The essence of DNA sample preparation for MALDI mass spectrometry

Matrix-assisted laser desorption/ionization (MALDI) mass spectrometry has become an important analytical technique in nucleic acid research. MALDI is used for quality control of oligonucleotides as well as for analyzing DNA markers. Sample preparation of nucleic acids is crucial for obtaining high-quality mass spectra. Sample purity, solvent content, suitable matrices, and substrate surfaces, as well as laboratory conditions affect spectra quality. This review presents essential information with regard to sample preparation, DNA modification chemistry, and DNA purification, along with a discussion of instrumental advances, which facilitate and extend the applicability of MALDI in genomics.     

Sugar additives for MALDI matrices improve signal allowing the smallest nucleotide change (A:T) in a DNA sequence to be resolved

Sample preparation for matrix-assisted laser desorption/ionization (MALDI) mass spectrometry (MS) of DNA is critical for obtaining high quality mass spectra. Sample impurity, solvent content, substrate surface and environmental conditions (temperature and humidity) all affect the rate of matrix–analyte co-crystallization. As a result, laser fluence threshold for desorption/ionization varies from spot to spot. When using 3-hydroxypicolinic acid (3-HPA) as the matrix, laser fluence higher than the threshold value reduces mass resolution in time-of-flight (TOF) MS as the excess energy transferred to DNA causes metastable decay. This can be overcome by either searching for ‘hot’ spots or adjusting the laser fluence. However, both solutions may require a significant amount of operator manipulation and are not ideal for automatic measurements. We have added various sugars for crystallization with the matrix to minimize the transfer of excess laser energy to DNA molecules. Fructose and fucose were found to be the most effective matrix additives. Using these additives, mass resolution for DNA molecules does not show noticeable deterioration as laser energy increases. Improved sample preparation is important for the detection of single nucleotide polymorphisms (SNPs) using primer extension with a single nucleotide. During automatic data acquisition it is difficult to routinely detect heterozygous A/T mutations, which requires resolving a mass difference of 9 Da, unless a sugar is added during crystallization.     

Comparison of IR- and UV-matrix-assisted laser desorption/ionization mass spectrometry of oligodeoxynucleotides.

UV-matrix assisted laser desorption/ionization mass spectrometry (UV-MALDI-MS) with 3-hydroxypicolinic acid as matrix and IR-MALDI-MS with succinic acid as matrix have proved their feasibility for highly accurate and sensitive mass determination of nucleic acids (DNA and RNA). In this work, a detailed comparison of these two MALDI-methods and between positive- and negative ion mass spectra for the analysis of oligodeoxynucleotides is undertaken. Mass spectra of DNA sequences with up to 40 nucleotides are shown. Both linear and reflectron time-of-flight mass analyzers were used within this study and are compared for their potential in the MALDI analysis of oligodeoxynucleotides. The role of molecule-ion fragmentation is also discussed.     

Sample preparation and bioinformatics in MALDI profiling of urinary proteins

One of the challenges of current proteomics research is identifying healthy and diseased mass spectrometric (MS) patterns within biological fluids. As a result, sample preparation methodologies, as well as the mathematical tools utilized for MS data analysis become pivotal. This study involves a thorough evaluation of the reproducibility and protein resolution that various urinary protein preparation methodologies provide in MALDI MS analysis. Several precipitation approaches, ultrafiltration, as well as direct dilution of urine in MALDI MS compatible buffers were applied in combination to a thorough bioinformatics analysis of the generated MS data. Our results indicate that ultrafiltration, as well as direct dilution of urine in TFA, can provide information rich and reproducible spectra for mass ranges up to 20 kDa. The importance of the presence of peak reproducibility filters when generating disease classification models is suggested.     

Evaluation of sample preparation methods for MALDI-TOF MS identification of highly dangerous bacteria

Aims: To propose a universal workflow of sample preparation method for the identification of highly pathogenic bacteria by MALDI‐TOF MS. Methods and Results: Fifteen bacterial species, including highly virulent Gram‐positive (Bacillus anthracis and Clostridium botulinum) and Gram‐negative bacteria (Brucella melitensis, Burkholderia mallei, Francisella tularensis, Shigella dysenteriae, Vibrio cholerae, Yersinia pestis and Legionella pneumophila), were employed in the comparative study of four sample preparation methods compatible with MALDI‐TOF MS. The yield of bacterial proteins was determined by spectrophotometry, and the quality of the mass spectra, recorded in linear mode in the range of 2000–20 000 Da, was evaluated with respect to the information content (number of signals) and quality (S/N ratio). Conclusions: Based on the values of protein concentration and spectral quality, the method using combination of ethanol treatment followed by extraction with formic acid and acetonitrile was the most efficient sample preparation method for the identification of highly pathogenic bacteria using MALDI‐TOF MS. Significance and Impact of the Study: The method using ethanol/formic acid generally shows the highest extraction efficacy and the spectral quality with no detrimental effect caused by storage. Thus, this can be considered as a universal sample preparation method for the identification of highly virulent micro‐organisms by MALDI‐TOF mass spectrometry.     

Mass spectrometric analysis of a UV-cross-linked protein-DNA complex: tryptophans 54 and 88 of E. coli SSB cross-link to DNA

Protein-nucleic acid complexes are commonly studied by photochemical cross-linking. UV-induced cross-linking of protein to nucleic acid may be followed by structural analysis of the conjugated protein to localize the cross-linked amino acids and thereby identify the nucleic acid binding site. Mass spectrometry is becoming increasingly popular for characterization of purified peptide-nucleic acid heteroconjugates derived from UV cross-linked protein-nucleic acid complexes. The efficiency of mass spectrometry-based methods is, however, hampered by the contrasting physico-chemical properties of nucleic acid and peptide entities present in such heteroconjugates. Sample preparation of the peptide-nucleic acid heteroconjugates is, therefore, a crucial step in any mass spectrometry-based analytical procedure. This study demonstrates the performance of four different MS-based strategies to characterize E. coli single-stranded DNA binding protein (SSB) that was UV-cross-linked to a 5-iodouracil containing DNA oligomer. Two methods were optimized to circumvent the need for standard liquid chromatography and gel electrophoresis, thereby dramatically increasing the overall sensitivity of the analysis. Enzymatic degradation of protein and oligonucleotide was combined with miniaturized sample preparation methods for enrichment and desalting of cross-linked peptide-nucleic acid heteroconjugates from complex mixtures prior to mass spectrometric analysis. Detailed characterization of the peptidic component of two different peptide-DNA heteroconjugates was accomplished by matrix-assisted laser desorption/ionization mass spectrometry and allowed assignment of tryptophan-54 and tryptophan-88 as candidate cross-linked residues. Sequencing of those peptide-DNA heteroconjugates by nanoelectrospray quadrupole time-of-flight tandem mass spectrometry identified tryptophan-54 and tryptophan-88 as the sites of cross-linking. Although the UV-cross-linking yield of the protein-DNA complex did not exceed 15%, less than 100 pmole of SSB protein was required for detailed structural analysis by mass spectrometry.     

生物质谱技术及其应用

质谱是带电粒子按质荷比大小顺序排列的图谱,最初主要用来测定元素或同位素的原子量,随着科学的发展及高性能质谱仪器的出现,质谱被越来越多地应用生命科学研究的许多领域,以其质辅助激光解吸附飞行时间质谱和电喷雾质谱为代表的现代生物质谱技术,为蛋白质等生物大分子的研究提供了必要的技术手段。本文在简介近年来比较常用的几种生物质谱技术的基础上,概述了生物质谱技术在蛋白质,核酸研究及检测分析等几个方面的初步应用。     

Mass spectrometry of nicotinic acetylcholine receptors and associated proteins as models for complex transmembrane proteins

Studies were conducted to optimize matrix-assisted laser desorption/ionization, time-of-flight mass spectrometry (MALDI TOF MS) in analyzing the composition of nicotinic acetylcholine receptors (nAChR) from Torpedo californica electric tissue in their membrane-bound, detergent-solubilized, and affinity-purified states. Mass spectra obtained from nAChR-rich membrane fractions gave reasonably good representations of protein compositions indicated by sodium dodecyl sulfate-polyacrylamide gel electrophoresis of those same samples. Efficiency of extraction of nAChR from membranes was not markedly different for most detergents, but quality and signal size of mass spectra were clearly influenced by detergent composition and concentration, protein concentration, and MALDI matrix composition. The best spectra, allowing detection and accurate size determinations for samples containing as little as 10 fmol of pure nAChR, were obtained for samples solubilized in Triton X-100 and assayed by use of a sinapinic acid matrix. Although informative spectra could be obtained for nAChR affinity purified on alpha-cobratoxin (Naja naja siamensis) columns and extracted using sinapinic acid, superior spectra with much higher signal:noise were obtained if extraction media contained Triton X-100 or sodium dodecyl sulfate. nAChR subunit masses determined were similar regardless of the membrane-associated, detergent-solubilized, or affinity-purified state of the preparation. These studies illustrate how masses can be determined for nAChR subunits and for other protein components in Torpedo membrane preparations, such as RAPsyn and Na(+)-K(+)-ATPase alpha and beta subunits. They also provide an underpinning for streamlined analysis of the composition of complex transmembrane proteins using MALDI TOF MS.     

Single-nucleotide polymorphisms: analysis by mass spectrometry

Matrix-assisted laser desorption-ionization (MALDI) mass spectrometry has evolved as a powerful method for analyzing nucleic acids. Here we provide protocols for genotyping single-nucleotide polymorphisms (SNPs) by MALDI based on PCR and primer extension to generate allele-specific products. Furthermore, we present three different approaches for sample preparation of primer-extension products before MALDI analysis and discuss their potential areas of application. The first approach, the 'GOOD' assay, is a purification-free procedure that uses DNA-modification chemistry, including alkylation of phosphorothioate linkages in the extension primers. The other two approaches use either solid-phase extraction or microarray purification for the purification of primer-extension products. Depending on the reaction steps of the various approaches, the protocols take about 6-8 hours.     

A mass-spectrometric approach to primary screening of collagenolytic enzymes

A comparative analysis of MALDI TOF mass spectra of low-molecular products resulting from the hydrolysis of native collagen I by collagenases of various classes (bacterial metallocollagenase from Clostridium histolyticum, serine collagenase from the Morikrasa commercial preparation, cysteine collagenase from Serratia proteomaculans, and cysteine collagenases from larvae of beetles Dermestesfrischi and D. maculates) was carried out. The spectra contain a number of ion peaks common for all collagenases; nevertheless, the mass spectra of each hydrolysate contains a unique set of peaks ("fingerprint") characteristic of each enzyme. This is especially true for the peaks of major products with relative intensities of more than 50%. At the same time, the enzymes of one class (cysteine collagenases) exhibit in their mass spectra peaks of identical major products. The results show a potential opportunity for MALDI TOF application in the primary screening of collagenases according to the fingerprints of collagen hydrolysis products.     

PAS‐cal: A repetitive peptide sequence calibration standard for MALDI mass spectrometry

Mass spectrometers equipped with matrix‐assisted laser desorption/ionization (MALDI‐MS) require frequent multipoint calibration to obtain good mass accuracy over a wide mass range and across large numbers of samples. In this study, we introduce a new synthetic peptide mass calibration standard termed PAS‐cal tailored for MALDI‐MS based bottom‐up proteomics. This standard consists of 30 peptides between 8 and 37 amino acids long and each constructed to contain repetitive sequences of Pro, Ala and Ser as well as one C‐terminal arginine residue. MALDI spectra thus cover a mass range between 750 and 3200 m/z in MS mode and between 100 and 3200 m/z in MS/MS mode. Our results show that multipoint calibration of MS spectra using PAS‐cal peptides compares well to current commercial reagents for protein identification by PMF. Calibration of tandem mass spectra from LC‐MALDI experiments using the longest peptide, PAS‐cal37, resulted in smaller fragment ion mass errors, more matching fragment ions and more protein and peptide identifications compared to commercial standards, making the PAS‐cal standard generically useful for bottom‐up proteomics.     

Sample preparation issues for tissue imaging by imaging MS

Imaging MS is a powerful technique that combines the chemical and spatial analysis of surfaces. It allows spatial localization of multiple different compounds that are recorded in parallel without the need of a label. It is currently one of the rapidly developing techniques in the proteomics toolbox. Different complementary imaging MS methods, i.e. MALDI and secondary ion MS imaging for direct tissue analysis, can be applied on exactly the same tissue sample. This allows the identification of small molecules, peptides and proteins present on the same sample surface. Sample preparation is crucial to obtain high quality, reliable and reproducible complementary molecular images. It is essential to optimize the conditions for each step in the sample preparation protocol, ranging from sample collection and storage to surface modification. In this article, we review and discuss the importance of correct sample treatment in case of MALDI and secondary ion MS imaging experiments and describe the experimental requirements for optimal sample preparation.     

The use of mass spectrometry in genomics

Recent advances in the development of electrospray ionization (ESI) and matrix-assisted laser desorption/ionization (MALDI) now permit the near routine analysis of oligonucleotides and intact nucleic acids. These developments have led to the use of mass spectrometry (MS) as a detection platform for genomics studies. Among the various uses of mass spectrometry in genomics, applications focused on the characterization of single nucleotide polymorphisms (SNPs) and short tandem repeats (STRs) are particularly well-suited to MALDI or ESI-based analysis. It is predicted that continued developments in methodology and instrumentation will further improve the capabilities of mass spectrometry for nucleic acid analysis.     

Optimization of MALDI-TOF MS for strain level differentiation of Arthrobacter isolates

Matrix-assisted laser-desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) has been shown to be a rapid and sensitive method for characterization of bacteria, but it has not yet become a routine microbiological procedure. Currently there are no standardized protocols that would allow development of large libraries of reproducible protein profiles from a broad range of microorganisms to use for identification purposes. Important variables that may affect spectrum quality are MALDI matrices, solvents, cell growth condition, and culture age. In the present study our aim was to: (1) to determine optimal sample preparation and MALDI conditions for discrimination at the strain level; (2) to determine if changes in growth cycle correlated with MALDI spectrum changes; and (3) to compare level of isolate discrimination based on their MALDI spectra versus their 16S rRNA gene sequence. Using 16 strains of the Gram positive bacterium Arthrobacter, optimal spectra were obtained using two-layer sample application of intact cells grown on solid surface overlaid with a matrix consisting of sinapinic acid (SA) or alpha-cyano-hydroxy-cinnaminic acid (CHCA) in 50:50 acetonitrile:water solvent with 2% trifluoroacetic acid. Spectrum changes paralleled the coccus-rod-coccus growth cycle indicative of Arthrobacter. Strain differences based on their MALDI profiles (using Pearson coefficient and UPGMA) corresponded with their 16S rRNA gene phylogeny but it had greater discrimination.     

A mass-spectrometric approach to primary screening of collagenolytic enzymes

A comparative analysis of MALDI TOF mass spectra of low-molecular products resulting from the hydrolysis of native collagen I by collagenases of various classes (bacterial metallocollagenase from Clostridium histolyticum, serine collagenase from the Morikrasa commercial preparation, cysteine collagenase from Serratia proteomaculans, and cysteine collagenases from larvae of beetles Dermestes frischi and D. maculatus) was carried out. The spectra contain a number of ion peaks common for all collagenases; nevertheless, the mass spectra of each hydrolysate contains a unique set of peaks (“fingerprint”) characteristic of each enzyme. This is especially true for the peaks of major products with relative intensities of more than 50%. At the same time, the enzymes of one class (cysteine collagenases) exhibit in their mass spectra peaks of identical major products. The results show a potential opportunity for MALDI TOF application in the primary screening of collagenases according to the fingerprints of collagen hydrolysis products.     

MALDI-TOF mass spectrometry: a versatile tool for high-performance DNA analysis

Matrix-assisted laser desorption/ionization (MALDI) time-of-flight (TOF) mass spectrometry (MS) has developed during the past decade into a versatile tool for biopolymer analysis. The aim of this review is to summarize this development and outline the applications, which have been enabled for routine use in the field of nucleic acid analysis. These include the analysis of mutations, the resequencing of amplicons with a known reference sequence, and the quantitative analysis of gene expression and allelic frequencies in complex DNA mixtures.     

MALDI-TOF mass spectrometry

Matrix-assisted laser desorption/ionization (MALDI) time-of-flight (TOF) mass spectrometry (MS) has developed during the past decade into a versatile tool for biopolymer analysis. The aim of this review is to summarize this development and outline the applications, which have been enabled for routine use in the field of nucleic acid analysis. These include the anlaysis of mutations, the resequencing of amplicons with a known reference sequence, and the quantitative analysis of gene expression and allelic frequencies in complex DNA mixtures.     

Potential Pitfalls in MALDI-TOF MS Analysis of Abiotically Synthesized RNA Oligonucleotides

Demonstration of the abiotic polymerization of ribonucleotides under conditions consistent with conditions that may have existed on the prebiotic Earth is an important goal in “RNA world” research. Recent reports of abiotic RNA polymerization with and without catalysis rely on techniques such as HPLC, gel electrophoresis, and MALDI-TOF MS to analyze the reaction products. It is essential to understand the limitations of these techniques in order to accurately interpret the results of these analyses. In particular, techniques that rely on mass for peak identification may not be able to distinguish between a single, linear RNA oligomer and stable aggregates of smaller linear and/or cyclic RNA molecules. In the case of MALDI-TOF MS, additional complications may arise from formation of salt adducts and MALDI matrix complexes. This is especially true for abiotic RNA polymerization reactions because the concentration of longer RNA chains can be quite low and RNA, as a polyelectrolyte, is highly susceptible to adduct formation and aggregation. Here we focus on MALDI-TOF MS analysis of abiotic polymerization products of imidazole-activated AMP in the presence and absence of montmorillonite clay as a catalyst. A low molecular weight oligonucleotide standard designed for use in MALDI-TOF MS and a 3′-5′ polyadenosine monophosphate reference standard were also run for comparison and calibration. Clay-catalyzed reaction products of activated GMP and UMP were also examined. The results illustrate the ambiguities associated with assignment of m/z values in MALDI mass spectra and the need for accurate calibration of mass spectra and careful sample preparation to minimize the formation of adducts and other complications arising from the MALDI process.