Thiolated pyrrolidinyl peptide nucleic acids for the detection of DNA hybridization using surface plasmon resonance

Thiolated pyrrolidinyl peptide nucleic acids (HS-PNAs) bearing d-prolyl-2-aminocyclopentanecarboxylic acid (ACPC) backbones with different lengths and types of thiol modifiers were synthesized and then characterized by MALDI–TOF mass spectrometry. These HS-PNAs were immobilized on gold-coated glass by self-assembled monolayer (SAM) formation via S atom linkage for the detection of DNA hybridization using surface plasmon resonance (SPR). The amount and the stability of the immobilized HS-PNAs, as well as the effects of spacer and blocking thiol on DNA hybridization efficiency, were determined. SPR results indicated that the hybridization efficiency was enhanced when the distance between the PNA portion and the thiol terminal was increased and/or when blocking thiol was used following the HS-PNA immobilization. The immobilized HS-PNA could discriminate between fully complementary DNA from one or two base mismatched DNA with a relatively high degree of mismatch discrimination (>45%) in PBS buffer at 25 °C. The lowest DNA concentration at which reliable discrimination between fully complementary and single mismatched DNA could still occur was at about 0.2 μM, which is equivalent to 10 pmol of DNA. This research demonstrates that using these novel thiolated PNAs in combination with the SPR technique offers a direct, rapid and non-label based method that could potentially be applied for the analysis of genomic or PCR-amplified DNA in the future.     

Synthesis of a stable and specific surface plasmon resonance biosensor surface employing covalently immobilized peptide nucleic acids

Biosensors allow the real-time and label-free observation of biochemical reactions between various ligands including antigen-antibody reactions and nucleic acids hybridizations. In our studies, we used a surface plasmon resonance biosensor to elucidate the hybridization characteristics of a peptide nucleic acid (PNA) ligand immobilized on sensor surfaces either through covalent or streptavidin-biotin coupling. A biotin-labeled PNA was employed in the latter approach whereas the covalent immobilization included the following steps: A maleimide group was attached to the N-terminal of the PNA using N-succinimidyl 4-(N-maleimidomethyl)-cyclohexane-1-carboxylate (SMCC). To generate free thiol groups for coupling, a carboxylated dextran matrix of the sensor surface was activated with N-hydroxysuccinimide (NHS) and N-ethyl-N'-(dimethylaminopropyl)-carbodiimide (EDC) and thiolated by addition of cystamine dihydrochloride followed by reduction with 1, 4-dithioerythrite (DTE). Finally, the modified PNA was coupled to the sulfhydryl groups of the activated dextran matrix. Repetitive hybridizations of a single-stranded synthetic DNA oligomer to the PNAs demonstrated the superior stability of covalent immobilization compared to noncovalent immobilization. Differentiation of point mutations in the analyte molecule was accomplished at 40 degrees C using guanidine thiocyanate concentrations of 1.5-1.7 M. In further experiments, we showed that a perfectly matched PNA allows the detection of a single-stranded DNA at a sensitivity of less than 1% in a background of single-stranded DNA having a single C to T point mutation in the region complementary to the PNA. Consequently, covalently bound PNAs provide a stable and reproducible environment for the development of mutation-specific DNA analysis assays.     

A hand-held surface plasmon resonance biosensor for the detection of ricin and other biological agents

There is an ongoing need for field-deployable biosensor devices. We have constructed a fully self-contained, hand-held biosensor, based on the surface plasmon resonance technique. The dimensions of the sensor unit are 15 x 8 cm, the weight is 600 g and it is powered by a 9 V battery. We have characterised the responsiveness of the sensor using calibrated sucrose solutions and were able to measure changes as small as 3.3 x 10(-6) refractive index units. To demonstrate functionality of the sensor, we have prepared surfaces with an antibody fragment specific for the biological toxin ricin. We were able to detect ricin at 200 ng/mL in 10 min, which is approximately 2500 times less than the minimum lethal dose. We were also able to verify positive binding within a second 10 min window. This sensor demonstrates important steps required for the development of fully integrated, hand-held sensor devices and will form the basis of a multi-analyte system, to be developed in the near future. It also represents the first completely hand-held SPR device, not requiring external power or a computer connection to operate.     

Integrated-optic biosensor by electro-optically modulated surface plasmon resonance

We present a new integrated-optic surface plasmon resonance (SPR) biosensor based on electro-optical modulation. The SPR characteristics for the analyte concentration detection can be electro-optically modulated by applying the voltage on the electrodes of the biosensor fabricated on lithium niobate, which is an excellent electro-optic material. Two measurement methods, electro-optically modulated SPR spectral measurement and electro-optically modulated SPR intensity measurement, are demonstrated and their measurands are the SPR wavelength and the output optical intensity, respectively. Human serum albumin is coated on the gold film surface of the proposed biosensor to detect the concentration of beta-blocker, which is a remedy for heart disease. As the applied voltage increases such that the effective index of guided mode rises, the SPR wavelength shifts toward the long wavelength side and the output optical intensity at the wavelength of 632.8 nm diminishes. The linear regression slope of the relation between the measurand and the applied voltage is dependent on the analyte concentration and can be used to determine the concentration variation. Experimental results measured by the electro-optically modulated SPR methods are compared with those measured by the conventional spectral and intensity methods, and the effects of waveguide width on the biosensor performance are discussed.     

Advances in surface plasmon resonance biosensor analysis

The number and diversity of surface plasmon resonance (SPR) biosensor applications continue to increase. Evolutions in instrument and sensor chip technology, experimental methodology, and data analysis are making it possible to examine a wider variety of biomolecular interactions in greater mechanistic detail. SPR biosensors are poised to make a significant impact in basic research and pharmaceutical discovery.     

Immobilization of metallothionein as a sensitive biosensor chip for the detection of metal ions by surface plasmon resonance

A biosensor based on mammalian metallothionein (MT) for the detection of metal ions was developed and characterized. MT was immobilized onto a carboxymethylated dextran matrix as a biosensor for the detection of metal ions by surface plasmon resonance (SPR). The optimal pH for the immobilization step was determined to be 4. The temperature for the analysis was also defined, and the highest interaction was observed at 30 degrees C. The MT sensor chip binds cadmium (Cd), zinc (Zn) or nickel (Ni), but not magnesium (Mg), manganese (Mn) and calcium (Ca). Calibration curves for the quantification of metal ions showed excellent linearity. The sensitivity for metal detection is at the micromolar level. The interaction between the metal ions and the sensor chip is influenced significantly by the presence of NaCl, Tween 20 and the pH of the reaction buffer. By decreasing the NaCl in the reaction buffer to 1 mM, the MT chip effectively differentiates cadmium from zinc and nickel. Kinetic parameters of the metal-MT interactions were also determined by using this chip. The binding affinity between the metal ions and the immobilized MT follows the order of cadmium > zinc > nickel, which is the same as that determined for MT in solution. Thus, the MT chip can be an effective biosensor for the detection and measurement of several metal ions.     

Label-free and high-sensitive detection of Salmonella using a surface plasmon resonance DNA-based biosensor

A method based on surface plasmon resonance (SPR) DNA biosensor has been developed for label-free and high-sensitive detection of Salmonella. A biotinylated single-stranded oligonucleotide probe was designed to target a specific sequence in the invA gene of Salmonella and then immobilized onto a streptavidin coated dextran sensor surface. The invA gene was isolated from bacterial cultures and amplified using a modified semi-nested asymmetric polymerase chain reaction (PCR) technique. In order to investigate the hybridization detection, experiments with different concentration of synthetic target DNA sequences have been performed. The calibration curve of synthetic target DNA had good linearity from 5 nM to 1000 nM with a detection limit of 0.5 nM. The proposed method was applied successfully to the detection of single-stranded invA amplicons from three serovars of Salmonella, i.e., Typhimurium, Enterica and Derby, and the responses to PCR products were related to different S. typhimurium concentrations in the range from 10(2) to 10(10) CFU mL(-1). While with this system to detect E. coli and S. aureus, no significant signal was observed, demonstrating good selectivity of the method. In addition, the hybridization can be completed within 15 min, and the excellent sensor surface regeneration allows at least 300 assay cycles without obvious loss of performance.     

Enhanced recognition of cystic fibrosis W1282X DNA point mutation by chiral peptide nucleic acid probes by a surface plasmon resonance biosensor

Peptide nucleic acids (PNAs) containing an insert of three chiral monomers based on D-lysine ('chiral box') were synthesized and used as probes in Biospecific Interaction Analysis (BIA) for the recognition of DNA containing the W1282X point mutation of the cystic fibrosis gene. Hybridization experiments carried out in solution showed enhanced mismatch recognition when compared with the analogous achiral PNAs and oligonucleotides. The signal intensity was lower, but the selectivity of the Biacore response was found to be much higher than that observed with achiral PNAs. The newly designed chiral PNA probes were also found to hybridize with a 1:1 mixture of normal (N-W1282X) and mutated (M-W1282X) DNA oligomers immobilized on the biosensor, thus allowing discrimination not only between a normal and a mutated sequence (healthy/homozygous), but also between homo- and heterozygous individuals. These results suggest that 'chiral box' PNAs are potential powerful tools for the analysis of single point mutations of biological/biomedical relevance.     

A DNA sensor based on surface plasmon resonance for apoptosis-associated genes detection

A practical and simple DNA sensor based on surface plasmon resonance (SPR) had been developed to determine apoptosis-associated genes, bcl-2 and bax. This SPR sensor was designed on the basis of simultaneous multi-wavelength detection. The complementary sequences of bcl-2 or bax oligonucleotide labeled with biotin were used as the probes. Biotin-avidin system was used to immobilize the bio-DNA on the sensor surface. The assembling processes and conditions for the DNA sensor were examined. The SPR sensor could be used to monitor the process of the immobility of the bio-DNA and DNA hybridization in real-time. The determination range of bcl-2 and bax oligonucleotide (20 bases) were 50-400 ng/mL. The determination range of polymerase chain reaction (PCR) product of bcl-2 (405 bases) was 5-60 ng/mL and PCR product of bax (538 bases) was 5-40 ng/mL. The stability, reversibility and specificity of the DNA sensor were also investigated. It was found from the experiment that the sensor could be applied for a quite long time (about 90 times). The relative standard deviation (R.S.D.) for determination oligonucleotides and PCR products of bcl-2 were 1.2 and 1.3%, respectively. The interference of noncomplementary DNA sequence with the determination of DNA was examined and it was found that noncomplementary 20-mer and 21-mer DNA (p53 and p21) do not affect the determination of bcl-2 or bax. This device could be used to study apoptosis and signal transduction routine genes. The sensor was shown to be of simplicity, sensitivity, selectivity, rapid response and cost effectiveness.     

Development of a surface plasmon resonance biosensor for the identification of Campylobacter jejuni

The purpose of this study was to develop a biosensor based on surface plasmon resonance (SPR) for the rapid identification of C. jejuni in broiler samples. We examined the specificity and sensitivity of commercial antibodies against C. jejuni with six Campylobacter strains and six non-Campylobacter bacterial strains. Antigen-antibody interactions were studied using enzyme-linked immunosorbent assay (ELISA) and a commercially available SPR biosensor platform (Spreeta). Campylobacter cells killed with 0.5% formalin had significant lower antibody reactivity when compared to live cells, or cells inactivated with 0.5% thimerosal or heat (70 degrees C for 3 min) using ELISA. The SPR biosensor showed a good sensitivity with commercial antibodies against C. jejuni at 10(3) CFU/ml and a low cross reactivity with Salmonella serotype typhimurium. The sensitivity of the SPR was similar when testing spiked broiler meat samples. However, research is still needed to reduce the high background observed when sampling meat products.     

Survey of the 1999 surface plasmon resonance biosensor literature

The application of surface plasmon resonance biosensors in life sciences and pharmaceutical research continues to increase. This review provides a comprehensive list of the commercial 1999 SPR biosensor literature and highlights emerging applications that are of general interest to users of the technology. Given the variability in the quality of published biosensor data, we present some general guidelines to help increase confidence in the results reported from biosensor analyses.     

A surface plasmon resonance array biosensor based on spectroscopic imaging

We have developed a multi-element transduction system which combines conventional SPR spectroscopy with one-dimensional SPR microscopy to create an effective platform for monitoring binding events on macro- or micro-patterned receptor arrays created on disposable sensor chips. This creates an effective platform for monitoring simultaneous binding events on each of the regions patterned with the receptors. This system has been specifically designed with commercially available components to allow relatively easy duplication. Furthermore, this system can use a proven, simple method to compensate for changes in the bulk index of refraction of the solution containing the analytes due to changes in temperature or solute concentration with simple modifications to the sensor chips alone. Preliminary results demonstrate how this system can be used to monitor several independent biospecific binding events simultaneously.     

Detection of cadmium by a fiber-optic biosensor based on localized surface plasmon resonance

A novel transmission-based localized surface plasmon resonance (LSPR) fiber-optic probe has been developed to determine the heavy metal cadmium ion (Cd(II)) concentration. The LSPR sensor was constructed by immobilizing phytochelatins (PCs), (gammaGlc-Cys)(8)-Gly, onto gold nanoparticle-modified optical fiber (NM(Au)OF). The optimal immobilizing conditions of PCs on to the NM(Au)OF are 71.6mug/ml PCs in pH 7.4 PBS for 2h. The absorbability (change of light absorption) of the PC-functionalized NM(Au)OF sensor increases to 9% upon changing the Cd(II) level from 1 to 8ppb with a sensitivity of 1.24ppb(-1) and a detection limit of 0.16ppb. The sensor retained 85% of its original activity after nine cycles of deactivation and reactivations. In addition, the sensor retains its activity and gives reproducible results after storage in 5% d-(+)-trehalose dehydrate solution at 4 degrees C for 35 days. The dissociation constant (K(d)) of the immobilized PCs with Cd(II) was about 6.77x10(-8)M. In conclusion, the PCs-functionalized NM(Au)OF sensor can be used to determine the concentration of Cd(II) with high sensitivity.     

Development of a surface plasmon resonance biosensor for real-time detection of osteogenic differentiation in live mesenchymal stem cells

Surface plasmon resonance (SPR) biosensors have been recognized as a useful tool and widely used for real-time dynamic analysis of molecular binding affinity because of its high sensitivity to the change of the refractive index of tested objects. The conventional methods in molecular biology to evaluate cell differentiation require cell lysis or fixation, which make investigation in live cells difficult. In addition, a certain amount of cells are needed in order to obtain adequate protein or messenger ribonucleic acid for various assays. To overcome this limitation, we developed a unique SPR-based biosensing apparatus for real-time detection of cell differentiation in live cells according to the differences of optical properties of the cell surface caused by specific antigen-antibody binding. In this study, we reported the application of this SPR-based system to evaluate the osteogenic differentiation of mesenchymal stem cells (MSCs). OB-cadherin expression, which is up-regulated during osteogenic differentiation, was targeted under our SPR system by conjugating antibodies against OB-cadherin on the surface of the object. A linear relationship between the duration of osteogenic induction and the difference in refractive angle shift with very high correlation coefficient was observed. To sum up, the SPR system and the protocol reported in this study can rapidly and accurately define osteogenic maturation of MSCs in a live cell and label-free manner with no need of cell breakage. This SPR biosensor will facilitate future advances in a vast array of fields in biomedical research and medical diagnosis.     

Quantitative assay of hepatitis B surface antigen by using surface plasmon resonance biosensor

We performed a basic experiment for the rapid, on-line, real-time measurement of hepatitis B surface antigen using a surface plasmon resonance biosensor. We immobilized anti-HBsAg (hepatitis B surface antigen) polyclonal antibody, as a ligand, to the dextran layer on a CM5 chip surface that had previously been activated byN-hydroxysuccinimide. A sample solution containing HBsAg was fed through a microfluidic channel, and the reflecting angle change due to the mass increase from the binding was detected. The binding characteristics between HBsAg and its polyclonal antibody followed the typical monolayer adsorption isotherm. When the entire immobilized antibody had interacted, no additional, non-specific binding occurred, suggesting the immunoreaction was very specific. The bound antigen per unit mass of the antibody was independent of the immobilized ligand density. No significant steric hindrance was observed at an immobilization density of approximately 17.6 ng/mm². The relationship between the HBsAg concentration in the sample solution and the antigen bound to the ligand was linear up to ca. 40 μg/mL. This linearity was much higher than that of the ELISA method. It appeared the antigen-antibody binding increased as the immobilized ligand density increased. In summary, this study showed the potential of this SPR biosensor-based method as a rapid, simple and multi-sample on-line assay. Once properly validated, it may serve as a more efficient method for HBsAg quantification for replacing the ELISA.     

Determination of organophosphorous pesticides by a novel biosensor based on localized surface plasmon resonance

Liquid and gas chromatography are commonly used to measure organophosphorus pesticides. However, these methods are relatively time consuming and require a tedious sample pretreatment. Here, we applied the localized surface plasmon resonance (LSPR) of gold nanoparticles covalently coupled with acetylcholinesterase (AChE) to create a biosensor for detecting an example of serial signals responding to paraoxon in the range of 1-100 ppb by an AChE modified LSPR sensor immersing in a 0.05 mM ACh solution. The underlying mechanism is that paraoxon prevents acetylcholine chloride (ACh) reacting with AChE by destroying the OH bond of serine in AChE. We found that the AChE modified LSPR sensors prepared by incubation with 12.5 mU/mL of AChE in phosphate buffer solution at pH 8.5 room temperature for 14 h have the best linear inhibition response with a 0.234 ppb limit of paraoxon detection. A 14% of inhibition on the sensor corresponds to the change of paraoxon concentration from 1 to 100 ppb. The sensor remained 94% of its original activity after six cycles of inhibition with 500 ppb paraoxon followed with reactivation of AChE by 0.5 mM 2-pyriding-aldoxime methoiodide (2-PAM). In addition, the sensor retains activity and gives reproducible results after storage in dry state at 4 degrees C for 60 days. In conclusion, we demonstrated that the AChE modified LSPR sensors can be used to determine the concentration of paraoxon biosensor with high sensitive and stable characteristics.     

Grating-based surface plasmon resonance detection of core-shell nanoparticle mediated DNA hybridization

In this report, we have investigated enhanced surface plasmon resonance (SPR) detection of DNA hybridization using gold core - silica shell nanoparticles in localized plasmonic fields. The plasmonic fields were localized by periodic linear gratings. Experimental results measured for hybridization of 24-mer single-stranded DNA oligomers suggest that core-shell nanoparticles (CSNPs) on gratings of 400 nm period provide enhanced optical signatures by 36 times over conventional thin film-based SPR detection. CSNP-mediated DNA hybridization produced 3 times larger angular shift compared to gold nanoparticles of the same core size. We have also analyzed the effect of structural variation. The enhancement using CSNPs was associated with increased surface area and index contrast that is combined by improved plasmon coupling with localized fields on gratings. The combined approach for conjugated measurement of a biomolecular interaction on grating structures is expected to lower the limit of detection to the order of a few tens of fg/mm(2).     

Circulating microRNA breast cancer biomarker detection in patient sera with surface plasmon resonance imaging biosensor

In this article, we report for the first time, the detection of circulating miRNA as a breast cancer biomarker in patient sera using surface plasmon resonance imaging biosensor. The advantage of this approach lies in the rapid, label-free and sensitive detection. The sensor excites plasmonic resonance on the gold sensor surface and specific DNA-miRNA molecular bindings elucidate responses in the plasmonic resonance image. Experiments of detecting synthetic miRNA molecules (miR-1249) were performed and the sensor resolution was found to be 63.5 nM. The sensor was further applied to screen 17 patient serum samples from National Cancer Centre Singapore and Tan Tock Seng Hospital. Sensor intensity response was found to differ by 20% between malignant and benign cases and thus forms, a potential and an important metric in distinguishing benignity and malignancy.