Microwave pretreatment of rape straw for bioethanol production: focus on energy efficiency

The energy efficiency of microwave-assisted dilute sulfuric acid pretreatment of rape straw for the production of ethanol was investigated. Different microwave energy inputs and solid loadings were tested to find economic pretreatment conditions. The lowest energy consumption was observed when solid loading and energy input were fixed at 50% (w/w) and 54 kJ (900 W for 1 min), respectively, and amounted to 5.5 and 10.9 kJ to produce 1 g of glucose after enzymatic hydrolysis and 1 g ethanol after fermentation, respectively. In general, 1 g ethanol can produce about 30 kJ of energy, and therefore, the energy input for the pretreatment was only 35% of the energy output. The approach developed in this study resulted in 92.9% higher energy savings for producing 1 g ethanol when compared with the results of microwave pretreatments previously reported.     

Optimisation of a microwave pretreatment of wheat straw for methane production

This study aims at the optimisation of a microwave pretreatment for wheat straw solubilisation and anaerobic biodegradability. The maximum yield of methane production was obtained at 150 °C with an improvement of 28% compared to an untreated sample. In addition, at this temperature, the time to reach 80% of the methane volume obtained from untreated straw was about 35%. The study of ramp time and holding time at targeted temperature showed that they had no improvement effect. Thus, the best conditions are the highest heating rate for a final temperature 150 °C without any holding time. The reading of energy consumed by pretreatment and energy overproduced by pretreated samples showed that increasing tVS amount and heating rate led to a saving of energy consumption. Nevertheless, to obtain a positive energy balance, a microwave device should consume less than 2.65 kJ/g_tVS.     

Microwave-Assisted Extraction of Wax from Oily Sludge: An Experimental Study and its Process Variables Optimization Using Response Surface Methodology

The wax present in petroleum sludge, generated by refineries and at crude production sites, consists of paraffin hydrocarbons (C18–C36) known as paraffin wax and naphthenic hydrocarbons (C30–C60). The present study is aimed at the recovery of wax from petroleum oily sludge by microwave-assisted solvent extraction using a Toluene/MEK mixture and subsequently de-crystallizing the wax. The process variables affecting the microwave-assisted solvent extraction are optimized for recovery of wax. The simultaneous effects of process variables such as irradiation time (2–10 minutes), solvent to sludge ratio (40–80 wt%), reactant volume (100–300 ml), and microwave power (80–400 W) on the recovery of wax were evaluated. A central composite design and response surface methodology were used for the optimization of the extraction process. Based on the central composite design, quadratic models were developed to correlate the extraction process variables with the responses and the models were analyzed using appropriate statistical methods for analysis of variance. Optimization of process variables shows the maximum recovery of wax was about 79.57% at 300 ml of reactant volume with microwave power output of 400 W at 7.6 minutes of retention time with 56.56% of Toluene/MEK to sludge ratio.     

Characteristics of microwave evoked body movements in mice

Microwave evoked body movements were studied in mice. A resonant cavity was used to provide head and neck exposure of the mouse to pulsed and gated continuous wave (CW) 1.25 GHz microwaves. No difference in response to pulsed and gated CW stimuli of equal average power was found. The incidence of the microwave evoked body movements increased proportionally with specific absorption (dose) when the whole-body average specific absorption rate was at a constant level (7300 W/kg). Under a constant average specific absorption rate, the response incidence reached a plateau at 0.9 kJ/kg. For doses higher than 0.9 kJ/kg, response incidence was proportional to the specific absorption rate and reached a plateau at 900 W/kg. Body movements could be evoked by a single microwave pulse. The lowest whole-body specific absorption (SA) tested was 0.18 kJ/kg, and the corresponding brain SA was 0.29 kJ/kg. Bulk heating potentials of these SAs were less than 0.1 °C. For doses higher than 0.9 kJ/kg, the response incidence was also proportional to subcutaneous temperature increment and subcutaneous heating rate. The extrapolated absolute thresholds (0% incidence) were 1.21 °C temperature increment and 0.24 °C/s heating rate. Due to high subcutaneous heating rates, these microwaves must be perceived by the mouse as an intense thermal sensation but not a pain sensation because the temperature increment was well below the threshold for thermal pain. Results of the present study should be considered in promulgation of personnel protection guideline against high peak power but low average power microwaves. © 1994 Wiley-Liss, Inc.     

Microwave, ultrasonic and chemo-mechanical pretreatments for enhancing methane potential of pulp mill wastewater treatment sludge

Microwave (2450 MHz, 1250 W), ultrasonic (20 kHz, 400 W) and chemo-mechanical (MicroSludge® with 900 mg/L NaOH followed by 83,000 kPa) pretreatments were applied to pulp mill waste sludge to enhance methane production and reduce digester sludge retention time. The effects of four variables (microwave temperature in a range of 50-175 °C) and sonication time (15-90 min), sludge type (primary or secondary) and digester temperature (mesophilic and thermophilic) were investigated. Microwave pretreatment proved to be the most effective, increasing specific methane yields of WAS samples by 90% compared to controls after 21 days of mesophilic digestion. Sonication solubilized the sludge samples better, but resulted in soluble non-biodegradable compounds. Based on the laboratory scale data, MicroSludge® was found the least energy intensive pretreatment followed by sonication for 15 min alternative with net energy profits of 1366 and 386 kWh/tonne of total solids (TS), respectively. Pretreatment benefits were smaller for thermophilic digesters.     

Heat transfer analysis of Staphylococcus aureus on stainless steel with microwave radiation

Staphylococcus aureus (NCTC 6571; Oxford strain) on stainless steel discs was exposed to microwave radiation at 2450 MHz and up to 800 W. Cell viability was reduced as the exposure time increased, with complete bacterial inactivation at 110 s, attaining a temperature of 61.4 degrees C. The low rate of temperature rise, RT, of the bacterial suspension as compared with sterile distilled water or nutrient broth suggests a significant influence of the microwave sterilization efficacy on the thermal properties of the micro-organisms. The heat transfer kinetics of thermal microwave irradiation suggest that the micro-organism has a power density at least 51-fold more than its surrounding liquid suspension. When the inoculum on the stainless steel disc was subjected to microwave radiation, heat conduction from the stainless steel to the inoculum was the cause of bacteriostasis with power absorbed at 23.8 W for stainless steel and 0.16 W for the bacteria-liquid medium. This report shows that the microwave killing pattern of Staph. aureus on stainless steel was mainly due to heat transfer from the stainless steel substrate and very little direct energy was absorbed from the microwaves.     

Dissolution of cellulose with NMMO by microwave heating

Environmentally friendly microwave heating process was applied to the dissolution of cellulose in N-methylmorpholine-N-oxide (NMMO) with 105–490 W and 2450 MHz microwave energy until the dissolution completed. Microwave heating caused the decrease in the dissolution time and energy consumption. Cellulose/NMMO/water solutions with different cellulose concentrations were converted to the membrane to measure the crystallinity and degree of polymerization. It was shown that microwave heating with the power of 210 W is an alternative heating system for dissolution of cellulose in NMMO. The membranes obtained with two different heating methods showed the same crystallinity and degree of polymerization. As a result, microwave heating has an advantage in shortening reaction times, compared to conventional heating.     

Applications of microwave dielectric heating in environment-related heterogeneous gas-phase catalytic systems

The application of microwave dielectric heating in a range of environment-related heterogeneous catalytic reaction systems has been reviewed. The reactions investigated include the decomposition of hydrogen sulfide, the reduction of sulfur dioxide with methane, the reformation of methane by carbon dioxide, the hydrodesulfurization of thiophene, and the oxidative coupling of methane. The interaction of microwave irradiation with heterogeneous catalytic systems and its consequence for the microwave heating behaviour of catalysts have been examined. The effect/mechanism of microwave dielectric heating on heterogeneous catalytic reaction systems has also been discussed.     

Different effects of microwave energy and conventional heat on the activity of a thermophilic beta-galactosidase from Bacillus acidocaldarius

The effect of microwave (f = 10.4 GHz) irradiation on a thermostable enzyme was experimentally tested, showing that irreversible inactivation is obtained. Enzymatic solutions (500 microliters, with concentrations between 10-100 micrograms/ml) were exposed at 70 degrees C, at SAR levels of 1.1 and 1.7 W/g for 15, 30, 45, or 60 min, and their activity was compared to that of a sample heated in a water bath at the same temperature. The residual activity of the exposed samples depends on enzyme concentration, microwave power level, and exposure time; activity was reduced to 10% in 10 micrograms/ml solutions treated at 1.7 W/g for 60 min. Microwave effects disappeared at concentrations above 50 micrograms/ml. These results were not found following water bath heating at the same temperature and durations.     

The action of microwave radiation on potassium ion transport and oxygen consumption in the perfused rat liver

Changes induced by the effect of microwave irradiation (2450 MHz, specific absorbed power from 0.1 to 5 W/g, continuous and pulsed-modulated regime) on potassium ion transport and oxygen consumption in the perfused liver do not virtually differ from those induced by heating the perfusate: this is indicative of a "thermal" mechanism of action of microwave radiation.     

响应面法优化微波辅助提取枇杷叶中黄酮类化合物

为充分利用枇杷叶,研究微波辅助乙醇浸提法从枇杷叶中提取黄酮类化合物的工艺。首先研究了影响提取效果的因素:不同体积分数的乙醇溶液、料液比、时间及微波功率。在单因素试验基础上利用响应面分析法,确定了各因素与总黄酮得率之间的关系,并以总黄酮得率为响应值做响应面和等高线图。研究表明,枇杷叶中黄酮类化合物提取最佳工艺为乙醇体积分数50%,料液比1∶30,提取时间3 min,微波功率500 W,最佳条件下总黄酮得率为2.04%,与理论推导值2.07%相比,误差为1.4%,黄酮类化合物响应方程的回归分析表明此方法合理可行。本研究对枇杷叶总黄酮提取优化的研究为进一步探讨枇杷叶的深度开发提供了理论参考依据,并为枇杷叶总黄酮的生物活性研究提供材料。     

Microwave-assisted preparation and adsorption performance of activated carbon from biodiesel industry solid reside: influence of operational parameters

Preparation of activated carbon has been attempted using KOH as activating agent by microwave heating from biodiesel industry solid residue, oil palm empty fruit bunch (EFBAC). The significance of chemical impregnation ratio (IR), microwave power and activation time on the properties of activated carbon were investigated. The optimum condition has been identified at the IR of 1.0, microwave power of 600 W and activation time of 7 min. EFBAC was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy and nitrogen adsorption isotherm. The surface chemistry was examined by zeta potential measurement, determination of surface acidity/basicity, while the adsorptive property was quantified using methylene blue as dye model compound. The optimum conditions resulted in activated carbon with a monolayer adsorption capacity of 395.30 mg/g and carbon yield of 73.78%, while the BET surface area and total pore volume were corresponding to 1372 m²/g and 0.76 cm³/g, respectively.     

Thermal action of 2.45 GHz microwaves on the cytoplasm of Chinese hamster cells

In order to demonstrate possible specific effects of microwaves at the cellular level V-79 Chinese hamster cells were exposed to 2.45-GHz radiation at power levels of 20–200 mW/cm² and at specific absorption rates of 10–100 mW/g. Intracellular cytoplasmic changes were observed by fluorescence polarization using a method based on the intracellular enzymatic hydrolysis of nonfluorescent fluorescein diacetate (FDA). At levels of absorbed energy below 90 J/g, modifications of microviscosity and mitochondrial state were absent, but a slight stimulation of enzymatic hydrolysis of FDA was observed which may be explained by microwave-induced alterations of cellular membranes possibly due to differences in heating pattern of microwaves compared to water-bath heating. At levels of absorbed energy above 90 J/g, the decrease of enzymatic hydrolysis of FDA, increase in degree of polarization, and increase of permeation of the fluorescent marker correlated well with the decrease in cell viability as measured by the exclusion of trypan blue. At equal absorbed energy, microwaves were found to exert effects comparable to classical heating except that permeation was slightly more affected by microwave than by classical heating. This suggests that membrane alteration produced by microwaves might differ from those induced by classical heating or that microwaves may have heated the membrane to higher temperatures than did classical heating.     

Eliminating non-renewable CO2 emissions from sewage treatment: an anaerobic migrating bed reactor pilot plant study

The aim of this work was to demonstrate at pilot scale a high level of energy recovery from sewage utilising a primary Anaerobic Migrating Bed Reactor (AMBR) operating at ambient temperature to convert COD to methane. The focus is the reduction in non-renewable CO(2) emissions resulting from reduced energy requirements for sewage treatment. A pilot AMBR was operated on screened sewage over the period June 2003 to September 2004. The study was divided into two experimental phases. In Phase 1 the process operated at a feed rate of 10 L/h (HRT 50 h), SRT 63 days, average temperature 28 degrees C and mixing time fraction 0.05. In Phase 2 the operating parameters were 20 L/h, 26 days, 16 degrees C and 0.025. Methane production was 66% of total sewage COD in Phase 1 and 23% in Phase 2. Gas mixing of the reactor provided micro-aeration which suppressed sulphide production. Intermittent gas mixing at a useful power input of 6 W/m(3) provided satisfactory process performance in both phases. Energy consumption for mixing was about 1.5% of the energy conversion to methane in both operating phases. Comparative analysis with previously published data confirmed that methane supersaturation resulted in significant losses of methane in the effluent of anaerobic treatment systems. No cases have been reported where methane was considered to be supersaturated in the effluent. We have shown that methane supersaturation is likely to be significant and that methane losses in the effluent are likely to have been greater than previously predicted. Dissolved methane concentrations were measured at up to 2.2 times the saturation concentration relative to the mixing gas composition. However, this study has also demonstrated that despite methane supersaturation occurring, micro-aeration can result in significantly lower losses of methane in the effluent (<11% in this study), and has demonstrated that anaerobic sewage treatment can genuinely provide energy recovery. The goal of demonstrating a high level of energy recovery in an ambient anaerobic bioreactor was achieved. An AMBR operating at ambient temperature can achieve up to 70% conversion of sewage COD to methane, depending on SRT and temperature.     

Kinetic Simulations of EC Plasma Heating and Current Drive in the L-2M Stellarator

The ECHLAB code, intended for a self-consistent numerical analysis of the evolution of the electron distribution function and the spatial structure of the electromagnetic field during EC plasma heating in a stellarator, is described. The results from calculations of plasma heating and current drive under conditions corresponding to experiments on EC plasma heating by an X2-mode in the L-2M stellarator are presented. It is shown that, at the existing level of microwave power, the energy deposition region displaces only slightly during heating. The energy is mainly absorbed by relatively fast passing electrons. The influence of locally trapped electrons on the efficiency of current drive is insignificant.     

Glutathione concentration and peptidase activity in the lens after exposure to microwaves

This study was undertaken for observation of early changes in glutathione concentration and the activity of carboxypeptidase A and aminopeptidase in the cortex and core of the lens as well as for determination of the cumulating effect of microwave energy after repeated exposures to microwaves. Experiments were carried out on New Zealand rabbits. The control group was compared to experimental groups exposed every day for 5 minutes to microwave irradiation of the eyeballs at power densities of 5 X 10(-3) W/cm2 and 10 X 10(-3) W/cm2 during 10, 20 and 30 days. Differences were found between the control group and the groups of animals exposed to microwaves in which the glutathione concentration in the cortex and core of the lens was decreasing with time in proportion to the number of exposures. Parallelly to the number of days of exposure to microwaves the enzymatic activity of carboxypeptidase A and aminopeptidase increased in the cortex of the lens. The observed changes demonstrate cumulation of the absorbed microwave energy leading to changes in the permeability of the capsule and membranes of lenticular fibres which lead to secondary metabolic disturbances in the lens of the eye.     

Rapid Bielschowsky silver impregnation method using microwave heating

The Bielschowsky silver impregnation method has been used extensively to demonstrate neuronal processes including dendrites, axons and neurofibrils. In this study, we examined the differences in the time required for and the staining quality of the Bielschowsky method for neuronal processes when microwave heating was used instead of processing at room temperature. For this purpose, a control group of sections stained according to the conventional method at room temperature was compared to an experimental group stained in a microwave oven at 180 W for 2, 4 and 1 min in 2% silver nitrate, ammoniacal silver nitrate and gold chloride, respectively. Light microscopic examination demonstrated that the normal structure was preserved in both groups and that there was no difference in the staining quality between the control and the microwave groups. In addition, staining time for this procedure was reduced to 8 min by using the microwave oven. Our study revealed that microwave irradiation can be used safely for Bielschowsky silver impregnation of neuronal tissues.     

Rapid Bielschowsky silver impregnation method using microwave heating

The Bielschowsky silver impregnation method has been used extensively to demonstrate neuronal processes including dendrites, axons and neurofibrils. In this study, we examined the differences in the time required for and the staining quality of the Bielschowsky method for neuronal processes when microwave heating was used instead of processing at room temperature. For this purpose, a control group of sections stained according to the conventional method at room temperature was compared to an experimental group stained in a microwave oven at 180 W for 2, 4 and 1 min in 2% silver nitrate, ammoniacal silver nitrate and gold chloride, respectively. Light microscopic examination demonstrated that the normal structure was preserved in both groups and that there was no difference in the staining quality between the control and the microwave groups. In addition, staining time for this procedure was reduced to 8 min by using the microwave oven. Our study revealed that microwave irradiation can be used safely for Bielschowsky silver impregnation of neuronal tissues.     

微波提取香水莲花总黄酮的工艺研究

该文研究了微波法提取香水莲花总黄酮的工艺。采用比色法测定黄酮的含量。利用单因素实验和正交实验考察了乙醇浓度、微波功率、微波时间、料液比对黄酮得率的影响,确定了最佳工艺为:用70%的乙醇溶液,微波功率250W,提取时间40 min,液料比25∶1,提取的总黄酮得率最高。     

Cellulose esters from waste cotton fabric via conventional and microwave heating

The esterification of cellulose from waste cotton fabric in a N,N-dimethylacetamide/lithium chloride solvent system was carried out using different types of fatty acid chloride including butyryl chloride, capryloyl chloride, and lauroyl chloride as esterifying agents, and N,N-dimethyl 1-4-aminopyridine as a catalyst under conventional and microwave activation. Microwave esterification was performed under 2.45 GHz with power varying from 90 to 450 W. The optimum conditions for esterification of cotton cellulose with various esterifying agents were investigated in terms of reaction time and temperature to attain appropriate %weight increase and degree of substitution of esterified-cellulose. The degree of substitution, functional group and chemical structure, and thermal stability of cellulose ester powder were characterized by ¹H NMR, FTIR, and TGA/SDTA analysis. Morphologies, crystallinity, and solubility of modified cellulose by two different heating methods were compared.