Comparison of Extractants for Removing Heavy Metals from Contaminated Clayey Soils

This article describes the removal of heavy metals from contaminated clayey soils by soil washing using various extractants. Two clayey soils, kaolin, a low buffering soil with pH of 5, and glacial till, a high buffering soil with pH of 8, were used to represent various soil conditions. These soils were spiked with chromium (Cr), nickel (Ni), and cadmium (Cd) to simulate improper disposal of typical electroplating waste constituents. The following extracting solutions were investigated for the removal of heavy metals from the soils: deionized water, distilled water, and tap water; acetic acid and phosphoric acid; chelating agents ethylenediaminetetraacetic acid (EDTA) and citric acid; and the oxidizing agents potassium permanganate and hydrogen peroxide. The effect of extractant concentration on removal of heavy metals was also investigated. Complete removal of Cr was achieved using 0.1?M potassium permanganate for kaolin, while a maximum of 54% was removed from glacial till. A maximum Ni removal of 80% was achieved using tapwater for kaolin, while a maximum removal of 48 to 52% was achieved using either 1?M acetic acid or 0.1?M citric acid for glacial till. A maximum Cd removal of 50% was achieved using any of the extractants for kaolin, while a maximum removal of 45 to 48% was obtained using either acids or chelating agents for glacial till. Overall, this study showed that complete removal of Cr, Ni, and Cd from clayey soils is difficult to achieve using the soil-washing process, and also the use of one extractant may not be effective in removing all metals. A sequential extraction using different extractants may be needed for the removal of multiple metal contaminants from clayey soils.     

Solid-Phase Chemical Fractionation of Selected Trace Metals in Some Northern Kentucky Soils

The fractionation and distribution with depth of Cd, Cr, Cu, Ni, Pb, and Zn in 26 soils of Northern Kentucky were determined through a sequential extraction procedure in response to environmental concerns about increasing anthropogenic inputs in a fast-paced, urbanizing area. The selected sites have not received any biosolid- or industrial-waste applications. Average total concentrations per metal in soil profiles derived from alluvial, glacial till, and residual materials ranged from 0.43 to 56.00 mg kg^?1 in the sequence Zn > Ni > Pb > Cr > Cu > Cd, suggesting relatively small anthropogenic inputs. The distribution of Cu, Cr, Ni, and Zn increased with soil depth, whereas Cd and Pb remained stable, indicating a strong geological or pedogenic influence. Residual forms were most important for the retention of Cu, Zn, and Ni. Cadmium and Pb exhibited a strong affinity for the Fe-Mn oxide fraction, while Cr showed the strongest association with the organic fraction. In terms of metal mobility and toxicity potential inferred from metal concentrations in labile fractions, Cd posed the greatest risk, followed by Cr ～ Pb > Ni > Zn > Cu. Soil pH, OM, and clay content were the most important parameters explaining the partitioning of metals in labile and residual fractions, emphasizing the importance of metal fractionation in soil management decisions. Alluvial soils generally contained the highest total and labile metal concentrations, suggesting potential metal enrichment through anthropogenic additions and depositional processes. These environments exhibit the highest risk for metal mobilization due to drastic changes in redox conditions, which can destabilize existing metal retention pools.     

Concentration and Distribution of Six Trace Metals in Northern Kentucky Soils

Concentration and distribution of cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), lead (Pb), and zinc (Zn) were determined in 26 soil profiles (n = 78) of northern Kentucky in response to environmental concerns about increasing anthropogenic inputs in a fast-paced urbanizing area. The selected sites represent alluvial, glacial till or residual soils that have not received any biosolid- or industrial-waste applications. Mean concentrations of Zn (53.8 mg kg^?1) and Ni (25.9 mg kg^?1) were the highest in the soil profile, whereas Cd (0.21 mg kg^?1) was present only in trace amounts. All metals were within the low to middle range of baseline concentrations reported for US soils, suggesting minimal anthropogenic inputs. The distribution of Cu, Cr, Ni, and Zn increased with soil depth, whereas Cd and Pb concentrations were unaffected throughout the soil profile. Alluvial soils had the highest overall metal accumulations, particularly in surface soil horizons, indicating potential metal enrichment through depositional processes. The presence of a fragipan horizon or depth to bedrock did not significantly affect metal retention. Single correlation and multiple regression analyses indicated OM and pH as the most influential soil parameters for metal retention, followed by cation exchange capacity (CEC) and CEC/clay. Single correlations among metals suggested strong covariance of Zn with most metals throughout the soil profile, but weaker for Pb and Ni.     

Adsorption of heavy metal ions from aqueous solutions by activated carbon prepared from apricot stone

Apricot stones were carbonised and activated after treatment with sulphuric acid (1:1) at 200 degrees C for 24 h. The ability of the activated carbon to remove Ni(II), Co(II), Cd(II), Cu(II), Pb(II), Cr(III) and Cr(VI) ions from aqueous solutions by adsorption was investigated. Batch adsorption experiments were conducted to observe the effect of pH (1-6) on the activated carbon. The adsorptions of these metals were found to be dependent on solution pH. Highest adsorption occurred at 1-2 for Cr(VI) and 3-6 for the rest of the metal ions, respectively. Adsorption capacities for the metal ions were obtained in the descending order of Cr(VI) > Cd(II) > Co(II) > Cr(III) > Ni(II) > Cu(II) > Pb(II) for the activated carbon prepared from apricot stone (ASAC).     

Heavy metal contamination in water,soil, and milk of the industrial area adjacent to Swan River,Islamabad, Pakistan

Trace heavy metals such as Cr(III), Ni(II), Cd(II), Zn(II), Pb(II), and Cu(II) are hazardous pollutants and are rich in areas with high anthropogenic activities. Their concentrations were analyzed using atomic absorption spectroscopy, and it was found that their concentrations were several fold higher in downstream Swan River water samples of the Kahuta Industrial Triangle as compared to upstream. Heavy metal soil concentrations taken from the downstream site were 149% for Cr, 131% for Ni, 176% for Cd, 139% for Zn, 224% for Pb, and 182% for Cu when compared to samples from the upstream site. Quantitative analysis concluded that these metals were higher in milk samples collected from downstream as compared to the samples from upstream water-irrigated sites. The order of metal in milk was as Zn > Cr > Cu > Cd > Pb = Ni. Heavy metal contaminations may affect the drinking water quality, food chain, and ecological environment. It was also suggested that the toxicity due to such polluted water, soil, and milk are seriously dangerous to human health in future.     

Solution and solid-state studies of complexation of transition-metal cations and Al(III) by aroylhydrazones derived from nicotinic acid hydrazide

Reactions of first series transition-metal cations, Cd(II) and Al(III) with two aroylhydrazones derived from nicotinic acid hydrazide and salicylaldehyde or o-vanillin were studied at 25 °C in buffered dioxane/water 1/1 mixture (pH 5.8) by means of spectrophotometric and spectrofluorimetric titrations. The addition of Mn(II) or Cd(II) ions in hydrazone solutions had no effect on their absorption spectra whereas the addition of Ni(II) and Cr(III) immediately caused precipitation. The reaction of Zn(II) with salicylaldehyde derivative was found to be photosensitive. Relatively high conditional stability constants of 1:1 complexes of Cu(II), Zn(II) and Al(III) with both ligands were determined. Solid complexes of Cu(II), Ni(II) and Zn(II) with aroylhydrazones studied were isolated and characterized by elemental and thermogravimetric analyses, magnetic susceptibility measurements (in the case of Cu(II) and Ni(II)) and IR spectrometry.     

Comparison of the toxicity of heavy metals to cabbage growth

Summary Cabbage plants were grown for 55 days with a nutrient solution containing 1 and 10 ppm of V, Cr(III), Cr(VI), Mn, Fe, Co, Ni, Cu, Zn, Cd, Hg(I), orHg(II). A comparison of the plant growth and chemical analysis revealed that Cr(VI), Cu, Cd, and Hg(II) in the solution are most toxic to the plant growth (hence detrimental to the cabbage-head formation) and Mn, Fe, and Zn are less toxic than other heavy metals, and that Mn, Zn, Co, Ni, and Cd and translocated into all the plant organs while V, Cr(III), Cr(VI), Fe, Cu, Hg(I), and Hg(II) are accumulated in the roots.     

Online column preconcentration for speciation and selective determination of Cr(III) in natural water samples using flow injection with chemiluminescence detection

A simple, rapid, sensitive and inexpensive approach is described in this work based on a combination of solid-phase extraction of 8-hydroxyquinoline (8HQ), for speciation and preconcentration of Cr(III) and Cr(VI) in river water, and the direct determination of these species using a flow injection system with chemiluminescence detection (FI–CL) and a 4-diethylamino phenyl hydrazine (DEAPH)–hydrogen peroxide system. At different pH, the two forms of chromium [Cr(III) and Cr(VI)] have different exchange capacities for 8HQ, therefore two columns were constructed; the pH of column 1 was adjusted to pH 3 for retaining Cr(III) and column 2 was adjusted to pH 1 for retaining of Cr(VI). The sorbed Cr(III) and Cr(VI) species were eluted from columns using 3.0 ml of 0.1 N of HCl and 3.0 ml of 0.1 N of NaOH, respectively. The flow injection–chemiluminescence (FI–CL) method is based on light emitted due to the oxidation of DEAPH by the H₂O₂ in the presence of Cr(III), which catalyzes the reaction. The flow cell is a transparent coiled tube made from glass (2.0 × 4.0, inner and outer diameter) and located close to the photodetector. The flow parameters: flow rate, sample volume, flow cell length, and distance to the CL detector were studied and optimized. Under optimum flow conditions, the Cr(III) concentration can be determined over the range 5–350 μg L⁻¹ with a limit of detection of 1.2 μg L⁻¹, as the Cr(III) concentration is proportional to the intensity of the CL signal. The relative standard deviations (%) for 10 and 50 μg L⁻¹ Cr(III) were 1.2% and 3.2%, respectively. The effects of Al(III), Cd(II), Zn(II), Hg(II), Pb(II), Co(II), Cu(II), Ni(II), Mn(II), Ca(II), and Fe(III) were investigated. The proposed method is highly selective and sensitive, enabling a rapid determination of the Cr(III) amount in the presence of other interfering metals. Finally, the FI–CL method was examined in five river water samples with excellent recoveries.     

Ternary biosorption studies of Cd(II), Cr(III) and Ni(II) on shelled Moringa oleifera seeds

Competitive biosorption of Cd(II), Cr(III) and Ni(II) on unmodified shelled Moringa oleifera seeds (SMOS) present in ternary mixture were compared with the single metal solution. The extent of adsorption capacity of the ternary metal ions tested on unmodified SMOS was low (10-20%) as compared to single metal ions. SMOS removed the target metal ions in the selectivity order of Cd(II) > Cr(III) > Ni(II). Sorption equilibria, calculated from adsorption data, explained favorable performance of biosorption system. Regeneration of exhausted biomass was also attempted for several cycles with a view to restore the sorbent to its original state.     

Fluxes and budgets of Cd, Zn, Cu, Cr and Ni in a remote forested catchment in Germany

The input of heavy metals by atmospheric deposition to forested watersheds substantially decreased during the last decades in many areas. The goal of our study was to identify the present sinks and sources of metals and factors influencing metal mobility at the catchment and soil profile scale. We determined concentrations and fluxes of Cd, Zn, Cu, Cr and Ni in precipitation, litterfall, soil solutions (Oi, Oe, Oa horizon percolates, 20 and 90?cm soil depth) and runoff in a forest ecosystem in NE-Bavaria, Germany for 1?year. The metal concentrations in solutions were mostly <10???g?l^?1 beside Zn (<1200???g?l^?1). The present total deposition was estimated at 1.0, 560, 30, 1.2 and 10.4?g?ha^?1?year^?1 for Cd, Zn, Cu, Cr and Ni, respectively. The mass balance (total deposition minus runoff) at the catchment scale indicated actual retention of Zn, Cu and Ni, but an almost balanced budget for Cr and Cd. Considering the soil profile scale, the Oi horizon still acted as a sink, whereas the Oe and Oa horizons were presently sources for all metals. The solid?Csolution partitioning coefficients indicated higher mobility of Cd and Zn than of Cu, Cr and Ni in forest soils. In the mineral soil horizons, K_d values derived from field measurements were substantially larger than those predicted with empirical regression equations from Sauv?? et al. (Environ Sci Technol 34:1125?C1131, 2000; Environ Sci Technol 37:5191?C5196, 2003). The mineral soil acted as a sink for all metals beside Cd. Dissolved organic C and pH influenced the metal mobility, as indicated by significant correlations to metal concentrations in Oa percolates and runoff. The solid?Csolution partitioning coefficients indicated higher mobility of Cd and Zn than of Cu, Cr and Ni in forest soils. Overall, the decreased deposition rates have obviously induced a source function of the Oe and Oa horizon for metals. Consequently, mobilization of metals from forest floor during heavy rain events and near surface flow conditions may lead to elevated concentrations in runoff.     

Adsorption studies on rice husk: removal and recovery of Cd(II) from wastewater

Adsorption behaviour of Ni(II), Zn(II), Cd(II) and Cr(VI) on untreated and phosphate-treated rice husk (PRH) showed that adsorption of Ni(II) and Cd(II) was greater when PRH was used as an adsorbent. Sorption of Cd(II) was dependent on contact time, concentration, temperature, adsorbent doses and pH of the solution. The Langmuir constants and thermodynamic parameters have been calculated at different temperatures. It was found that recovery of Cd(II) from synthetic wastewater by column operation was better than a batch process.     

Use of silica-immobilized humin for heavy metal removal from aqueous solution under flow conditions

Humin extracted from Sphagnum peat moss was immobilized in a silica matrix and column experiments were performed in order to evaluate the removal and recovery of metal ions from aqueous solution under flow conditions. These experiments also allowed testing the recycling capacity of the column. Single-element solutions of Cu(II) and Pb(II), and a multi-metal solution containing Cd(II), Cu(II), Pb(II), Ni(II), and Cr(III) were passed through the columns at a flow rate of 2 ml/min. A 0.5 M sodium citrate solution was used as the stripping agent in the metal-ion recovery process. Humin immobilized in the silica matrix exhibited a similar, and in some cases, even a higher capacity than other biosorbents for the removal of metal ions from aqueous solutions under flow conditions. The sodium citrate was effective in removing Cu(II), Pb(II), Cd(II), and Ni(II) from the metal saturated column. The selectivity of the immobilized biomass was as follows: Cr(III)>Pb(II)>Cu(II)>Cd(II)>Ni(II). This investigation provides a new, environmentally friendly and cost-effective possibility to clean up heavy-metal contaminated wastewaters by using the new silica-immobilized humin material.     

Elimination of Heavy Metals from Leachates by Membrane Electrolysis

The elimination of heavy metals from bioleaching process waters (leachates) by electrolysis was studied in the anode and cathode region of a membrane electrolysis cell at current densities of 5–20 mA/cm² using various electrode materials. The leaching waters containing a wide range of dissolved heavy metals, were high in sulfate, and had pH values of approx. 3. In preliminary tests using a rotating disc electrode the current density‐potential curve (CPK) was recorded at a rotation velocity of 0, 1000 and 2000 rpm and a scan rate of 10 mV/s in order to collect information on the influence of transport processes on the electrochemical processes taking place at the electrodes. The electrochemical deposition‐dissolution processes at the cathode are strongly dependent on the hydrodynamics. Detailed examination of the anodic oxidation of dissolved Mn(II) indicated that the manganese dioxide which formed adhered well to the electrode surface but in the cathodic return run it was again reduced. Electrode pairs of high‐grade steel, lead and coal as well as material combinations were used to investigate heavy metal elimination in a membrane electrolysis cell. Using high‐grade steel, lead and carbon electrode pairs, the reduction and deposition of Cu, Zn, Cr, Ni and some Cd in metallic or hydroxide form were observed in an order of 10–40 % in the cathode chamber. The dominant process in the anode chamber was the precipitation of manganese dioxide owing to the oxidation of dissolved Mn(II). Large amounts of heavy metals were co‐precipitated by adsorption onto the insoluble MnO₂. High‐grade steel and to some extent lead anodes were dissolved and hence were proven unsuitable as an anode material. These findings were largely confirmed by experiments using combination electrodes of coal and platinized titanium as an anode material and steel as a cathode material. With both electrode combinations and current densities of 5 or 10 mA/cm², in the cathode region low depositions of 10–20 % Cd, 2–10% Mn, 5–20 % Zn, 1–20 % Co and 5–15 % Ni were measured. By contrast, the elimination of other metals was substantially larger: Fe 40 –60 %, Cu 20–40 %, and Cr 40–60 %. In the anode region the removal of heavy metals was in the order of 30–50%, with Mn being as high as 80 %. The anode materials exhibit good resistance at the current densities tested. The precipitates deposited in both electrode regions contained as main components Al with 10–20 %, Mg with approximately 10 %, and SO₄ with 5–20 %. The solid material in the cathode chamber consisted of relatively high proportions of Zn and Mn. Calcium in the solids indicated the co‐precipitation of calcium sulfate. The main components in the solids of the anode chamber were Mn in the form of pyrolusite, Al as basic sulfate, and Mg. The results indicate that electrochemical metal separation in the membrane electrolysis cell can represent a practical alternative to the metal separation by alkalization. Regarding the main heavy metals Zn, Mn and Ni in the process water, combination electrodes using steel as a cathode material and coal or platinized titanium as an anode material proved to be suitable for eliminating the heavy metals from the aqueous phase. However, for practical application, further work is necessary to improve the efficiency, applicability and costs of the process.     

Heavy Metal Contamination in Roadside Soil and Their Mobility in Relations to pH and Organic Carbon

Concentrations of Pb, Zn, Cd, Ni, Cu, Cr, and Mn were determined to assess the impact of automobiles on heavy metal contamination of roadside soil. Soil samples at four polluted sites and a control site were collected at a depth of 0, 2, 5, 10, 15, 20, 30?cm. A comparison of elemental levels between polluted and control sites exhibited exceptionally higher concentrations at the former sites. The Pb levels in polluted sites varied from 70 to 280.5?µgg^?1and it rapidly decreased with depth. Similarly, mean concentrations of Zn, Cd, Ni, Cu, Cr, and Mn were significantly higher at polluted sites and followed a decreasing trend with the increase in depth. Correlation coefficients between heavy metals and traffic density were positively significant except for nickel. Profile samples showed that Pb, Zn, Cd, Cu, and Mn were largely concentrated in the top 5?cm confirming airborne contamination. The vertical movement and partitioning of metals, except Ni and Cr, exhibited predominant association with soil pH and organic carbon. The results have been presented using Heavy Metal Index.     

Heavy metal contamination and health risk assessment in soil-rice system near Xinqiao mine in Tongling city,Anhui province,China

In this study, paddy soil and rice grain samples were collected from the vicinity around the Xinqiao mine in Tongling, China to test for the presence of heavy metals (Cd, Ni, Cr, Cu, Zn, and Pb) in soil-rice system. Results indicated that the soil samples were primarily contaminated with Cd and Cu and followed with Zn and Pb. In rice grains, Cd, Cu, and Cr concentrations exceeded recommended guidelines. However, the regional distribution of heavy metals in rice grains and soil was inconsistent. The bioaccumulation factor of heavy metals in rice grains decreased in the order of Cd > Zn > Cu > Ni > Cr > Pb. The BAF was significantly positively correlated with TCLP-extractable metals and significantly negatively correlated with soil pH. However, the relationship between soil organic matter and the BAF in rice grains was complex. Health risk assessment through rice intake showed that hazard quotients of Cu and Cd were greater than 1 and could pose a considerable non-cancer health risk to adults and children; meanwhile, Cr, Ni, and Cd could pose an unacceptable cancer risk. The results indicated that the government must take measures to reduce heavy metal contents in paddy soil and rice.     

成都平原北部水稻土重金属含量状况及其潜在生态风险评价

为了解成都平原水稻土重金属含量状况和潜在的生态风险,选取成都平原北部水稻土典型区域为研究对象,采集了158个表层土壤样品,分析了土壤中pH值和Cd、Cu、As、Hg、Pb、Cr、Ni 7种重金属元素含量,以20世纪80年代测定的成都平原土壤重金属元素背景值为评价标准,采用Hakanson潜在生态危害指数法对研究区域的重金属潜在生态风险进行了评价。结果表明:研究区域水稻土Cd、Hg、Ni、Cu、Pb、Cr和As平均含量分别为0.709、0.187、32.08、34.12、31.52、82.13 mg/kg和7.25 mg/kg;Cd、Ni、Cu和Hg 4种重金属超过《土壤环境质量标准》(GB15618-1995) Ⅱ级标准值样本比例分别为87.34%、8.23%、3.80%和3.80%,Cd含量超标严重。7种重金属元素变异系数幅度为18.35%-49.03%,由大到小依次为Cd、Hg、Cu、As、Ni、Cr、Pb。75.32%的样本达到中度或较强重金属潜在生态风险,区域整体表现为中度潜在生态风险(RI平均值为198.65),Cd和Hg为高生态风险元素,对潜在生态风险贡献率分别为62.27%和20.78%,As、Pb、Cu、Ni、Cr为低生态风险元素;风险概率图显示城区周边和绵远河沿线的潜在生态风险等级较高。因此,成都平原水稻土农业生产中应采取一定的措施防控农产品Cd和Hg污染。     

Chromium(III) Oxidation Coupled with Microbially Mediated Mn(II) Oxidation

Abstract

Reductive immobilization of Cr(VI) has been widely explored as a cost-effective approach for Cr-contaminated site remediation. In soils containing manganese oxides, however, the immobilized form of chromium, i.e., Cr(III), could potentially be reoxidized. In this study, batch experiments were conducted to assess whether there were any microbial processes that could accelerate Cr(III) oxidation in aerobic, manganese-containing systems. The results showed that in the presence of at least one species of manganese oxidizers, Pseudomonas putida, Cr(III) oxidation took place at low concentrations of Cr(III). About 30–50% of added Cr(III) (10–200 μ M) was oxidized to Cr(VI) within five days in the systems with P. putida and biogenic Mn oxides. The rate of Cr(III) oxidation was approximately proportional to the initial concentration of Cr(III) up to 100 μ M, but the growth of P. putida was partially inhibited by Cr(III) at 200 μ M and totally stopped when it reached 500 μ M. Cr(III) oxidation was dependent upon the biogenic formation of Mn oxides, though the oxidation rate was not directly proportional to the amount of Mn oxides formed. Chromium(III) oxidation took place through a catalytic pathway, in which the microbes mediated Mn(II) oxidation to form Mn-oxides, and Cr(III) was subsequently oxidized by the biogenic Mn-oxides.     

Chemical speciation distribution characteristics and ecological risk assessment of heavy metals in soil from Sunan mining area,Anhui Province,China

In this study, the content characteristics, comprehensive pollution assessment, and morphological distribution characteristics of heavy metals (Mn, Cd, Cr, Pb, Ni, Zn, and Cu) were researched based on the processes of field investigation, sample collection, and experimental analysis. Results showed that the mean concentrations of Mn, Pb, Cr, Cu, Cd, Zn, and Ni in surface soils were 522.77, 22.56, 55.10, 25.41, 0.25, 57.02, and 48.47 mg kg^?1, respectively. The surface soil from Sunan mining area was contaminated by Cu, Cd, and Ni in different degrees, and high CV values of Cd, Zn, Pb, and Ni were influenced by local human activities possibly. The evaluation results suggested that the mean I_geo values were in the sequence of Cd (0.657) > Ni (0.052) > Cu (?0.293) > Mn (?0.626) > Zn (?0.761) > Cr (?0.884) > Pb (?0.899). Besides, Cd was the most significant potential risk factor among all elements. Nevertheless, the Cd of bioavailable speciations with higher proportion had stronger migration and toxicity, and was more easier to be absorbed and enriched than other elements by some crops (e.g., vegetables, rice), and being at a relatively higher potential ecological risk in soil.     

Spontaneous Cr(VI) and Cd(II) biosorption potential of native pinnae tissue of Pteris vittata L., a tropical invasive pteridophyte

Heavy metal pollution is a prevalent and critical environmental concern. Its rampancy is attributed to indiscriminate anthropogenic activities. Several technologies including biosorption have been continuously researched upon to overcome the limitations of the conventional method of treatments in removal of heavy metals. Biosorption technology involves the application of a biomass in its nonliving form. Pteris vittata L., a pteridophyte, considered as an invasive weed was investigated in the present study as a potential decontaminant of toxic metals, Cr(VI) and Cd(II). The adsorption capacity of the biosorbent for Cr(VI) and Cd(II) under equilibrium conditions was investigated. The morphology, elemental composition, functional groups, and thermal stability of the biosorbent before and after metal loading were evaluated. At 303?K and an equilibrium time of 120?min, the maximum loading of Cr(VI) on the biosorbent was estimated to be 166.7?mg/g at pH 2 and Cd(II) to be 31.3?mg/g at pH 6. Isotherm models, kinetic studies, and thermodynamic studies indicated the mechanisms, chemisorption, ion exchange and intraparticle diffusion, controlling the Cr(VI) and Cd(II) uptake, respectively. The interactive effect of multi-metal ions in binary component systems was synergistic for Cd(II) uptake. The results validate the toxic metal removal potency of the biosorbent.     

The Remediation of Chromium (VI)-Contaminated Soils Using Microbial Fuel Cells

Chromium (VI) is a priority pollutant in soil and water and poses serious threats to the environment. Microbial fuel cells (MFCs), as a sustainable technology, have been applied to treat heavy-metal-contaminated wastewater. To study MFC application in soil remediation, red clay soil and fluvo-aquic soil were spiked with Cr(VI) and packed into a cathode chamber of MFCs, which were then operated at external resistances of 100 and 1000 Ω for 16 days, with open circuit condition as a control treatment. After the operation, the concentration of dissolved Cr(VI) in supernatant and total Cr(VI) in soil was decreased. Soil type and external resistance significantly affected the current, removal efficiency of Cr(VI), and cathode efficiency. Reducing external resistance improved the removal efficiency. The red soil generated a higher current of MFCs, but showed a lower removal efficiency and cathode efficiency than fluvo-aquic soil, implying that the red soil may contain more electron acceptors that competed with Cr(VI) reduction reaction. Our study demonstrated that MFC-based technology has the potential to remediate Cr(VI)-contaminated soil; the efficiency varied between soil types and can be improved with high current.