Fabrication of chronocoulometric DNA sensor based on gold nanoparticles/poly(l-lysine) modified glassy carbon electrode

In this work, we fabricated a sensitivity chronocoulometric DNA sensor (CDS) based on gold nanoparticles (AuNPs)/poly(l-lysine) complex film modified glassy carbon electrode. Hexaammineruthenium(III) chloride ([Ru(NH₃)₆]³⁺) was used as the electroactive indicator. The assembled process was investigated by cyclic voltammetry (CV) and chronocoulometry (CC). CC is used to monitor the DNA hybridization event by measurement of electrostatic binding [Ru(NH₃)₆]³⁺. Under the optimal conditions, the signal of [Ru(NH₃)₆]³⁺ was linear with the logarithm of the concentration of the complementary oligonucleotides from 1.0 × 10⁻¹³ to 1.0 × 10⁻¹¹ M, and the detection limit is 3.5 × 10⁻¹⁴ M.     

[Cu(phen)2] acts as electrochemical indicator and anchor to immobilize probe DNA in electrochemical DNA biosensor

We demonstrate a novel protocol for sensitive in situ label-free electrochemical detection of DNA hybridization based on copper complex ([Cu(phen)₂]²⁺, where phen = 1,10-phenanthroline) and graphene (GR) modified glassy carbon electrode. Here, [Cu(phen)₂]²⁺ acted advantageously as both the electrochemical indicator and the anchor for probe DNA immobilization via intercalative interactions between the partial double helix structure of probe DNA and the vertical aromatic groups of phen. GR provided large density of docking site for probe DNA immobilization and increased the electrical conductivity ability of the electrode. The modification procedure was monitored by electrochemical impedance spectroscopy (EIS). Square-wave voltammetry (SWV) was used to explore the hybridization events. Under the optimal conditions, the designed electrochemical DNA biosensor could effectively distinguish different mismatch degrees of complementary DNA from one-base mismatch to noncomplementary, indicating that the biosensor had high selectivity. It also exhibited a reasonable linear relationship. The oxidation peak currents of [Cu(phen)₂]²⁺ were linear with the logarithm of the concentrations of complementary target DNA ranging from 1 × 10⁻¹² to 1 × 10⁻⁶ M with a detection limit of 1.99 × 10⁻¹³ M (signal/noise = 3). Moreover, the stability of the electrochemical DNA biosensor was also studied.     

Ultrasensitive DNA sensor based on gold nanoparticles/reduced graphene oxide/glassy carbon electrode

We have designed a simple and novel electrochemical biosensor based on glassy carbon electrode (GCE) for DNA detection. GCE was modified with reduced graphene oxide (RGO) and gold nanoparticles (AuNPs) by the electrochemical method, which is helpful for immobilization of thiolated bioreceptors. The electrode modification processes were characterized by scanning electron microscopy (SEM) and electrochemical methods. Then a single-stranded DNA (ssDNA) probe for BRCA1 5382 insC mutation detection was immobilized on the modified electrode for a specific time. The experimental conditions, such as probe immobilization time and target DNA (complementary DNA) hybridization time and temperature with probe DNA, were optimized using electrochemical methods. The electrochemical response for DNA hybridization and synthesis was measured using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) methods. The calibration graph contains two linear ranges; the first part is in the range of 3.0 × 10⁻²⁰ to 1.0 × 10⁻¹² M, and the second segment part is in the range of 1.0 × 10⁻¹² to 1.0 × 10⁻⁷ M. The biosensor showed excellent selectivity for the detection of the complementary sequences from noncomplementary sequences, so it can be used for detection of breast cancer.     

Synthesis, characterization and reactivity of polypyridyl ruthenium(II) carbonyl complexes with phosphine derivatives: Ruthenium-carbon bond labilization based on steric and electronic effects

Ruthenium phosphine complexes with a CO ligand [Ru(tpy)(PR₃)(CO)Cl]⁺ (tpy = 2,2′:6′,2″-terpyridine, R = Ph or p-tolyl), were prepared by introduction of CO gas to the corresponding dichloro complexes at room temperature. New carbonyl complexes were characterized by various methods including structural analyses. They were shown to release CO following the addition of several N-donors to form the corresponding substituted complexes. The kinetic data and structural results observed in this study indicated that the CO release reactions proceeded in an interchange mechanism. The molecular structures of [Ru(tpy)(PPh₃)(CO)Cl]PF₆, [Ru(tpy)(P(p-tolyl)₃)(CO)Cl]PF₆ and [Ru(tpy)(PPh₃)(CH₃CN)Cl]PF₆ were determined by X-ray crystallography.     

Au-nanoclusters incorporated 3-amino-5-mercapto-1,2,4-triazole film modified electrode for the simultaneous determination of ascorbic acid, dopamine, uric acid and nitrite

A novel biosensor has been constructed by the electrodeposition of Au-nanoclusters (nano-Au) on poly(3-amino-5-mercapto-1,2,4-triazole) (p-TA) film modified glassy carbon electrode (GCE) and employed for the simultaneous determination of dopamine (DA), ascorbic acid (AA), uric acid (UA) and nitrite (NO₂⁻). NH₂ and SH groups exposed to the p-TA layer are helpful for the electrodeposition of nano-Au. The combination of nano-Au and p-TA endow the biosensor with large surface area, good biological compatibility, electricity and stability, high selectivity and sensitivity and flexible and controllable electrodeposition process. In the fourfold co-existence system, the linear calibration plots for AA, DA, UA and NO₂⁻ were obtained over the range of 2.1–50.1 μM, 0.6–340.0 μM, 1.6–110.0 μM and 15.9–277.0 μM with detection limits of 1.1 × 10⁻⁶ M, 5.0 × 10⁻⁸ M, 8.0 × 10⁻⁸ M and 8.9 × 10⁻⁷ M, respectively. In addition, the modified biosensor was applied to the determination of AA, DA, UA and NO₂⁻ in urine and serum samples by using standard adding method with satisfactory results.     

Enhanced DNA photocleavage properties of Ru(II) terpyridine complexes upon incorporation of methylphenyl substituted terpyridine and/or the polyazine bridging ligand dpp (2,3-bis(2-pyridyl)pyrazine)

The heteroleptic complexes, [(MePhtpy)RuCl(dpp)](PF₆) and [(tpy)RuCl(dpp)](PF₆), have been synthesized, characterized, and investigated with respect to their photophysical, redox, and DNA photocleavage properties (where MePhtpy = 4′-(4-methylphenyl)-2,2′:6′,2′′-terpyridine and dpp = 2,3-bis(2-pyridyl)pyrazine, tpy = 2,2′:6′,2′′-terpyridine). The X-ray crystal structure confirms the identity of the new [(MePhtpy)RuCl(dpp)](PF₆) complex. These heteroleptic complexes were found to photocleave DNA in the presence of oxygen, unlike the previously studied complex, [Ru(tpy)₂](PF₆)₂. The photophysical, redox, and DNA photocleavage properties of the heteroleptic complexes were compared with those of the homoleptic complexes, [Ru(MePhtpy)₂](PF₆)₂ and [Ru(tpy)₂](PF₆)₂. The heteroleptic complexes showed intense metal to ligand charge transfer (MLCT) transition at lower energy ([(MePhtpy)RuCl(dpp)](PF₆), 522 nm; [(tpy)RuCl(dpp)](PF₆), 516 nm) and longer excited state lifetimes as compared to the homoleptic complexes. The [Ru(MePhtpy)₂]²⁺ complex was found to photocleave DNA in contrast to [Ru(tpy)₂]²⁺. The introduction of a methylphenyl group on the tepyridine ligand not only enhances the ³MLCT excited state lifetime but also increases the lipophilicity and thereby the DNA binding ability of the molecule. An increase in lipophilicity upon addition of a methylphenyl group on the 2,2′:6′,2′′-terpyridine ligand was confirmed by determination of the partition coefficient ([(MePhtpy)RuCl(dpp)](PF₆), log P = +1.16; [(tpy)RuCl(dpp)](PF₆), log P = −1.27). The heteroleptic complexes photocleave DNA more efficiently than the homoleptic complexes, with the greatest activity being observed for the newly prepared [(MePhtpy)RuCl(dpp)](PF₆) complex.     

Interfacial electron transfer on TiO2 sensitized with an axially anchored trans tetradentate Ru(II) compound

The ruthenium complexes, trans-[Ru(phen-NH-phen)(eina)₂](PF₆)₂ and trans-[Ru(phen-NH-phen)(ina)₂](PF₆)₂ where phen-NH-phen = N,N-bis(1,10-phenanthroline-2-yl)amine, ina = isonicotinic acid and eina = ethyl isonicotinate, have been synthesized and characterized by ¹H NMR, elemental analysis, and IR spectroscopy. The compounds were non-emissive at room temperature, but displayed intense photoluminescence in 4:1 ethanol/methanol glasses at 77 K with corrected emission maximum at 570-580 nm. A quasi-reversible wave observed in cyclic voltammetry experiments was assigned to the Ru^III/II couple, E° (trans-[Ru(phen-NH-phen)(eina)₂)^3+/2+ = +1.22 V versus Ag/AgCl. The trans-[Ru(phen-NH-phen)(ina)₂](PF₆)₂ compound was found to bind to nanocrystalline TiO₂ thin films from acetonitrile solution. Pulsed 532 nm excitation of trans-[Ru(phen-NH-phen)(ina)₂](PF₆)₂ anchored to mesoporous nanocrystalline TiO₂ thin films resulted in an absorption difference spectra consistent with the formation of an interfacial charge separated state trans-[Ru^III (phen-NH-phen)(ina)₂]⁺/TiO₂ (e⁻). The formation of this state could not be time resolved, consistent with rapid excited state injection into the TiO₂, k_inj > 10⁸ s⁻¹. Comparative measurements with a thin film actinometer yielded an injection quantum yield (?_inj) of 0.8. Charge recombination required milliseconds for completion and followed a bi-second-order equal concentration kinetic model with k₁ = 1.0 × 10⁸ s⁻¹, and k₂ = 3.0 × 10⁵ s⁻¹. In regenerative solar cells with 0.5 M LiI and 0.005 M I₂ in acetonitrile, incident photon-to-current efficiencies were typically less than 10%.     

Hydrogen bonding: further evidence for the cause of the color change of nitrosylpentaamminechromium (III) compounds. Crystal structures of [Cr(NO)(NH3)5](PF6)2 and [Cr(NO)(NH3)5]Cl(PF6)

The crystal structures of [Cr(NO)(NH₃)₅](PF₆)₂ (red) and [Cr(NO)(NH₃)₅]Cl(PF₆) (brown) have been determined. The [Cr(NO)(NH₃)₅]²⁺(A) complex cations in these compounds have a slightly distorted octahedral geometry with a strictly linear Cr-N-O arrangement (from symmetry). The short interatomic distances (2.399 Å × 4) between the O (nitrosyl) and H (ammonia in adjacent complex cations) atoms in A(PF₆)₂ indicate the existence of hydrogen bonds, while the interatomic distances (3.258 Å × 8) between those in ACl(PF₆) are much longer, and the hydrogen bonds should be weak in spite of the presence of the smaller counter anion of chloride ion in ACl(PF₆). Comparisons of the five crystal structures of A(PF₆)₂, ACl₂, ACl(ClO₄), ACl(PF₆), and A(ClO₄)₂ have led to the conclusion that the existence of the strong hydrogen bonds gives red crystals of A(PF₆)₂, while the absence of hydrogen bonds results in the formation of green crystals of A(ClO₄)₂ (O ? H, 3.595 Å × 2). The color change of the crystals (from red to green) with the change of outer sphere anions is attributed to the change of the strength of the hydrogen bonding between the complex cations.     

Reactions of pentaammineruthenium complexes with 1,2- and 1,4-dicyanobenzene and cyanobenzamides: evidences of neighboring group participation

The spectral (UV-Vis and IR) and electrochemical behavior of the nitrile bonded complexes [Ru(NH₃)₅L]²⁺ (L = 1,4-dicyanobenzene (1,4-dcb), 1,2-dicyanobenzene (1,2-dcb)), [Ru(NH₃)₅(NHC(OH)-bz-4-CN)]³⁺, [Ru(NH₃)₅(NHC(O)-bz-2-CN)]²⁺ and [Ru(NH₃)₅(NH(C)NHC(O)bz)]³⁺ (NH(C)NHC(O)-bz = 3-imino-1-oxo-isoindoline) are described. Oxidation of [Ru(NH₃)₅L]²⁺, at 0 ? pH ? 6, is followed by hydrolysis of the coordinated nitrile to give amide complexes in which the amide is through the nitrogen, with pH-dependent rate constants. The estimated values of the rate constant of hydrolysis (k_obs) at 25 °C are 2.9 × 10⁻³ s⁻¹ for [Ru(NH₃)₅(1,4-dcb)]³⁺ and 5.6 × 10⁻³ s⁻¹ for [Ru(NH₃)₅(1,2-dcb)]³⁺ at pH 4.65. Reduction of [Ru(NH₃)₅(NHC(O)-bz-4-CN)]²⁺ and [Ru(NH₃)₅(NHC(O)-bz-2-CN)]²⁺ is followed by two reactions, one is an aquation forming [Ru(NH₃)₅(OH₂)]²⁺ and free ligand, and the other an intramolecular linkage isomerization forming [Ru(NH₃)₅(NC-bz-4-NH₂C(O))]²⁺ and [Ru(NH₃)₅(NC-bz-2-NH₂C(O))]²⁺. The oxidized1,2-cyanobenzamide complex [Ru(NH₃)₅(NHC(OH)-bz-2-CN)]³⁺ undergoes an amide to nitrile intramolecular linkage isomerization, followed by a cyclization reaction resulting in [Ru(NH₃)₅(NH-(C)(HN-C(O)-2-bz))]³⁺ ((NH-(C)(HN-C(O)-2-bz)) = 3-imino-1-oxo-isoindoline bonded through the exocyclic nitrogen) (pK_a = 4.3). The rates of these reactions, which occur with neighboring group participation, increase with acidity. The reduced form, [Ru(NH₃)₅(NH-(C)(HN-C(O)-2-bz))]²⁺, is relatively substitution inert.     

Study of interactions between DNA and aflatoxin B1 using electrochemical and fluorescence methods

In this study, a carbon paste electrode modified with N-butylpyridinium hexafluorophosphate (BPPF₆) ionic liquid and DNA was introduced as an electrochemical biosensor to study the interaction between DNA and aflatoxin B1 molecules. For this purpose, variations in oxidation peak current of guanine in various concentrations of aflatoxin B1 were measured by using the differential pulse voltammetry (DPV) method. According to this study, the binding constant of DNA–aflatoxin B1 was found to be 3.5 × 10⁶ M⁻¹. This modified electrode was also used for determination of low concentrations of aflatoxin B1 by using differential pulse voltammetry. A linear dynamic range from 8.00 × 10⁻⁸ to 5.91 × 10⁻⁷ M and a limit of detection of 2.00 × 10⁻⁸ M resulted from DPV measurements. To confirm our results, a fluorescence study was also performed. It resulted in a binding constant of 2.8 × 10⁶ M⁻¹, which is in good agreement with that obtained from electrochemical study.     

Electrochemical synthesis of gold nanostructure modified electrode and its development in electrochemical DNA biosensor

In this article, gold nanostructure modified electrodes were achieved by a simple one-step electrodeposition method. The morphologies of modified electrodes could be easily controlled by changing the pH of HAuCl₄ solution. The novel nanoflower-like particles with the nanoplates as the building blocks could be interestingly obtained at pH 5.0. The gold nanoflower modified electrodes were then used for the fabrication of electrochemical DNA biosensor. The DNA biosensor fabrication process was characterized by cyclic voltammetry and electrochemical impedance spectroscopy with the use of ferricyanide as an electrochemical redox indicator. The DNA immobilization and hybridization on gold nanoflower modified electrode was studied with the use of [Ru(NH₃)₆]³⁺ as a hybridization indicator. The electrochemical DNA biosensor shows a good selectivity and sensitivity toward the detection of target DNA. A detection limit of 1 pM toward target DNA could be obtained.     

Synthesis, characterization, photophysics and intramolecular energy transfer process in bimetallic rhenium(I)-ruthenium(II) complexes

Two new heterobimetallic complexes of rhenium(I) and ruthenium(II) [(CO)₃(NN)Re(4,4′-bpy)Ru(NN)₂Cl](PF₆)₂ and already known monometallic complexes [Cl(NN)₂Ru(4,4′-bpy)](PF₆) and [(CO)₃(NN)Re(4,4′-bpy)](PF₆) and bimetallic complexes [Cl(NN)₂Ru(4,4′-bpy)Ru(NN)₂Cl](PF₆)₂, [(CO)₃(NN)Re(4,4′-bpy)Re(NN)(CO)₃](PF₆)₂ (NN = 2,2′-bipyridine, 1,10-phenanthroline; 4,4′-bpy = 4,4′-bipyridine) are synthesized and characterized by spectral techniques. The photophysical properties of all the complexes are studied. It is found that attachment of rhenium(I) altered the photophysical characteristics of ruthenium(II). Excited state energy transfer from the rhenium(I) chromophore to the ruthenium(II) is observed upon excitation at 355 nm.     

Assisted self-association of dicyanoaurate, [Au(CN)2], and dicyanoargentate, [Ag(CN)2], through hydrogen bonding to metal ammonia complexes

The salts - yellow [Cr(NH₃)₆][Ag(CN)₂]₃ · 2H₂O, red [Co(NH₃)₆][Ag(CN)₂]₃ · 2H₂O, red [Co(NH₃)₆][Au(CN)₂]₃ · 2H₂O, pale yellow [Ru(NH₃)₆][Ag(CN)₂]₃ · 2H₂O, yellow K[Cr(NH₃)₆]₂[Au(CN)₂]₇ · 4H₂O, and colorless [(μ²-NH₂)₂Pt₂(NH₃)₁₀][Au(CN)₂]₆ · 5.5{OS(CH₃)₂} · 0.5H₂O - have been prepared by evaporation of aqueous solutions of potassium dicyanoargenate or potassium dicyanoaurate and salts of the appropriate cations. Hydrogen bonding between the cations and the cyano groups of the anions facilitates the formation of structures with strong metallophilic interactions between the anions. Thus, the [Au(CN)₂]⁻ or [Ag(CN)₂]⁻ ions self-associate into linear trimers in the isostructural set of crystals, [Cr(NH₃)₆][Ag(CN)₂]₃ · 2H₂O (Ag?Ag distance; 3.1610(4) Å), [Co(NH₃)₆][Ag(CN)₂]₃ · 2H₂O (Ag?Ag distance; 3.1557(2) Å), [Co(NH₃)₆][Au(CN)₂]₃ · 2H₂O (Au?Au distance; 3.0939(4) Å), and [Ru(NH₃)₆][Ag(CN)₂]₃ · 2H₂O (Ag?Ag distance; 3.1584(5) Å). Crystalline [(μ²-NH₂)₂Pt₂(NH₃)₁₀][Au(CN)₂]₆ · 5.5{OS(CH₃)₂} · 0.5H₂O also contains nearly linear trimers of the dicyanoaurate ion. Yellow crystals of K[Cr(NH₃)₆]₂[Au(CN)₂]₇ · 4H₂O contain a centrosymmetric, bent chain of seven dicyanoaurate ions with Au?Au separations of 3.1806(3), 3.2584(4), and 3.1294(4) Å.     

DNA interaction studies of tridentate bridged Ru(II)-Pt(II) mixed-metal supramolecules

Reported herein are studies of the concentration and temperature dependent interactions with DNA of the stereochemically defined mixed-metal supramolecular complexes, [(tpy)Ru(tppz)PtCl](PF₆)₃ and [ClPt(tppz)Ru(tppz)PtCl](PF₆)₄ (tpy = 2,2′:6′,2′′-terpyridine and tppz = 2,3,5,6-tetrakis(2-pyridyl)pyrazine). These metal complexes couple a ruthenium based light absorber (LA) to the bioactive platinum sites (BAS) using a tridentate bridging ligand (BL). The complexes exhibit intense Ru → tppz(π∗) metal to ligand charge transfer (MLCT) transitions in the visible region and adopt a square planar geometry around the Pt(II) center. The effect of incubating these metal complexes with DNA on the subsequent migration of DNA through an agarose gel was found to be more dramatic than that observed for the well known anticancer drug, cis-[Pt(NH₃)₂Cl₂] (cisplatin). This effect was enhanced with increased incubation temperature. Unwinding of supercoiled plasmid DNA was found to be more pronounced for the trimetallic complex, [ClPt(tppz)Ru(tppz)PtCl](PF₆)₄, than for the bimetallic complex, [(tpy)Ru(tppz)PtCl](PF₆)₃.     

Monitoring of <Emphasis Type="Italic">E. coli</Emphasis> immobilization on modified gold electrode: A new bacteria-based glucose sensor

Electrochemical impedance spectroscopy (EIS) technique has proved to be an effective method for monitoring the immobilization of various bioactive species such as enzymes, DNA, whole cells, and so forth. In this work we describe the development of an electrochemical whole cell based biosensor. Biotinylated fluorescent E. coli are immobilized onto a cysteamine, Sulfo-NHS-LC-biotin, and avidin modified gold electrodes. Immobilized bacteria are clearly observed using confocal microscopy. Electrochemical measurements are based on the charge-transfer kinetics of [Fe (CN)₆]^3−/4− redox couple. The experimental impedance data were modelised with a computer. SAM assembly and the subsequent immobilization of bacteria on the gold bare electrodes greatly increased the electrontransfer resistance (R _et ) and reduced the constant phase element (CPE). It’s interesting to note, the hard immobilization of bacteria on the surface of electrode and do not remove during measurements. The effect of glucose addition was studied in the range of 10⁻⁷ μM to 10 μM. The relation between the evolution of R _et and D-glucose concentration was found to be linear for values ranging from 10⁻⁵ μM to 10⁻¹ μM and reached saturation for higher concentrations. Such biosensor could be applied to a more fundamental study of cell metabolism and drugs effect.     

Syntheses and electrochemical properties of ruthenium(II) complexes with 4,4-bipyrimidine and 4,4-bipyrimidinium ligands

The syntheses and electrochemical properties of novel ruthenium(II) polypyridyl complexes with 4,4^′-bipyrimidine, [Ru(trpy)(bpm)Cl](X) ([1](X; X=PF₆⁻, BF₄⁻)) and with a quaternized 4,4^′-bipyrimidinium ligand, [Ru(trpy)(Me₂bpm)Cl](BF₄)₃ ([2](BF₄)₃) (trpy=2,2^′:6^′,2″-terpyridine, bpm=4,4^′-bipyrimidine, Me₂bpm=1,1^′-dimethyl-4,4^′-bipyrimidinium) are presented. The bpm complex [1]⁺ was prepared by the reaction of Ru(trpy)Cl₃ with 4,4^′-bipyrimidine in EtOH/H₂O. The structural characterization of [1]⁺ revealed, that the bpm ligand coordinated to the ruthenium atom with the bidentate fashion. Diquaternization of the non-coordinating nitrogen atoms on bpm of [1]⁺ by (CH₃)₃OBF₄ in CH₃CN gave [2](BF₄)₃. The electrochemical and spectroelectrochemical properties of the complexes are described.     

The bimolecular sensitization of nitric oxide release from weak interacting ruthenium units

This work reports on the bimolecular sensitization of nitric oxide release from cis-[Ru(bpy)₂(iso)NO](PF₆)₃ (1) (iso = isoquinoline and bpy = 2,2′-bipyridine) by irradiating the MLCT transition of the chloro analog cis-[Ru(bpy)₂(iso)Cl]PF₆ (2)_. The compounds displayed peaks in the ESI-MS spectra at m/z 749.1 and m/z 578.1 ascribed, respectively, to ([1(NO⁰)−2PF₆·CH₃OH]²⁺) and ([2−PF₆]⁺). In the cyclic voltammograms, the nitrosyl complex presented two redox waves related to the NO ligand at 0.48 and −0.37 V (versus Ag/AgCl, NO^+/0/−1 processes), while the sensitizer showed two reversible waves at 0.79 and −1.46 V (versus Ag/AgCl, Ru^2+/3+ and bpy ^0/−1, respectively). The most important feature of this system is that the nitrosyl compound does not have significant absorption in the visible region, while the sensitizer has an intense band centered at 496 nm. The irradiation of an equimolar mixture of the two compounds in an ethanol:water solution (v:v) with light of λ > 500 nm leads to NO release, as probed by amperometric measurements. The variational method was applied, showing that the two compounds self-assembly in solution with a 1:1 stoichiometry. Fluorescence spectra acquired at 77 K provided the E_0-0 for the system and, from the thermodynamic cycle it was estimated that the photoinduced electron transfer between the species has a ΔG value of −1.59 eV.     

Metal-metal stacking patterns between and with [Pt(tpy)X] cations

A comparative study of metallophilic interactions of [Pt(tpy)X]⁺ cations (tpy = 2,2′:6′,2″-terpyridine) in the presence of two different types of anions, (i) []⁻ anions that form double salts and (ii) simple p-block anions, is reported. Single-crystal X-ray diffraction data, solution-state ¹⁹⁵Pt NMR spectra, and variable temperature solid-state luminescence spectra are reported. Three [Pt(tpy)Cl]Y derivatives (Y = SbF₆, 1, SbF₆·CH₃CN, 4, PF₆, 2) and the [Pt(tpy)Br]PF₆ analog, 3, as well as two new double salts [Pt(tpy)CN][Au(CN)₂], 5, and [Pt(tpy)CN]₂[Au(C₆F₅)₂](PF₆), 6, have been synthesized and characterized. Structural analysis shows consistent patterns in Pt···Pt interactions that vary slightly depending on the coordinating halogen or pseudo-halogen X, counter anion Y, and lattice solvent. Metallophilic interactions are seen between [Pt(tpy)X]⁺ cations with all types of X ligands, but only with π-accepting X′ ligands from []⁻ anions are Pt?Au metallophilic interactions seen to be favored over Pt?Pt interactions. The [Au(CN)₂]⁻ anion consistently forms Pt···Au metallophilic contacts, unlike [Au(C₆F₅)₂]⁻. The ¹⁹⁵Pt NMR chemical shifts are ∼−2750 ppm for π-donor ligands and near −3120 ppm for π-acceptor ligands in [Pt(tpy)X]PF₆ compounds. Luminescence data show an unusual blue shift in [Pt(tpy)CCPh][Au(C₆F₅)₂] versus [Pt(tpy)CCPh]PF₆ ascribed to an intermolecular charge transfer.     

Synthesis, characterization and DNA interactions of 5,15-(4-pyridyl)-10,20-(pentafluorophenyl)porphyrin coordinated to two [Ru(bipy)2Cl] groups

A new porphyrin 5,15-(4-pyridyl)-10,20-(pentafluorophenyl)porphyrin (H₂DPDPFPP) and its diruthenium(II) analog ([trans-H₂(DPDPFPP)Ru₂(bipy)₄Cl₂(PF₆)₂]) have been synthesized and characterized. Electronic transitions associated with the porphyrin consist of an intense Soret band near 400 nm and four Q-bands from 500 nm to 650 nm. Coordination of two [Ru(bipy)₂Cl]⁺ groups, where bipy = 2,2′-bipyridine, to the pyridyl nitrogens of the porphyrin give additional electronic transitions associated with the bipy orbitals and metal to ligand charge transfer (MLCT) transitions associated with the Ru(II) and bipy orbitals. Reversible redox couples in the cathodic region occur at E_1/2 = −0.74 V and −1.21 V versus Ag/AgCl reference which are shifted to more positive potentials when the porphyrin is coordinated to the Ru(II) groups. Gel electrophoresis studies with linearized pUC18 indicate an interaction between the metallated porphyrin and DNA which is confirmed by UV/Vis titrations with calf thymus (CT) DNA giving a binding constant of ca. 10⁵ M⁻¹. When buffered, pH 7, solutions of circular plasmid DNA containing the ruthenium porphyrin are irradiated with a 50 W tungsten lamp cleavage of the DNA is observed.     

Fluorescein-labeled “arch-like” DNA probes for electrochemical detection of DNA on gold nanoparticle-modified gold electrodes

In the present study, a gold nanoparticle-modified gold electrode (nanogold electrode) was used to develop a novel fluorescein electrochemical DNA biosensor based on a target-induced conformational change. The nanogold electrode was obtained by electrodepositing gold nanoparticles onto a bare gold electrode. This modification not only immobilized probe oligonucleotides, but also adsorbed fluorescein onto the surface of the gold nanoparticles to form an “arch-like” structure. This article compares the electrochemical signal changes caused by the hybridization of “arch-like” DNA on nanogold electrode and linear DNA on bare gold electrode. The results showed that the adsorption effect of nanogold can enhance the sensitivity of the sensor. The linear range of target ssDNA is from 2.0 × 10⁻⁹ M to 2.0 × 10⁻⁸ M with a correlation coefficient of 0.9956 and detection limit (3σ) of 7.10 × 10⁻¹⁰ M. Additionally, the specificity and hybridization response of this simple sensor were investigated.