Amperometric estimation of BOD by using living immobilized yeasts

Summary A microbial electrode consisting of immobilized living whole cells of yeasts, porous membrane and an oxygen electrode was prepared for continuous estimation of biochemical oxygen demand (BOD). Immobilized Trichosporon cutaneum was employed for the microbial electrode sensor for BOD. When a sample solution containing the equivalent amount of glucose and glutamic acid was injected into the sensor system, the current of the electrode decreased markedly with time until steady state was reached. The response time was within 18 min. A linear relationship was observed between the current decrease and the concentration below 41 mg l ^– of glucose and 41 mg l ^– glutamic acid (5-day BOD 60 mg l ^–). The current decrease was reproducible within ± 6% of the relative error when a sample solution containing 27 mg l ^– of glucose and 27 mg l ^– of glutamic acid (5-day BOD 40 mg l ^–) was employed. The microbial electrode sensor was applied to untreated waste waters from a fermentation factory. Good comparative results were obtained between BOD estimated by the microbial electrode and that determined by the conventional 5-day method (regression coefficient was 1.2). Furthermore, the effect of various compounds on BOD estimation was also examined. The current output of the microbial electrode sensor was almost constant for 17 d and 400 tests.     

Changes in phenol oxidation rate of a mixed microbial culture caused by sol-gel immobilization

A mixed microbial culture was entrapped into porous silica gel prepared by two different sol-gel methods. The immobilization of cells into prepolymerized tetraethoxysilane was more stressful to living microbial cells than the entrapment into colloidal SiO₂. Our experimental equipment operating in a sensor mode was able to detect 0.5 mg phenol l^–1 and had a linear response in the range from 2 to 10 mg phenol l^–1.     

Effects of tissue culture conditions and explant characteristics on direct somatic embryogenesis in Oncidium `Gower Ramsey'

The effects of tissue culture conditions and explant characteristics on direct somatic embryogenesis were studied on Oncidium `Gower Ramsey'. Embryo formation was significantly affected by explant position. Leaf tip segments had a significantly higher embryogenic response than other segments of leaves. Adaxial-side-up orientation significantly promoted embryogenesis in comparison with abaxial-side-up orientation. There was no significant effect of sucrose in a range of concentrations (10–60 g l^–1). Modified 1/2-MS medium (containing 85 mg l^–1 KH₂PO₄) supplemented with 170 mg l^–1 NaH₂PO₄ significantly promoted direct somatic embryogenesis. Peptone at 0.5 mg l^–1 gave significantly higher emrbyogenic response (80%) on leaf tips than control treatment (50%). The best response on direct embryo formation was obtained on the modified 1/2-MS medium supplemented with 10–20 g l^–1 sucrose, 170 mg l^–1 NaH₂PO₄ and 0.5 g l^–1 peptone.     

Analysis of micromolar concentrations of glucose by an interference free flow injection based biosensor

A fast, sensitive, interference-free, single enzyme single reagent glucose biosensor, operated in flow injection analysis (FIA) mode, was developed. The method used involved formation of colored complex of titanium sulfate reagent with the peroxide generated by glucose oxidase immobilized in a packed bed reactor. The color developed was detected spectrophotometrically in a flow cuvette. The system could measure down to 0.5 mg glucose l^–1 and the response was reproducible and linear in the range 1 mg l^–1 to 100 mg l^–1. The analysis time for a 500 l sample was 35 s and was free of interference from a number of substances tested. Analysis results using an off-line batch kit were observed to be in agreement with the developed system for determination of glucose in blood plasma samples.     

Electron transfer between galactose oxidase and an electrode via a redox polymer network

Galactose oxidase from Dactyllium dendroides was purified and immobilised on a carbon electrode in a redox polymer network of a polyvinylpyridine, partially N-complexed with osmiumbis(bipyridine)chloride (POsEA). The current density of the electrodes depended on the concentration of phosphate elution buffer. By additional crosslinking with a 1% glutaraldehyde solution in 50 mM phosphate buffer, pH 7.0, an electrode with an initial current density of 0.8 mA/cm² was obtained. Operational half life times were in the order of 1.2 h. The affinity of the immobilized enzyme for galactose,lactose, raffinose, glycerol and dihydroxyaceton was higher than described in literature for the enzyme in solution. Optimal temperature for the enzyme electrode was 30°C. The pH optimum for the immobilized enzyme was higher than for the enzyme in solution.     

Determination of quinolones in plasma samples by capillary electrophoresis using solid-phase extraction

The potential of capillary zone electrophoresis (CZE) and micellar electrokinetic capillary chromatography (MEKC) have been investigated for the separation and quantitative determination of 10 quinolone antibiotics. The influence of different conditions, such as the buffer and pH of the electrolyte, the surfactant and the ion-pairing agents added to the electrolyte and the organic modifier were studied. A buffer consisting of 40 mM sodium tetraborate at pH 8.1 containing 10% (v/v) methanol was found to be a highly efficient electrophoretic system for separating lomefloxacin, enoxacin, norfloxacin, pipemidic acid, ofloxacin, piromidic acid, flumequine, oxolinic acid, cinoxacin and nalidixic acid. A solid-phase extraction method to remove the sample matrix (pig plasma samples) was developed on a C₁₈ cartridge using a mixture of methanol–water (70:30, v/v). The method is specific and reproducible and mean recoveries were in the range 94.0±4.2% and 123.3±4.1% for pig plasma samples over the range used. A linear relationship between concentration and peak area for each compound in pig plasma samples was obtained in the concentration range 5–20 mg l⁻¹ and detection limits were between 1.1 and 2.4 mg l⁻¹.     

A novel biosensor based on l-homocysteine desulfhydrase enzyme immobilized in eggshell membrane

A novel biosensor for homocysteine determination has been developed. The biosensor was fabricated with l-homocysteine desulfhydrase immobilized on the ammonium selective electrode by means of eggshell membrane. The measurement principle is based on determination of ammonia due to the enzymatic reaction in the medium by ammonium selective electrode. The effects of enzyme loading, glutaraldehyde concentration, pH, buffer concentration, temperature, dithiotreitol (DTT) concentration and ionic strength adjustment buffer (ISA) on the biosensor response were investigated in detail. The linear detection range and limit of detection (LOD) for homocysteine were found to be 0.15–1.8 mM and 55 μM, respectively. Finally, the homocysteine biosensor has been applied to plasma samples for determination of total homocysteine contents.     

Simultaneous high-performance liquid chromatographic determination of quinupristin, dalfopristin and their main metabolites in human plasma

Quinupristin–dalfopristin (30:70, w/w) is a new streptogramin, which has been developed for intravenous use. A specific and sensitive HPLC method was developed to measure simultaneously quinupristin (RP 57669) and dalfopristin (RP 54476) and their main metabolites in human plasma. The metabolites measured by this method were RP 69012 (glutathione-conjugated) and RPR 100391 (cysteine-conjugated) from quinupristin and RP 12536 (natural pristinamycin IIA), from dalfopristin. Solid-phase extraction with disposable cartridges was combined with reversed-phase HPLC and fluorimetric detection for RP 57669, RP 69012 and RPR 100391 and UV detection for RP 54476 and RP 12536. The method provided good recovery and low limits of quantitation (0.025 mg l⁻¹ for RP 57669, RP 54476 and RP 12536, and of 0.010 mg l⁻¹ for RP 69012 and RPR 100391). The validated range of concentrations of the method was: 0.025–5000 mg l⁻¹ for RP 57669, RP 54476 and RP 12536 and 0.010–0.750 mg l⁻¹ for RP 69012 and RPR 100391.     

Physical and chemical characteristics of the Blue Nile and the White Nile at Khartoum

Fortnightly measurements of physical and chemical variables were made at two locations on the Blue and White Niles near Khartoum from August 1968 to December 1970. Variables analysed from each river were: temperature, pH, total residue, current velocity, oxygen, alkalinity, phosphate, nitrate, ammonia, silica, sulphate, iron, calcium, magnesium, sodium, potassium and oxidizable organic matter. The seasonal variations of these factors in the two Niles are compared and the interrelationships existing between some of them are discussed. Comparisons with earlier studies on the Nile and with some tropical rivers are made.In the Blue Nile, the amounts of suspended matter and nutrients are largely dependent upon the flood regime. Nitrate, phosphate, iron, oxidizable organic matter and total residue increase considerably in the Blue Nile when the river is in flood (peaks: 1 880 µg NO₃-N l^–1; 0.31 mg Fe l^–1; 3 842 mg total residue · l^–1).In the White Nile, concentrations of nitrate, phosphate, iron, oxidizable organic matter and total residue attain their peaks during the rainy season (270 µg NO₃-N l^–1; 163 tag PO₄-P l^–1; 0.46 mg Fe · l^–1; 502 mg total residue · l^–1).In both rivers, alkalinity, calcium, sodium and potassium tend to increase during the dry season while declining in the rainy season. Silica is depleted at certain times of the year, yet relatively high concentrations are maintained throughout the year and were not expected to limit growth of diatoms. Fall in silica concentrations, unlike nitrate, phosphate and iron, was always followed by a rapid restoration of a high level. Silica and magnesium showed no response to changes in discharge rates.     

Separation and simultaneous determination of nalidixic acid, hydroxynalidixic acid and carboxynalidixic acid in serum and urine by micellar electrokinetic capillary chromatography

Separation in capillary electrophoresis is governed by various factors, including buffer type, buffer concentration, pH, temperature, voltage and micelles. Through proper adjustment of these parameters, nalidixic acid and its two major metabolites, 7-hydroxynalidixic and 7-carboxynalidixic, could be separated by micellar electrokinetic capillary chromatography using an electrophoretic electrolyte consisting of 50 mM borate buffer (pH 9) containing 25 mM sodium dodecyl sulphate and 10% acetonitrile. A linear relationship between concentration and peak area for each compound was obtained in the concentration range 0.15–100 μg ml⁻¹, with a correlation coefficient greater than 0.999 and detection limits in the 0.2–0.7 ng ml⁻¹ range. Intra- and inter-day precision values of about 0.8–1.2% RSD (n=11) and 1.3–2.0% RSD (n=30), respectively, were obtained. The method has been applied to the analysis of nalidixic acid and its two major metabolites in serum and urine with limits of sensitivity lower than 0.8 ng ml⁻¹.     

Enzymes related to galactose utilization inPseudomonas cepacia

Pseudomonas cepacia produced a characteristic green sheen on EMB-galactose plates owing to production of galactonic acid by the constitutive membrane-associated glucose dehydrogenase of this bacterium. Mutants isolated as glucose dehydrogenase deficient (Gcd^–) also were deficient in membrane-associated galactose dehydrogenase. A strain that formed glucose dehydrogenase at 30°C but not at 40°C was also temperature sensitive with respect to formation of galactose dehydrogenase. The Gcd^– strains still utilized galactose. A second, NAD-specific, galactose dehydrogenase (not membrane associated) along with a transport system for galactose were induced during growth on galactose and constituted an alternative pathway of conversion of galactose to galactonate. Enzymes of the De Ley-Doudoroff pathway of conversion of galactonate to pyruvate and glyceraldehyde-3-phosphate were induced during growth on galactose. Unexpectedly, growth on galactose also elicited formation of enzymes of the Entner-Doudoroff (ED) route. Furthermore, mutants blocked in the ED pathway grew poorly on galactose. One interpretation of these findings is that glyceraldehyde-3-phosphate formed from galactose via the De Ley-Doudoroff route (by cleavage of 2-keto-3-deoxy-6-phosphogalaconate) is reconverted to hexose phosphate and metabolized via the ED pathway.     

Biodegradation and detoxification of nicotine in tobacco solid waste by a Pseudomonas sp.

A Pseudomonas sp. grew with nicotine optimally 3 g l^–1 and at 30 °C and pH 7. Nicotine was fully degraded within 10 h. The resting cells degraded nicotine in tobacco solid waste completely within 6 h in 0.02 m sodium phosphate buffer (pH 7) at maximally 56 mg nicotine h^–1 g dry cell^–1.     

Application of cyanide hydrolase from Klebsiella sp. in a biosensor system for the detection of low-level cyanide

Abstract A partially purified preparation of cyanide hydrolase (cyanidase) from a bacterium, Klebsiella sp., was applied as a biocatalyst in a biosensor system for low-level cyanide detection. In the biosensor system cyanide hydrolase converts cyanide into formate and ammonia. The formate produced in the cyanide degradation was detected with a formate biosensor, in which formate dehydrogenase (FDH; E.C. 1.2.1.2) was co-immobilized with salicylate hydroxylase (SHL; E.C. 1.14.13.1) on a Clark electrode. The principle of the formate sensor is that FDH converts formate into carbon dioxide using -nicotinamide adenine dinucleotide hydrate (NAD⁺). The corresponding NADH produced is then oxidized to NAD⁺ by SHL using salicylate and oxygen. The oxygen consumption is monitored with the Clark electrode. The optimum buffer pH and temperature for the enzymatic hydrolysis of potassium cyanide were studied. The preliminary experiments including the pretreatment of cyanide with cyanide hydrolase and then detection by the formate sensor gave a detection limit at 7.3 mol l^–1 cyanide. The linear range of the calibration curve was between 30 mol l^–1 and 300 mol l^–1 cyanide.     

Aerotaxis and chemotaxis ofAzospirillum brasilense: A note

Azospirillum brasilense was attracted to capillaries containing either phosphate buffer, distilled water, or saline. The number of bacteria in these capillaries was 3–4×10⁴, after 1 h of incubation. In the presence of phosphate buffer + attractants, the number of cells accumulated in the capillary increased only to 5×10⁴–1.1×10⁵ cells. It was not possible, therefore, to measure chemotaxis inA. brasilense as distinct from aerotaxis by the capillary method. Chemotaxis was observed in semi-solid agar plates and was determined by a growth band oriented towards the attractant. Positive chemotactic response was obtained with peptone, tryptone, yeast extract, amino acids, organic acids, arabinose and galactose.     

Somatic embryogenesis in loblolly pine (<Emphasis Type="Italic">Pinus taeda</Emphasis>) and Douglas fir (<Emphasis Type="Italic">Pseudotsuga menziesii</Emphasis>): improving culture initiation and growth with MES pH buffer,biotin, and folic acid

Loblolly pine (Pinus taeda L.) somatic embryogenesis initiation was improved by supplementing the initiation medium with the pH buffer agent 2(n-morpholino)ethanesulphonic acid (MES) at 250 mg l^–1, folic acid at 0.5 mg l¹, and biotin at 0.05 mg l^–1. MES and vitamins increased the percentage of explants with extruded tissue that continued the initiation process to form embryogenic tissue. The increase in initiation was about 12%. Initiation of 12 open-pollinated families averaged 38.5%, which is 16% higher than initiation on medium without these additives. When tested with 18 control-pollinated families, initiation averaged 26.3%. Basal medium contained a combination of modified 1/2 P6 salts, activated carbon (AC) at 50 mg ^–1, Cu and Zn adjusted to compensate for adsorption by AC, 1.5% maltose, 2% myo-inositol, 500 mg l^–1 casamino acids, 450 mg l^–1 glutamine, 2 mg l^–1 NAA, 0.63 mg l^–1 BAP, 0.61 mg l^–1 kinetin, 3.4 mg l^–1 silver nitrate, 10 M 8-Br-cGMP, 0.1 M brassinolide, and 2 g l^–1 Gelrite. Early-stage embryo growth and initiation in Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) were also improved in the presence of these additives.     

Colorimetric method for the determination of ethanol by Flow Injection Analysis

An automated Flow Injection Analysis system using stop-flow technique for quantifying ethanol based in a colorimetric detection method was developed. The system permitted analysis in a linear range of 0.05–1 g ethanol l^–1 without external dilution, a sampling frequency of 15 analyses per hour, and a relative standard deviation of 3.5%. A dilution line was implemented in the FIA system permitting the extension of the linear range to 0.5–5.2 g ethanol l^–1 maintaining the same sampling frequency and standard deviation. The system was applied to measure ethanol concentrations present in samples of an alcoholic fermentation and the results showed no significant difference with other analytical procedures (GC).     

Food consumption of Sarotherodon mossambicus (Trewaves) exposed to sublethal concentration of diammonium phosphate

S. mossambicus was exposed to toxic and sublethal concentrations of the fertilizer diammonium phosphate (0.2 to 1.0 g l^–1). Mortality, food utilization and growth were studied. At a concentration of 0.6 g l^–1 DAP, 100% mortality was observed within 96 h; no mortality occurred at 0.5 g l^–1; LC50 was 0.55 g l^–1. Rearing the fish in increasing sublethal concentrations of DAP, it was found that the feeding rate decreased from 25.4 mg g^–1 fish^–1 d^–1 (fish reared in DAP-free water) to 10.1 mg g^–1 d^–1 at the highest sublethal concentration (0.5 g l^–1). Growth rate was drastically reduced. At high sublethal concentrations of DAP, the fish lost reserve energy, in addition to the energy obtained from food intake for survival, as a result of increased swimming activity and opercular beats.     

Development of haploid asparagus embryos from liquid cultures of anther-derived calli is enhanced by ancymidol

Summary The effect of ancymidol concentration on the development of haploid asparagus embryos was determined. Liquid cultures from anther-derived calli were grown for three weeks in MS medium plus 1.0 mg l^–1 2,4-D, 0.1 mg l^–1 NAA, 0.2 mg l^–1 kinetin, 800 mg l^–1 glutamine, 500 mg l^–1 casein hydrolysate, 2% sucrose and 0.0–1.0 mg l^–1 ancymidol. Cell clumps (224–500 m) were plated on solid embryo maturation medium (MS medium plus 3% sucrose, 0.1 mg l^–1 NAA, 0.5 mg l^–1 kinetin and 0.0–1.0 mg l^–1 ancymidol) and grown for eight weeks. Ancymidol enhanced embryo maturation and germination and was more critical in the solid than liquid medium. Total embryo number did not vary among most treatments. The best response was observed when ancymidol concentrations were 0.1 and 0.5 mg l^–1 in the liquid and solid media, respectively; two-thirds of the embryos produced were bipolar and 35% of bipolar embryos germinated. Seven to 82% of plants recovered from different ancymidol treatments were haploid; the others were diploid, triploid or chimeric for ploidy level.Abbreviations NAA naphthaleneacetic acid - 2,4-D 2,4-dichlorophenoxyacetic acid - GA₃ gibberellic acid - MS Murashige and Skoog (1962)     

Production of crocin using Crocus sativus callus by two-stage culture system

Saffron callus was grown in a two-stage culture on B5 medium supplemented with casein hydrolysate (300 mg l^–1) at 22 °C in dark with naphthalene acetic acid (2 mg l^–1) and 6-benzyladenine (1 mg l^–1) to give maximum biomass (16 g dry wt l^–1), and with indole 3-acetic acid (2 mg l^–1) and 6-benzyladenine (0.5 mg l^–1) for crocin formation. The maximum crocin production (0.43 g l^–1) was achieved by this two-stage culture method, which was three times that by a one-stage method.     

Measurement of chloramphenicol by capillary zone electrophoresis following end-column amperometric detection at a carbon fiber micro-disk array electrode

Capillary zone electrophoresis was employed for the measurement of chloramphenicol using end-column amperometric detection with a carbon fiber micro-disk array electrode, at a constant potential of −1.00 V vs. saturated calomel electrode. The effect of oxygen in the buffer has been investigated. It is found that when the area of the carbon fiber electrode is smaller than 1.1 mm², the interference of oxygen can be overcome. In this procedure deoxygenation is not necessary. The effect of pH, the concentration of the buffer and the high separation voltage across the capillary on the migration time, electrophoretic peak current and separation efficiency has been studied. The optimum conditions of separation and detection are 8.4×10⁻⁴ mol/l HOAc–3.2×10⁻³ mol/l NaOAc for the buffer solution, 20 kV for the separation voltage, 5 kV and 5 s for the injection voltage and the injection time, respectively. The calibration plot was found to be linear in the range 5×10⁻⁶ to 1×10⁻³ mol/l and the limit of detection is 9.1×10⁻⁷ mol/l or 1.4 fmol (S/N=2). The relative standard deviation is 1.1% for the migration time and 2.3% for the electrophoretic peak current. The method was applied to the determination of chloramphenicol in human serum.