Fabrication of gelatin nanofibrous scaffolds using ethanol/phosphate buffer saline as a benign solvent

Electrospinning of natural polymer nanofibers useful for biomedical applications often requires the use of cytotoxic organic solvents. In this study, gelatin nanofibers are electrospun from phosphate buffer saline/ethanol binary mixtures as a benign solvent at ambient temperature. The influences of ionic strength, ethanol concentration, and gelatin concentration on the electrospinnability of gelatin solutions and the fiber microarchitectures are analyzed. The electrospun scaffolds retain their morphologies during vapor‐phase crosslinking with glutaraldehyde in ethanol and the subsequent removal of salts contained in the nanofibers via water rinsing. When fully hydrated, the mechanically preconditioned scaffolds display a Young's modulus of 25.5 ± 5.3 kPa, tensile strength of 55.5 ± 13.9 kPa, deformability of 160 ± 15%, and resilience of 89.9 ± 1.8%. When cultured on the gelatin scaffolds, 3T3 fibroblasts displayed spindle‐like morphology, similar to the cell's normal morphology in a 3D extracellular matrix. © 2012 Wiley Periodicals, Inc. Biopolymers 97:1026–1036, 2012.     

A biomimetic tubular scaffold with spatially designed nanofibers of protein/PDS® bio‐blends

Electrospun tubular conduit (4 mm inner diameter) based on blends of polydioxanone (PDS II®) and proteins such as gelatin and elastin having a spatially designed trilayer structure was prepared for arterial scaffolds. SEM analysis of scaffolds showed random nanofibrous morphology and well‐interconnected pore network. Due to protein blending, the fiber diameter was reduced from 800–950 nm range to 300–500 nm range. Fourier‐transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) results confirmed the blended composition and crystallinity of fibers. Pure PDS scaffold under hydrated state exhibited a tensile strength of 5.61 ± 0.42 MPa and a modulus of 17.11 ± 1.13 MPa with a failure strain of 216.7 ± 13%. The blending of PDS with elastin and gelatin has decreased the tensile properties. A trilayer tubular scaffold was fabricated by sequential electrospinning of blends of elastin/gelatin, PDS/elastin/gelatin, and PDS/gelatin (EG/PEG/PG) to mimic the complex matrix structure of native arteries. Under hydrated state, the trilayer conduit exhibited tensile properties (tensile strength of 1.77 ± 0.2 MPa and elastic modulus of 5.74 ± 3 MPa with a failure strain of 75.08 ± 10%) comparable to those of native arteries. In vitro degradation studies for up to 30 days showed about 40% mass loss and increase in crystallinity due to the removal of proteins and “cleavage‐induced crystallization” of PDS. Biotechnol. Bioeng. 2009; 104: 1025–1033. © 2009 Wiley Periodicals, Inc.     

Fabrication of a biomimetic spinal cord tissue construct with heterogenous mechanical properties using intrascaffold cell assembly

In tissue engineering studies, scaffolds play a very important role in offering both physical and chemical cues for cell growth and tissue regeneration. However, in some cases, tissue regeneration requires scaffolds with high mechanical properties (e.g., bone and cartilage), while cells need a soft mechanical microenvironment. In this study, to mimic the heterogenous mechanical properties of a spinal cord tissue, a biomimetic rat tissue construct is fabricated. A collagen-coated poly(lactic-co-glycolic acid) scaffold is manufactured using thermally induced phase separation casting. Primary rat neural cells (P01 Wistar rat cortex) with soft hydrogels are later printed within the scaffold using an image-guided intrascaffold cell assembly technique. The scaffolds have unidirectional microporous structure with parallel axial macrochannels (260 ± 4 µm in diameter). Scaffolds showed mechanical properties similar to rat spine (ultimate tensile strength: 0.085 MPa, Young's modulus [stretch]: 0.31 MPa). The bioink composed of gelatin/alginate/fibrinogen is precisely printed into the macrochannels and showed mechanical properties suitable for neural cells (Young's modulus [compressive]: 3.814 kPa). Scaffold interface, cell viability, and immunostaining analyses show uniform distribution of stable, healthy, and elongated neural cells and neurites over 14 culture days in vitro. The results demonstrated that this method can serve as a valuable tool to aid manufacturing of tissue constructs requiring heterogenous mechanical properties for complex cell and/or biomolecule assembly.     

Nanofibrous nonmulberry silk/PVA scaffold for osteoinduction and osseointegration

Poly‐vinyl alcohol and nonmulberry tasar silk fibroin of Antheraea mylitta are blended to fabricate nanofibrous scaffolds for bone regeneration. Nanofibrous matrices are prepared by electrospinning the equal volume ratio blends of silk fibroin (2 and 4 wt%) with poly‐vinyl alcohol solution (10 wt%) and designated as 2SF/PVA and 4SF/PVA, respectively with average nanofiber diameters of 177 ± 13 nm (2SF/PVA) and 193 ± 17 nm (4SF/PVA). Fourier transform infrared spectroscopy confirms retention of the secondary structure of fibroin in blends indicating the structural stability of neo‐matrix. Both thermal stability and contact angle of the blends decrease with increasing fibroin percentage. Conversely, fibroin imparts mechanical stability to the blends; greater tensile strength is observed with increasing fibroin concentration. Blended scaffolds are biodegradable and support well the neo‐bone matrix synthesis by human osteoblast like cells. The findings indicate the potentiality of nanofibrous scaffolds of nonmulberry fibroin as bone scaffolding material. © 2014 Wiley Periodicals, Inc. Biopolymers 103: 271–284, 2015.     

Potential of Magnetic Nanofiber Scaffolds with Mechanical and Biological Properties Applicable for Bone Regeneration

Magnetic nanofibrous scaffolds of poly(caprolactone) (PCL) incorporating magnetic nanoparticles (MNP) were produced, and their effects on physico-chemical, mechanical and biological properties were extensively addressed to find efficacy for bone regeneration purpose. MNPs 12 nm in diameter were citrated and evenly distributed in PCL solutions up to 20% and then were electrospun into nonwoven nanofibrous webs. Incorporation of MNPs greatly improved the hydrophilicity of the nanofibers. Tensile mechanical properties of the nanofibers (tensile strength, yield strength, elastic modulus and elongation) were significantly enhanced with the addition of MNPs up to 15%. In particular, the tensile strength increase was as high as ∼25 MPa at 15% MNPs vs. ∼10 MPa in pure PCL. PCL-MNP nanofibers exhibited magnetic behaviors, with a high saturation point and hysteresis loop area, which increased gradually with MNP content. The incorporation of MNPs substantially increased the degradation of the nanofibers, with a weight loss of ∼20% in pure PCL, ∼45% in 10% MNPs and ∼60% in 20% MNPs. Apatite forming ability of the nanofibers tested in vitro in simulated body fluid confirmed the substantial improvement gained by the addition of MNPs. Osteoblastic cells favored the MNPs-incorporated nanofibers with significantly improved initial cell adhesion and subsequent penetration through the nanofibers, compared to pure PCL. Alkaline phosphatase activity and expression of genes associated with bone (collagen I, osteopontin and bone sialoprotein) were significantly up-regulated in cells cultured on PCL-MNP nanofibers than those on pure PCL. PCL-MNP nanofibers subcutaneously implanted in rats exhibited minimal adverse tissue reactions, while inducing substantial neoblood vessel formation, which however, greatly limited in pure PCL. In vivo study in radial segmental defects also signified the bone regeneration ability of the PCL-MNP nanofibrous scaffolds. The magnetic, bone-bioactive, mechanical, cellular and tissue attributes of MNP-incorporated PCL nanofibers make them promising candidate scaffolds for bone regeneration.     

Nanostructured biocomposite scaffolds based on collagen coelectrospun with nanohydroxyapatite

Nanofibrous biocomposite scaffolds of type I collagen and nanohydroxyapatite (nanoHA) of varying compositions (wt %) were prepared by electrostatic cospinning. The scaffolds were characterized for structure and morphology by Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) techniques. The scaffolds have a porous nanofibrous morphology with random fibers in the range of 500-700 nm diameters, depending on the composition. FT-IR and XRD showed the presence of nanoHA in the fibers. The surface roughness and diameter of the fibers increased with the presence of nanoHA in biocomposite fiber as evident from AFM images. Tensile testing and nanoindendation were used for the mechanical characterization. The pure collagen fibrous matrix (without nanoHA) showed a tensile strength of 1.68 +/- 0.10 MPa and a modulus of 6.21 +/- 0.8 MPa with a strain to failure value of 55 +/- 10%. As the nanoHA content in the randomly oriented collagen nanofibers increased to 10%, the ultimate strength increased to 5 +/- 0.5 MPa and the modulus increased to 230 +/- 30 MPa. The increase in tensile modulus may be attributed to an increase in rigidity over the pure polymer when the hydroxyapatite is added and/or the resulting strong adhesion between the two materials. The vapor phase chemical crosslinking of collagens using glutaraldehyde further increased the mechanical properties as evident from nanoindentation results. A combination of nanofibrous collagen and nanohydroxyapatite that mimics the nanoscale features of the extra cellular matrix could be promising for application as scaffolds for hard tissue regeneration, especially in low or nonload bearing areas.     

Decoration of electrical conductive polyurethane-polyaniline/polyvinyl alcohol matrixes with mussel-inspired polydopamine for bone tissue engineering

Electrospinning is a versatile technology for the fabrication of nanofibrous matrixes to regenerate defects. This study aims to develop a functionalized and electroconductive polymeric matrix to improve rat bone marrow mesenchymal stem cell adhesion, proliferation, and differentiation. Herein, the influence of the chemical composition of the substrate on homogeneous modification of the surface with mussel-inspired polydopamine (PDA) is focused. Accordingly, the deposition of PDA on the surface was proved by Fourier transform infrared spectroscopy. Morphologies of the scaffolds demonstrated homogeneous decoration of the polyvinyl alcohol (PVA)/polyurethane (PU)-polyaniline (PANI) matrixes with PDA, while a lower density of mussel-inspired polymer was observed in bare PU-PANI constructs. Although uniform and dense precipitation of PDA reduced conductivity of scaffolds 1.2 times compared with the samples with a low density of the PDA, 1.1 and 1.2 times enhancement in tensile strength and Young's modulus, respectively, were the strength of the applied process, especially in bone tissue engineering area. Contact angle measurements demonstrated about two times reduction in measured values, which shows improvement in hydrophilicity of PDA-modified PVA/PU-PANI fibers compared with PDA-coated PU-PANI ones. Swelling ratio and mass loss ratio calculations revealed enhancement in measured values as a function of homogeneous and dense coating, which arise from hydrophilicity of the polymeric substrate. The bioactivity test indicated that a dense layer of PDA strongly supports formations of hydroxyapatite-like crystals. Moreover, homogeneous decoration of conductive matrixes with PDA showed suitable cell viability, adhesion, and spreading while cell-scaffolds interactions improved under electrical stimulation. Higher expression of alkaline phosphatase and secretion of Collagen I under the electrical field proved the applicability of modified electroconductive scaffolds for further preclinical and clinical studies to introduce as a reconstructive bone substitute.     

Electrospun poly (ɛ-caprolactone)/silk fibroin core-sheath nanofibers and their potential applications in tissue engineering and drug release

One of the key tenets of tissue engineering is to develop scaffold materials with favorable biodegradability, surface properties, outstanding mechanical strength and controlled drug release property. In this study, we generated core-sheath nanofibers composed of poly (?-caprolactone) (PCL) and silk fibroin (SF) blends via emulsion electrospinning. Nanofibrous scaffolds were characterized by combined techniques of scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), contact angle and tensile measurements. An in vitro FITC release study was conducted to evaluate sustained release potential of the core-sheath structured nanofibers. We found that the conformation of SF contained in PCL/SF composite nanofibers was transformed from random coil to β-sheet when treated with methanol, leading to improved crystallinity and tensile strength of nanofibrous scaffolds. The hydrophobicity and diameter of nanofibers decreased when we increased the content of SF in PCL/SF composite nanofibers. Furthermore, we evaluated the potential of fabricated PCL/SF composite nanofibers as scaffold in vitro. The results confirmed that fabricated PCL/SF scaffolds improved cell attachment and proliferation. Our results demonstrated the feasibility to generate core-sheath nanofibers composed of PCL and SF using a single-nozzle technique. The produced nanofibrous scaffolds with sustained drug release have potential application in tissue engineering.     

Mechanical response of porous scaffolds for cartilage engineering

Mechanical properties of scaffolds seeded with mesenchymal stem cells used for cartilage repair seem to be one of the critical factors in possible joint resurfacing. In this paper, the effect of adding hyaluronic acid, hydroxyapatite nanoparticles or chitosan nanofibers into the cross-linked collagen I on the mechanical response of the lyophilized porous scaffold has been investigated in the dry state at 37 oC under tensile loading. Statistical significance of the results was evaluated using ANOVA analysis. The results showed that the addition of hyaluronic acid significantly (p<0.05) reduced the tensile elastic modulus and enhanced the strength and deformation to failure of the modified cross-linked collagen I under the used test conditions. On the other hand, addition of hydroxyapatite nanoparticles and chitosan nanofibers, respectively, increased the elastic modulus of the modified collagen ten-fold and four-fold, respectively. Hydroxyapatite caused significant reduction in the ultimate deformation at break while chitosan nanofibers enhanced the ultimate deformation under tensile loading substantially (p<0.05). The ultimate tensile deformation was significantly (p<0.05) increased by addition of the chitosan nanofibers. The enhanced elastic modulus of the scaffold was translated into enhanced resistance of the porous scaffolds against mechanical load compared to scaffolds based on cross-linked neat collagen or collagen with hyaluronic acid with similar porosity. It can be concluded that enhancing the rigidity of the compact scaffold material by adding rigid chitosan nanofibers can improve the resistance of the porous scaffolds against compressive loading, which can provide more structural protection to the seeded mesenchymal stem cells when the construct is implanted into a lesion. Moreover, scaffolds with chitosan nanofibers seemed to enhance cell growth compared to the neat collagen I when tested in vitro as well as the scaffold stability, extending its resorption to more than 10 weeks.     

Radiation-induced biomimetic modification of dual-layered nano/microfibrous scaffolds for vascular tissue engineering

One of the interesting strategies for developing the artificial blood vessels is to generate multi-layered scaffolds for mimicking the structure of native blood vessels such as the intima, media, and adventitia. In this study, we prepared dual-layered poly(L-lactide-co-?-caprolactone) (PLCL) scaffolds with micro- and nanofibers as a basic construct of the vessel using electrospinning methods, which was functionalized using a gelatin through acrylic acid (AAc) grafting by γ-ray irradiation. Based on the microfibrous platform (fiber diameter 5 μm), the thickness of the nanofibrous layer (fiber diameter 700 nm) was controlled from 1.1 ± 0.8 to 32.2 ± 1.7 μm, and the mechanical property of the scaffolds was almost maintained despite the increase in thickness of the nanofibrous layer. The successful AAc graft by γ-ray irradiation could allow the gelatin immobilization on the scaffolds. The proliferation of smooth muscle cells (SMC) on the scaffolds toward a microfibrous layer was approximately 1.3-times greater than in the other groups, and the infiltration was significantly increased, presenting a wide cell distribution in the cross-section. In addition, human umbilical vein endothelial cell (HUVEC) adhesion toward nanofibrous layer was well-managed over the entire surface, and the accelerated proliferation was observed on the gelatin-functionalized scaffolds presenting the well-organized gap-junctions. Therefore, our biomimetic dual-layered scaffolds may be the alternative tools for replacing the damaged blood vessels.     

Three-dimensional electrospun gelatin scaffold coseeded with embryonic stem cells and sertoli cells: A promising substrate for in vitro coculture system

In this study, we present an electrospun gelatin (EG) scaffold to mimic the extracellular matrix of the testis. The EG scaffold was synthesized by electrospinning and crosslinked with glutaraldehyde vapor to decrease its water solubility and degradation rate. The scanning electron microscope micrographs showed the homogenous morphology of randomly aligned gelatin fibers. The average diameter of gelatin fibers before and after crosslinking was approximately 180 and 220 nm, respectively. Modulus, tensile strength, and elongation at break values were as 161.8 ± 24.4 MPa, 4.21 ± 0.54 MPa, and 7.06 ± 2.12 MPa, respectively. The crosslinked EG showed 75.2% ± 4.5% weight loss after 14 days with no changes in the pH value of degradation solution. Cytobiocompatibility of the EG for sertoli cells and embryonic stem cells (ESCs) was determined in vitro. Sertoli cells were isolated from mouse testis and characterized by immunostaining and flow cytometry. The effects of EG on proliferation and attachment of both sertoli cells and ESCs were examined. The EG scaffolds exhibited no cytotoxicity for sertoli and ESCs. Both sertoli and ESCs were well attached and grown on EG. Coculture of sertoli and ESCs on EG showed better ESCs adhesion compared with ESCs alone. Our findings indicate the potential of EG as a substrate for proliferation, adhesion, and coculture of sertoli and ESCs and may be considered as a promising engineered microenvironment for in vitro coculture system with the aim of guiding stem cells differentiation toward sperm-producing cells.     

Electrospun core-shell nanofibers from homogeneous solution of poly(vinyl alcohol)/bovine serum albumin

We report on the preparation and characterization of core-shell structure of bovine serum albumin (BSA) blended poly(vinyl alcohol) (PVA) composite nanofibers by using electrospinning process. The core-shell structure nanofibers have been electrospun from the homogeneous solution of BSA (as shell) and PVA (as core). The morphology, chemical compositions, structure and thermal properties of the resultant products were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDX), high-resolution transmission electron microscopy (HR-TEM), Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry, thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS) techniques. The blending ratio of PVA and BSA, molecular weight of BSA and the applied voltage of electrospinning process were observed to be the key influence factors on the formation of core-shell nanofibers structure. Based on the experimental findings, we proposed a possible physical mechanism for the formation of core-shell nanofibers structure of PVA blended BSA composite.     

Shear stress magnitude and duration modulates matrix composition and tensile mechanical properties in engineered cartilaginous tissue

Cartilage tissue‐engineering strategies aim to produce a functional extracellular matrix similar to that of the native tissue. However, none of the myriad approaches taken have successfully generated a construct possessing the structure, composition, and mechanical properties of healthy articular cartilage. One possible approach to modulating the matrix composition and mechanical properties of engineered tissues is through the use of bioreactor‐driven mechanical stimulation. In this study, we hypothesized that exposing scaffold‐free cartilaginous tissue constructs to 7 days of continuous shear stress at 0.001 or 0.1 Pa would increase collagen deposition and tensile mechanical properties compared to that of static controls. Histologically, type II collagen staining was evident in all construct groups, while a surface layer of type I collagen increased in thickness with increasing shear stress magnitude. The areal fraction of type I collagen was higher in the 0.1‐Pa group (25.2 ± 2.2%) than either the 0.001‐Pa (13.6 ± 3.8%) or the static (7.9 ± 1.5%) group. Type II collagen content, as assessed by ELISA, was also higher in the 0.1‐Pa group (7.5 ± 2.1%) compared to the 0.001‐Pa (3.0 ± 2.25%) or static groups (3.7 ± 3.2%). Temporal gene expression analysis showed a flow‐induced increase in type I and type II collagen expression within 24 h of exposure. Interestingly, while the 0.1‐Pa group showed higher collagen content, this group retained less sulfated glycosaminoglycans in the matrix over time in bioreactor culture. Increases in both tensile Young's modulus and ultimate strength were observed with increasing shear stress, yielding constructs possessing a modulus of nearly 5 MPa and strength of 1.3 MPa. This study demonstrates that shear stress is a potent modulator of both the amount and type of synthesized extracellular matrix constituents in engineered cartilaginous tissue with corresponding effects on mechanical function. Biotechnol. Bioeng. 2009; 104: 809–820 © 2009 Wiley Periodicals, Inc.     

Synthesis of Keratin-based Nanofiber for Biomedical Engineering

Electrospinning, due to its versatility and potential for applications in various fields, is being frequently used to fabricate nanofibers. Production of these porous nanofibers is of great interest due to their unique physiochemical properties. Here we elaborate on the fabrication of keratin containing poly (ε-caprolactone) (PCL) nanofibers (i.e., PCL/keratin composite fiber). Water soluble keratin was first extracted from human hair and mixed with PCL in different ratios. The blended solution of PCL/keratin was transformed into nanofibrous membranes using a laboratory designed electrospinning set up. Fiber morphology and mechanical properties of the obtained nanofiber were observed and measured using scanning electron microscopy and tensile tester. Furthermore, degradability and chemical properties of the nanofiber were studied by FTIR. SEM images showed uniform surface morphology for PCL/keratin fibers of different compositions. These PCL/keratin fibers also showed excellent mechanical properties such as Young''s modulus and failure point. Fibroblast cells were able to attach and proliferate thus proving good cell viability. Based on the characteristics discussed above, we can strongly argue that the blended nanofibers of natural and synthetic polymers can represent an excellent development of composite materials that can be used for different biomedical applications.     

Silk–PVA Hybrid Nanofibrous Scaffolds for Enhanced Primary Human Meniscal Cell Proliferation

In this study, silk fibroin nanofibrous scaffolds were developed to investigate the attachment and proliferation of primary human meniscal cells. Silk fibroin (SF)–polyvinyl alcohol (PVA) blended electrospun nanofibrous scaffolds with different blend ratios (2:1, 3:1, and 4:1) were prepared. Morphology of the scaffolds was characterized using atomic force microscopy (AFM). The hybrid nanofibrous mats were crosslinked using 25 % (v/v) glutaraldehyde vapor. In degradation study, the crosslinked nanofiber showed slow degradation of 20 % on weight after 35 days of incubation in simulated body fluid (SBF). The scaffolds were characterized with suitable techniques for its functional groups, porosity, and swelling ratio. Among the nanofibers, 3:1 SF:PVA blend showed uniform morphology and fiber diameter. The blended scaffolds had fluid uptake and swelling ratio of 80 % and 458 ± 21 %, respectively. Primary meniscal cells isolated from surgical debris after meniscectomy were subcultured and seeded onto these hybrid nanofibrous scaffolds. Meniscal cell attachment studies confirmed that 3:1 SF:PVA nanofibrous scaffolds supported better cell attachment and growth. The DNA and collagen content increased significantly with 3:1 SF:PVA. These results clearly indicate that a blend of SF:PVA at 3:1 ratio is suitable for meniscus cell proliferation when compared to pure SF-PVA nanofibers.     

Novel CaO/polylactic acid nanoscaffold as dental resin nanocomposites and the investigation of physicochemical properties

In this study, for the first time, calcium oxide (CaO)/polylactic acid nanoscaffolds were synthesized by co‐precipitation assistant reverse micelles method. The physical and chemical (physicochemical) properties of the structures as dental resin composites were also studied. Nanocomposite materials as primary and basic dental compounds can be conveniently applied as dental filling materials with a high esthetic quality. In this research nanoscaffolds act as a bed for nanoparticles and improve the mechanical and chemical (mechanochemical) properties, CaO nanoparticles were loading in polylactic acid nanoscaffold as a bioactivity polymer for usage in the dental resin composites. Mechanical properties of the dental resin composite containing CaO/polylactic acid nanoscaffold were calculated: the flexural strength (137.2 MPa), modulus (12.9GPa) and compressive strength (344.2 MPa). Potential of the basic nanoparticle and the products were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), dynamic light scattering (DLS), ultraviolet‐visible spectroscopy (UV‐visible) and atomic force microscopy (AFM) showed the size of the optimized nanostructures was about 85 to 120 nm. According to TGA results of polylactic acid nanofibers with thermal stability below 300°C these high thermal stability materials can be used as dental resin composites.     

Effect of adding nano‐titanium dioxide on the microstructure,mechanical properties and in vitro bioactivity of a freeze cast merwinite scaffold

In the present research, merwinite (M) scaffolds with and without nano‐titanium dioxide (titania) were synthesized by water‐based freeze casting method. Two different amounts (7.5 and 10 wt%) of n‐TiO₂ were added to M scaffolds. They were sintered at temperature of 1573.15°K and at cooling rate of 4°K/min. The changes in physical and mechanical properties were investigated. The results showed that although M and M containing 7.5 wt% n‐TiO₂ (MT7.5) scaffolds had approximately the same microstructures in terms of pore size and wall thickness, these factors were different for sample MT10. In overall, the porosity, volume and linear shrinkage were decreased by adding different weight ratios of n‐TiO₂ into the M structure. According to the obtained mechanical results, the optimum mechanical performance was related to the sample MT7.5 (E = 51 MPa and σ = 2 MPa) with respect to the other samples, i.e.: M (E = 47 MPa and σ = 1.8 MPa) and MT10 (E = 32 MPa and σ = 1.4 MPa). The acellular in vitro bioactivity experiment confirmed apatite formation on the surfaces of all samples for various periods of soaking time. Based on cell study, the sample which possessed favorable mechanical behavior (MT7.5) supported attachment and proliferation of osteoblastic cells. These results revealed that the MT7.5 scaffold with improved mechanical and biological properties could have a potential to be used in bone substitute. © 2015 American Institute of Chemical Engineers Biotechnol. Prog., 31:550–556, 2015     

Influence of kepok banana bunch as new cellulose source on thermal,mechanical, and biodegradability properties of Thai cassava starch/polyvinyl alcohol hybrid-based bioplastic

Bioplastics were developed to overcome environmental problems that are difficult to decompose in the environment. This study analyzes Thai cassava starch-based bioplastics' tensile strength, biodegradability, moisture absorption, and thermal stability. This study used Thai cassava starch and polyvinyl alcohol (PVA) as matrices, whereas Kepok banana bunch cellulose was employed as a filler. The ratios between starch and cellulose are 10:0 (S1), 9:1 (S2), 8:2 (S3), 7:3 (S4), and 6:4 (S5), while PVA was set constant. The tensile test showed the S4 sample's highest tensile strength of 6.26 MPa, a strain of 3.85%, and a modulus of elasticity of 166 MPa. After 15 days, the maximum soil degradation rate in the S1 sample was 27.9%. The lowest moisture absorption was found in the S5 sample at 8.43%. The highest thermal stability was observed in S4 (316.8°C). This result was significant in reducing the production of plastic waste for environmental remediation.     

Novel hybrid scaffolds for the cultivation of osteoblast cells

In this study, natural biodegradable polysaccharide, chitosan, and synthetic biodegradable polymer, poly(?-caprolactone) (PCL) were used to prepare 3D, hybrid polymeric tissue scaffolds (PCL/chitosan blend and PCL/chitosan/PCL layer by layer scaffolds) by using the electrospinning technique. The hybrid scaffolds were developed through HA addition to accelerate osteoblast cell growth. Characteristic examinations of the scaffolds were performed by micrometer, SEM, contact angle measurement system, ATR-FTIR, tensile machine and swelling experiments. The thickness of all electrospun scaffolds was determined in the range of 0.010 ± 0.001-0.012 ± 0.002 mm. In order to optimize electrospinning processes, suitable bead-free and uniform scaffolds were selected by using SEM images. Blending of PCL with chitosan resulted in better hydrophilicity for the PCL/chitosan scaffolds. The characteristic peaks of PCL and chitosan in the blend and layer by layer nanofibers were observed. The PCL/chitosan/PCL layer by layer structure had higher elastic modulus and tensile strength values than both individual PCL and chitosan structures. The layer by layer scaffolds exhibited the PBS absorption values of 184.2; 197.2% which were higher than those of PCL scaffolds but lower than those of PCL/chitosan blend scaffolds. SaOs-2 osteosarcoma cell culture studies showed that the highest ALP activities belonged to novel PCL/chitosan/PCL layer by layer scaffolds meaning better cell differentiation on the surfaces.     

Mechanical properties of films and three-dimensional scaffolds made of fibroin and gelatin

Silk fibroin is a biocompatible and biodegradable material, which can be used in surgery and tissue engineering. To improve the cell adhesion on fibroin surface, gelatin can be added to the items made of fibroin. This work compares the mechanical properties of films and three-dimensional scaffolds made of fibroin and fibroin with gelatin. The addition of 30% gelatin to the fibroin scaffold does not change its microstructure or swelling. The addition of gelatin decreases the mechanical properties of films (decreases the Young’s modulus, the maximum strain and elongation) but increases the shear modulus of the scaffolds.