Use of impedance test for testing effectiveness of drug preservatives

Pharmacopoeias contain preservation efficacy test for estimating antimicrobial activity of chemical compounds added to pharmaceutical preparations in multidose containers in order to inhibit bioburden growth. This method involves the treating of preserved products with bacteria and yeast cells and monitoring the survival of microorganisms through the specified time periods up to 28 days. The last stage of assay--incubation and colony counting--is very time consuming. Recent advance in technology enables faster and more convenient detection in comparison to traditional methods. Impedance method is based on the principle that conductance and capacitance of cultivation medium increases when bacteria grow and metabolize, Impedance time detection is inversely proportional to initial bacterial population. Six different products were utilised throughout the study. The calibration curves were calculated for each of the tested strains by comparison between standard plate count method and detection time measured in Bactometer system. In our study log reduction calculated in alternative method were similar to those obtained in plate count assay. All of the tested preparations, except one, exhibited acceptable activity against bacteria and fungi and meet the pharmacopoeal requirements. The studies indicated a positive correlation between standard plate count results and impedance reading. The procedure with the usage of Bactometer, provides a rapid and accurate system for the determination of bacterial content.     

A medium for the detection of Lancefield Group D cocci in skimmed milk powder by measurement of conductivity changes

A selective medium for the detection of Lancefield Group D cocci in skimmed milk powder by conductivity measurements was developed and evaluated using the Bactometer M123 and Malthus 128H systems. This medium promoted large changes in conductance and capacitance. The calibration curve of detection times vs concentration of Lancefield Group D cocci showed a linear correlation coefficient of 0.93 and the method gave comparable results in both conductivity instruments. Naturally contaminated samples containing c. 10(3) cfu/g of Lancefield Group D cocci gave detection times within 16-18 h which was sufficiently rapid for the medium to be used for the routine screening of skimmed milk powder.     

Detection of viable Salmonella using microelectrode-based capacitance measurement coupled with immunomagnetic separation

In this study, we demonstrated the use of a general medium--brain heart infusion (BHI) broth that is not specifically formulated for impedance measurement, to achieve detectable impedance signals by using an interdigitated microelectrode (IME) with capacitance measurement at low frequencies. Anti-Salmonella antibody coated immunomagnetic beads were used to separate S. typhimurium from samples to provide the selectivity to this method. From analysis based on the equivalent circuit of the IME system, we found that the impedance change in BHI broth resulting from the growth of Salmonella was indeed the change in the double layer capacitance and could be monitored at 10 Hz using the IME. The results indicated that medium modification to improve impedance signal is not necessary with this IME system. However, effective immunological separation for the target organism is required for the selectivity when non-selective media are used. This finding provides a more flexible option of medium in impedance methods, which may provide opportunities to test those species of bacteria that have no suitable conductance growth medium. The detection time, t(d), was obtained from the impedance growth curve (impedance against bacterial growth time) at 10 Hz at the point where the impedance started to change. A linear relationship between the detection time and the logarithmic value of the initial cell number (N) was found in the Salmonella cell number ranging from 10(1) to 10(6) cfu/ml. The regression equation was t(d) = -1.22Log N + 8.90, with R2 = 0.95. The detection times for the initial cell number of 10(1) CFU/ml and 10(6) CFU/ml are 8 h and 1.5 h, respectively. This method is more sensitive than impedance methods using conventional electrodes.     

A medium for the detection of Lancefield Group D cocci in skimmed milk powder by measurement of conductivity changes

A selective medium for the detection of Lancefield Group D cocci in skimmed milk powder by conductivity measurements was developed and evaluated using the Bactometer M123 and Malthus 128H systems. This medium promoted large changes in conductance and capacitance. The calibration curve of detection times vs concentration of Lancefield Group D cocci showed a linear correlation coefficient of 0.93 and the method gave comparable results in both conductivity instruments. Naturally contaminated samples containing c. 10³ cfu/g of Lancefield Group D cocci gave detection times within 16–18 h which was sufficiently rapid for the medium to be used for the routine screening of skimmed milk powder.     

Interdigitated microelectrode (IME) impedance sensor for the detection of viable Salmonella typhimurium

Interdigitated microelectrodes (IMEs) were used as impedance sensors for rapid detection of viable Salmonella typhimurium in a selective medium and milk samples. The impedance growth curves, impedance against bacterial growth time, were recorded at four frequencies (10Hz, 100Hz, 1kHz, and 10kHz) during the growth of S. typhimurium. The impedance did not change until the cell number reached 10(5)-10(6) CFUml(-1). The greatest change in impedance was observed at 10Hz. To better understand the mechanism of the IME impedance sensor, an equivalent electrical circuit, consisting of double layer capacitors, a dielectric capacitor, and a medium resistor, was introduced and used for interpreting the change in impedance during bacterial growth. Bacterial attachment to the electrode surface was observed with scanning electron microscopy, and it had effect on the impedance measurement. The detection time, t(D), defined as the time for the impedance to start change, was obtained from the impedance growth curve at 10Hz and had a linear relationship with the logarithmic value of the initial cell number of S. typhimurium in the medium and milk samples. The regression equations for the cell numbers between 4.8 and 5.4 x 10(5) CFUml(-1) were t(D) = -1.38 log N + 10.18 with R(2) = 0.99 in the pure medium and t(D) = -1.54 log N + 11.33 with R(2) = 0.98 in milk samples, respectively. The detection times for 4.8 and 5.4 x 10(5) CFUml(-1) initial cell numbers were 9.3 and 2.2 h, respectively, and the detection limit could be as low as 1 cell in a sample.     

成骨细胞介电特性检测的方法研究

目的:以小鼠成骨细胞为材料,建立一套完整的用于成骨细胞的介电特性检测方法。方法:本研究首先是设计制作不同形状和尺寸的细胞介电谱检测装置(测量池),其次进行测量池的生物相容性评价,包括浸提液毒性实验,HE染色观察细胞形态。最后将细胞培养在测量池中,连入阻抗分析仪在20Hz~10MHz检测并联电导Gp和电容Cp并绘制介电谱图。结果:生物相容性检测表明测量池对细胞无毒性,可使用。此外,介电特性检测结果表明随着频率的增大,细胞的电容减小,电导略微增大后减小;随着培养时间的增长,电容值增大而电导值减小;经中强磁场处理后,细胞的电容和电导值都有下降。结论:该方法能够为其他贴壁细胞的介电特性检测提供研究基础,并对于在此基础上展开的贴壁细胞介电特性解析提供参考。     

散孔材和环孔材树种叶水分传输能力及其与抗旱性的关系

选取树龄相同的3种散孔材(杨树、梧桐和樱花)和3种环孔材(刺槐、合欢和白蜡)树种,用3种不同方法(解剖法、加压法和水容法)研究了其叶水力导度的差异及与抗旱性(PV曲线参数)的关系.结果显示:解剖法估算的最大叶水力导度高于加压法和水容法,加压法和水容法在6个树种中的5个上测定值完全一致,3种散孔材与环孔材树种的叶最大水力导度无显著差异.3种散孔材树种的饱和渗透势和膨压损失点渗透势与3种环孔材相比差异不大,但膨压损失点的相对含水量则低于环孔材树种,质外体含水量高于环孔材树种,导致其综合抗旱性指数也高于3种环孔材树种.研究表明,散孔材和环孔材树种的叶最大水力导度与其抗旱性之间并无显著相关关系.     

Probing the stability of S-layer-supported planar lipid membranes

Isolated protein subunits of the crystalline bacterial cell surface layer (S-layer) of Bacillus coagulans E38-66 have been recrystallized on one side of planar black lipid membranes (BLMs) and their influence on the electrical properties, rupture kinetics and mechanical stability of the BLM was investigated. The effect on the boundary potential, the capacitance or the conductance of the membrane was negligible whereas the mechanical properties were considerably changed. The mechanical stability was characterized by applying voltage pulses or ramps to induce irreversible rupture. The amplitude of the voltage pulse leading to rupture allows conclusions on the ability of membranes to resist external forces. Surprisingly, these amplitudes were significantly lower for composite S-layer/lipid membranes compared to undecorated BLMs. In contrast, the delay time between the voltage pulse and the appearance of the initial defect was found to be drastically longer for the S-layer-supported lipid bilayer. Furthermore, the kinetics of the rupture process was recorded. Undecorated membranes show a fast linear increase of the pore conductance in time, indicating an inertia-limited defect growth. The attachment of an S-layer causes a slow exponential increase in the conductance during rupture, indicating a viscosity-determined widening of the pore. In addition, the mechanical properties on a longer time scale were investigated by applying a hydrostatic pressure across the BLMs. This causes the BLM to bulge, as monitored by an increase in capacitance. Compared to undecorated BLMs, a significantly higher pressure gradient has to be applied on the S-layer face of the composite BLMs to observe any change in capacitance. Received: 4 May 1999 / Revised version: 1 July 1999 / Accepted: 1 July 1999     

Factors influencing capacitance-based monitoring of microbial growth.

Microbiological impedance devices are routinely used by food and manufacturing industries, and public health agencies to measure microbiological growth. Factors contributing to increases and decreases in capacitance at the culture medium-electrode interface are poorly understood. To objectively evaluate the effects of temperature, cell density and medium conductivity on capacitance, admittance values from an impedance device were standardized; capacitance was converted to susceptance to allow unit comparisons with conductance. Although increases in temperature increased susceptance, a linear relationship could not be established between the change of susceptance with temperature and conductance of the medium. Cell density by itself had no measureable effect on susceptance or conductance, indicating that cells did not impede the movement of ions in the medium or around the electrode. In a low conductivity medium, increases in conductance by the addition of ions resulted in a concomitant increase of susceptance values. However, in a high conductivity medium, increases in conductance resulted in little or no increase of susceptance values because ions saturated the electrode surface. Susceptance increased when Escherichia coli, Pseudomonas aeruginosa, Alcaligenes faecalis and Staphylococcus aureus were grown in high conductivity media because protons produced by metabolically active bacteria balance more charge on the electrode than other ions. Increases in susceptance due to bacterial growth and metabolism in low conductivity media were attributed to both increases in protons and ionic metabolites. These results indicate that capacitance may provide a better measure of microbial growth and metabolism than conductance.     

Heterotrophic plate counts of surface water samples by using impedance methods.

Membrane filtration, spread plating, and pour plating are conventional methods used to determine the heterotrophic plate counts of water samples. Impedance methods were investigated as an alternative to conventional methods, since sample dilution is not required and the bacterial count can be estimated within 24 h. Comparisons of impedance signals obtained with different water samples revealed that capacitance produced faster detection times than conductance. Moreover, the correlation between heterotrophic plate count and detection time was highest (r = 0.966) when capacitance was used. Linear and quadratic regressions of heterotrophic plate count and impedance detection time were affected by incubation temperatures. Regressions between heterotrophic plate counts based on conventional methods and detection times of water samples incubated at less than or equal to 25 degrees C had R2 values of 0.878 to 0.933. However, regressions using detection times of water samples incubated at greater than or equal to 30 degrees C had lower R2 values, even though water samples produced faster detection times. Comparisons between broth-based versions of R2A medium and plate count agar revealed that the latter correlated highly with heterotrophic plate count, provided that water samples were incubated at 25 degrees C and impedance measurements were conducted with the capacitance signal (r = 0.966). When the linear regression of this relationship was tested with 100 water samples, the correlation between predicted and actual log10 CFU milliliter-1 was 0.869. These results indicate that impedance methods provide a suitable alternative to conventional methods.     

Heterotrophic plate counts of surface water samples by using impedance methods.

Membrane filtration, spread plating, and pour plating are conventional methods used to determine the heterotrophic plate counts of water samples. Impedance methods were investigated as an alternative to conventional methods, since sample dilution is not required and the bacterial count can be estimated within 24 h. Comparisons of impedance signals obtained with different water samples revealed that capacitance produced faster detection times than conductance. Moreover, the correlation between heterotrophic plate count and detection time was highest (r = 0.966) when capacitance was used. Linear and quadratic regressions of heterotrophic plate count and impedance detection time were affected by incubation temperatures. Regressions between heterotrophic plate counts based on conventional methods and detection times of water samples incubated at less than or equal to 25 degrees C had R2 values of 0.878 to 0.933. However, regressions using detection times of water samples incubated at greater than or equal to 30 degrees C had lower R2 values, even though water samples produced faster detection times. Comparisons between broth-based versions of R2A medium and plate count agar revealed that the latter correlated highly with heterotrophic plate count, provided that water samples were incubated at 25 degrees C and impedance measurements were conducted with the capacitance signal (r = 0.966). When the linear regression of this relationship was tested with 100 water samples, the correlation between predicted and actual log10 CFU milliliter-1 was 0.869. These results indicate that impedance methods provide a suitable alternative to conventional methods.     

Electrogenic transport of sodium ions in cytoplasmic and extracellular ion access channels of Na+,K+-ATPase probed by admittance measurement technique

Electrogenic movements of sodium ions in cytoplasmic and extracellular access channel of the Na⁺,K⁺-ATPase have been studied by the admittance measurement technique which allows the detection of small changes of the membrane capacitance and conductance induced by phosphorylation of the ion pump. The measurements were carried out on a model system consisting of a bilayer lipid membrane, to which membrane fragments with ion pumps were adsorbed that contain the ion pumps in high density. Small changes of the membrane capacitance and conductance were induced by a fast release of ATP from caged ATP. The effect was measured at various frequencies and in solutions with different Na⁺ concentrations. The experimentally observed frequency dependences were explained using a theoretical model assuming that Na⁺ movement through the cytoplasmic access channel occurs in one step and through the extracellular access channel, in two steps. The phosphorylation of the protein by ATP leads to a block of the cytoplasmic access channel and an opening the extracellular access channel. The disappearance of electrogenic Na⁺ movements on the cytoplasmic side produces a negative change of capacitance and conductance, while the emergence of extracellular Na⁺ movements generates a positive change. Fitting the experimental dependences of capacitance and conductance by theoretical curves allowed the determination equilibrium and kinetic parameters of sodium transport in the access channels. The text was submitted by the authors in English.     

Kinetics of erythrocyte swelling and membrane hole formation in hypotonic media.

Red blood cell (RBC) swelling and membrane hole formation in hypotonic external media were studied by measuring the time-dependent capacitance, C, and the conductance, G, in the beginning of the beta-dispersion range. At high and moderate osmolarities of the external solution the capacitance reaches a steady-state whereas at low osmolarities it reveals a biphasic kinetics. Examination of RBC suspensions exposed to different concentrations of HgCl(2) demonstrates that water transport through mercury-sensitive water channel controls RBC swelling. Unlike the capacitance, an increase in the conductance to a stationary level is observed after a certain delay. A comparison of G(t) curves recorded for the suspensions of the intact cells and those treated with cytochalasin B or glutaraldehyde demonstrates the significant effect of the membrane viscoelasticity on the pore formation. It is shown that the stretched membrane of completely swollen RBC retains its integrity for a certain time, termed as the membrane lifetime, t(memb). Therefore, the resistivity of RBCs to a certain osmotic shock may be quantified by the distribution function of RBC(t(memb)).     

An electrical method for detecting Listeria spp

A number of selective media for Listeria have been tested for use with electrical methods for growth detection. A modification of an existing medium containing acriflavine, ceftazidime, nalidixic acid and aesculin gave good selectivity and signal response. The capacitance signal was more reliable than conductance and was characteristic of Listeria spp.     

Conductivity and pH dual detection of growth profile of healthy and stressed Listeria monocytogenes

In this study, growth of Listeria monocytogenes in a low conductivity growth medium (LCGM) was simultaneously monitored by conductivity and pH measurements. Detection times obtained from the conductivity and pH growth curves were inversely related to the initial concentration of L. monocytogenes in the medium. Linear responses were found by plotting detection times obtained from both conductivity and pH growth curves as a function of initial cell concentration in the range of 10(2) to 10(7) cfu/mL. The detection time was approximately 12 and 2 h for 10(2) and 10(7) cfu/mL of viable L. monocytogenes, respectively, using the conductivity growth curves, whereas it was approximately 1 h less using the pH growth curves. This dual detection system was used for evaluating the growth of acid-, temperature-, and salt-treated L. monocytogenes in the medium. Acid stress at pH 2 and 3 for 3 h caused approximately 12 and 4 h delay in the detection time on pH growth curves, while stress at pH 5 for 3 h did not cause a significant delay in detection time. Delay in detection times was also observed for L. monocytogenes cells exposed to 45 degrees C for more than 1 h (2 and 6 h). Exposure to 10% NaCl for 3 h did not cause visible delay in the detection time. These observations on detection times for stressed L. monocytogenes had a consistent trend with the cell number decrease determined by surface plating method.     

Exploratory studies of some drug charge transfer interactions

Conductivity and capacitance titrations yield minima for the chlorpromazine hydrochloride-heparin interaction, confirming clinical suspicions of its occurrence. The effective dosage of heparin thus is reduced if administered in conjunction with chlorpromazine. The interaction is interpreted as charge transfer complex formation, occurring as an (electrode) surface reaction. It is suggested that the charge transfer complexing capability of heparin preparations, as evidenced by conductance and/or capacitance changes, evaluated against a well defined donor such as chlorpromazine hydrochloride, may be adapted as a more precise method of measuring heparin activity than coagulation time determinations. Phenytoin and chlorpromazine likewise yield conductance and capacitance minima; voltammetry indicates new peaks at +250mV and −300mV vers.SCE supporting the suggestions that an uncharged 1∶1 complex is being formed, again in a type of surface reaction. Phenytoin and lignocain form a precipitate at 0.002 equimolar; in conductance and capacitance titrations phenytoin behaves as a weak electron donor against iodine though as a weak acceptor against lignocain. Lignocain and chlorpromazine conductance and capacitance titrations using gold electrodes fail to show any evidence for their previously reported interaction on Pt/Pt electrodes. Voltammetry on Pt/Pt electrodes indicates 2 new peaks at zero and at −750mV vers.SCE. It is thought that these two compounds interact only on catalytically highly active surfaces, where they form a weak surface charge transfer complex. Adrenalin, in conductance and capacitance titrations, behaves amphoteric, i.e. as an electron acceptor against the strong donor chlorpromazine and as a donor against the strong acceptor tetramethyl-p-phenylenediamine. Voltammograms of the above listed interactions are interpreted as of the ECE type exhibiting mainly irreversible behaviour.     

Multiplex PCR and a chromogenic DNA macroarray for the detection of Listeria monocytogens, Staphylococcus aureus, Streptococcus agalactiae, Enterobacter sakazakii, Escherichia coli O157:H7, Vibrio parahaemolyticus, Salmonella spp. and Pseudomonas fluorescens in milk and meat samples

Food products, such as milk and meat products including cheese, milk powder, fermented milk, sausage, etc. are susceptible to the contamination by pathogenic and deteriorative bacteria. These bacteria include Listeria monocytogens, Staphylococcus aureus, Enterobacter sakazakii, Escherichia coli O157:H7, Salmonella spp., Vibrio parahaemolyticus, Streptococcus agalactiae and Pseudomonas fluorescens, etc. Traditional methods for the detection of these microorganisms are laborious and time consuming. Therefore, rapid and accurate diagnostic methods are needed. In this study, we designed the DNA probes and PCR primers for the detection of aforementioned microorganisms. By using two sets of multiplex PCR, followed by a chromogenic macroarray system, these organisms in milk or other food products could be simultaneously detected. When the system was used for the inspection of milk or meat homogenate containing 10(0) target cells per milliliter or gram of the sample, all these bacterial species could be identified after an 8h pre-enrichment step. The system consisting of a multiplex PCR step followed by macroarray allowed us to detect multiple target bacterial species simultaneously without the use of agarose gel electrophoresis. Compared to the commonly used multiplex PCR method, this approach has the additional advantage of detecting more bacterial strains because some bacterial strains generate PCR products with the same molecular sizes which can be differentiated by macroarray but not by electrophoresis.     

SIMPLIFIED CAPACITANCE MONITORING FOR THE DETERMINATION OF CAMPYLOBACTER SPP. GROWTH RATES

Capacitance monitoring is commonly used as an efficient means to generate growth curves of bacterial pathogens. However, the use of capacitance monitoring with Campylobacter spp. was previously determined to be difficult due to the complexity of the required media. We investigated capacitance monitoring using a simplified medium for the efficient and reproducible construction of growth curves for Campylobacter spp . It was determined that Campylobacter spp. should initially be propagated on Mueller Hinton plates in a microaerobic atmosphere (5% O₂, 10% CO₂, 85% N₂) at 37C for 24 h, followed by transfer to Mueller Hinton biphasic cultures for 6 h at 37C in a microaerobic atmosphere. Serial dilutions of the Campylobacter spp. cultures should be used for inoculation of Bactometer wells that contain 1 mL Mueller Hinton broth supplemented with 0.1 M sodium pyruvate for the completion of Campylobacter spp. growth curves with the Bactometer.

PRACTICAL APPLICATIONS

Growth rates can vary greatly among Campylobacter isolates; therefore, the rapid and reproducible methods described will prove useful in studies where the generation of growth curves is critical for subsequent experimental analyses.     

Nonculture-based identification of bacteria in milk by protein fingerprinting

Traditional methods for bacterial identification include Gram staining, culturing, and biochemical assays for phenotypic characterization of the causative organism. These methods can be time-consuming because they require in vitro cultivation of the microorganisms. Recently, however, it has become possible to obtain chemical profiles for lipids, peptides, and proteins that are present in an intact organism, particularly now that new developments have been made for the efficient ionization of biomolecules. MS has therefore become the state-of-the-art technology for microorganism identification in microbiological clinical diagnosis. Here, we introduce an innovative sample preparation method for nonculture-based identification of bacteria in milk. The technique detects characteristic profiles of intact proteins (mostly ribosomal) with the recently introduced MALDI Sepsityper(TM) Kit followed by MALDI-MS. In combination with a dedicated bioinformatics software tool for databank matching, the method allows for almost real-time and reliable genus and species identification. We demonstrate the sensitivity of this protocol by experimentally contaminating pasteurized and homogenized whole milk samples with bacterial loads of 10(3) -10(8) colony-forming units (cfu) of laboratory strains of Escherichia coli, Enterococcus faecalis, and Staphylococcus aureus. For milk samples contaminated with a lower bacterial load (10(4) cfu mL(-1) ), bacterial identification could be performed after initial incubation at 37°C for 4 h. The sensitivity of the method may be influenced by the bacterial species and count, and therefore, it must be optimized for the specific application. The proposed use of protein markers for nonculture-based bacterial identification allows for high-throughput detection of pathogens present in milk samples. This method could therefore be useful in the veterinary practice and in the dairy industry, such as for the diagnosis of subclinical mastitis and for the sanitary monitoring of raw and processed milk products.     

The detection of Salmonella enteritidis and S. typhimurium using immunomagnetic separation and conductance microbiology

A rapid method for detection of Salmonella in milk powder is described. The technique involves immunomagnetic separation of Salmonella from pre-enrichment broths using new commercially-available materials, and detection using conductance measurements. Salmonella detection was enhanced by reducing the number and types of competing bacteria present and concentrating the number of Salmonella in the final assay. After a 6 h pre-incubation period Salmonella enteritidis , from an initial inoculum size of 20 cells/ml, were detected in 7.5 h by conductance.