Chitin/chitosan transformation by thermo-mechano-chemical treatment including characterization by enzymatic depolymerization

Chitosan, the deacetylated derivative of chitin, was until recently produced by hydrolysis in 50% (w/v) NaOH. Application of thermo-mechano-chemical technology to chitin deacetylation was evaluated as an alternative method of chitosan production. This process consists of a cascade reactor unit operating under reduced alkaline conditions of 10% (w/v) NaOH. Prior mercerization of chitin at 4 degrees C for 24 h was required for high deacetylation yields. Sudden decompression of the aqueous alkaline suspension of mercerized chitin resulted in near complete deacetylation of chitin. Reactor residence time was 90 s at 230 degrees C prior to decompression. The chitosan produced was characterized by elemental analysis, (13)C-NMR and enzymatic depolymerization. Enzymatic determination of the degree of acetylation of chitin/chitosan mixtures was also investigated. Relative chitinase and/or chitosanase digestibilities were shown to be strongly dependent on chitin deacetylation. Based on enzymatic digestibilities, the alkaline aqueous high shear process does not appear to produce significant secondary products. Correlation of chitosanase digestibility with percentage of deacetylation provides a simple biological assay to study chitosan composition.     

绿色木霉粗纤维素酶液水解壳聚糖的研究

利用自制绿色木霉粗纤维素酶液降解壳聚糖制备低聚壳聚糖.采用粘度法、乙酰丙酮法和还原糖浓度分析,研究了温度、pH值及反应时间等因素对壳聚糖水解程度和产物相对分子质量的影响,并采用质谱法对水解产物进行定性分析.结果表明,粗纤维素酶液水解壳聚糖作用的最适pH为5.0、最适反应温度为50 ℃、最适反应时间为12 h.粗纤维素酶...     

High yield production of monomer-free chitosan oligosaccharides by pepsin catalyzed hydrolysis of a high deacetylation degree chitosan

The high molecular weight of chitosan, which results in a poor solubility at neutral pH values and high viscosity aqueous solutions, limits its potential uses in the fields of food, health and agriculture. However, most of these limitations are overcome by chitosan oligosaccharides obtained by enzymatic hydrolysis of the polymer. Several commercial enzymes with different original specificities were assayed for their ability to hydrolyze a 93% deacetylation degree chitosan and compared with a chitosanase. According to the patterns of viscosity decrease and reducing end formation, three enzymes--cellulase, pepsin and lipase A--were found to be particularly suitable for hydrolyzing chitosan at a level comparable to that achieved by chitosanase. Unlike the appreciable levels of both 2-amino-2-deoxy-D-glucose and 2-acetamido-2-deoxy-D-glucose monomers released from chitosan by the other enzymes after a 20h-hydrolysis (4.6-9.1% of the total product weight), no monomer could be detected following pepsin cleavage. As a result, pepsin produced a higher yield of chitosan oligosaccharides than the other enzymes: 52% versus as much as 46%, respectively. Low molecular weight chitosans accounted for the remaining 48% of hydrolysis products. The calculated average polymerization degree of the products released by pepsin was around 16 units after 20h of hydrolysis. This product pattern and yield are proposed to be related to the bond cleavage specificity of pepsin and the high deacetylation degree of chitosan used as substrate. The optimal reaction conditions for hydrolysis of chitosan by pepsin were 40 degrees C and pH 4.5, and an enzyme/substrate ratio of 1:100 (w/w) for reactions longer than 1h.     

The degree of acetylation of chitins by gas chromatography and infrared spectroscopy

Gas chromatography of a number of amines, alcohols and sulfur derivatives was carried out on chitin and partially deacetylated chitins as well as on chitosan. The retention time of methanol is proportional to the degree of acetylation, and therefore a method is proposed for the gas-chromatographic determination of the degree of acetylation of chitin/chitosan. The analysis of the infrared spectra of chitin/chitosan also permits one to determine the degree of acetylation by using the ratio of the bands 1550 and 2878 cm^?1.     

Development of rapid screening method for low-yielding chitosanase activity using Remazol Brilliant Blue-chitosan as substrate

Chitosanolytic activity was monitored using chitosan impregnated with Remazol Brilliant Blue R dye (RBB). Low-yielding chitosan (1%, w/v) hydrolysis was modelled using Viscozyme^® L (50%, w/w), a commercial mixed-glucanase, and was found to perform optimally at pH 4.5 and 50 °C. The chitosanase assay was performed on powdered (RBB-P) and colloidal form (RBB-C) of the dyed chitosan. Hydrolysis of chitosan was accompanied by the release of water-soluble dyed-hydrolysate, which can be monitored rapidly using microplate reader at 595 nm. The result obtained from this method was in agreement with the determination of reducing end by using the traditional, complex and time-consuming DNS method. The method is significantly rapid and more sensitive than DNS method.     

Determination of deacetylation degree of chitosan: a comparison between conductometric titration and CHN elemental analysis

Chitosan is a polysaccharide used in a broad range of applications. Many of its unique properties come from the presence of amino groups in its structure. A proper quantification of these amino groups is very important, in order to specify if a given chitosan sample can be used in a particular application. In this work, a comparison between the determination of chitosan degree of deacetylation by conductometry and CHN elemental analysis was carried out, using a rigorous error analysis. Accurate expressions relating CHN composition, conductometric titration, and degree of deacetylation, in conjunction with their associated errors, were developed and reported in this note. Error analysis showed conductometric analysis as an inexpensive and secure method for the determination of the degree of deacetylation of chitosan.     

Preparation of low-molecular-weight chitosan using phosphoric acid

Two types of low degree of polymerisation (DP) chitosan were prepared by homogeneous hydrolysis of chitosan in 85% phosphoric acid at room temperature for 1–6 weeks. The hydrolysates were collected by addition of excess ethanol, and were fractionated by solubility in water. The changes in yields of water-insoluble (higher DP) and water-soluble (lower DP) fractions were determined as a function of hydrolysis time. The hydrolysis proceeded with further deacetylation of chitosan, resulting in degree of deacetylation of more than 90%. The water-insoluble fraction prepared after the hydrolysis for 4 weeks (43% yield) had a weight-average DP ( ) of 16·8, and showed the ‘tendon’ type X-ray diffraction pattern. The water-soluble fraction (12·5% yield) had a of 7·3, and showed the ‘annealed’ type pattern.     

Biochemical and molecular characterization of a thermostable chitosanase produced by the strain Paenibacillus sp. 1794 newly isolated from compost

Chitosan raises a great interest among biotechnologists due to its potential for applications in biomedical or environmental fields. Enzymatic hydrolysis of chitosan is a recognized method allowing control of its molecular size, making possible its optimization for a given application. During the industrial hydrolysis process of chitosan, viscosity is a major problem; which can be circumvented by raising the temperature of the chitosan solution. A thermostable chitosanase is compatible with enzymatic hydrolysis at higher temperatures thus allowing chitosan to be dissolved at higher concentrations. Following an extensive micro-plate screening of microbial isolates from various batches of shrimp shells compost, the strain 1794 was characterized and shown to produce a thermostable chitosanase. The isolate was identified as a novel member of the genus Paenibacillus, based on partial 16S rDNA and rpoB gene sequences. Using the chitosanase (Csn1794) produced by this strain, a linear time course of chitosan hydrolysis has been observed for at least 6 h at 70 °C. Csn1794 was purified and its molecular weight was estimated at 40 kDa by SDS-PAGE. Optimum pH was about 4.8, the apparent K _m and the catalytic constant k_cat were 0.042 mg/ml and 7,588 min^?1, respectively. The half-life of Csn1794 at 70 °C in the presence of chitosan substrate was >20 h. The activity of chitosanase 1794 varied little with the degree of N-acetylation of chitosan. The enzyme also hydrolyzed carboxymethylcellulose but not chitin. Chitosan or cellulose-derived hexasaccharides were cleaved preferentially in a symmetrical way (“3?+?3”) but hydrolysis rate was much faster for (GlcN)₆ than (Glc)₆. Gene cloning and sequencing revealed that Csn1794 belongs to family 8 of glycoside hydrolases. The enzyme should be useful in biotechnological applications of chitosan hydrolysis, dealing with concentrated chitosan solutions at high temperatures.     

A new linear potentiometric titration method for the determination of deacetylation degree of chitosan

The degree of deacetylation (DD) is one of the most important properties of chitosan. Therefore, a simple, rapid and reliable method for the determination of DD of chitosan is essential. In this report, two new potentiometric titration functions are derived for the determination of DD of chitosan. The effects of the precipitation and the errors induced in pH measurement are discussed in detail. To make this method more simple and reliable, two universal pH regions for the accurate plotting of different DD chitosan samples are proposed for the new potentiometric titration functions. The DD values of three chitosan samples obtained with this new method show good agreement with those yielded from elemental analysis and ¹H-NMR.     

The use of chitosan solutions for defatting and clarification of protein hydrolysates]

The possibility of the use of small amounts of chitosan for defatting and clarification of protein solutions prepared by enzymatic hydrolysis was tested. The following treatment conditions were shown to be optimal: chitosan concentration range, from 1.0 to 1.5 g per kg raw weight; pH of precipitation medium, from 8.0 to 8.5; and duration of incubation of protein hydrolysate solution with chitosan, less than 1 h. The hydrolysate defatting grade was found to depend on the degree of chitosan deacetylation. A possible mechanism of the chitosan-induced effects was suggested. The use of chitosan allows the mass fraction of enzyme protein hydrolysates to be reduced fourfold to fivefold.     

Chemical modification of chitosan. Part 15: synthesis of novel chitosan derivatives by substitution of hydrophilic amine using N-carboxyethylchitosan ethyl ester as an intermediate

The Michael type reaction of chitosan with ethyl acrylate has been investigated. Although this reaction was quite slow in the case of chitosan, the reiteration of the reaction was an effective means for increasing the degree of substitution (DS) of ethyl ester. The N-carboxyethylchitosan ethyl ester as an intermediate was successfully substituted with various hydrophilic amines, although the simultaneous hydrolysis of the ester to carboxylic acid also occurred. Water-soluble chitosan derivatives were obtained by substitution with hydroxyalkylamines and diamines.     

Extraction of starch by dimethyl sulfoxide and quantitation by enzymatic assay

A method for the rapid, sensitive, and specific determination of starch in plant tissues is described. Starch from a variety of plant tissues is solubilized by stirring for 24 h or by sonication for 40 min in dimethyl sulfoxide. Dilution of this extract to less than 20% dimethyl sulfoxide permits a nearly complete hydrolysis of the starch in less than 3 h with glucoamylase from Rhizopus niveus. Quantitation of liberated glucose by a coupled hexokinase and glucose-6-phosphate dehydrogenase method provides an additional degree of specificity.     

Preparation and anticoagulant activity of a low-molecular-weight sulfated chitosan

Synthesis of chitosan sulfates with low molecular weight (M_v 9000–35,000 Da) was carried out by sulfation of low molecular weight chitosan (M_v 10,000–50,000 Da). The oleum was used as sulfating agent and dimethylfornamide as medium. The chitosans were prepared by enzymatic and acidic hydrolysis of initial high molecular weight chitosan as well as by extrusion solid-state deacetylation of chitin. As was shown by FT-IR and NMR-methods and elemental analysis, the sulfation occurred at C-6 and C-3 positions and substitution degree is 1.10–1.63. The molecular weight sulfated chitosan was determined by viscometric method and the Mark–Houwink equation [η]=10⁻⁵ 4.97 M^0.77. Study of anticoagulant activity showed that chitosan sulfates with lowered molecular weight demonstrated a regular increase of anti-Xa activity like heparins.     

Oligosaccharide hydrolysis by chitosanase enzymes monitored by real-time electrospray ionization-mass spectrometry

The chitosanase-catalyzed hydrolysis of chitosan oligosaccharides was investigated for the first time by real-time electrospray ionization-mass spectrometry (ESI-MS). As chitosan oligosaccharides (GlcNn, n=2-6) were hydrolyzed by exochitosanase (exo-beta-glucosaminidase) from Amycolatopsis orientalis, the reaction time-courses of substrate, intermediate and products could be monitored simultaneously by direct infusion of the reaction solvent into the mass spectrometer. Consequently, the analytical approach of real-time MS is an enormous time-saving method. Furthermore, the high sensitivity of the mass spectrometric detection allows the determination of the reaction time-courses with very low quantities of substrate and therefore also a low amount of applied enzyme. Real-time mass spectrometric detection was also applicable in investigating the reaction behaviour of Streptomyces sp. N174 endochitosanase wild type and of two of its mutants. This technique establishes the fast and efficient determination of in vitro enzymatic activities of various enzyme systems.     

Defatting and Clarification of Protein Hydrolysates by Using Chitosan Solutions

The possibility of the use of small amounts of chitosan for defatting and clarification of protein solutions prepared by enzymatic hydrolysis was tested. The following treatment conditions were shown to be optimal: a chitosan concentration range, from 1.0 to 1.5 gram per kilogram raw weight; pH of the precipitation medium from 8.0 to 8.5; and duration of the incubation of the protein hydrolysate solution with chitosan, less than 1 h. The hydrolysate defatting grade was found to depend on the degree of chitosan deacetylation. A possible mechanism of the chitosan-induced effects was suggested. The use of chitosan allows the mass fraction of enzyme protein hydrolysates to be reduced fourfold to fivefold.     

Hydrolysis of Chitosan in Lactic Acid

The effects of molecular weight and the degree of acetylation on the hydrolysis of chitosan in dilute lactic acid were studied. It was demonstrated that the higher the values of both parameters, the more rapid the decreases in viscosity and the viscosity-average molecular weight of chitosan.     

Determination of the degree of N-acetylation (DA) of chitin and chitosan in the presence of water by first derivative ATR FTIR spectroscopy

A new method for the determination of the degree of N-acetylation (DA) of chitin and chitosan is described using first derivative diamond ATR FTIR spectroscopy. Applying the derivative values of the amide III band at 1327 cm⁻¹ and the CH deformation band of the N-acetyl group at 1383 cm⁻¹ as measure of the N-acetyl content of the sample in relation to the derivative value of the bridge oxygen vibration at 1163 cm⁻¹ as internal standard, a linear correlation to the results of first derivative UV spectroscopy was obtained and confirmed by elemental analysis and Raman spectroscopy. The described method allows the determination of the degree of N-acetylation of chitosan and chitin in the presence of water thus making drying procedures unnecessary.     

Hydrolysis of chitosan in lactic acid

Effects of molecular weight and degree of acetylation on the hydrolysis of chitosan in dilute lactic acid were studied. It was demonstrated that the higher were the values of both parameters, the more rapid were the decreases in viscosity and viscosity-average molecular weight of chitosan.     

Effect of the degree of acetylation of chitosan on its enzymatic hydrolysis with the preparation Celloviridin G20x

The degree of acetylation exerted only insignificant effects on the enzymatic hydrolysis of chitosan, while affecting the composition of the resulting hydrolysates and their water solubility. Chitosan with various degrees of acetylation was produced by reacetylation of the original chitosan (the solvents, methanol and 2% acetic acid, were present at a ratio of 54:51 v/v; the amount of acetic anhydride was in the range 0.1-2.0 mmol per 1 g chitosan). Hydrolysis by the enzymatic preparation Celloviridin G20x was performed at the enzyme to substrate ratio of 1:400 in sodium-acetate buffer, pH 5.2 (55 degrees C) for 1 h.     

Effect of the Degree of Acetylation of Chitosan on Its Enzymatic Hydrolysis with the Preparation Celloviridin G20kh

The degree of acetylation was shown to exert only insignificant effects on the enzymatic hydrolysis of chitosan, while affecting the composition of the resulting hydrolysates and their water solubility. Chitosan with various degrees of acetylation was produced by reacetylation of the initial chitosan (the solvents, methanol and 2% acetic acid, were present in a ratio of 54 : 51 v/v; the amount of acetic anhydride was in the range 0.1–2.0 mmol per gram chitosan). Hydrolysis by the enzymatic preparation Celloviridin G20kh was performed at an enzyme-to-substrate ratio of 1 : 400 in sodium–acetate buffer, pH 5.2 (55°C) for 1 h.