Preparation of highly efficient monolithic silica capillary columns for the separations in weak cation-exchange and HILIC modes

Weak cation-exchange (WCX) and HILIC modes columns were prepared by on-column polymerization of acrylic acid on monolithic silica capillary columns modified with N-(3-triethoxysilylpropyl)methacrylamide anchor groups. The polymer-coated columns could be used for HILIC mode separation of pyridylamino (PA)-sugars and peptides including a tryptic digest of BSA, while for weak cation-exchange mode for the separation of proteins and nucleosides even at high linear velocity. The poly(acrylic acid) coated monolithic silica capillary columns showed greater retention toward PA-sugars than a polyacrylamide coated monolithic silica capillary columns prepared in the same manner. Proteins and nucleosides were separated effectively at pH 6.9 using the same column. The column provided fair permeability after the polymer-coating step. High-speed separation of proteins at u=4.66 mm/s with high efficiency was shown to be possible, while high-speed separation of nucleosides has achieved within one minute using the column at u=8.67 mm/s, suggesting that the column will be suitable for the second dimension separation of multidimensional HPLC systems.     

Separation of 2-aminobenzamide labeled glycans using hydrophilic interaction chromatography columns packed with 1.7 μm sorbent

Separation by hydrophilic interaction chromatography (HILIC) with fluorescence detection utilizing a sub-2 μm glycan column for the separation of 2-aminobenzamide (2-AB) labeled N-linked glycans is described. The HILIC column packed with a 1.7 μm amide sorbent improves the peak capacity compared to a 3.0 μm HILIC column by a similar degree as observed in reversed-phase ultra-performance liquid chromatography (RP-UPLC). The results indicated that the optimal peak capacity was achieved at flow rate 0.2–0.5 mL/min. HILIC method transfer guidelines were shown to further enhance the resolution of glycans by changing initial gradient conditions, flow rate, column temperature, and different column lengths. Additionally, excellent resolution can be achieved in the separation of 2-AB labeled glycans released from fetuin, RNase B, and human IgG with a rapid analysis time.     

HPLC separation of some purine and pyrimidine derivatives on Chromolith Performance Si monolithic column

The chromatographic behavior of some purines and pyrimidines on a monolithic Chromolith Performance Si column under normal-phase high-performance liquid chromatography mode has been studied. Column pressure, column efficiency and selectivity of Chromolith Performance Si column were compared to those of conventional spherical 5 μm silica packed columns Econosphere Silica and Zorbax Rx-SIL. The investigation has shown that application of Chromolith Performance Si column for analysis of polar solutes can reduce the separation time without sacrificing column efficiency and selectivity. Improvement of the monolithic silica column efficiency for polar solutes is observed when ternary mobile phases (mixtures of hexane–isopropanol with ethylene glycol, water or acetonitrile) are applied.     

Determination of metoclopramide in human plasma using hydrophilic interaction chromatography with tandem mass spectrometry

For the rapid, selective and sensitive analysis of metoclopramide in human plasma, hydrophilic interaction chromatography with electrospray ionization tandem mass spectrometric (HILIC/MS/MS) method was developed. This method involved liquid–liquid extraction with dichloromethane followed by separation on an Atlantis HILIC silica column using the mobile phase of acetonitrile–ammonium formate (100 mM, pH 6.5) (85:15, v/v). Analytes were quantified using electrospray ionization mass spectrometry in the selected reaction monitoring mode. The standard curve was linear (r² = 0.998) over the concentration range of 2.00–150 ng/mL using 50 μL of plasma sample. The coefficient of variation and relative error for intra- and inter-assay at four QC levels were 1.8–7.7% and ?7.5 to 3.6%, respectively. The matrix effect for metoclopramide and levosulpiride (internal standard) was practically absent. The present method was successfully applied to the pharmacokinetic study of metoclopramide after oral dose of metoclopramide hydrochloride (10 mg) to male healthy volunteers.     

Optimization of single-column chromatographic separation of fructooligosaccharides

An experimental study aimed at the design and optimization of single-column separation of fructooligosaccharides from mono- and disaccharides was carried out. Amberlite™ CR1320Ca, a cation-exchange resin with a calcium ion as the functional group was packed in two laboratory columns of different dimensions. Optimization parameters were the superficial velocity and the column load. In a smaller column, the maximal yield of fructooligosaccharides of 86% and the selectivity of separation of 82% were achieved for the column load of 2.0% and superficial velocity of 5.0 × 10⁻⁵ m s⁻¹. At the same process conditions in a larger column, the yield and selectivity increased to 90%.     

Capillary electrophoresis of chitooligosaccharides in acidic solution: Simple determination using a quaternary-ammonium-modified column and indirect photometric detection with Crystal Violet

Five chitosan oligosaccharides were separated in acidic aqueous solution by capillary electrophoresis (CE) with indirect photometric detection using a positively coated capillary. Electrophoretic mobility of the chitooligosaccharides (COSs) depended on the number of monomer units in acidic aqueous solution, similar to other polyelectrolyte oligomers. The separation was developed in nitric acid aqueous solution at pH 3.0 with 1 mM Crystal Violet, using a capillary positively coated with N-trimethoxypropyl-N,N,N-trimethylammonium chloride. The limit of the detection for chitooligosaccharides with two to six saccharide chains was less than 5 μM. CE determination of an enzymatically hydrolyzed COS agreed with results from HPLC.     

Using short columns to speed up LC–MS quantification in MS binding assays

The present study describes the use of short columns to speed up LC–MS quantification in MS binding assays. The concept of MS binding assays follows closely the principle of traditional radioligand binding but uses MS for the quantification of bound marker thus eliminating the need for a radiolabelled ligand. The general strategy of increasing the throughput of this type of binding assay by the use of short columns is exemplified for NO 711 binding addressing GAT1, the most prevalent GABA transporter in the CNS. Employing short RP-18 columns with the dimension of 20 mm × 2 mm and 10 mm × 2 mm at flow rates up to 1000 μL/min in an isocratic mode retention times of 8–9 s and chromatographic cycle times of 18 s could be achieved. Based on the internal standard [²H₁₀]NO 711 fast chromatography methods were developed for four different columns that enabled quantification of NO 711 in a range from 50 pM up to 5 nM directly out of reconstituted matrix samples without further sample preparation. A validation of the established methods with respect to linearity, intra- and inter-batch accuracy and precision showed that the requirements according to the FDA guideline for bioanalytical methods are met. Furthermore the established short column methods were applied to the quantification of NO 711 in saturation experiments. The results obtained (i.e., K_d- and B_max-values) were almost identical as compared to those determined employing standard column dimension (55 mm × 2 mm).     

Automated metal-free multiple-column nanoLC for improved phosphopeptide analysis sensitivity and throughput

We report on the development and characterization of automated metal-free multiple-column nanoLC instrumentation for sensitive and high-throughput analysis of phosphopeptides with mass spectrometry. The system employs a multiple-column capillary LC fluidic design developed for high-throughput analysis of peptides (Anal. Chem. 2001, 73, 3011–3021), incorporating modifications to achieve broad and sensitive analysis of phosphopeptides. The integrated nanoLC columns (50 μm i.d. × 30 cm containing 5 μm C18 particles) and the on-line solid phase extraction columns (150 μm i.d. × 4 cm containing 5 μm C18 particles) were connected to automatic switching valves with non-metal chromatographic accessories, and other modifications to avoid the exposure of the analyte to any metal surfaces during handling, separation, and electrospray ionization. The nanoLC developed provided a separation peak capacity of ～250 for phosphopeptides (and ～400 for normal peptides). A detection limit of 0.4 fmol was obtained when a linear ion trap tandem mass spectrometer (Finnegan LTQ) was coupled to a 50-μm i.d. column of the nanoLC. The separation power and sensitivity provided by the nanoLC–LTQ enabled identification of ～4600 phosphopeptide candidates from ～60 μg COS-7 cell tryptic digest followed by IMAC enrichment and ～520 tyrosine phosphopeptides from ～2 mg of human T cells digests followed by phosphotyrosine peptide immunoprecipitation.     

Separation and determination of Se-compounds by liquid chromatography coupled with electrospray mass spectrometry

A method for Selenocystine and Selenomethionine determination by LC–ES–MS was developed in this work. The mass spectrometer was used in a positive mode and the m/z used for the identification of Selenomethionine and Selenocystine were 198.35 and 337.15, respectively.The selenium species were separated using a LC system. A silica chromatographic column (ZORBAX Eclipse XDB-C₈ of 50 mm length and 2.1 mm internal diameter (particle size 3.5 μm)) was used. The separation was realised in isocratic mode, using methanol:water (1:1) with 1% of acetic acid and a flow rate of 200 μL min⁻¹. The developed method was precise (RSD of 4.5% and 3.9% for Selenomethionine and Selenocystine, respectively) and sensible (limit of detection (LOD) 0.06 and 0.99 mg L⁻¹ for selenomethionine and selenocystine, respectively).     

Optimisation of preparative HPLC separation of four isomeric kaempferol diglycosides from Prunus spinosa L. by application of the response surface methodology

A fast and efficient preparative HPLC-PDA method was developed for the separation and isolation of four rare isomeric kaempferol diglycosides from leaves of Prunus spinosa L. The separation procedure of the enriched diglycoside fraction of the 70% (v/v) aqueous methanolic leaf extract was first optimised on analytical XBridge C18 column (100 mm × 4.6 mm i.d., 5 μm) and central composite design combined with response surface methodology was utilized to establish the optimal separation conditions. The developed method was directly transferred to preparative XBridge Prep C18 column (100 mm × 19 mm i.d., 5 μm) and the final separation was accomplished by isocratic elution with 0.5% acetic acid-methanol-tetrahydrofuran (75.2:16.6:8.2, v/v/v) as the mobile phase, at a flow rate of 13.6 mL/min, in less than 12 min for a single run. Under these conditions, four flavonoid diglycosides: kaempferol 3-O-α-l-arabinofuranoside-7-O-α-l-rhamnopyranoside, kaempferol 3,7-di-O-α-l-rhamnopyranoside (kaempferitrin), and reported for the first time for P. spinosa kaempferol 3-O-β-d-xylopyranoside-7-O-α-l-rhamnopyranoside (lepidoside) and kaempferol 3-O-α-l-arabinopyranoside-7-O-α-l-rhamnopyranoside, were isolated in high separation yield (84.8–94.5%) and purity (92.45–99.79%). Their structures were confirmed by extensive 1D and 2D NMR studies. Additionally, the UHPLC-PDA-ESI–MS³ qualitative profiling led to the identification of twenty-one phenolic compounds and confirmed that the isolates were the major components of the leaf material.     

One-step purification of YLLIP2 isoforms from Candida sp. 99–125 by polyethyleneimine modified poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate) monolith

The extracellular lipase Yarrowia lipolytica (YLLIP2) crude extract was efficiently separated and purified from Candida sp. 99–125 by one-step ion-exchange chromatography on polyethyleneimine (PEI) functionalized monolithic columns. The preparative conditions for the functionalization of monoliths were optimized, including PEI molecular mass, PEI concentration, modification time and temperature. The monolithic skeleton was prepared in situ by polymerization of glycidyl methacrylate (GMA) and ethylene glycol dimethacrylate (EGDMA) with a volume ratio of 8:2. Heptane was used as the porogen. PEI 30 kDa with the concentration of 10% (v/v) was applied for the modification of the monolith at 55 °C for 12 h. Lipase (EC.3.1.1.3) from Candida sp. 99–125 was separated to four isoforms (isoform A, isoform B, isoform C and isoform D). As analyzed on non-denaturing PAGE and MALDI-TOF–MS, the four isoforms are homogenous and have the same molecular mass of approximate 38 kDa. The monoliths can afford direct crude lipase loading without increasing too much back pressure, which explores the great potential of the application of monoliths for one-single step fast separation and purification of complicated proteins.     

The relationship between interleukin-6 in saliva,venous and capillary plasma,at rest and in response to exercise

IL-6 plays a mechanistic role in conditions such as metabolic syndrome, chronic fatigue syndrome and clinical depression and also plays a major role in inflammatory and immune responses to exercise. The purpose of this study was to investigate the levels of resting and post exercise IL-6 when measured in venous plasma, saliva and capillary plasma. Five male and five females completed 2 separate exercise trials, both of which involved standardized exercise sessions on a cycle ergometer. Venous blood and saliva samples were taken immediately before and after Trial A, venous and capillary blood samples were taken immediately before and after Trial B. IL-6 values were obtained using a high-sensitivity enzyme-linked immunosorbent assay (ELISA). In Trial A venous plasma IL-6 increased significantly from 0.4 ± 0.14 pg/ml to 0.99 ± 0.29 pg/ml (P < 0.01) while there was no increase in salivary IL-6. Venous plasma and salivary IL-6 responses were not correlated at rest, post exercise or when expressed as an exercise induced change. In Trial B venous and capillary plasma IL-6 increased significantly (venous: 0.22 ± 0.18 to 0.74 ± 0.28 pg/ml (P ⩽ 0.01); capillary: 0.37 ± 0.22 to 1.08 ± 0.30 pg/ml (P < 0.01). Venous and capillary plasma responses did not correlate at rest (r = 0.59, P = 0.07) but did correlate post exercise (r = 0.79, P ⩾ 0.001) and when expressed as an exercise induced change (r = 0.71, P = 0.02). Saliva does not appear to reflect systemic IL-6 responses, either at rest or in response to exercise. Conversely, capillary plasma responses are reflective of systemic IL-6 responses to exercise.     

Solid-phase extraction of tanshinones from Salvia Miltiorrhiza Bunge using ionic liquid-modified silica sorbents

New ionic liquid-modified silica sorbents were developed by the surface chemical modification of the commercial silica using synthesized ionic liquids. The obtained ionic liquid-modified particles were successfully used as a special sorbent in solid-phase extraction process to isolation of cryptotanshinone, tanshinone I and tanshinone IIA from Salvia Miltiorrhiza Bunge. Different washing and elution solvents such as water, methanol and methanol–acetic acid (90/10, v/v) were evaluated. A comparison of ionic liquid-modified silica cartridges and traditional silica cartridge show that higher recovery was observed using ionic liquid-modified silica sorbents. A quantitative analysis was conducted by high-performance liquid chromatography using a C₁₈ column (5 μm, 150 mm × 4.6 mm) with methanol–water (78:22, v/v, and containing 0.5% acetic acid) as a mobile phase. Good linearity was obtained from 0.5 × 10^?4 to 0.5 mg/mL (r² > 0.999) with the relative standard deviations less than 4.8%.     

Simultaneous determination of cyclophosphamide and carboxyethylphosphoramide mustard in human plasma using online extraction and electrospray tandem mass spectrometry (HTLC–ESI-MS/MS)

A rapid and selective method for simultaneous determination of cyclophosphamide and its metabolite carboxyethylphosphoramide mustard (CEPM) was developed using online sample preparation and separation with tandem mass spectrometric detection. Diluted plasma was injected onto an extraction column (Cyclone MAX 0.5 mm × 50 mm, >30 μm), the sample matrix was washed with an aqueous solution, and retained analytes were transferred to an analytical column (Gemini 3 μm C18 110A, 100 mm × 2.0 mm) using a gradient mobile phase prior to detection by MS/MS. Analytes were detected in an API-3000 LC-MS/MS system using positive multiple-reaction monitoring mode (m/z 261/140 and 293/221 for CTX and CEPM, respectively). Online extraction recoveries were 76% and 72% for cyclophosphamide and CEPM. Within-day and between-day variabilities were <3.0%, and accuracies were between ?6.9% and 5.2%. This method has been used to measure plasma cyclophosphamide and CEPM concentrations in an ongoing Phase II study in children with newly diagnosed medulloblastoma.     

Turbulent-flow chromatography coupled on-line to fast high-performance liquid chromatography and mass spectrometry for simultaneous determination of verticine,verticinone and isoverticine in rat plasma

A method based on the on-line turbulent-flow chromatography and fast high-performance liquid chromatography/mass spectrometry (TFC–LC/MS) was developed for sensitive and high throughput pharmacokinetic study of traditional Chinese medicines (TCMs). In this method, an on-line extraction column (Waters Oasis HLB) and a fast HPLC column with sub-2 μm particle size (Agilent Zorbax StableBond-C₁₈, 4.6 mm × 50 mm, 1.8 μm) in a column-switching set-up were utilized. HLB is a reversed-phase extraction column with hydrophilic–lipophilic balanced copolymer (2.1 mm × 20 mm, 25 μm particle size), which will exhibit some turbulent-flow properties at a high-flow rate. The method combines the speed and robustness of turbulent-flow extraction and the sensitivity and separation efficiency of fast HPLC–MS to analyze multiple and trace constituents of TCMs in plasma matrix. This method was successfully applied for pharmacokinetic study of verticine, verticinone and isoverticine, the chemical markers of Fritillaria thunbergii, after oral administration of total steroidal alkaloids extract of F. thunbergii to rats. Each plasma sample was analyzed within 7 min. The method demonstrated good linearity (R > 0.999) ranged from 0.505 to 96.0 ng/mL with satisfactory accuracy and precision, and the lower limit of quantifications of verticine, verticinone and isoverticine were estimated to be 0.120, 0.595 and 0.505 ng/mL, respectively. These results indicate that the proposed method is fast, sensitive, and feasible for pharmacokinetic study of TCMs.     

Size exclusion chromatography of zein and xanthophylls: Optimization of operating parameters

Ethanol-soluble components of corn (zein and xanthophylls) were separated and purified by size exclusion chromatography. Aqueous ethanol was used as the solvent for the entire process from extraction through chromatography. The effect of operating and design parameters, such as temperature, flow rate, loading mass, loading volume, column height and diameter, on productivity and resolution of the components was studied. Using a one-variable-at-a-time (OVAT) approach with 1 cm × 60 cm columns, optimum conditions were determined to be 40 °C temperature, 0.25 mL/min flow rate, volume loading of 22 mL corn extract, mass loading at 70 g/L of corn extract. All components could be resolved with base line separation with a 240 cm column length. Column diameter did not affect separation, implying linear scalability with constant flow distribution.     

Forming nanoparticles of α-amylase and embedding them into solid surfaces

In the current work nanoparticles (NPs) of α-amylase were generated in an aqueous solution using high-intensity ultrasound, and were subsequently immobilized on polyethylene (PE) films, or polycarbonate (PC) plates, or on microscope glass slides. The α-amylase NPs coated on the solid surfaces have been characterized by ESEM, TEM, FTIR, XPS and AFM. The substrates immobilized with α-amylase were used for hydrolyzing soluble potato starch to maltose. The amount of enzyme introduced in the substrates, leaching properties, and the catalytic activity of the immobilized enzyme were compared. The catalytic activity of the amylase deposited on the three solid surfaces was compared to that of the same amount of free enzyme at different pHs and temperatures. α-Amylase coated on PE showed the best catalytic activity in all the examined parameters when compared to native amylase, especially at high temperatures. When immobilized on glass, α-amylase showed better activity than the native enzyme over all pH and temperature values studied. However, the immobilization on PC did not improve the enzyme activity at any pH and any temperature compared to the free amylase. The kinetic parameters, K_m and V_max were also calculated. The amylase coated PE showed the most favorable kinetic parameters (K_m = 5 g L⁻¹ and V_max = 5E−07 mol mL⁻¹ min⁻¹). In contrast, the anchored enzyme-PC exhibited unfavorable kinetic parameters (K_m = 16 g L⁻¹, V_max = 4.2E−07 mol mL⁻¹ min⁻¹). The corresponding values for amylase-glass were K_m = 7 g L⁻¹, V_max = 1.8E−07 mol mL⁻¹ min⁻¹, relative to those obtained for the free enzyme (K_m = 6.6 g L⁻¹, V_max = 3.3E−07 mol mL⁻¹ min⁻¹).     

Punto de corte de espesor de tejido adiposo epicárdico para predecir síndrome metabólico en población venezolana

ObjectiveTo define an echocardiographically-assessed cut-off point for epicardial adipose tissue (EAT) thickness associated to metabolic syndrome (MS) components in Venezuelan subjects.MethodsFifty-two subjects aged 20-65 years diagnosed with MS according to International Diabetes Federation criteria and 45 sex- and age-matched controls were selected. Blood glucose and plasma lipids were tested; EAT thickness and left ventricular mass were measured by echocardiography.ResultsNo significant age and sex differences were found between the two groups. Body weight, body mass index, waist circumference, and systolic and diastolic blood pressure were significantly higher (P = .0001) in the MS group. This group showed significantly higher levels of fasting blood glucose (P = .0001), total cholesterol (P = .002), LDL-C (P = .007), non-HDL-C (P = .0001), triglycerides (P = .0001), Tg-HDL-C ratio (P = .0001), and lower HDL-C levels (P = .0001) as compared to the control group. EAT thickness (P = .0001) and left ventricular mass (P = .017) were significantly higher in the MS group. The ROC curve showed an AUC of 0.852 (P = .0001) with a power of the test of 0.99. A 5-mm EAT thickness showed a sensitivity of 84.62% (95% CI: 71.9-93.1) and a specificity of 71.11% (95% CI: 55.7-83.6) for predicting MS. The odds ratio of this population for experiencing MS due to an EAT ≥ 5 mm was 8.25 (95% CI: 3.15-21.56; P = .0001).ConclusionAn EAT value ≥ 5 mm has good sensitivity and specificity for predicting MS in the Venezuelan population.     

Graft polymers of eucalyptus lignosulfonate calcium with acrylic acid: Synthesis and characterization

The graft copolymerization of eucalyptus lignosulfonate calcium (HLS-Ca) from hardwood and acrylic acid (AA) was investigated by using Fenton agent as a coinitiator. The influences of reaction conditions on grafting parameters i.e. product yield (Y%), AA conversion (C%), grafting ratio (G%) and grafting efficiency (GE%) were carefully studied. The effects of the phenolic hydroxyl (Ph-OH) group on the polymerization of AA and grafting reaction were researched. Graft copolymers were identified by the new absorption at 1727 cm^?1, more homogenized morphology and higher decomposition temperature after grafted with AA, as illustrated in FTIR, SEM and TG spectra. The optimum synthesis conditions are as follows: H₂O₂ = 25.2 mol/L, FeCl₂ = 63.0 mol/L, T = 50 °C and t = 2 h and the optimum percentages of Y, C, G and GE are 97.61%, 95.23%, 71.29% and 78.85%, respectively. The Ph-OH group of HLS-Ca cannot inhibit the polymerization of AA and is involved in the grafting reaction as an active center.     

Novel tricyclic pyrazolo[1,5-d][1,4]benzoxazepin-5(6H)-one: Design,synthesis, model and use as hMAO-B inhibitors

Based on our recently reported selective hMAO-A inhibitors, on which, the intramolecular cyclization led to a very interesting change of isoform selectivity. A series of selective hMAO-B inhibitors (3a–3u) with novel scaffold of tricyclic pyrazolo[1,5-d][1,4]benzoxazepin-5(6H)-one were designed and synthesized. Compound 3u (IC₅₀ = 221 nM) exhibited the best inhibitory activity and isoform selectivity against hMAO-B, superior to selegiline (IC₅₀ = 321 nM), which is a commercial selective hMAO-B inhibitor used to Parkinson’s disease. Modeling study indicated that the selectivity of our compounds to hMAO-B is determined by at least two residues, i.e., Ile 199 and Cys 172 (or corresponded Phe 208 and Asn 181 of hMAO-A). These data support further studies to assess rational design of more efficiently selective hMAO-B inhibitors.