GPS/CB-ME membranes shows a very low conductivity of 10⁻⁸ S/cm at the high CB content. In addition, GPS/CB-MR membranes have better water vapor barrier than GPS/CB-ME membranes.     

Effect of conductive polymers coated anode on the performance of microbial fuel cells (MFCs) and its biodiversity analysis

Conductive polymer, one of the most attractive electrode materials, has been applied to coat anode of MFC to improve its performance recently. In this paper, two conductive polymer materials, polyaniline (PANI) and poly(aniline-co-o-aminophenol) (PAOA) were used to modify carbon felt anode and physical and chemical properties of the modified anodes were studied. The power output and biodiversity of modified anodes, along with unmodified carbon anode were compared in two-chamber MFCs. Results showed that the maximum power density of PANI and PAOA MFC could reach 27.4 mW/m(2) and 23.8 mW/m(2), comparing with unmodified MFC, increased by 35% and 18% separately. Low temperature caused greatly decrease of the maximum voltage by 70% and reduced the sorts of bacteria on anodes in the three MFCs. Anode biofilm analysis showed different bacteria enrichment: a larger mount of bacteria and higher biodiversity were found on the two modified anodes than on the unmodified one. For PANI anode, the two predominant bacteria were phylogenetically closely related to Hippea maritima and an uncultured clone MEC_Bicarb_Ac-008; for PAOA, Clostridiales showed more enrichment. Compare PAOA with PANI, the former introduced phenolic hydroxyl group by copolymerization o-aminophenol with aniline, which led to a different microbial community and the mechanism of group effect was proposed.     

Efficiency of enzymatic and non-enzymatic catalysts in the synthesis of insoluble polyphenol and conductive polyaniline in water

The present work analyzes the potential use of white-rot fungi (WRF) and hematin for phenol and aniline polymerization, as a low-cost alternative to horseradish peroxidase (HRPC). The objective is to evaluate the capability of these catalysts to produce tailor-made aniline as well as to eliminate phenols by precipitation from aqueous solution. 4-Aminoantypirine (4AAP) was used to test phenoxide formation by crude protein preparations of white-rot fungi at selected conditions. The crude extracts of Pleurotus sajor-caju (PSC) were selected because of the promising values obtained for the phenoxide formation rate. HRPC/H₂O₂ and P. sajor-caju derived enzymes/H₂O₂ (PSC/H₂O₂) systems produced soluble polyaniline in the presence of polystyrene sulphonated (PES), with high aniline conversions at 45 °C. For the case of insoluble polyphenol production, the PSC-derived enzymes, in absence of hydrogen peroxide, produced insoluble polyphenol with similar efficiencies as those found with HRPC or hematin in a one step phenol treatment (near 40% phenol conversion). For the aniline process, at least 75% aniline conversion was obtained when using PSC enzymes at room temperature. After long reaction times, the lignin-modifying enzymes derived from PSC only produced a conductive form of polyaniline (PANI) at lower temperatures than those required when employing HRPC. Fungal enzymes look promising for eliminating aniline/phenol from wastewaters since the obtained results demonstrated that they are able to polymerizate and precipitate them from aqueous solutions.     

Enzymatic synthesis of a conducting complex of polyaniline and poly(2-acrylamido-2-methyl-1-propanesulfonic acid) using palm tree peroxidase and its properties

An enzymatic method of producing a conducting polyelectrolyte complex of polyaniline (PANI) and poly(2-acrylamido-2-methyl-1-propanesulfonic acid) (PAMPS) was developed. Acidic stable peroxidase isolated from royal palm tree (Roystonea regia L.) leaves was used as a catalyst in the oxidative polymerization of aniline at pH 2.8. The synthesis procedure was optimized. Spectroscopic and electrochemical characteristics of nanoparticles of obtained PANI/PAMPS complexes at different pH were studied. It was shown that the acidity of the medium affects their properties.__________Translated from Prikladnaya Biokhimiya i Mikrobiologiya, Vol. 41, No. 3, 2005, pp. 283–287.Original Russian Text Copyright © 2005 by Mazhugo, Caramyshev, Shleev, Sakharov, Yaropolov.     

Green synthesis of conductive polyaniline by Trametes versicolor laccase using a DNA template

The green synthesis of highly conductive polyaniline by using two biological macromolecules, i.e laccase as biocatalyst, and DNA as template/dopant, was achieved in this work. Trametes versicolor laccase B (TvB) was found effective in oxidizing both aniline and its less toxic/mutagenic dimer N‐phenyl‐p‐phenylenediamine (DANI) to conductive polyaniline. Reaction conditions for synthesis of conductive polyanilines were set‐up, and structural and electrochemical properties of the two polymers were extensively investigated. When the less toxic aniline dimer was used as substrate, the polymerization reaction was faster and gave less‐branched polymer. DNA was proven to work as hard template for both enzymatically synthesized polymers, conferring them a semi‐ordered morphology. Moreover, DNA also acts as dopant leading to polymers with extraordinary conductive properties (～6 S/cm). It can be envisaged that polymer properties are magnified by the concomitant action of DNA as template and dopant. Herein, the developed combination of laccase and DNA represents a breakthrough in the green synthesis of conductive materials.     

Substituted polyaniline/chitosan composites: Synthesis and characterization

Substituted polyaniline/chitosan(PANIs/Ch) composites were chemically synthesized by using ammonium peroxydisulfate as oxidant and characterized by measurements of conductivity, FTIR, UV–vis, SEM and TGA techniques. FTIR spectra of the composites revealed that there is a strong interaction between substituted polyanilines and chitosan. Among the substituted polyaniline/chitosan composites synthesized, poly(N-ethylaniline)/chitosan PNEANI/Ch has the highest conductivity with a value of 1.68 × 10^?4 S/cm. The P2EANI/Ch composite exhibited higher thermal stability than the other composites. SEM images of the composites showed an agglomerated granular morphology of substituted polyaniline particles coated on the surface of chitosan.     

Biomimetic synthesis of a water soluble conducting molecular complex of polyaniline and lignosulfonate

A new biomimetic route for the synthesis of a conducting molecular complex of polyaniline (Pani) and a natural polyelectrolyte, lignosulfonate (LGS) is presented. A poly(ethylene glycol) modified hematin (PEG-hematin) was used to catalyze the polymerization of aniline in the presence of LGS to form a Pani/LGS complex. UV-vis, FTIR, conductivity and TGA studies for the LGS-polyaniline complex indicate the presence of a thermally stable and electrically conductive form of polyaniline. Also the presence of LGS in this complex, an inexpensive byproduct from pulp processing, provides a unique combination of properties such as electronic conductivity, processability and biodegradability. The use of this conductive complex for corrosion protection is also proposed.     

Rheological behaviors and miscibility of mixture solution of polyaniline and cellulose dissolved in an aqueous system

In our previous work, supramolecular films composed of hydrophilic cellulose and hydrophobic polyaniline (PANI) dissolved in NaOH/urea aqueous solution at low temperature through rearrangement of hydrogen bonds have been constructed. To further understand the miscibility and processability of the complex solution, the dynamic rheological behaviors of the PANI/cellulose complex solution were investigated, for the first time, in the present work. Transmission electron microscope (TEM) results demonstrated that the inclusion complexes consisted of PANI and cellulose, existed in the aqueous solution, showing a good miscibility. Time-temperatures superposition (tTs) results indicated that the PANI/cellulose solution exhibited a homogeneous system, and the complex solution was more stable than the cellulose solution in the temperature range from 5 to 25 °C. Winter-Chambon theory was proved to be capable of describing the gelation behavior of the PANI/cellulose complex solution. The relaxation exponent at the gel point was calculated to be 0.74, lower than the cellulose solution, indicating strong interactions between PANI and cellulose chains. Relatively larger flow activation energy of the PANI/cellulose solution suggested the formation and rupture of linkages in "junction zones" during the gelation processes. Furthermore, PANI/cellulose gels could form at elevated temperature as a result of the physical cross-linking and chain entanglement, and it was a thermoirreversible process. Moreover, the PANI/cellulose solution remained a liquid state for a long time at the temperature range from 0 to 8 °C, which is important for the industry process.     

Facile synthesis of degradable and electrically conductive polysaccharide hydrogels

Degradable and electrically conductive polysaccharide hydrogels (DECPHs) have been synthesized by functionalizing polysaccharide with conductive aniline oligomers. DECPHs based on chitosan (CS), aniline tetramer (AT), and glutaraldehyde were obtained by a facile one-pot reaction by using the amine group of CS and AT under mild conditions, which avoids the multistep reactions and tedious purification involved in the synthesis of degradable conductive hydrogels in our previous work. Interestingly, these one-pot hydrogels possess good film-forming properties, electrical conductivity, and a pH-sensitive swelling behavior. The chemical structure and morphology before and after swelling of the hydrogels were verified by FT-IR, NMR, and SEM. The conductivity of the hydrogels was tuned by adjusting the content of AT. The swelling ratio of the hydrogels was altered by the content of tetraaniline and cross-linker. The hydrogels underwent slow degradation in a buffer solution. The hydrogels obtained by this facile approach provide new possibilities in biomedical applications, for example, biodegradable conductive hydrogels, films, and scaffolds for cardiovascular tissue engineering and controlled drug delivery.     

Graphitic Petal Electrodes for All‐Solid‐State Flexible Supercapacitors

The charge storage characteristics of a composite nanoarchitecture with a highly functional 3D morphology are reported. The electrodes are formed by the electropolymerization of aniline monomers into a nanometer‐thick polyaniline (PANI) film that conformally coats graphitic petals (GPs) grown by microwave plasma chemical vapor deposition (MPCVD) on conductive carbon cloth (CC). The hybrid CC/GPs/PANI electrodes yield results near the theoretical maximum capacitance for PANI of 2000 F g^?1 (based on PANI mass) and a large area‐normalized specific capacitance of ≈2.6 F cm^?2 (equivalent to a volumetric capacitance of ≈230 F cm^?3) at a low current density of 1 A g^?1 (based on PANI mass). The specific capacitances remain above 1200 F g^?1 (based on PANI mass) for currents up to 100 A g^?1 with correspondingly high area‐normalized values. The hybrid electrodes also exhibit a high rate capability with an energy density of 110 Wh kg^?1 and a maximum power density of 265 kW kg^?1 at a current density of 100 A g^?1. Long‐term cyclic stability is good (≈7% loss of initial capacitance after 2000 cycles), with coulombic efficiencies >99%. Moreover, prototype all‐solid‐state flexible supercapacitors fabricated from these hybrid electrodes exhibit excellent energy storage performance.     

Fabrication and characterization of non-enzymatic glucose sensor based on ternary NiO/CuO/polyaniline nanocomposite

Novel nickel and copper oxide nanoparticle modified polyaniline (PANI) nanofibers (NiO/CuO/PANI) were fabricated and used as a non-enzymatic sensor for detecting glucose. PANI nanofibers were prepared through electrodeposition, whereas nickel and copper oxide nanoparticles were deposited on PANI nanofibers by electrodeposition and electrochemical oxidation in situ. The morphology and structure of NiO/CuO/PANI nanocomposites were characterized by field emission scanning electron microscopy (FE–SEM), X-ray diffraction (XRD), Raman spectroscopy, and Fourier transform infrared (FT–IR). The as-prepared NiO/CuO/PANI electrode was employed for non-enzymatic glucose detection in alkaline electrolyte and showed better electrocatalytic activity compared with the PANI, CuO/PANI, and NiO/PANI electrodes. Consequently, an amperometric electrode of glucose was achieved under 0.6 V versus Ag/AgCl with a wide linear range from 20 to 2500 μM (R² = 0.9978) and a low detection limit of 2.0 μM (signal/noise [S/N] = 3). This electrode can effectively analyze glucose concentration in human serum samples, avoiding interference, and is a promising non-enzymatic glucose sensor due to its low overpotential, high sensitivity, good selectivity and stability, fast response, and low cost.     

Polyaniline-uricase biosensor prepared with template process

Polyaniline (PANI) uricase biosensor prepared with template process is reported first in this paper. The fabrication process is as follows. Firstly, a PANI–uricase electrode is obtained using one-step process. Secondly, the electrode is hydrolyzed in 6.0 mol/dm³ hydrochloric acid solution to remove the uricase that may be affected by aniline monomer from PANI film. Finally, active uricase is immobilized into the PANI film based on the principle of the doping and undoping of the conducting polymer and a PANI–uricase biosensor is obtained. Some factors that affect response current are studied, such as temperature, pH, potential and substrate concentration. The determination of biosensors indicates that the response current of the biosensor prepared by template process decreases only by about 18% for 60 days, but that prepared by two-step process decreases by approximately 39% for 40 h. The uricase in PANI–uricase biosensor prepared by template process mainly interacts with the nitrogen linked to the quinoid ring. The biosensor is characterized with FTIR, UV-Vis and SEM for the first time.