Multi-metal biosorption and bioaccumulation by Exiguobacterium sp. ZM-2

The present work deals with the biosorption performance of dried and non-growing biomasses of Exiguobacterium sp. ZM-2, isolated from soil contaminated with tannery effluents, for the removal of Cd²⁺, Ni²⁺, Cu²⁺, and Zn²⁺ from aqueous solution. The metal concentrations studied were 25 mg/l, 50 mg/l, 100 mg/l, 150 mg/l and 200 mg/l. The effect of solution pH and contact time was also studied. The biosorption capacity was significantly altered by pH of the solution. The removal of metal ions was conspicuously rapid; most of the total sorption occurred within 30 min. The sorption data have been analyzed and fitted to the Langmuir and Freundlich isotherm models. The highest Q_max value was found for the biosorption of Cd²⁺ at 43.5 mg/g in the presence of the non-growing biomass. Recovery of metals (Cd²⁺, Zn²⁺, Cu²⁺ and Ni²⁺) was found to be better when dried biomass was used in comparison to non-growing biomass. Metal removal through bioaccumulation was determined by growing the bacterial strain in nutrient broth amended with different concentrations of metal ions. This multi-metal resistant isolate could be employed for the removal of heavy metals from spent industrial effluents before discharging them into the environment.     

Zn2+ biosorption by Oscillatoria anguistissima

Oscillatoria anguistissima showed a very high capacity for Zn²⁺ biosorption (641 mg g⁻¹ dry biomass at a residual concentration of 129·2 ppm) from solution and was comparable to the commmercial ion-exchange resin IRA-400C. Zn²⁺ biosorption was rapid, pH dependent and temperature independent phenomenon. Zn²⁺ adsorption followed both Langmuir and Freundlich models. The specific uptake (mg g⁻¹ dry biomass) of metal decreased with increase in biomass concentration. Pretreatment of biomass did not significantly affect the biosorption capacity of O. anguistissima. The biosorption of zinc by O. anguistissima was an ion-exchange phenomenon as a large concentration of magnesium ions were released during zinc adsorption. The zinc bound to the biomass could be effectively stripped using EDTA (10 mM) and the biomass was effectively used for multiple sorption–desorption cycles with in-between charging of the biomass with tap water washings. The native biomass could also efficiently remove zinc from effluents obtained from Indian mining industries.     

Immobilization of <Emphasis Type="Italic">Pseudomonas putida</Emphasis> PT in resistant matrices to environmental stresses: a strategy for continuous removal of heavy metals under extreme conditions

The purpose of this study was to investigate the potential of immobilized lead- and cadmium-resistant Pseudomonas putida strain PT to remove heavy metals from aqueous medium under extreme conditions. The tolerance and accumulation of cadmium and lead ions by strain PT were investigated by minimal inhibitory concentration (MIC) determination and polymerase chain reaction (PCR) of cadA gene, respectively. The surface chemical functional groups of P. putida PT involved in the metal biosorption were identified by Fourier transform infrared (FTIR). Pseudomonas putida PT was immobilized in three matrices include carboxy-methyl cellulose (CMC), rice bran, and a new composite made of alginate, polyvinyl alcohol (PVA), and CaCO₃ to prepare heavy metal adsorbent. The biosorbents were analyzed by SEM, and their metal removal capability was assayed in two consecutive cycles by atomic absorption spectroscopy. The viability of immobilized bacterial cells was determined by flow cytometry during storage at 4 °C and exposure to the environmental stresses (pH and temperature). The results showed that PT strain was resistant up to 10 mM Pb²⁺ and 8 mM Cd²⁺. FTIR analysis revealed that alcohol, sulfur, phosphate, esters, and amide groups played important roles in metal biosorption process and, also change in metabolic reactions like hydration and polyesters accumulation was observed after metal biosorption. The presence of cadA gene, a heavy metal translocating pump-coding gene, indicated the ability of metals bioaccumulation by the PT strain. Immobilized cells in alginate–PVA–CaCO₃ and rice bran showed the highest metal removal efficiency for Pb²⁺ as 75% and Cd²⁺ as 96.7%, respectively. Metal adsorbents were reusable, and the highest removal efficiency in the second cycle was observed in inoculated alginate–PVA–CaCO₃ (79.5% Pb²⁺ and 45% Cd²⁺). Flow cytometric analysis represented that the immobilized cell viability was retained (<?97%) after 4 weeks storage at 4 °C. Viability under two environmental stresses in all matrices was as follows: <?96% at 25 °C, <?87% at 45 °C, <?85% at pH 4,?<?96% at pH 7, and?<?89% at pH 11. The results signify that these metal adsorbents are efficient technological tools for bioremediation even in harsh environmental conditions.     

Lead sorption by living biomass of Chroococcus multicoloratus and Oscillatoria trichoides: kinetics and equilibrium studies

We report here the ability of two freshwater living cyanobacteria, Chroococcus multicoloratus Wood and Oscillatoria trichoides Szafer, to remove lead (Pb²⁺) from aqueous solutions in batch system, wherein the effect of Pb²⁺ on the growth rate of both the cyanobacteria was evaluated. The influence of sorption time, initial pH, initial Pb²⁺ ion concentration, culture density and the biosorption equilibrium kinetics was examined. Biosorption capacity was found to be maximum between a pH of 5 and 5.14, on the second day of exposure and at an initial concentration of 80 and 60 mg L^?1 for C. multicoloratus and O. trichoides, respectively. An initial concentration in the range of 10–120 mg L^?1 significantly decreased the growth and efficiency of Pb²⁺ removal. The maximum sorptive capacity (q _max) obtained from the Langmuir isotherm for C. multicoloratus and O. trichoides was 178.57 and 106.38 mg g^?1, respectively. The pseudo-second-order model was found to correlate well with the experimental data. Metal recovery of 70–77 % was obtained with HCl as a desorbing agent. The results of Fourier transform infrared spectroscopy indicated the participation of hydroxyl, carboxyl and amino groups in the biosorption process. Based on our observations, we suggest that both species appear to be potential viable biosorbents for mildly acidic water contaminated with Pb²⁺.     

Comparison of Rhizopus nigricans in a pelleted growth form with some other types of waste microbial biomass as biosorbents for metal ions

Biosorption of metal ions (Li⁺, Ag⁺, Pb²⁺, Cd²⁺, Ni²⁺, Zn²⁺, Cu²⁺, Sr²⁺, Fe²⁺, Fe³⁺ and Al³⁺) by Rhizopus nigricans biomass was studied. It was shown that metal uptake is a rapid and pH-dependent process, which ameliorates with increasing initial pH and metal concentrations. Different adsorption models: Langmuir, Freundlich, split-Langmuir and combined nonspecific-Langmuir adsorption isotherm were applied to correlate the equilibrium data. The maximum biosorption capacities for the individual metal ions were in the range from 160 to 460 mol/g dry weight. Scatchard transformation of equilibrium data revealed diverse natures of biomass metal-binding sites. The binding of metals was also discussed in terms of the hard and soft acids and bases principle. The maximum biosorption capacities and the binding constant of R. nigricans were positively correlated with the covalent index of metal ions.The following types of waste microbial biomass originating as by-products from industrial bioprocesses were tested for biosorption of metal ions: Aspergillus terreus, Saccharomyces cerevisiae, Phanerochaete chrysosporium, Micromonospora purpurea, M. inyoensis and Streptomyces clavuligerus. The determined maximum biosorption capacities were in the range from 100 to 500 mol/g dry weight. The biosorption equilibrium was also represented with Langmuir and Freundlich sorption isotherms.     

Equilibrium and Kinetic Studies of Cd2+ Biosorption by the Brown Algae Sargassum fusiforme

A fundamental investigation of the biosorption of Cd²⁺ from aqueous solution by the edible seaweed Sargassum fusiforme was performed under batch conditions. The influences of experimental parameters, such as the initial pH, sorption time, temperature, and initial Cd²⁺ concentration, on Cd²⁺ uptake by S. fusiforme were evaluated. The results indicated that the biosorption of Cd²⁺ depended on the initial Cd²⁺ concentration, as well as the pH. The uptake of Cd²⁺ could be described by the Langmuir isotherm model, and both the Langmuir biosorption equilibrium constant and the maximum biosorption capacity of the monolayer decreased with increasing temperature, thereby confirming the exothermic character of the sorption process. The biosorption kinetics follows the pseudo-second-order kinetic model, and intraparticle diffusion is the sole rate-limiting step for the entire biosorption period. These fundamental equilibrium and kinetic results can support further studies to the removal of cadmium from S. fusiforme harvested from cadmium-polluted waters.     

Al<Superscript>3+</Superscript> and Fe<Superscript>2+</Superscript> toxicity reduction potential by acid-resistant strains of <Emphasis Type="Italic">Rhodopseudomonas palustris</Emphasis> isolated from acid sulfate soils under acidic conditions

This research aimed to evaluate the capacity of acid-resistant purple nonsulfur bacteria, Rhodopseudomonas palustris strains VNW02, TLS06, VNW64, and VNS89, to resist Al³⁺ and Fe²⁺ and to investigate their potential to remove both metals from aqueous solutions using exopolymeric substances (EPS) and biomasses. Based on median inhibition concentration (IC₅₀), strain VNW64 was the most resistant to both metals under conditions of aerobic dark and microaerobic light; however, strain TLS06 was more resistant to Al³⁺ under aerobic dark conditions. High metal concentrations resulted in an altered cellular morphology, particularly for strain TLS06. Metal accumulation in all tested PNSB under both incubating conditions as individual Al³⁺ or Fe²⁺ was in the order of cell wall?>?cytoplasm?>?cell membrane. This was also found in a mixed metal set only under conditions of aerobic dark as microaerobic light was in the degree of cytoplasm?>?cell wall?>?cell membrane. Of all strains tested, EPS from strain VNW64 had the lowest carbohydrate and the highest protein contents. Metal biosorption under both incubating conditions, EPS produced by strains VNW64 and TLS06, achieved greater removal (80 mg Al³⁺ L^?1 and/or 300 mg Fe²⁺ L^?1) than their biomasses. Additionally, strain VNW64 had a higher removal efficiency compared to strain TLS06. Based on the alteration in cellular morphology, including biosorption and bioaccumulation mechanisms, R. palustris strains VNW64 and TLS06 demonstrated their resistance to metal toxicity. Hence, they may have great potential for ameliorating the toxicity of Al³⁺ and Fe²⁺ in acid sulfate soils for rice cultivation.     

Heterologous Expression and Metal-Binding Characterization of a Type 1 Metallothionein Isoform (OsMTI-1b) from Rice (Oryza sativa)

Metallothioneins (MTs) are ubiquitous, low molecular mass and cysteine-rich proteins that play important roles in maintaining intracellular metal homeostasis, eliminating metal toxification and protecting the cells against oxidative damages. MTs are able to bind metal ions through the thiol groups of their cysteine residues. Plants have several MT isoforms which are classified into four types based on the arrangement of cysteine residues. In the present study, a rice (Oryza sativa) gene encoding type 1 MT isoform, OsMTI-1b, was inserted in vector pET41a and overexpressed in Escherichia coli as carboxy-terminal extensions of glutathione-S-transferase (GST). The recombinant protein GST-OsMTI-1b was purified using affinity chromatography and its ability to bind with Ni²⁺, Cd²⁺, Zn²⁺ and Cu²⁺ ions was analyzed. The results demonstrated that this isoform has ability to bind Ni²⁺, Cd²⁺ and Zn²⁺ ions in vitro, whereas it has no substantial ability to bind Cu²⁺ ions. From competitive reaction with 5,5′-dithiobis(2-nitrobenzoic acid), DTNB, the affinity of metal ions for recombinant form of GST-OsMTI-1b was as follows: Ni²⁺/Cd²⁺ > Zn²⁺ > Cu²⁺     

Biosorption of Pb<Superscript>2+</Superscript> and Zn<Superscript>2+</Superscript> by Non-Living Biomass of <Emphasis Type="Italic">Spirulina</Emphasis> sp.

Removal of heavy metals (Pb²⁺, Zn²⁺) from aqueous solution by dried biomass of Spirulina sp. was investigated. Spirulina rapidly adsorbed appreciable amount of lead and zinc from the aqueous solutions within 15 min of initial contact with the metal solution and exhibited high sequestration of lead and zinc at low equilibrium concentrations. The specific adsorption of both Pb²⁺ and Zn²⁺ increased at low concentration and decreased when biomass concentration exceeded 0.1 g l⁻¹. The binding of lead followed Freundlich model of kinetics where as zinc supported Langmuir isotherm for adsorption with their r ² values of 0.9659 and 0.8723 respectively. The adsorption was strongly pH dependent as the maximum lead biosorption occurred at pH 4 and 10 whereas Zn²⁺ adsorption was at pH 8 and 10.     

Influence of metal ions on bioremediation activity of protocatechuate 3,4-dioxygenase from Stenotrophomonas maltophilia KB2

The aim of this paper was to describe the effect of various metal ions on the activity of protocatechuate 3,4-dioxygenase from Stenotrophomonas maltophilia KB2. We also compared activity of different dioxygenases isolated from this strain, in the presence of metal ions, after induction by various aromatic compounds. S. maltophilia KB2 degraded 13 mM 3,4-dihydroxybenzoate, 10 mM benzoic acid and 12 mM phenol within 24 h of incubation. In the presence of dihydroxybenzoate and benzoate, the activity of protocatechuate 3,4-dioxygenase and catechol 1,2-dioxygenase was observed. Although Fe³⁺, Cu²⁺, Zn²⁺, Co²⁺, Al³⁺, Cd²⁺, Ni²⁺ and Mn²⁺ ions caused 20–80 % inhibition of protocatechuate 3,4-dioxygenase activity, the above-mentioned metal ions (with the exception of Ni²⁺) inhibited catechol 1,2-dioxygenase to a lesser extent or even activate the enzyme. Retaining activity of at least one of three dioxygenases from strain KB2 in the presence of metal ions makes it an ideal bacterium for bioremediation of contaminated areas.     

两种大型真菌子实体对Cd2+的生物吸附特性

对两种多孔菌科大型真菌槐栓菌(Trametes robiniophila)和木蹄层孔菌(Fomes fomentarius)子实体生物吸附Cd²⁺的影响因素(包括吸附剂用量、初始pH、吸附时间、初始Cd²⁺浓度)和吸附特性进行分析。结果表明,槐栓菌和木蹄层孔菌对低浓度的Cd²⁺(10 mg/L)吸附的最适pH为6;Cd²⁺的去除率随吸附剂用量和吸附时间的增加而增大,槐栓菌和木蹄层孔菌均在吸附剂用量为2g/L时达到吸附平衡,槐栓菌在吸附时间为30 min时达到吸附平衡,而木蹄层孔菌在吸附时间为60 min时达到吸附平衡;槐栓菌和木蹄层孔菌对10 mg/L Cd²⁺的最大去除率分别为98%和94%。Langmuir等温吸附平衡模型比Freundlich等温吸附平衡模型能更好的拟合两种大型真菌对Cd²⁺的吸附过程;槐栓菌和木蹄层孔菌对10 mg/L Cd²⁺的最大吸附量分别为17.40 mg/g和8.91 mg/g。对实验数据进行动力学模型拟合可知,两种大型真菌对Cd²⁺的生物吸附过程均符合准二阶动力学模型。槐栓菌和木蹄层孔菌生物吸附低浓度Cd²⁺的化学反应机理可能为离子交换。     

沉水植物菹草在低温条件下对重金属Cu、Pb、Zn的吸附和富集

在10℃的较低温度条件下,研究了冬春季节生长旺盛的沉水植物菹草(Potamogeton crispus L.)对重金属离子Cu²⁺,Pb²⁺,Zn²⁺的生物吸附特征及解吸情况,对不同初始浓度重金属水体中的重金属离子去除率情况,以及在此过程中菹草各器官(叶、茎、根茎、根)对重金属离子的富集情况。结果表明,菹草对Cu²⁺,Zn²⁺的吸附在20 min内达到平衡,对Pb²⁺的吸附在50 min内达到平衡,吸附动力学结果符合伪二级动力学方程,决定系数分别达1,1,0.997 8。Freundlich等温线可较好地拟合菹草吸附Cu²⁺,Pb²⁺,Zn²⁺的过程,Cu²⁺,Pb²⁺,Zn²⁺的吸附容量分别达到66.900 6,26.543 0,30.371 8 mg·L^-1。以去离子水作洗脱剂,解吸液中3种重金属离子浓度均低于仪器检出限(0.01 mg·L^-1),解吸程度微弱。投放菹草后,随着初始处理浓度的升高,水体Cu²⁺的去除率先降低后升高,Pb²⁺的去除率的变化趋势与Cu²⁺类似。Zn²⁺去除率则随水体Zn²⁺初始浓度的升高而逐渐升高。菹草各器官对水体3种重金属离子的富集能力不同,排序为Cu²⁺＞Zn²⁺＞Pb²⁺。不同器官对同一种重金属离子的富集量差异显著,叶是富集重金属离子的主要器官。水体重金属离子的初始浓度会影响菹草各器官富集重金属离子的能力,一般随水体重金属初始浓度升高,菹草各器官的重金属离子富集量虽有不同程度的增加但富集系数持续减小。     

Biosorption of Heavy Metals (Cd2+, Cu2+, Co2+, and Mn2+) by Thermophilic Bacteria,Geobacillus thermantarcticus and Anoxybacillus amylolyticus: Equilibrium and Kinetic Studies

ABSTRACT

Two strains of thermophilic bacteria, Geobacillus thermantarcticus and Anoxybacillus amylolyticus, were employed to investigate the biosorption of heavy metals including Cd²⁺, Cu²⁺, Co²⁺, and Mn²⁺ ions. The effects of different biosorption parameters such as pH (2.0–10.0), initial metal concentrations (10.0–300.0 mg L^?1), amount of biomass (0.25–10 g L^?1), temperature (30–80°C), and contact time (15–120 min) were investigated. Concentrations of metal ions were determined by using an inductively coupled plasma optical emission spectrometry (ICP-OES). Optimum pHs for Cd²⁺, Cu²⁺, Co²⁺, and Mn²⁺ biosorption by Geobacillus thermantarcticus were found to be 4.0, 4.0, 5.0, and 6.0, respectively. For Anoxybacillus amylolyticus, the optimum pHs for Cd²⁺, Cu²⁺, Co²⁺, and Mn²⁺ biosorption were found to be 5.0, 4.0, 5.0, and 6.0, respectively. The Cd²⁺, Cu²⁺, Co²⁺, and Mn²⁺ removals at 50 mg L^?1 in 60 min by 50 mg dried cells of Geobacillus thermantarcticus were 85.4%, 46.3%, 43.6%, and 65.1%, respectively, whereas 74.1%, 39.8%, 35.1%, and 36.6%, respectively, for Anoxybacillus amylolyticus. The optimum temperatures for heavy metal biosorption were near the optimum growth temperatures for both strains. Scatchard plot analysis was employed to obtain more compact information about the interaction between metal ions and biosorbents. The plot results were further studied to determine if they fit Langmuir and Freundlich models.     

The role of antioxidants enzymes of E. coli ASU3, a tolerant strain to heavy metals toxicity, in combating oxidative stress of copper

The current study describes the isolation and characterization of E. coli from wastewater that collected from El-Malah canal in Assiut, Egypt. Twelve isolates were investigated for heavy metal resistance by which one of them showed multiple metal resistances. Furthermore, the bacterium was identified as E. coli ASU3 according to biochemical tests and then, preserved at Assuit University Mycological Centre with accession number AUMC B83. It exhibited high minimal inhibitory concentrations for metals and antibiotic resistance. The order of metals toxicity to the bacterium was Cr⁶⁺ > Cu²⁺ > Co²⁺ > Pb²⁺ > Ni²⁺ > Cr³⁺ > Cd²⁺ > Zn²⁺. Total protein content of E. coli ASU3 decreased with the increase of copper concentration. Under exposure of different concentrations of copper, the induction of antioxidant enzymes such as catalase, peroxidase and ascorbate peroxidase was increased and these antioxidant enzymes can contribute to combating oxidative stresses.     

Characterization of Desmodesmus pleiomorphus isolated from a heavy metal-contaminated site: biosorption of zinc

Microalgae have been proven efficient biological vectors for heavy metal uptake. In order to further study their biosorption potential, a strain of Desmodesmus pleiomorphus (L) was isolated from a strongly contaminated industrial site in Portugal. Under different initial Zn²⁺ concentrations, metal removal by that strain reached a maximum of 360 mg Zn/g biomass after 7 days, at 30 mg Zn/l, after an initial rapid phase of uptake. Comparative studies were carried out using a strain of the same microalgal species that is commercially available (ACOI 561): when exposed to 30 mg Zn/l, it could remove only 81.8 mg Zn/g biomass. Biosorption experiments using inactivated biomass of the isolated strain reached a maximum Zn²⁺ uptake of 103.7 mg/g. Metal removal at various initial pH values was studied as well; higher removal was obtained at pH 5.0. The microalga strain L, isolated from the contaminated site, exhibited a much higher removal capacity than the commercial strain, and the living biomass yielded higher levels of metal removal than its inactivated form.     

Biosorption of heavy metals by Bacillus thuringiensis strain OSM29 originating from industrial effluent contaminated north Indian soil

The study was navigated to examine the metal biosorbing ability of bacterial strain OSM29 recovered from rhizosphere of cauliflower grown in soil irrigated consistently with industrial effluents. The metal tolerant bacterial strain OSM29 was identified as Bacillus thuringiensis following 16S rRNA gene sequence analysis. In the presence of the varying concentrations (25–150 mgl⁻¹) of heavy metals, such as cadmium, chromium, copper, lead and nickel, the B. thuringiensis strain OSM29 showed an obvious metal removing potential. The effect of certain physico-chemical factors such as pH, initial metal concentration, and contact time on biosorption was also assessed. The optimum pH for nickel and chromium removal was 7, while for cadmium, copper and lead, it was 6. The optimal contact time was 30 min. for each metal at 32 ± 2 °C by strain OSM29. The biosorption capacity of the strain OSM29 for the metallic ions was highest for Ni (94%) which was followed by Cu (91.8%), while the lowest sorption by bacterial biomass was recorded for Cd (87%) at 25 mgl⁻¹ initial metal ion concentration. The regression coefficients obtained for heavy metals from the Freundlich and Langmuir models were significant. The surface chemical functional groups of B. thuringiensis biomass identified by Fourier transform infrared (FTIR) were amino, carboxyl, hydroxyl, and carbonyl groups, which may be involved in the biosorption of heavy metals. The biosorption ability of B. thuringiensis OSM29 varied with metals and was pH and metal concentration dependent. The biosorption of each metal was fairly rapid which could be an advantage for large scale treatment of contaminated sites.     

Modeling studies on mono and binary component biosorption of phenol and cyanide from aqueous solution onto activated carbon derived from saw dust

Biosorption is an effective treatment method for the removal of phenol and cyanide from aqueous solution by saw dust activated carbon (SDAC). Batch experiments were achieved as a function of several experimental parameters, i.e. influence of biosorbent dose (5–60 g/L) contact time (2–40 h), pH (4–12), initial phenol concentration (100–1000 mg/L) and initial cyanide concentration (10–100 mg/L) and temperature (20–40 °C). The biosorption capacities of the biosorbent were detected as 178.85 mg/g for phenol with 300 mg/L of initial concentration and 0.82 mg/g for cyanide with 30 mg/L of initial concentration. The optimum pH is found to be 8 for phenol and 9 for cyanide biosorption. The mono component biosorption equilibrium data for both phenol and cyanide were well defined by Redlich–Peterson model and binary component adsorption equilibrium data well fitted by extended Freundlich model. The percentage removal of phenol and cyanide using SDAC was 66.67% and 73.33%, respectively. Equilibrium established within 30 h for phenol and 28 h for cyanide. Kinetic studies revealed that biosorption of phenol followed pseudo second order indicating adsorption through chemisorption and cyanide followed pseudo first order kinetic model indicating adsorption through physisorption. Thermodynamic studies parameters, i.e., enthalpy (Δh₀), entropy (ΔS₀) and Gibb’s free energy (ΔG₀) have also been considered for the system. Thermodynamic modeling studies revealed that the process of cyanide biosorption was endothermic and phenol biosorption was exothermic in nature.     

Characterization of a vacuolar zinc transporter OZT1 in rice (Oryza sativa L.)

The CDF family is a ubiquitous family that has been identified in prokaryotes, eukaryotes, and archaea. Members of this family are important heavy metal transporters that transport metal ions out of the cytoplasm. In this research, a full length cDNA named Oryza sativa Zn Transporter 1 (OZT1) that closely related to rat ZnT-2 (Zn Transporter 2) gene was isolated from rice. The OZT1 encoding a CDF family protein shares 28.2 % ~ 84.3 % of identities and 49.3 % ~ 90.9 % of similarities with other zinc transporters such as RnZnT-2, HsZnT-8, RnZnT-8 and AtMTP1. OZT1 was constitutively expressed in various rice tissues. The OZT1 expression was significantly induced both in the seedlings of japonica rice Nipponbare and indica rice IR26 in response to Zn²⁺ and Cd²⁺ treatments. Besides, OZT1 expression was also increased when exposed to other excess metals, such as Cu²⁺, Fe²⁺ and Mg²⁺. Subcellular localization analysis indicated that OZT1 localized to vacuole. Heterologous expression of OZT1 in yeast increased tolerance to Zn²⁺ and Cd²⁺ stress but not the Mg²⁺ stress. Together, OZT1 is a CDF family vacuolar zinc transporter conferring tolerance to Zn²⁺ and Cd²⁺ stress, which is important to transporting and homeostasis of Zn, Cd or other heavy metals in plants.