An ultra scale-down method to investigate monoclonal antibody processing during tangential flow filtration using ultrafiltration membranes

The availability of material for experimental studies is a key constraint in the development of full-scale bioprocesses. This is especially true for the later stages in a bioprocess sequence such as purification and formulation, where the product is at a relatively high concentration and traditional scale-down models can require significant volumes. Using a combination of critical flow regime analysis, bioprocess modelling, and experimentation, ultra scale-down (USD) methods can yield bioprocess information using only millilitre quantities before embarking on highly demanding full-scale studies. In this study the performance of a pilot-scale tangential flow filtration (TFF) system based on a membrane flat-sheet cassette using pumped flow was predicted by devising an USD device comprising a stirred cell using a rotating disc. The USD device operates with just 2.1 cm² of membrane area and, for example, just 1.7 mL of feed for diafiltration studies. The novel features of the design involve optimisation of the disc location and the membrane configuration to yield an approximately uniform shear rate. This is characterised using computational fluid dynamics for a defined layer above the membrane surface. A pilot-scale TFF device operating at ~500-fold larger feed volume and membrane area was characterised in terms of the shear rate derived from flow rate-pressure drop relationships for the cassette. Good agreement was achieved between the USD and TFF devices for the flux and resistance values at equivalent average shear rates for a monoclonal antibody diafiltration stage.     

Cell harvesting by cross-flow microfiltration using a shear-enhanced module

Protein, produced by a bacterial culture of recombinant Vibrio cholerae, was separated from cells in a fermentation broth by cross-flow microfiltration. A new, mechanically agitated (rotational) shear filter, the DMF(TM) filter from Pall, was used to perform the separation. Higher protein recovery and permeate flux than commonly obtained during cell harvesting were demonstrated using sixfold concentration followed by twofold diafiltration. The transmembrane pressure only increased by 10 kPa when the flux was kept constant at 150 L/m(2) h during both concentration and diafiltration. The protein transmission was about 100% initially, and over 90% at the end of the concentration process. The protein transmission during the diafiltration was over 80%. The total recovery of protein was 97%. When using an enzymatic cleaning agent, no significant pure water flux decrease was detected during the course of the experiments. (c) 1996 John Wiley & Sons, Inc.     

Membrane‐Based Approach for the Downstream Processing of Influenza Virus‐Like Particles

Currently, marketed influenza vaccines are only efficient against homologous viruses, thus requiring a seasonal update based on circulating subtypes. This constant reformulation adds several challenges to manufacturing, particularly in purification due to the variation of the physicochemical properties of the vaccine product. A universal platform approach capable of handling such variation is therefore of utmost importance. In this work, a filtration‐based approach is explored to purify influenza virus‐like particles. Switching from adsorptive separation to size‐based purification allows overcoming the differences in retention observed for different influenza strains. The proposed process employs a cascade of ultrafiltration and diafiltration steps, followed by a sterile filtration step. Different process parameters are assessed in terms of product recovery and impurities’ removal. Membrane chemistry, pore size, operation modes, critical flux, transmembrane pressure, and permeate control strategies are evaluated. After membrane selection and parameter optimization, concentration factors and diafiltration volumes are also defined. By optimizing the filtration mode of operation, it is possible to achieve product recoveries of approximately 80%. Overall, the process time is decreased by 30%, its scalability is improved, and the costs are reduced due to the removal of chromatography and associated buffer consumptions, cleaning, and its validation steps.     

Ultra scale‐down approaches for clarification of mammalian cell culture broths in disc‐stack centrifuges

Ultra‐scale down (USD) methodology developed by University College London for cell broth clarification with industrial centrifuges was applied to two common cell lines (NS0 and GS‐CHO) expressing various therapeutic monoclonal antibodies. A number of centrifuges at various scales were used with shear devices operating either by high speed rotation or flow‐through narrow channels. The USD methodology was found effective in accounting for both gravitational and shear effects on clarification performance with three continuous centrifuges at pilot and manufacturing scales. Different shear responses were observed with the two different cell lines and even with the same cell line expressing different products. Separate particle size analysis of the treated broths seems consistent with the shear results. Filterability of the centrifuged solutions was also evaluated to assess the utility of the USD approach for this part of the clarification operation. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

Microfiltration of recombinant yeast cells using a rotating disk dynamic filtration system

To develop a highly efficient cell harvest step under time constraint, a novel rotating disk dynamic filtration system was studied on the laboratory scale (0.147-ft.(2) nylon membrane) for concentrating recombinant yeast cells containing an intracellular product. The existing cross-flow microfiltration method yielded pseudo-steady state flux values below 25 LMH (L/m(2). h) even at low membrane loadings (10 L/ft.(2)). By creating high shear rates (up to 120,000(-1)) on the membrane surface using a rotating solid disk, this dynamic filter has demonstrated dramatically improved performance, presumably due to minimal cake buildup and reduced membrane fouling. Among the many factors investigated, disk rotating speed, which determines shear rates and flow patterns, was found to be the most important adjustable parameter. Our experimental results have shown that the flux increases with disk rotating speed, increases with transmembrane pressure at higher cell concentrations, and can be sustained at high levels under constant flux mode. At a certain membrane loading level, there was a critical speed below which it behaved similarly to a flat sheet system with equivalent shear. Average flux greater than 200 LMH has been demonstrated at 37-L/ft.(2) loading at maximum speed to complete sixfold concentration and 15-volume diafiltration for less than 100 min. An order of magnitude improvement over the crossflow microfiltration control was projected for large scale production. This superior performance, however, would be achieved at the expense of additional power input and heat dissipation, especially when cell concentration reaches above 80 g dry cell weight (DCW)/L. Although a positive linear relationship between power input and dynamic flux at a certain concentration factor has been established, high cell density associated with high viscosity impacted adversely on effective average shear rates and, eventually, severe membrane fouling, rather than cake formation, would limit the performance of this novel system. (c) 1995 John Wiley & Sons, Inc.     

Enzyme recovery during gas/liquid two-phase flow microfiltration of enzyme/yeast mixtures

The effect of a gas/liquid two-phase flow on the recovery of an enzyme was evaluated and compared with standard crossflow operation when confronted with the microfiltration of a high-fouling yeast suspension. Ceramic tubular and flat sheet membranes were used. At constant feed concentration (permeate recycling) and transmembrane pressure, the results obtained with the tubular membrane were dependent on the two-phase flow pattern. In comparison with single-phase flow performances at the same liquid velocity, the enzyme transmission was maintained at a high level with a bubble flow pattern but it decreased by 70% with a slug flow, whatever the flow rate ratio. Identical results were obtained with flat sheet membranes: for the highest flow rate ratio, the enzyme transmission was reduced by 70% even though the permeate flux was improved by 240%. During diafiltration experiments with the tubular membrane, it was found that a bubble flow pattern led to a 13% higher enzyme recovery compared to single-phase flow conditions, whereas with a slug flow the enzyme recovery was strongly reduced. With bubble flow conditions, energy consumption was minimal, confirming that this flow pattern was the most suitable for enzyme recovery.     

Streamlining process characterization efforts using the high throughput ambr® crossflow system for ultrafiltration and diafiltration processing of monoclonal antibodies

Commercial process development for biopharmaceuticals often involves process characterization (PC) studies to gain process knowledge and understanding in preparation for process validation. One common approach to conduct PC activities is by using design-of-experiment, which can help determine the impact process parameter deviations may have on product quality attributes. Qualified scale-down systems are typically used to conduct these studies. For an ultrafiltration/diafiltration (UF/DF) application, however, a traditional scale-down still requires hundreds of milliliters of material per run and can only conduct one experiment at a time. This poses a challenge in resources as there could be 20+ experiments required for a typical UF/DF PC study. One solution to circumvent this is the use of high-throughput systems, which enable parallel experimentation by only using a fraction of the resources. Sartorius Stedim Biotech has recently commercialized the ambr® crossflow high-throughput system to meet this need. In this study, the performance of this system during a monoclonal antibody UF/DF step was first compared with a pilot- and a manufacturing-scale tangential flow filtration (TFF) system at a single operating condition. Due to material limitations, it was then compared to only the pilot-scale TFF system across wider ranges of transmembrane pressure; crossflow rate; and diafiltration concentration in a PC study. Permeate flux, aggregate content, process yield, pH/conductivity traces, retentate concentration, axial pressure drop, and turbidity values were measured at both scales. A good agreement was attained across scales, further supporting its potential use as a scale-down system.     

Evaluation of options for harvest of a recombinant E. Coli fermentation producing a domain antibody using ultra scale‐down techniques and pilot‐scale verification

Ultra scale‐down (USD) methods operating at the millilitre scale were used to characterise full‐scale processing of E. coli fermentation broths autolysed to different extents for release of a domain antibody. The focus was on the primary clarification stages involving continuous centrifugation followed by depth filtration. The performance of this sequence was predicted by USD studies to decrease significantly with increased extents of cell lysis. The use of polyethyleneimine reagent was studied to treat the lysed cell broth by precipitation of soluble contaminants such as DNA and flocculation of cell debris material. The USD studies were used to predict the impact of this treatment on the performance and here it was found that the fermentation could be run to maximum productivity using an acceptable clarification process (e.g., a centrifugation stage operating at 0.11 L/m² equivalent gravity settling area per hour followed by a resultant required depth filter area of 0.07 m²/L supernatant). A range of USD predictions was verified at the pilot scale for centrifugation followed by depth filtration. © 2016 The Authors Biotechnology Progress published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers Biotechnol. Prog., 32:382–392, 2016     

An ultra scale‐down approach to study the interaction of fermentation,homogenization, and centrifugation for antibody fragment recovery from rec E. coli

Escherichia coli is frequently used as a microbial host to express recombinant proteins but it lacks the ability to secrete proteins into medium. One option for protein release is to use high‐pressure homogenization followed by a centrifugation step to remove cell debris. While this does not give selective release of proteins in the periplasmic space, it does provide a robust process. An ultra scale‐down (USD) approach based on focused acoustics is described to study rec E. coli cell disruption by high‐pressure homogenization for recovery of an antibody fragment (Fab′) and the impact of fermentation harvest time. This approach is followed by microwell‐based USD centrifugation to study the removal of the resultant cell debris. Successful verification of this USD approach is achieved using pilot scale high‐pressure homogenization and pilot scale, continuous flow, disc stack centrifugation comparing performance parameters such as the fraction of Fab′ release, cell debris size distribution and the carryover of cell debris fine particles in the supernatant. The integration of fermentation and primary recovery stages is examined using USD monitoring of different phases of cell growth. Increasing susceptibility of the cells to disruption is observed with time following induction. For a given recovery process this results in a higher fraction of product release and a greater proportion of fine cell debris particles that are difficult to remove by centrifugation. Such observations are confirmed at pilot scale. Biotechnol. Bioeng. 2013 9999:XX–XX. © 2013 Wiley Periodicals, Inc. Biotechnol. Bioeng. 2013; 110: 2150–2160. © 2013 Wiley Periodicals, Inc.     

Ultra scale‐down device to predict dewatering levels of solids recovered in a continuous scroll decanter centrifuge

During centrifugation operation, the major challenge in the recovery of extracellular proteins is the removal of the maximum liquid entrapped within the spaces between the settled solids–dewatering level. The ability of the scroll decanter centrifuge (SDC) to process continuously large amounts of feed material with high concentration of solids without the need for resuspension of feeds, and also to achieve relatively high dewatering, could be of great benefit for future use in the biopharmaceutical industry. However, for reliable prediction of dewatering in such a centrifuge, tests using the same kind of equipment at pilot‐scale are required, which are time consuming and costly. To alleviate the need of pilot‐scale trials, a novel USD device, with reduced amounts of feed (2 mL) and to be used in the laboratory, was developed to predict the dewatering levels of a SDC. To verify USD device, dewatering levels achieved were plotted against equivalent compression (Gt_comp) and decanting (Gt_dec) times, obtained from scroll rates and feed flow rates operated at pilot‐scale, respectively. The USD device was able to successfully match dewatering trends of the pilot‐scale as a function of both Gt_comp and Gt_dec, particularly for high cell density feeds, hence accounting for all key variables that influenced dewatering in a SDC. In addition, it accurately mimicked the maximum dewatering performance of the pilot‐scale equipment. Therefore the USD device has the potential to be a useful tool at early stages of process development to gather performance data in the laboratory thus minimizing lengthy and costly runs with pilot‐scale SDC. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 29:1494–1502, 2013     

Protein recovery from cell debris using rotary and tangential crossflow microfiltration

Protein recovery from a bacterial lysate was accomplished using microfiltration membranes in a flat crossflow filter and in a cylindrical rotary filter. Severe membrane fouling yielded relatively low long-term permeate flux values of 10(-4)-10(-3) cm/s (where I cm/s = 3.6 x 10(4) L/m(2) - h). The permeate flux was found to be nearly independent of transmembrane pressure and to increase with increasing shear rate and decreasing solids concentration. The flux increased with shear to approximately the one-third power or greater for the flat filter and the one-half power or greater for the rotary filter; the stronger dependence for the rotary filter is thought to result from Taylor vortices enhancing the back transport of debris carried to the membrane surface by the permeate flow. The average protein transmission or sieving coefficient was measured at approximately 0.6, but considerable scatter in the transmission data was observed. The largest sieving coefficients were obtained for dilute suspensions at high shear rate. The rotary filter provided higher fluxes than did the flat filter for dilute suspensions, but not for concentrated suspensions. (c) 1995 John Wiley & Sons, Inc.     

Purification of a conjugated polysaccharide vaccine using tangential flow diafiltration

Conjugated vaccines prepared from the capsular polysaccharide of Streptococcus pneumoniae can provide immunization against invasive pneumococcal disease, meningitis, and otitis media. One of the critical steps in the production of these vaccines is the removal of free (unreacted) polysaccharides from the protein-polysaccharide conjugate. Experimental studies were performed to evaluate the effects of membrane pore size, filtrate flux, and solution conditions on the transmission of both the conjugate and free polysaccharide through different ultrafiltration membranes. Conjugate purification was done using diafiltration performed in a linearly-scalable tangential flow filtration cassette. More than 98% of the free polysaccharide was removed within a 5-diavolume diafiltration process, which is a significant improvement over previously reported results for purification of similar conjugated vaccines. These results clearly demonstrate the opportunities for using ultrafiltration/diafiltration for the final purification of conjugated vaccine products.     

A scale‐down mimic for mapping the process performance of centrifugation,depth and sterile filtration

In the production of biopharmaceuticals disk‐stack centrifugation is widely used as a harvest step for the removal of cells and cellular debris. Depth filters followed by sterile filters are often then employed to remove residual solids remaining in the centrate. Process development of centrifugation is usually conducted at pilot‐scale so as to mimic the commercial scale equipment but this method requires large quantities of cell culture and significant levels of effort for successful characterization. A scale‐down approach based upon the use of a shear device and a bench‐top centrifuge has been extended in this work towards a preparative methodology that successfully predicts the performance of the continuous centrifuge and polishing filters. The use of this methodology allows the effects of cell culture conditions and large‐scale centrifugal process parameters on subsequent filtration performance to be assessed at an early stage of process development where material availability is limited. Biotechnol. Bioeng. 2016;113: 1934–1941. © 2016 The Authors. Biotechnology and Bioengineering Published by Wiley Periodicals, Inc.     

Lysozyme separation by hollow-fibre ultrafiltration

This paper discusses the purification of lysozyme from chicken egg white using hollow-fibre ultrafiltration (30kDa MWCO, polysulphone membrane). Lysozyme is preferentially transmitted through the membrane while the membrane largely retains other egg white proteins. Improvement in system hydrodynamics resulted in an increase in permeate flux while lysozyme transmission remained unaffected, leading to higher productivity. The percentage purity of lysozyme obtained was generally insensitive to system hydrodynamics. The permeate flux and productivity increased with increase in transmembrane pressure (TMP) before levelling off around 0.7bar. However, the TMP did not have any pronounced effect on the transmission and the purity of lysozyme. Experiments carried out in the diafiltration mode showed that moderately pure lysozyme (80-90%) could be obtained in an extended operation.     

Environmental Assessment of Refuse‐Derived Fuel Co‐Combustion in a Coal‐Fired Power Plant

Municipal residual waste (RW) produced in the Venice area undergoes mechanical‐biological treatment (MBT) in the Fusina plant to produce refuse‐derived fuel (RDF) that is then co‐combusted in a nearby coal‐fired power station. Being the first significant project for RDF co‐firing in power plants in Italy, a number of different testing phases were performed starting in 2003, aimed at evaluating differences between so‐called blank operation (i.e., with only coal feeding) and RDF co‐firing at different feeding rates. The analysis of data gathered during the industrial experimentation shows a savings of 0.7 tonnes (t) of coal per each tonne of co‐fired RDF; stack concentrations of some pollutants (hydrochloric acid [HCl], ammonia [NH₃], carbon monoxide [CO], chromium [Cr], and lead [Pb]) appear slightly higher during co‐combustion compared with blank operation, whereas concentrations of dust, sulfur oxides (SOx), and some metals (manganese [Mn], nickel [Ni], vanadium [V]) are lower. To assess the overall environmental performance of this practice, a life cycle assessment (LCA) study was then performed, where different strategies of energy recovery from RW were compared: production of RDF and its co‐combustion in the Fusina power plant, RW combustion without any pretreatment in a mass‐burn waste‐to‐energy (WTE) plant, and production of RDF and its combustion in a dedicated WTE plant. The LCA results show that co‐combustion of RDF performs better than the other strategies for all impact categories evaluated. The only exception is when the WTE plant operates in combined heat and power mode, with very high overall conversion efficiencies.     

An ultra scale‐down characterization of low shear stress primary recovery stages to enhance selectivity of fusion protein recovery from its molecular variants

Fusion proteins offer the prospect of new therapeutic products with multiple functions. The primary recovery is investigated of a fusion protein consisting of modified E2 protein from hepatitis C virus fused to human IgG1 Fc and expressed in a Chinese hamster ovary (CHO) cell line. Fusion protein products inevitably pose increased challenge in preparation and purification. Of particular concerns are: (i) the impact of shear stress on product integrity and (ii) the presence of product‐related contaminants which could prove challenging to remove during the high resolution purification steps. This paper addresses the use of microwell‐based ultra scale‐down (USD) methods to develop a bioprocess strategy focused on the integration of cell culture and cell removal operations and where the focus is on the use of operations which impart low shear stress levels even when applied at eventual manufacturing scale. An USD shear device was used to demonstrate that cells exposed to high process stresses such as those that occur in the feed zone of a continuous non‐hermetic centrifuge resulted in the reduction of the fusion protein and also the release of glycosylated intracellular variants. In addition, extended cell culture resulted in release of such variants. USD mimics of low shear stress, hydrohermetic feed zone centrifugation and of depth filtration were used to demonstrate little to no release during recovery of these variants with both results verified at pilot scale. Furthermore, the USD studies were used to predict removal of contaminants such as lipids, nucleic acids, and cell debris with, for example, depth filtration delivering greater removal than for centrifugation but a small (～10%) decrease in yield of the fusion protein. These USD observations of product recovery and carryover of contaminants were also confirmed at pilot scale as was also the capacity or throughput achievable for continuous centrifugation or for depth filtration. The advantages are discussed of operating a lower yield cell culture and a low shear stress recovery process in return for a considerably less challenging purification demand. Biotechnol. Bioeng. 2013; 110: 1973–1983. © 2013 Wiley Periodicals, Inc.     

Ultra scale‐down prediction using microwell technology of the industrial scale clarification characteristics by centrifugation of mammalian cell broths

This article describes how a combination of an ultra scale‐down (USD) shear device feeding a microwell centrifugation plate may be used to provide a prediction of how mammalian cell broth will clarify at scale. In particular a method is described that is inherently adaptable to a robotic platform and may be used to predict how the flow rate and capacity (equivalent settling area) of a centrifuge and the choice of feed zone configuration may affect the solids carry over in the supernatant. This is an important consideration as the extent of solids carry over will determine the required size and lifetime of a subsequent filtration stage or the passage of fine particulates and colloidal material affecting the performance and lifetime of chromatography stages. The extent of solids removal observed in individual wells of a microwell plate during centrifugation is shown to correlate with the vertical and horizontal location of the well on the plate. Geometric adjustments to the evaluation of the equivalent settling area of individual wells (Σ_M) results in an improved prediction of solids removal as a function of centrifuge capacity. The USD centrifuge settling characteristics need to be as for a range of equivalent flow rates as may be experienced at an industrial scale for a machine of different shear characteristics in the entry feed zone. This was shown to be achievable with two microwell‐plate based measurements and the use of varying fill volumes in the microwells to allow the rapid study of a fivefold range of equivalent flow rates (i.e., at full scale for a particular industrial centrifuge) and the effect of a range of feed configurations. The microwell based USD method was used to examine the recovery of CHO‐S cells, prepared in a 5 L reactor, at different points of growth and for different levels of exposure to shear post reactor. The combination of particle size distribution measurements of the cells before and after shear and the effect of shear on the solids remaining after centrifugation rate provide insight into the state of the cells throughout the fermentation and the ease with which they and accumulated debris may be removed by continuous centrifugation. Hence bioprocess data are more readily available to help better integrate cell culture and cell removal stages and resolve key bioprocess design issues such as choice of time of harvesting and the impact on product yield and contaminant carry over. Operation at microwell scale allows data acquisition and bioprocess understanding over a wide range of operating conditions that might not normally be achieved during bioprocess development. Biotechnol. Bioeng. 2009; 104: 321–331 © 2009 Wiley Periodicals, Inc.     

A multi‐dimensional approach for fractionating proteins using charged membranes

In an effort to increase selectivity among proteins with crossflow ultrafiltration, we offer and demonstrate a comprehensive approach to fractionate proteins of similar molecular weight and relatively close pI values. This multidimensional approach involves optimizing membrane charge type and density together with operating conditions such as precise control of pH, ionic strength, and transmembrane pressure for reduced membrane fouling. Each filtration experiment was performed in cross‐flow configuration for ～20 min, allowing fast screening for optimal separation as determined by maximum selectivity, Ψ, and purity, P. Using our comprehensive approach for fractionating mixtures RNase A–lysozyme and BSA–hemoglobin, we obtained values of Ψ = 9.1, P = 95.7%, and Ψ = 6.5, P = 62.1%, respectively. Biotechnol. Bioeng. 2013; 110: 1704–1713. © 2013 Wiley Periodicals, Inc.     

A new coiled hollow-fiber module design for enhanced microfiltration performance in biotechnology.

The microfiltration performance of a novel membrane module design with helically wound hollow fibers is compared with that obtained with a standard commercial-type crossflow module containing linear hollow fibers. Cell suspensions (yeast, E. coli, and mammalian cell cultures) commonly clarified in the biotechnology industry are used for this comparison. The effect of variables such as transmembrane pressure, particle suspension concentration, and feed flow rate on membrane performance is evaluated. Normalized permeation fluxes versus flow rate or Dean number behave according to a heat transfer correlation obtained with centrifugal instabilities of the Taylor type. The microfiltration performance of this new module design, which uses secondary flows in helical tubes, is significantly better than an equivalent current commercial crossflow module when filtering suspensions relevant to the biotechnology industry. Flux and capacity improvements of up to 3.2-fold (constant transmembrane pressure operation) and 3.9-fold (constant flux operation), respectively, were obtained with the helical module over those for the linear module.     

Semisynthesis and optimization of G protein‐coupled receptor mimics

We have recently developed a soluble mimic of the corticotropin‐releasing factor receptor type 1 (CRF1), a membrane‐spanning G protein‐coupled receptor, which allowed investigations on receptor–ligand interactions. The CRF1 mimic consists of the receptor N‐terminus and three synthetic extracellular loops (ECL1–3), which constitute the extracellular receptor domains (ECDs) of CRF1, coupled to a linear peptide template. Here, we report the synthesis of a modified CRF1 mimic, which is more similar to the native receptor possessing a cyclic template that displays the ECDs in a more physiological conformation compared with the initial linear design. In order to facilitate detailed biophysical investigations on CRF1 mimics, we have further established a cost‐efficient access to the CRF1 mimic, which is suitable for isotopic labeling for NMR spectroscopy. To this end, the loop‐mimicking cyclic peptide of the ECL2 of CRF1 was produced recombinantly and cyclized by expressed protein ligation. Cyclic ECL2 was obtained in milligram scale, and CRF1 mimics synthesized from this material displayed the same binding properties as synthetic CRF1 constructs. Copyright © 2014 European Peptide Society and John Wiley & Sons, Ltd.