The Effect of Sterilization Methods on the Physical Properties of Silk Sericin Scaffolds

Protein-based biomaterials respond differently to sterilization methods. Since protein is a complex structure, heat, or irradiation may result in the loss of its physical or biological properties. Recent investigations have shown that sericin, a degumming silk protein, can be successfully formed into a 3-D scaffolds after mixing with other polymers which can be applied in skin tissue engineering. The objective of this study was to investigate the effectiveness of ethanol, ethylene oxide (EtO) and gamma irradiation on the sterilization of sericin scaffolds. The influence of these sterilization methods on the physical properties such as pore size, scaffold dimensions, swelling and mechanical properties, as well as the amount of sericin released from sericin/polyvinyl alcohol/glycerin scaffolds, were also investigated. Ethanol treatment was ineffective for sericin scaffold sterilization whereas gamma irradiation was the most effective technique for scaffold sterilization. Moreover, ethanol also caused significant changes in pore size resulting from shrinkage of the scaffold. Gamma-irradiated samples exhibited the highest swelling property, but they also lost the greatest amount of weight after immersion for 24 h compared with scaffolds obtained from other sterilization methods. The results of the maximum stress test and Young’s modulus showed that gamma-irradiated and ethanol-treated scaffolds are more flexible than the EtO-treated and untreated scaffolds. The amount of sericin released, which was related to its collagen promoting effect, was highest from the gamma-irradiated scaffold. The results of this study indicate that gamma irradiation should have the greatest potential for sterilizing sericin scaffolds for skin tissue engineering.     

Application of a dense gas technique for sterilizing soft biomaterials

Sterilization of soft biomaterials such as hydrogels is challenging because existing methods such as gamma irradiation, steam sterilization, or ethylene oxide sterilization, while effective at achieving high sterility assurance levels (SAL), may compromise their physicochemical properties and biocompatibility. New methods that effectively sterilize soft biomaterials without compromising their properties are therefore required. In this report, a dense-carbon dioxide (CO(2) )-based technique was used to sterilize soft polyethylene glycol (PEG)-based hydrogels while retaining their structure and physicochemical properties. Conventional sterilization methods such as gamma irradiation and steam sterilization severely compromised the structure of the hydrogels. PEG hydrogels with high water content and low elastic shear modulus (a measure of stiffness) were deliberately inoculated with bacteria and spores and then subjected to dense CO(2) . The dense CO(2) -based methods effectively sterilized the hydrogels achieving a SAL of 10(-7) without compromising the viscoelastic properties, pH, water-content, and structure of the gels. Furthermore, dense CO(2) -treated gels were biocompatible and non-toxic when implanted subcutaneously in ferrets. The application of novel dense CO(2) -based methods to sterilize soft biomaterials has implications in developing safe sterilization methods for soft biomedical implants such as dermal fillers and viscosupplements.     

不同消毒方法对生物化PET 人工韧带的生物力学影响

目的:探讨环氧乙烷、高压蒸汽、60Co照射三种消毒方法,对生物化PET人工韧带的生物力学影响,为选取合适的消毒灭菌方法提供实验依据。方法:以表面改性的聚对苯二甲酸乙二醇酯纤维为材料,制备生物化PET人工韧带,分别给予环氧乙烷熏蒸、高压蒸汽、60Co照射消毒处理,并设未作消毒处理的空白对照组,分别进行生物力学测试,对测量结果行统计学比较分析。结果:高压蒸汽消毒后,韧带所能承受的最大拉力及第一次破裂力降低,且与对照组间的差异均有统计学意义(P<0.05);60Co照射消毒后,韧带所能承受的最大拉力降低,与对照组间的差异有统计学意义(P<0.05),但第一次破裂力的差异不明显(P>0.05);环氧乙烷消毒处理后,最大拉力、第一次破裂力与对照组之间无明显差异(P>0.05);各组间断裂伸长率无明显差异(P>0.05)。结论:高压蒸汽消毒后韧带样品的生物力学性能降低比较明显;采用60Co射线消毒方法对产品的力学性能影响较小,但进一步的消毒方法改进可能更为理想;环氧乙烷消毒法可作为生物化PET人工韧带的有效消毒方法。     

Sterilization of epidermal growth factor with supercritical carbon dioxide and peracetic acid; analysis of changes at the amino acid and protein level

Aseptic processing and terminal sterilization become increasingly challenging as medical devices become more complex and include active biologics. Terminal sterilization is preferred for patient safety and production costs. We aimed to determine how sterilization using supercritical CO₂ (scCO₂) with low levels of peracetic acid (PAA) affects amino acids and human epidermal growth factor (EGF) as a model protein. In a benchtop reactivity test, the amino acids methionine, tryptophan, arginine and lysine reacted with low levels of PAA in solution. At PAA levels used for scCO₂ sterilization, however, mass spectrometry only identified oxidative adducts on methionine and tryptophan. Mass spectrometry analysis of EGF exposed to scCO₂/PAA identified oxidative adducts on residues Met₂₁, Trp₄₉ and Trp₅₀, as well as a low level of truncations after residues Trp₄₉ and Trp₅₀. Importantly, processing of EGF in solution with scCO₂ did not affect its native conformation, and sterilized EGF maintained its activity in cell proliferation assays. When processing samples in lyophilized form with scCO₂/PAA, amino acids did not react with PAA and the presence of adducts was strongly reduced on methionine and tryptophan, both as single amino acids and in EGF. Truncation after tryptophan residues did not occur. EGF sterilized in the lyophilized form retained its activity when processing occurred with added moisture. These results have significant implications for the maintenance of biological function in sterilized decellularized scaffolds and the ability to manufacture terminally sterilized combination devices containing therapeutic peptides or proteins.     

Development of a bacteriophage model system to investigate virus inactivation methods used in the treatment of bone allografts

Bone allografts are commonly used in a variety of surgical procedures, to reconstruct lost bone stock and to provide mechanical support during the healing process. Due to concerns regarding the possibility of disease transmission from donor to recipient, and of contamination of grafts during retrieval and processing procedures, it is common practice to sterilise bone allografts prior to issue for clinical use. It is vital that the sterilisation processes applied to allografts are validated to demonstrate that they achieve the required level of bioburden reduction, and by extension that validated models are used for these studies. Two common sterilisation protocols applied to bone allografts are gamma irradiation and ethylene oxide gas sterilisation, and there are currently no validated models available for measuring the anti-viral efficacy of ethylene oxide treatment with regard to bone allografts or readily useable models for assessing the anti-viral efficiency of gamma irradiation treatment. We have developed and validated models for both these sterilisation processes, using the bacteriophage ϕ×174, and utilised the models to measure the antiviral activity of the standard ethylene oxide and gamma irradiation sterilisation processes applied to bone allografts by the National Blood Service. For the irradiation model, we also utilised bacterial spores (Bacillus pumilus). Our results show that ethylene oxide sterilisation (which can only be applied to lyophilised grafts) inactivated >6.1log₁₀ of the model virus, and gamma irradiation (at 25–40 kGy and applied to frozen allografts) inactivated 3.6–4.0log₁₀ of the model virus and >4log₁₀ of the bacterial spores. Gamma irradiation at this dosage is therefore not in itself a sterilisation process with respect to viruses.     

Microbial Growth under Supercritical CO2

Growth of microorganisms in environments containing CO₂ above its critical point is unexpected due to a combination of deleterious effects, including cytoplasmic acidification and membrane destabilization. Thus, supercritical CO₂ (scCO₂) is generally regarded as a sterilizing agent. We report isolation of bacteria from three sites targeted for geologic carbon dioxide sequestration (GCS) that are capable of growth in pressurized bioreactors containing scCO₂. Analysis of 16S rRNA genes from scCO₂ enrichment cultures revealed microbial assemblages of varied complexity, including representatives of the genus Bacillus. Propagation of enrichment cultures under scCO₂ headspace led to isolation of six strains corresponding to Bacillus cereus, Bacillus subterraneus, Bacillus amyloliquefaciens, Bacillus safensis, and Bacillus megaterium. Isolates are spore-forming, facultative anaerobes and capable of germination and growth under an scCO₂ headspace. In addition to these isolates, several Bacillus type strains grew under scCO₂, suggesting that this may be a shared feature of spore-forming Bacillus spp. Our results provide direct evidence of microbial activity at the interface between scCO₂ and an aqueous phase. Since microbial activity can influence the key mechanisms for permanent storage of sequestered CO₂ (i.e., structural, residual, solubility, and mineral trapping), our work suggests that during GCS microorganisms may grow and catalyze biological reactions that influence the fate and transport of CO₂ in the deep subsurface.     

Sterilization of sealed PVDF pouches containing decellularized scaffold by electrical stimulation

A terminal sterilization process for tissue engineering products, such as allografts and biomaterials is necessary to ensure complete removal of pathogenic microorganisms such as the bacteria, fungi, and viruses. However, it can be difficult to sterilize allografts and artificial tissue models packaged in wet conditions without deformation. In this study, we investigated the sterilization effects of electrical stimulation (ES) and assessed its suitability by evaluating sterility assurance levels in pouches at a constant current. Stability of polyvinylidene fluoride pouches was determined by a sterility test performed after exposure to five microorganisms (Staphylococcus aureus, Bacillus subtilis, Pseudomonas aeruginosa, Escherichia coli, and Candida albicans) for 5 days; the sterility test was also performed with decellularized human dermal tissues inoculated with the five microorganisms. Sterilization using ES inactivated microorganisms both inside and outside of sealed pouches and caused no damage to the packaged tissue. Our results support the development of a novel system that involves ES sterilization for packaging of implantable biomaterials and human derived materials.     

Microbiological Aspects of Ethylene Oxide Sterilization: I. Experimental Apparatus and Methods

A specially built thermochemical death-rate apparatus is described which can be used to determine the resistance of microorganisms to ethylene oxide under controlled conditions. The apparatus was designed to provide instantaneous exposure of microorganisms to ethylene oxide and to eliminate variables that could result in errors when death kinetic reaction rates are calculated. The apparatus is used to obtain ethylene oxide resistance data which are useful in evaluating and developing sterilizing cycles for materials with known bacterial concentrations, as well as for calculating probability factors on which a given test condition can be expected to provide sterilization.     

Effects of sterilization treatments on some properties of alginate solutions and gels.

Aqueous sodium alginate solutions were subjected to various heat sterilization treatments. Sodium alginate powder was also treated by both gamma-irradiation and ethylene oxide sterilization. The effects of these treatments on the viscosities of sodium alginate solutions and both the diameter and strength of the beads formed in 0.1 M CaCl2 solutions were determined quantitatively. The viscosity of sodium alginate solutions and the gel strength of the calcium alginate beads decreased with increasing sterilization temperature while the bead diameters were found to increase. All these effects can be attributable to a reduction in the degree of polymerization of the alginate molecules as a result of the heat treatments. Ethylene oxide and gamma-irradiation treatments caused similar effects. Standard conditions for sterilization are necessary for comparative studies with alginate beads.     

Efficient phase separation and product recovery in organic‐aqueous bioprocessing using supercritical carbon dioxide

Biphasic hydrocarbon functionalizations catalyzed by recombinant microorganisms have been shown to be one of the most promising approaches for replacing common chemical synthesis routes on an industrial scale. However, the formation of stable emulsions complicates downstream processing, especially phase separation. This fact has turned out to be a major hurdle for industrial implementation. To overcome this limitation, we used supercritical carbon dioxide (scCO₂) for both phase separation and product purification. The stable emulsion, originating from a stereospecific epoxidation of styrene to (S)‐styrene oxide, a reaction catalyzed by recombinant Escherichia coli, could be destabilized efficiently and irreversibly, enabling complete phase separation within minutes. By further use of scCO₂ as extraction agent, the product (S)‐styrene oxide could be obtained with a purity of 81% (w/w) in one single extraction step. By combining phase separation and product purification using scCO₂, the number of necessary workup steps can be reduced to one. This efficient and easy to use technique is generally applicable for the workup of biphasic biocatalytic hydrocarbon functionalizations and enables a cost effective downstream processing even on a large scale. Biotechnol. Bioeng. 2010;107:642–651. © 2010 Wiley Periodicals, Inc.     

The effect of sterilization on the mechanical properties of intact rabbit humeri in three-point bending, four-point bending and torsion

Load bearing bone allografts are used to replace the mechanical function of bone that has been removed or to augment bone that has been damaged in trauma. In order to minimize the risk of infection and immune response, the bone is delipidated and terminally sterilized prior to implantation. The optimal method for bone graft sterilization has been the topic of considerable research. Recently, supercritical carbon dioxide (SCCO₂) treatments have been shown to terminally sterilize bone against a range of bacteria and viruses. This study aimed to evaluate the effect of SCCO₂ treatment compared with two doses of gamma irradiation, on the mechanical properties of whole bone. Paired rabbit humeri were dissected and randomly assigned into either SCCO₂ control, SCCO₂ additive or gamma irradiation at 10 or 25 kGy treatment groups. The bones were mechanically tested in three-point and four-point bending and torsion, with the lefts acting as controls for the treated rights. Maximum load, energy to failure and stiffness were evaluated. This study found that SCCO₂ treatment with or without additive did not alter maximum load, energy to failure or stiffness significantly under any loading modality. Gamma irradiation had a deleterious dose dependant effect, with statistically significant decreases in all mechanical tests at 25 kGy; while at 10 kGy there were reductions in all loading profiles, though only reaching statistical significance in torsion. This study highlights the expediency of SCCO₂ treatment for bone allograft processing as terminal sterilization can be achieved while maintaining the intrinsic mechanical properties of the graft.     

Limitations of Thioglycolate Broth as a Sterility Test Medium for Materials Exposed to Gaseous Ethylene Oxide

Although ethylene oxide is a reliable sterilizer, the process may be limited by diffusion. Thus, situations may exist where microorganisms are protected from the sterilizing gas. It is possible that the exterior of a substance may be sterilized, whereas the interior is not. We investigated three general types of materials in which this limitation of diffusion could occur: the bore of glass and plastic tubing, the center of cotton balls, and plastic adhesive film/paper backing interface. These materials were contaminated as close to their geometric center as possible with Bacillus subtilis var. niger spores occluded in crystals of sodium chloride. After exposure of the contaminated materials (except aluminum foil) to ethylene oxide, thioglycolate broth (a standard sterility-test medium) indicated sterility, whereas Trypticase Soy Broth indicated nonsterility. It is likewise possible that aerobic microorganisms, surviving in or on material after exposure to dry heat or steam sterilization processes, would not be recovered by thioglycollate broth. Entrapped aerobic organisms will probably not grow out in the low oxygen tension zone of an anaerobic medium such as thioglycollate broth. It is recommended than an aerobic medium such as Trypticase Soy Broth be used concurrently with thioglycolate broth for sterility testing.     

Differentiation of bone marrow-derived mesenchymal stem cells into hepatocyte-like cells in an alginate scaffold

Objectives: Alginate scaffolds are the most frequently investigated biomaterials in tissue engineering. Tissue engineering techniques that generate liver tissue have become important for treatment of a number of liver diseases and recent studies indicate that bone marrow‐derived stem cells (BMSCs) can differentiate into hepatocyte‐like cells. The goal of the study described here, was to examine in vitro hepatic differentiation potential of BMSCs cultured in an alginate scaffold. Materials and methods: To investigate the potential of BMSCs to differentiate into hepatocyte‐like cells, we cultured BMSCs in alginate scaffolds in the presence of specific growth factors including hepatocyte growth factor, epidermal growth factor and fibroblast growth factor‐4. Results: We can demonstrate that alginate scaffolds are compatible for growth of BMSCs and when cultured in alginate scaffolds for several days they display several liver‐specific markers and functions. Specifically, they expressed genes encoding alpha‐foetoprotein, albumin (ALB), connexin 32 and CYP7A1. In addition, these BMSCs produced both ALB and urea, expressed cytokeratin‐18 (CK‐18) and were capable of glycogen storage. Percentage of CK‐18 positive cells, a marker of hepatocytes, was 56.7%. Conclusions: Our three‐dimensional alginate scaffolds were highly biocompatible with BMSCs. Furthermore, culturing induced their differentiation into hepatocyte‐like cells. Therefore, BMSCs cultured in alginate scaffolds may be applicable for hepatic tissue engineering.     

聚合物微流控芯片消毒灭菌技术研究进展

聚合物微流控芯片成本低、易加工,目前在医药、生物检测和化学合成等领域得到了普遍应用。以热塑性聚合物聚甲基丙烯酸甲酯(polymethylmethacrylate,PMMA)和热固型聚合物聚二甲基硅氧烷(polydimethy lsiloxane,PDMS)为基材的高分子聚合物材料因具有较好的生物相容性和光学透明性,已逐渐成为聚合物微流控芯片加工的主导材料,被广泛应用于生物医药类微流控芯片的制备。鉴于该类芯片应用场景的特殊性,需在使用前进行消毒灭菌处理以避免微生物干扰。目前,针对PMMA和PDMS的消毒灭菌方法包括高压蒸汽灭菌、紫外线灭菌、电子束、60Co γ射线辐射灭菌、超临界二氧化碳灭菌、乙醇消毒、环氧乙烷灭菌、过氧化氢低温等离子体灭菌、绿原酸消毒、清洗剂消毒。本文从基本原理、消毒灭菌方法、应用场景等方面,回顾和总结了相关技术在PMMA和PDMS基体微流控芯片中的实现方法,并在芯片材质、适用范围等方面分析了所适用的消毒灭菌方法,为以聚合物为基材的生物医药类微流控芯片的消毒灭菌提供有益参考。     

X-ray sterilization of biopharmaceutical manufacturing equipment—Extractables profile of a film material and copolyester Tritan™ compared to gamma irradiation

The biopharmaceutical industry gains enormous flexibility in production processes by using sterilized preassembled single-use devices. Gamma irradiation is an established sterilization technology that may be restricted in the future by the availability of ⁶⁰Co as irradiation source and irradiation capacities. X-ray technology is considered an alternative type of radiation for sterilizing SU equipment. In the context of extractables and leachables—one concern connected with the use of single-use process equipment—the effect of X-ray irradiation on the extractables profile of the materials needs to be compared to established gamma irradiation to qualify this alternative technology. An approach is presented to obtain robust and comprehensive extractables data for materials used in SU devices after sterilization either using X-ray or gamma irradiation. A careful selection of the test items and the test design allows a one-to-one comparison of data obtained from a combination of orthogonal analytical techniques. The extractables of a modern SU film material and the copolyester Tritan™ are evaluated. The data presented allow a risk evaluation on the safety of this new sterilization modality for biopharmaceutical applications. It is demonstrated that the extractables profile of a polymer is not affected by the type of irradiation used for sterilization.     

Involvement of phospholipase D-related signal transduction in chemical-induced programmed cell death in tomato cell cultures

Phospholipase D (PLD) and its product phosphatidic acid (PA) are incorporated in a complex metabolic network in which the individual PLD isoforms are suggested to regulate specific developmental and stress responses, including plant programmed cell death (PCD). Despite the accumulating knowledge, the mechanisms through which PLD/PA operate during PCD are still poorly understood. In this work, the role of PLDα1 in PCD and the associated caspase-like proteolysis, ethylene and hydrogen peroxide (H₂O₂) synthesis in tomato suspension cells was studied. Wild-type (WT) and PLDα1-silenced cell lines were exposed to the cell death-inducing chemicals camptothecin (CPT), fumonisin B1 (FB1) and CdSO₄. A range of caspase inhibitors effectively suppressed CPT-induced PCD in WT cells, but failed to alleviate cell death in PLDα1-deficient cells. Compared to WT, in CPT-treated PLDα1 mutant cells, reduced cell death and decreased production of H₂O₂ were observed. Application of ethylene significantly enhanced CPT-induced cell death both in WT and PLDα1 mutants. Treatments with the PA derivative lyso-phosphatidic acid and mastoparan (agonist of PLD/PLC signalling downstream of G proteins) caused severe cell death. Inhibitors, specific to PLD and PLC, remarkably decreased the chemical-induced cell death. Taken together with our previous findings, the results suggest that PLDα1 contributes to caspase-like-dependent cell death possibly communicated through PA, reactive oxygen species and ethylene. The dead cells expressed morphological features of PCD such as protoplast shrinkage and nucleus compaction. The presented findings reveal novel elements of PLD/PA-mediated cell death response and suggest that PLDα1 is an important factor in chemical-induced PCD signal transduction.     

Sterilization of Allograft Bone: is 25 kGy the Gold Standard for Gamma Irradiation?

For several decades, a dose of 25 kGy of gamma irradiation has been recommended for terminal sterilization of medical products, including bone allografts. Practically, the application of a given gamma dose varies from tissue bank to tissue bank. While many banks use 25 kGy, some have adopted a higher dose, while some choose lower doses, and others do not use irradiation for terminal sterilization. A revolution in quality control in the tissue banking industry has occurred in line with development of quality assurance standards. These have resulted in significant reductions in the risk of contamination by microorganisms of final graft products. In light of these developments, there is sufficient rationale to re-establish a new standard dose, sufficient enough to sterilize allograft bone, while minimizing the adverse effects of gamma radiation on tissue properties. Using valid modifications, several authors have applied ISO standards to establish a radiation dose for bone allografts that is specific to systems employed in bone banking. These standards, and their verification, suggest that the actual dose could be significantly reduced from 25 kGy, while maintaining a valid sterility assurance level (SAL) of 10⁻⁶. The current paper reviews the methods that have been used to develop radiation doses for terminal sterilization of medical products, and the current trend for selection of a specific dose for tissue banks.     

Electrospun sodium alginate/poly(ethylene oxide) core-shell nanofibers scaffolds potential for tissue engineering applications

Core-shell structure nanofibers of sodium alginate/poly(ethylene oxide) were prepared via electrospinning their dispersions in water solution. The core-shell structure morphology of the obtained nanofibers was viewed under scanning electron microscope (SEM) and transmission electron microscope (TEM), and X-ray photoelectron spectroscopy (XPS) analysis was used to further quantify the chemical composition of the core-shell composite SA/PEO nanofibers surface in detail. Furthermore, one-step cross-linking method through being immersed in CaCl₂ solution was investigated to improve the anti-water property of the electrospun nanofibers mats in order to facilitate their practical applications as tissue engineering scaffolds, and the changes of the structural of nanofibers before and after cross-linking was characterized by Fourier transform infrared (FT-IR). Indirect cytotoxicity assessment indicated that SA/PEO nanofibers membrane was nontoxic to the fibroblasts cells, and cell culture suggested that SA/PEO nanofibers tended to promote fibroblasts cells attachment and proliferation. It was assumed that the nanofibers membrane of electrospun SA/PEO could be used for tissue engineering scaffolds.     

Fine structure and molecular content of human chondrocytes encapsulated in alginate beads

Preservation of the chondrocytic phenotype in vitro requires a 3D (three‐dimensional) culture model. Diverse biomaterials have been tested as scaffolds for culture of animal chondrocytes; however, to date, none is considered a gold standard in regenerative medicine. Here, we studied the fine structure and the GAGs (glycosaminoglycans) content of human chondrocytes encapsulated in alginate beads by using electron microscopy and radioactive sulfate [³⁵S] incorporation, respectively. Cells were obtained from human cartilage, encapsulated in alginate beads and cultured for 28 days. [³⁵S]Na₂SO₄ was added to the culture media and later isolated for quantification of the sulfated GAGs found in three compartments: IC (intracellular), IB (intra‐bead) and EB (extra‐bead). Round cells were seen isolated or forming small groups throughout the alginate. Human chondrocytes presented the features of active cells such as euchromatic nuclei, abundant RER (rough endoplasmic reticulum) and many transport vesicles. We observed an extracellular matrix rich in collagen fibres and electrondense material adjacent to the cells. Most of the GAGs produced (74%) were found in the culture medium (EB), indicating that alginate has a limited capacity to retain the GAGs. CS (chondroitin sulfate), the major component of aggrecan, was the most prominent GAG produced by the encapsulated cells. Human chondrocytes cultured in alginate can sustain their phenotype, confirming the potential application of this biomaterial for cartilage engineering.     

地质封存二氧化碳与深地微生物相互作用研究进展

地质封存将工业和能源相关领域生产活动产生的二氧化碳（CO₂）进行捕集并注入到深部地下岩石构造中,以实现长期储存的目标,是降低温室气体排放、实现CO₂长期封存的重要可行性手段之一。向深部地下地质构造中注入大量CO₂会导致深地环境发生显著变化,进而引起原生微生物活性及群落结构发生明显改变。因此,地质封存CO₂能够直接或间接影响深地微生物驱动的生物地球化学过程。同时,微生物在短期和长期的超临界CO₂（scCO₂）胁迫作用下,也会通过不同的适应性进化方式影响CO₂在地下环境中的迁移、转化和赋存形态。本文介绍了国内外二氧化碳捕获与封存发展现状以及地质封存CO₂影响条件下的scCO₂-水-微生物-矿物的相互作用领域的最新科研进展,并展望了利用深地微生物强化CO₂固定以及将其转化为高附加值产物的潜力。