Simultaneous Saccharification and Ethanol Fermentation of Corn Stover at High Temperature and High Solids Loading by a Thermotolerant Strain Saccharomyces cerevisiae DQ1

The thermotolerant strain Saccharomyces cerevisiae DQ1 was applied to the simultaneous saccharification and fermentation (SSF) at high temperature and high solids loading of the dilute acid-pretreated corn stover in the present study. The SSF using S. cerevisiae DQ1 was operated at 30?% solids loading of the pretreated corn stover with three-step SSF mode and achieved up to ethanol titer of 48?g/L and yield of 65.6?%. S. cerevisiae DQ1 showed strong thermotolerance in both the regular one-step SSF and the three-step SSF with changing temperature in each step. The three-step SSF at 40°C using S. cerevisiae DQ1 tolerated the greater cellulase dosage and solids loading of the pretreated corn stover and resulted in increased ethanol production. The present study provided a practical potential for the future SSF of lignocellulose feedstock at high temperature to reach high ethanol titer.     

High titer ethanol production from simultaneous enzymatic saccharification and fermentation of aspen at high solids: a comparison between SPORL and dilute acid pretreatments

Native aspen (Populus tremuloides) was pretreated using sulfuric acid and sodium bisulfite (SPORL) and dilute sulfuric acid alone (DA). Simultaneous enzymatic saccharification and fermentation (SSF) was conducted at 18% solids using commercial enzymes with cellulase loadings ranging from 6 to 15 FPU/g glucan and Saccharomyces cerevisiae Y5. Compared with DA pretreatment, the SPORL pretreatment reduced the energy required for wood chip size-reduction, and reduced mixing energy of the resultant substrate for solid liquefaction. Approximately 60% more ethanol was produced from the solid SPORL substrate (211 L/ton wood at 59 g/L with SSF efficiency of 76%) than from the solid DA substrate (133 L/ton wood at 35 g/L with SSF efficiency 47%) at a cellulase loading of 10 FPU/g glucan after 120 h. When the cellulase loading was increased to 15 FPU/g glucan on the DA substrate, the ethanol yield still remained lower than the SPORL substrate at 10 FPU/g glucan.     

低水用量约束条件下的高固体含量纤维乙醇生物加工技术策略

木质纤维素原料生物转化生产纤维乙醇需要使用大量的水和蒸汽,从而使过程能耗和废水排放显著增加,大幅度增加了加工成本。最大限度地降低水和蒸汽用量对过程节能和废水减排并对最终成本控制极为重要。对极限低水用量约束条件下木质纤维素生物转化关键路径进行了实验研究和计算分析,确定了极低水和蒸汽用量的新型预处理技术,实现高效率预处理过程的废水零排放;采用独特的生物脱毒技术,用从自然界筛选的煤油霉菌Amorphotheca resinae ZN1对预处理原料中的抑制物进行了快速生物脱毒;对极限高固体含量下高粘度多相流物系在复杂抑制物胁迫下的酶水解与发酵行为以及放大准则进行了研究;建立了基于Aspen plus平台上的生物质加工物性数据库和严格热力学意义上的全过程流程模拟数学模型,实现了对过程的局部和全局设计与调优。这一综合技术在生物炼制微型工厂中进行了测试,并在纤维素乙醇工业示范装置中得到了应用。该研究结果将为构建具有工业实用价值的节能和清洁化木质纤维素生物转化技术提供依据。     

Economic impact of total solids loading on enzymatic hydrolysis of dilute acid pretreated corn stover

In process integration studies of the biomass-to-ethanol conversion process, it is necessary to understand how cellulose conversion yields vary as a function of solids and enzyme loading and other key operating variables. The impact of solids loading on enzymatic cellulose hydrolysis of dilute acid pretreated corn stover slurry was determined using an experimental response surface design methodology. From the experimental work, an empirical correlation was obtained that expresses monomeric glucose yield from enzymatic cellulose hydrolysis as a function of solids loading, enzyme loading, and temperature. This correlation was used in a technoeconomic model to study the impact of solids loading on ethanol production economics. The empirical correlation was used to provide a more realistic assessment of process cost by accounting for changes in cellulose conversion yields at different solids and enzyme loadings as well as enzyme cost. As long as enzymatic cellulose conversion drops off at higher total solids loading (due to end-product inhibition or other factors), there is an optimum value for the total solids loading that minimizes the ethanol production cost. The optimum total solids loading shifts to higher values as enzyme cost decreases.     

Simultaneous saccharification and fermentation of Kanlow switchgrass by thermotolerant Kluyveromyces marxianus IMB3: the effect of enzyme loading, temperature and higher solid loadings

Switchgrass (Panicum virgatum) was subjected to hydrothermolysis pretreatment and then used to study the effect of enzyme loading and temperature in a simultaneous saccharification and fermentation (SSF) with the thermotolerant yeast strain Kluyveromyces marxianus IMB3 at 8% solid loading. Various loadings of Accellerase 1500 between 0.1 and 1.1 mL g(-1) glucan were tested in SSF at 45 °C (activity of enzyme was 82.2 FPU mL(-1)). The optimum enzyme loading was 0.7 mL g(-1) glucan based on the six different enzyme loadings tested. SSFs were performed at 37, 41 and 45 °C with an enzyme loading of 0.7 mL g(-1) glucan. The highest ethanol concentration of 22.5 g L(-1) was obtained after 168 h with SSF at 45 °C, which was equivalent to 86% yield. Four different batch and fed-batch strategies were evaluated using a total solid loading of 12% (dry basis). About 32 g L(-1) ethanol was produced with the four strategies, which was equivalent to 82% yield.     

High solid simultaneous saccharification and fermentation of wet oxidized corn stover to ethanol

In this study ethanol was produced from corn stover pretreated by alkaline and acidic wet oxidation (WO) (195 degrees C, 15 min, 12 bar oxygen) followed by nonisothermal simultaneous saccharification and fermentation (SSF). In the first step of the SSF, small amounts of cellulases were added at 50 degrees C, the optimal temperature of enzymes, in order to obtain better mixing condition due to some liquefaction. In the second step more cellulases were added in combination with dried baker's yeast (Saccharomyces cerevisiae) at 30 degrees C. The phenols (0.4-0.5 g/L) and carboxylic acids (4.6-5.9 g/L) were present in the hemicellulose rich hydrolyzate at subinhibitory levels, thus no detoxification was needed prior to SSF of the whole slurry. Based on the cellulose available in the WO corn stover 83% of the theoretical ethanol yield was obtained under optimized SSF conditions. This was achieved with a substrate concentration of 12% dry matter (DM) acidic WO corn stover at 30 FPU/g DM (43.5 FPU/g cellulose) enzyme loading. Even with 20 and 15 FPU/g DM (corresponding to 29 and 22 FPU/g cellulose) enzyme loading, ethanol yields of 76 and 73%, respectively, were obtained. After 120 h of SSF the highest ethanol concentration of 52 g/L (6 vol.%) was achieved, which exceeds the technical and economical limit of the industrial-scale alcohol distillation. The SSF results showed that the cellulose in pretreated corn stover can be efficiently fermented to ethanol with up to 15% DM concentration. A further increase of substrate concentration reduced the ethanol yield significant as a result of insufficient mass transfer. It was also shown that the fermentation could be followed with an easy monitoring system based on the weight loss of the produced CO2.     

Saccharification and fermentation of Sugar Cane bagasse by Klebsiella oxytoca P2 containing chromosomally integrated genes encoding the Zymomonas mobilis ethanol pathway

Pretreatment of sugar cane bagasse is essential for a simultaneous saccharification and fermentation (SSF) process which uses recombinant Klebsiella oxytoca strain P2 and Genencor Spezyme CE. Strain P2 has been genetically engineered to express Zymomonas mobilis genes encoding the ethanol pathway and retains the native ability to transport and metabolize cellobiose (minimizing the need for extracellular cellobiase). In SSF studies with this organism, both the rate of ethanol production and ethanol yield were limited by saccharification at 10 and 20 filter papaer units (FPU) g(-1) acid-treated bagasse. Dilute slurries of biomass were converted to ethanol more efficiently (over 72% of theoretical yield) in simple batch fermentations than slurries containing high solids albeit with the production of lower levels of ethanol. With high solids (i.e., 160 g acid-treated bagasse L(-1)), a combination of 20 FPU cellulase g(-1) bagasse, preincubation under saccharification conditions, and additional grinding (to reduce particle size) were required to produce ca. 40 g ethanol L(-1). Alternatively, almost 40 g ethanol L(-1) was produced with 10 FPU cellulase g(-1) bagasse by incorporating a second saccharification step (no further enzyme addition) followed by a second inoculation and short fermentation. In this way, a theoretical ethanol yield of over 70% was achieved with the production of 20 g ethanol 800 FPU(-1) of commercial cellulase. (c) 1994 John Wiley & Sons, Inc.     

白腐真菌Pleurotus sajor-caju预处理对红麻秸秆发酵乙醇的影响

为研究微生物法预处理对红麻秸秆中木质素的降解及后续的红麻纤维素酶促糖化和发酵效率的影响,将白腐真菌Pleurotus sajor-caju接种在红麻秸秆培养基上固态培养,对红麻秸秆进行预处理。经P. sajor-caju培养25~35 d后,有效转化红麻秸秆中的木质素,转化率最高可达50.20％,并提高红麻纤维素的酶促水解效率,糖化率达69.33％~78.64％,与对照组相比提高了3.5~4.1倍。以微生物法预处理后的红麻秸秆样品为底物的同步糖化发酵实验表明,发酵72 h,发酵液中乙醇浓度达到18.35~     

Ethanol production from paper material using a simultaneous saccharification and fermentation system in a fed-batch basis

In this work, a recycled paper-derived feedstock was used to produce ethanol by the simultaneous saccharification and fermentation (SSF) process using the thermotolerant yeast Kluyveromyces marxianus CECT 10875. At standard SSF conditions, the highest yield (about 80% of theoretical) was obtained at low substrate concentration and high enzyme loading. With increasing substrate concentration, mixing difficulties appeared which prevented an adequate SSF process performance and limited ethanol production. An SSF fed-batch procedure was then used which permitted an increase in substrate concentrations while maintaining SSF yields similar to that obtained at standard SSF, thus allowing an increased final ethanol production (about 18 g/l).     

Considering water availability and the effect of solute concentration on high solids saccharification of lignocellulosic biomass

Milliliter scale (ligno)cellulose saccharifications suggest general solute concentration and its impact on water availability plays a significant role in detrimental effects associated with high solids lignocellulose conversions. A microtumbler developed to enable free‐fall mixing at dry solids loadings up to 35% (w/w) repeatedly produced known detrimental conversion trends on cellulose, xylan and pretreated lignocellulose with commercial enzymes. Despite this, high concentrations of insoluble nonhydrolysable dextrans did not depress saccharification extents in 5% (w/w) cellulose slurries suggesting mass transfer limitations may not significantly limit hydrolysis extents at high solids loadings. Interestingly, cellulose saccharification by purified cellulases showed increased conversions with increasing dry solids loadings. This prompted investigations into impacts the concentration of soluble species, such as sugar alcohols, low molecular weight enzyme preparation components, and monomer hydrolysis products, have on the hydrolysis environment. Such substances significantly depress conversion rates and were shown to correlatively lower water activity (A_w) in the hydrolysis environment while high insoluble solids concentrations did not. Furthermore, low‐field NMR on concentrated slurries of insoluble complex carbohydrates, including the nonhydrolysable dextrans, showed all solids constrained water significantly more than high concentrations of soluble species (inhibitory) suggesting water constraint may not be as problematic an issue at high solids loadings compared to the availability of water in the system. Additionally, the introduction of soluble species lessened overall water constraint in high solids systems and appears to shift the distribution of water away from insoluble surfaces. This is potentially a critical issue for industrial processes operating at high dry solids levels. © 2012 American Institute of Chemical Engineers Biotechnol. Prog., 2012     

Comparative performance of precommercial cellulases hydrolyzing pretreated corn stover

Background

Cellulases and related hydrolytic enzymes represent a key cost factor for biochemical conversion of cellulosic biomass feedstocks to sugars for biofuels and chemicals production. The US Department of Energy (DOE) is cost sharing projects to decrease the cost of enzymes for biomass saccharification. The performance of benchmark cellulase preparations produced by Danisco, DSM, Novozymes and Verenium to convert pretreated corn stover (PCS) cellulose to glucose was evaluated under common experimental conditions and is reported here in a non-attributed manner.

Results

Two hydrolysis modes were examined, enzymatic hydrolysis (EH) of PCS whole slurry or washed PCS solids at pH 5 and 50°C, and simultaneous saccharification and fermentation (SSF) of washed PCS solids at pH 5 and 38°C. Enzymes were dosed on a total protein mass basis, with protein quantified using both the bicinchoninic acid (BCA) assay and the Bradford assay. Substantial differences were observed in absolute cellulose to glucose conversion performance levels under the conditions tested. Higher cellulose conversion yields were obtained using washed solids compared to whole slurry, and estimated enzyme protein dosages required to achieve a particular cellulose conversion to glucose yield were extremely dependent on the protein assay used. All four enzyme systems achieved glucose yields of 90% of theoretical or higher in SSF mode. Glucose yields were reduced in EH mode, with all enzymes achieving glucose yields of at least 85% of theoretical on washed PCS solids and 75% in PCS whole slurry. One of the enzyme systems ('enzyme B') exhibited the best overall performance. However in attaining high conversion yields at lower total enzyme protein loadings, the relative and rank ordered performance of the enzyme systems varied significantly depending upon which hydrolysis mode and protein assay were used as the basis for comparison.

Conclusions

This study provides extensive information about the performance of four precommercial cellulase preparations. Though test conditions were not necessarily optimal for some of the enzymes, all were able to effectively saccharify PCS cellulose. Large differences in the estimated enzyme dosage requirements depending on the assay used to measure protein concentration highlight the need for better consensus methods to quantify enzyme protein.

     

Selective suppression of bacterial contaminants by process conditions during lignocellulose based yeast fermentations

Background

When scaling up lignocellulose-based ethanol production, the desire to increase the final ethanol titer after fermentation can introduce problems. A high concentration of water-insoluble solids (WIS) is needed in the enzymatic hydrolysis step, resulting in increased viscosity, which can cause mass and heat transfer problems because of poor mixing of the material. In the present study, the effects of mixing on the enzymatic hydrolysis of steam-pretreated spruce were investigated using a stirred tank reactor operated with different impeller speeds and enzyme loadings. In addition, the results were related to the power input needed to operate the impeller at different speeds, taking into account the changes in rheology throughout the process.

Results

A marked difference in hydrolysis rate at different impeller speeds was found. For example, the conversion was twice as high after 48 hours at 500 rpm compared with 25 rpm. This difference remained throughout the 96 hours of hydrolysis. Substantial amounts of energy were required to achieve only minor increases in conversion during the later stages of the process.

Conclusions

Impeller speed strongly affected both the hydrolysis rate of the pretreated spruce and needed power input. Similar conversions could be obtained at different energy input by altering the mixing (that is, energy input), enzyme load and residence time, an important issue to consider when designing large-scale plants.     

Liquefaction of lignocellulose at high-solids concentrations

To improve process economics of the lignocellulose to ethanol process a reactor system for enzymatic liquefaction and saccharification at high-solids concentrations was developed. The technology is based on free fall mixing employing a horizontally placed drum with a horizontal rotating shaft mounted with paddlers for mixing. Enzymatic liquefaction and saccharification of pretreated wheat straw was tested with up to 40% (w/w) initial DM. In less than 10 h, the structure of the material was changed from intact straw particles (length 1-5 cm) into a paste/liquid that could be pumped. Tests revealed no significant effect of mixing speed in the range 3.3-11.5 rpm on the glucose conversion after 24 h and ethanol yield after subsequent fermentation for 48 h. Low-power inputs for mixing are therefore possible. Liquefaction and saccharification for 96 h using an enzyme loading of 7 FPU/g.DM and 40% DM resulted in a glucose concentration of 86 g/kg. Experiments conducted at 2%-40% (w/w) initial DM revealed that cellulose and hemicellulose conversion decreased almost linearly with increasing DM. Performing the experiments as simultaneous saccharification and fermentation also revealed a decrease in ethanol yield at increasing initial DM. Saccharomyces cerevisiae was capable of fermenting hydrolysates up to 40% DM. The highest ethanol concentration, 48 g/kg, was obtained using 35% (w/w) DM. Liquefaction of biomass with this reactor system unlocks the possibility of 10% (w/w) ethanol in the fermentation broth in future lignocellulose to ethanol plants.     

Acetic acid-catalyzed hydrothermal pretreatment of corn stover for the production of bioethanol at high-solids content

Corn stover (CS) was hydrothermally pretreated using CH₃COOH (0.3 %, v/v), and subsequently its ability to be utilized for conversion to ethanol at high-solids content was investigated. Pretreatment conditions were optimized employing a response surface methodology (RSM) with temperature and duration as independent variables. Pretreated CS underwent a liquefaction/saccharification step at a custom designed free-fall mixer at 50 °C for either 12 or 24 h using an enzyme loading of 9 mg/g dry matter (DM) at 24 % (w/w) DM. Simultaneous enzymatic saccharification and fermentation (SSF) of liquefacted corn stover resulted in high ethanol concentration (up to 36.8 g/L), with liquefaction duration having a negligible effect. The threshold of ethanol concentration of 4 % (w/w), which is required to reduce the cost of ethanol distillation, was surpassed by the addition of extra enzymes at the start up of SSF achieving this way ethanol titer of 41.5 g/L.     

Dry pretreatment of lignocellulose with extremely low steam and water usage for bioethanol production

Two rarely noticed but important parameters of the dilute sulfuric acid pretreatment of lignocellulose biomass, the feedstock filling ratio to the pretreatment reactor and the solids/liquid presoaking ratio, were extensively studied. The effects of the two parameters on the steam consumption, waste water generation, and pretreatment efficiency were investigated. At the full filling ratio and high solids/liquid presoaking ratio, this “dry” pretreatment method provided at least the following advantages: (1) the steam consumption was significantly reduced; (2) no aqueous acid containing waste water was generated; (3) high solids content of the pretreated materials were obtained and the consequent saccharification and fermentation was carried out at high solids loading easily. This method was applied to various lignocellulose feedstocks successfully and provided a practical means to produce ethanol economically feasible.     

Adaptation of the xylose fermenting yeast <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> F12 for improving ethanol production in different fed-batch SSF processes

An efficient fermenting microorganism for bioethanol production from lignocellulose is highly tolerant to the inhibitors released during pretreatment and is able to ferment efficiently both glucose and xylose. In this study, directed evolution was employed to improve the xylose fermenting Saccharomyces cerevisiae F12 strain for bioethanol production at high substrate loading. Adapted and parental strains were compared with respect to xylose consumption and ethanol production. Adaptation led to an evolved strain more tolerant to the toxic compounds present in the medium. When using concentrated prehydrolysate from steam-pretreated wheat straw with high inhibitor concentration, an improvement of 65 and 20% in xylose consumption and final ethanol concentration, respectively, were achieved using the adapted strain. To address the need of high substrate loadings, fed-batch SSF experiments were performed and an ethanol concentration as high as 27.4 g/l (61% of the theoretical) was obtained with 11.25% (w/w) of water insoluble solids (WIS).     

A comparison between simultaneous saccharification and fermentation and separate hydrolysis and fermentation using steam-pretreated corn stover

Two different process configurations, simultaneous saccharification and fermentation (SSF) and separate hydrolysis and fermentation (SHF), were compared, at 8% water-insoluble solids (WIS), regarding ethanol production from steam-pretreated corn stover. The enzymatic loading in these experiments was 10 FPU/g WIS and the yeast concentration in SSF was 1 g/L (dry weight) of a Saccharomyces cerevisiae strain. When the whole slurry from the pretreatment stage was used as it was, diluted to 8% WIS with water and pH adjusted, SSF gave a 13% higher overall ethanol yield than SHF (72.4% versus 59.1% of the theoretical). The impact of the inhibitory compounds in the liquid fraction of the pretreated slurry was shown to affect SSF and SHF in different ways. The overall ethanol yield (based on the untreated raw material) decreased when SSF was run in absence on inhibitors compared to SSF with inhibitors present. On the contrary, the presence of inhibitors decreased the overall ethanol yield in the case of SHF. However, the SHF yield achieves in the absence of inhibitors was still lower than the SSF yield achieves with inhibitors present.     

Particle concentration and yield stress of biomass slurries during enzymatic hydrolysis at high‐solids loadings

Effective and efficient breakdown of lignocellulosic biomass remains a primary barrier for its use as a feedstock for renewable transportation fuels. A more detailed understanding of the material properties of biomass slurries during conversion is needed to design cost‐effective conversion processes. A series of enzymatic saccharification experiments were performed with dilute acid pretreated corn stover at initial insoluble solids loadings of 20% by mass, during which the concentration of particulate solids and the rheological property yield stress (τ_y) of the slurries were measured. The saccharified stover liquefies to the point of being pourable (τ_y ≤ 10 Pa) at a total biomass conversion of about 40%, after roughly 2 days of saccharification for a moderate loading of enzyme. Mass balance and semi‐empirical relationships are developed to connect the progress of enzymatic hydrolysis with particle concentration and yield stress. The experimental data show good agreement with the proposed relationships. The predictive models developed here are based on established physical principles and should be applicable to the saccharification of other biomass systems. The concepts presented, especially the ability to predict yield stress from extent of conversion, will be helpful in the design and optimization of enzymatic hydrolysis processes that operate at high‐solids loadings. Biotechnol. Bioeng. 2009; 104: 290–300 © 2009 Wiley Periodicals, Inc.     

Improving the fermentation performance of saccharomyces cerevisiae by laccase during ethanol production from steam‐exploded wheat straw at high‐substrate loadings

Operating the saccharification and fermentation processes at high‐substrate loadings is a key factor for making ethanol production from lignocellulosic biomass economically viable. However, increasing the substrate loading presents some disadvantages, including a higher concentration of inhibitors (furan derivatives, weak acids, and phenolic compounds) in the media, which negatively affect the fermentation performance. One strategy to eliminate soluble inhibitors is filtering and washing the pretreated material. In this study, it was observed that even if the material was previously washed, inhibitory compounds were released during the enzymatic hydrolysis step. Laccase enzymatic treatment was evaluated as a method to reduce these inhibitory effects. The laccase efficiency was analyzed in a presaccharification and simultaneous saccharification and fermentation process at high‐substrate loadings. Water‐insoluble solids fraction from steam‐exploded wheat straw was used as substrate and Saccharomyces cerevisiae as fermenting microorganism. Laccase supplementation reduced strongly the phenolic content in the media, without affecting weak acids and furan derivatives. This strategy resulted in an improved yeast performance during simultaneous saccharification and fermentation process, increasing significantly ethanol productivity. © 2012 American Institute of Chemical Engineers Biotechnol. Prog., 2013     

Simultaneous saccharification and fermentation of Kanlow switchgrass pretreated by hydrothermolysis using Kluyveromyces marxianus IMB4

A thermotolerant yeast strain named Kluyveromyces marxianus IMB4 was used in a simultaneous saccharification and fermentation (SSF) process using Kanlow switchgrass as a feedstock. Switchgrass was pretreated using hydrothermolysis at 200 degrees C for 10 min. After pretreatment, insoluble solids were separated from the liquid prehydrolyzate by filtration and washed with deionized water to remove soluble sugars and inhibitors. Insoluble solids were then hydrolyzed using a commercial cellulase preparation and the released glucose was fermented to ethanol by K. marxianus IMB4 in an SSF process. SSF temperature was 37, 41, or 45 degrees C and pH was 4.8 or 5.5. SSF was conducted for 7 days. Results were compared with a control of Saccharomyces cerevisiae D(5)A at 37 degrees C and pH 4.8. Fermentation by IMB4 at 45 and 41 degrees C ceased after 3 and 4 days, respectively, when a pH 4.8 citrate buffer was used. Fermentation continued for all 7 days using IMB4 at 37 degrees C and the control. When pH 5.5 citrate buffer was used, fermentation ceased after 96 h using IMB4 at 45 degrees C, and ethanol yield was greater than when pH 4.8 citrate buffer was used (78% theoretical). Ethanol yield using IMB4 at 45 degrees C, pH 5.5 was greater than the control after 48, 72, and 96 h (P < 0.05).