Removal of peroxides in polyethylene glycols by vacuum drying: Implications in the stability of biotech and pharmaceutical formulations

The purpose of this study was to investigate the utility of vacuum drying for removing peroxides from polyethylene glycols (PEGs). PEG solutions (PEG 1450 and PEG 20000) containing varying levels of peroxides were prepared by storing under different light and temperature conditions. PEGs containing low and high levels of peroxides were vacuum dried from dilute and concentrated solutions (2.5%, 7.5%, 15%, and 50% wt/vol of PEG 1450 and 2.5%, 7.5%, 15%, and 25% wt/vol of PEG 20000). Ferrous ion oxidation in presence of ferric ion indicator xylenol orange (FOX) colorimetric assay was used to determine the concentration of peroxides. Peroxide content in PEGs increased upon storage. The increase was more pronounced when PEGs were stored at higher temperatures and exposed to light. Vacuum drying at 0.1 mm Hg for 48 hours at 25°C resulted in greater than 90% decrease in the level of peroxides in all cases except when high peroxide containing 25% wt/vol solution of PEG 20000 or 50% wt/vol solution of PEG 1450 were dried. The reduction in the level of peroxides for PEGs dried from high peroxide containing 25% wt/vol solution of PEG 2000 and 50% wt/vol solution of PEG 1450 was found to be 88% and 52%, respectively. Oxidation of methionine in Met-Leu-Phe peptide was significantly reduced when vacuum-dried PEGs were used. Vacuum drying PEG solutions at low pressures is an effective method for the removal of the residual peroxides present in commercially available PEGs. Published: July 28, 2006     

Glyceride lipases in nerve endings of guinea-pig brain and their stimulation by noradrenaline, 5-hydroxytryptamine and adrenaline

1. Combined guinea-pig cortex and cerebellum was shown to contain triglyceride lipase, diglyceride lipase and monoglyceride lipase, which were assayed by the release of [1-(14)C]palmitate from [1-(14)C]palmitoylglycerol esters. Triglyceride lipase and diglyceride lipase were found in all particulate fractions. 2. With osmotically ruptured synaptosomes the rates of release of palmitate from glyceryl tripalmitate and glyceryl dipalmitate were 7-25mumol/h per g of protein and 0.18-0.69mmol/h per g of protein respectively. The logarithm of the rate of hydrolysis of glyceryl monopalmitate increased linearly with the logarithm of protein concentration. The pH optima of triglyceride lipase and diglyceride lipase were between 7 and 8. The pH optimum for monoglyceride lipase was approx. 8. 3. Triglyceride lipase and diglyceride lipase of osmotically ruptured synaptosomes were stimulated by noradrenaline, 5-hydroxytryptamine and adrenaline. Triglyceride lipase of isolated synaptic membranes was stimulated by 0.01-1mm-noradrenaline. Aging of membranes at 0 degrees C decreased activity, which could still be stimulated by noradrenaline. Diglyceride lipase of isolated membranes was stimulated by 1mum-1mm-noradrenaline. The activity of triglyceride lipase in isolated synaptic vesicles was diminished by 1mm-5-hydroxytryptamine.     

Preparation of resealed pig lymphocyte plasma-membrane vesicles.

Pig lymphocyte plasma-membrane vesicles that are impermeable to large molecules were prepared by means of centrifugation on a continuous dextran gradient. They were isolated in a yield of 60--80% of the total plasma membrane recovered, and were characterized as being impermeable to macromolecules by their exclusion of inulin (mol.wt. 5200) and Dextran T10 (mol.wt. 10 000).     

pH-Sensitive hydrogels as gastrointestinal tract absorption enhancers: transport mechanisms of salmon calcitonin and other model molecules using the Caco-2 cell model

The main interest of this work was the investigation of the transport mechanisms of salmon calcitonin through the epithelial cell monolayer in the presence and absence of pH-sensitive hydrogel nanospheres composed of poly(methacrylic acid-grafted-poly(ethylene glycol)) (PMAA-g-EG). For this purpose, a gastrointestinal cell culture model, the Caco-2 cell line, was employed. The transport of other macromolecules such as fluorescein sodium, fluorescein isothiocyanate dextran, and (14)C-mannitol were also investigated and compared. Transport experiments were conducted in the apical-to-basolateral direction at 37 and 5 degrees C and from the basolateral-to-apical direction at 37 degrees C. Results revealed that the presence of P(MAA-g-EG) nanospheres increased the transport of paracellularly transported molecules such as (14)C-mannitol and fluorescein isothiocyanate dextran when compared to controls. Fluorescein sodium salt solutions were investigated as an actively transported molecule. The transport of fluorescein was affected by the concentration of PEG chains in the structure. Salmon calcitonin transport was enhanced in the presence of the nanospheres. The comparison of the transport behavior of dextran and calcitonin revealed that the main transport mechanism for salmon calcitonin through epithelial cell monolayers is predominantly paracellular.     

Stereospecific D-glucose transport in mixed membrane and plasma membrane vesicles derived from cultured chick embryo fibroblasts

Mixed membrane vesicles prepared from cultured chick embryo fibroblasts possess a stereospecific D-glucose transport system, the properties of which are identical to those of the system in intact cells. Uptake of D-glucose proceeds without chemical alteration. The rate of stereospecific uptake of D-glucose into the mixed vesicles is 70% greater than that of the homogenate and uptake is directly proportional to membrane protein concentration. Stereospecific D-glucose uptake appears linear for 0.3 min, reaches a maximum at 2--5 min, and declines to zero by 5 h as L-glucose enters the vesicles. Uptake is osmotically sensitive and inhibited by cytochalasin B (Ki = 0.13 microM) and the structural analogues of D-glucose : D-mannose, 2-deoxy-D-glucose, 3-O-methyl-D-glucose, D-galactose and maltose, but not by sucrose of L-glucose. Uphill counterflow can be demonstrated and the apparent activation energy displays a transition from 47.7 kcal/mol below 11 degrees C to 18.1 kcal/mol above 11 degrees C. Stereospecific uptake rates of mixed vesicles prepared from Rous sarcoma virus-transformed cells are increased 30% over control values, and are increased 66% in vesicles derived from cells incubated for 24 h in glucose-free medium. Plasma membrane vesicles prepared from these cells by a dextran cushion centrifugation procedure display a 9-fold increase in the specific activity of stereospecific D-glucose uptake relative to the homogenate. Extraction of these membranes with dimethylmaleic anhydride (5 mg/mg protein) results in substantial or complete removal of major polypeptides of molecular weight 40 000, 55 000, 75 000, 78 000 and 200 000 with no loss in total uptake activity. Following extraction, major polypeptides of molecular weight 28 000, 33 000 and 68 000 remain in the membrane residue.     

Effects of additives on the thermostability of chloroperoxidase

The effects of several polyhydroxy compounds (glucose, fructose, gumsugar, galactose, trehalose, dextran, xylose, PEG200, glycerin) and surfactant (dioctyl sulfosuccinate sodium salt, AOT) on the catalytic activity and thermal stability of chloroperoxidase (CPO) in aqueous systems were investigated at various temperatures. A 25% superactivity was found in AOT solutions at 25 degrees C, and it could be maintained during the 882 h. PEG200 and glycerin were proven to be the most efficient stabilizer for CPO in temperatures ranging from 25 to 60 degrees C. Trehalose is more helpful than other sugars for extended storage of CPO. These results are promising in view of industrial applications of this versatile biological catalyst. The protective mechanism of various additives on CPO was discussed.     

Estimation of the percolation thresholds in lobenzarit disodium native dextran matrix tablets

The objective of the present work is to estimate for the first time the percolation threshold of a new series of dextran (native dextran of high molecular weight [B110-1-2, Mw = 2 x 10(6)]), in matrices of lobenzarit disodium (LBD) and to apply the obtained result to the design of hydrophilic matrices for the controlled delivery of this drug. The formulations studied were prepared with different amounts of excipient in the range of 20% to 70% wt/wt. Dissolution studies were performed using the paddle method (100 rpm) and one face water uptake measurements were performed using a modified Enslin apparatus. The Higuchi, zero-order, and Hixson-Crowell models as well as the nonlinear regression model were employed as empiric methods to study the release data. Values of diffusion exponent 0.563 < n < 0.786 (Korsmeyer equation) for dissolution profile and water uptake mechanism 0.715 < n < 1 (Davidson and Peppas equation) suggested anomalous or complex mechanisms. On the other hand, the contribution of the relaxation or erosion and of the diffusive mechanism in Peppas-Sahlin equation indicated that the main mechanism for drug delivery from tablets is swelling controlled delivery (K(r)/K(d) < 1). The critical points observed in kinetic parameters above 58.63% vol/vol of native dextran B110-1-2 plus initial porosity in the LBD-dextran matrices with a relative polymer/drug particle size of 4.17 were attributed to the existence of an excipient percolation threshold.     

Eudragit-coated pectin microspheres of 5-fluorouracil for colon targeting

An objective of the present investigation was to prepare and evaluate Eudragit-coated pectin microspheres for colon targeting of 5-fluorouracil (FU). Pectin microspheres were prepared by emulsion dehydration method using different ratios of FU and pectin (1:3 to 1:6), stirring speeds (500–2000 rpm) and emulsifier concentrations (0.75%–1.5% wt/vol). The yield of preparation and the encapsulation efficiencies were high for all pectin microspheres. Microspheres prepared by using drug:polymer ratio 1:4, stirring speed 1000 rpm, and 1.25% wt/vol concentration of emulsifying agent were selected as an optimized formulation. Eudragit-coating of pectin microspheres was performed by oil-in-oil solvent evaporation method using coat: core ratio (5:1). Pectin microspheres and Eudragit-coated pectin microspheres were evaluated for surface morphology, particle size and size distribution, swellability, percentage drug entrapment, and in vitro drug release in simulated gastrointestinal fluids (SGF). The in vitro drug release study of optimized formulation was also performed in simulated colonic fluid in the presence of 2% rat cecal content. Organ distribution study in albino rats was performed to establish the targeting potential of optimized formulation in the colon. The release profile of FU from Eudragit-coated pectin microspheres was pH dependent. In acidic medium, the release rate was much slower; however, the drug was released quickly at pH 7.4. It is concluded from the present investigation that Eudragit-coated pectin microspheres are promising controlled release carriers for colon-targeted delivery of FU. Published: February 16, 2007     

Stabilization of dextransucrase from Leuconostoc mesenteroides NRRL B-512F by nonionic detergents, poly(ethylene glycol) and high-molecular-weight dextran

Dextransucrase (sucrose: 1,6-alpha-D-glucan 6-alpha-D-glucosyltransferase, EC 2.4.1.5) (3 IU/ml culture supernatant) was obtained by a modification of the method of Robyt and Walseth (Robyt, J.F. and Walseth, T.F. (1979) Carbohydr. Res. 68, 95-111) from a nitrosoguanidine mutant of Leuconostoc mesenteroides NRRL B-512F selected for high dextransucrase production. Dialyzed, concentrated culture supernatant (crude enzyme) was treated with immobilized dextranase (EC 3.2.1.11) and chromatographed on a column of Bio-Gel A-5m. The resulting, purified enzyme lost activity rapidly at 25 degrees C or on manipulation, as did the crude enzyme when diluted below 1 U/ml. Both enzyme preparations could be stabilized by low levels of high-molecular-weight dextran (2 micrograms/ml), poly(ethylene glycol) (e.g., 10 micrograms/ml PEG 20 000), or nonionic detergents (e.g., 10 micrograms/ml Tween 80). The stabilizing capacity of poly(ethylene glycol) and of dextran increased with molecular weight. Calcium had no stabilizing action in the absence of other additions, but reduced the inactivation that occurred in the presence of 0.5% bovine serum albumin or high concentrations (greater than 0.1%) of Triton X-100. In summary, dextransucrase could be stabilized against activity losses caused by heating or by dilution through the addition of low concentrations of nonionic polymers (dextran, PEG 20000, methyl cellulose) or of nonionic detergents at or slightly below their critical micelle concentrations.     

O2-binding albumin thin films: solid membranes of poly(ethylene glycol)-conjugated human serum albumin incorporating iron porphyrin

Poly(ethylene glycol) (PEG)-conjugated human serum albumin (HSA) incorporating the tetrakis(alpha,alpha,alpha,alpha-o-amidophenyl)porphinatoiron(II) derivative (FeP) [PEG(HSA-FeP)] is a unique plasma protein-based O2 carrier as a red blood cell substitute. The aqueous solution of PEG(HSA-FeP) [mw of PEG: 2-kDa (PEG2) or 5-kDa (PEG5)] was evaporated on a glass surface to produce a red-colored solid membrane. Scanning electron microscopy observations revealed that the PEG2(HSA-FeP) membrane consisted of two parts: (i) a surface layer made of a fibrous component (10 microm thickness), and (ii) a bottom layer of an amorphous phase (5 microm thickness). The condensed solution provided a thick membrane (70 microm), which also has the amorphous bottom layer. On the other hand, the PEG5(HSA-FeP) produced homogeneous membrane made of the fibrous component. The FeP active sites in the solid membrane formed very stable O2-adduct complexes at 37 degrees C with a half-lifetime of 40 h. The O2-binding affinity of the PEG2(HSA-FeP) membrane (P1/2 = 40 Torr, 25 degrees C) was 4-fold lower than that in aqueous solution, which is kinetically due to the low association rate constant. The membrane was soluble again in water and organic solvents (ethanol and chloroform) without deformation of the secondary structure of the protein. The addition of hyaluronic acid gave a free-standing flexible thin film, and it can also bind and release O2 as well. These O2-carrying albumin membranes with a micrometer-thickness would be of significant medical importance for a variety of clinical treatments.     

Translocation of phospholipase A2 from cytosol to membranes in rat brain induced by calcium ions

Phospholipase A2 (PLA2) activities were found in the cytosolic fractions of rat brain. Using the gel filtration chromatography, two major peaks of PLA2 activities were demonstrated: PLA2-H (200-500 kDa) and PLA2-L (100 kDa). PLA2-L was active at both neutral and alkaline pH and absolutely required Ca2+ for the activity, while the activity of PLA2-H was detected only at alkaline pH and independent of Ca2+. The activation of PLA2-L by Ca2+ was biphasic; the first observed at 1-100 microM Ca2+ and the second at 10 mM Ca2+. In the reconstitution system of partially purified PLA2-L and synaptosomal membranes from rat brain, PLA2-L associated with the membranes in a Ca2(+)-dependent manner. The association was completed within 5-10 min at 25 degrees C both at 10 microM and 1 mM Ca2+, though amount of PLA2-L translocated was dependent on Ca2+ concentrations. These results suggest that Ca2+ promotes the translocation of the cytosolic PLA2-L to membranes where phospholipids, substrate of PLA2, are present.     

Fusion of Madin-Darby canine kidney cells by HVJ (Sendai virus): absence of direct association of virus particles with the site of membrane fusion

The process of cell fusion of Madin-Darby canine kidney (MDCK) cells by HVJ (Sendai virus) was investigated to determine whether the HVJ particles were directly associated with the site of membrane fusion. Confluent monolayer cultures of MDCK cells are sealed together by tight junctions on the apices of their lateral membranes, so added virus particles can be adsorbed only to the apical surfaces of the cells. After incubation with HVJ at 37 degrees C for 30 min, the cells still appeared mononucleate and unfused by light microscopy, but electron microscopic examination showed that fusion at the lateral membranes had occurred below the tight junctions. Furthermore, when fluorescein isothiocyanate (FITC)-labeled macromolecules, which cannot pass across the gap junctions, were injected into the cells at this stage, labeled macromolecules were found to diffuse into the adjacent cells. These findings strongly suggest that cell fusion was initiated in the lateral membrane, a region distinct from the site of adsorbed HVJ particles. Thus, the virus particles were not directly associated with the fusion site, but induced fusion of the lateral membranes indirectly.     

Aqueous two-phase systems containing urea: influence on phase separation and stabilization of protein conformation by phase components.

During recombinant Escherichia coli fermentation with high expression levels, inclusion bodies are often formed. Aqueous two-phase systems have been used in the presence of urea for the initial recovery steps. To investigate phase behavior of such systems we determined phase diagrams of poly(ethylene glycol) (PEG)/sodium sulfate/urea/water and PEG/dextran T-500 (DEX)/urea/phosphate buffer/water at different concentrations of urea and different molecular weight of PEG. PEG/Na2SO4 aqueous two-phase systems could be obtained including up to 30% w/w urea at 25 degrees C and PEG/dextran T-500 up to 35% w/w urea. The binodial was displaced toward higher concentrations with increasing urea concentrations. The partition coefficient of urea was near unity. An unstable mutant of T4-lysozyme with an amino acid replacement in the core (V149T) was used to analyze the effect of phase components on the conformation of the enzyme. We showed that partitioning of tryptophan was not dependent on the concentration of urea in the phase system.     

Formulation and evaluation of anticancer and antiangiogenesis efficiency of PLA–PEG nanoparticles loaded with galbanic acid in C26 colon carcinoma,in vitro and in vivo

Galbanic acid (GBA) is an active sesquiterpene coumarin derivative, with various medicinal benefits, including anticancer properties. However, the low solubility of GBA is the main limitation of its clinical applications. In this study, we used a nanosystem based on poly (D, l -lactide)–polyethylene glycol (PLA–PEG), for the delivery of GBA to C26 colon carcinoma cells. The physicochemical characteristics of nanoparticles (NPs) prepared by the emulsification–evaporation method were evaluated. MTT assay was used to compare the anticell proliferation of GBA and PLA–PEG–GBA against C26 cell lines. PLA–PEG-NPs with an average size of about 140 nm had an enhanced release of GBA at a pH of 5.5 compared with a pH of 7.4. Cytotoxicity studies showed that the IC ₅₀ of the PLA–PEG–GBA NPs (8 µM) was significantly lower than free GBA (15 µM). In the in vivo study, PLA–PEG–GBA NPs exhibited remarkable efficacy and reduced in vivo toxicity in C26 colon carcinoma tumor-bearing female BALB/c mice. To study the antiangiogenesis effect of the NPs, tumor sections were stained with an anti CD34 antibody. The results show the CD34 (+) vessels were decreased in the GBA and PLA–PEG–GBA treated mice by more than 75% and 90%, respectively. These results suggest that the encapsulation of GBA into the PLA–PEG could potentially be used for the treatment of colorectal cancer.     

In-situ formation of biodegradable hydrogels by stereocomplexation of PEG-(PLLA)8 and PEG-(PDLA)8 star block copolymers

Eight-arm poly(ethylene glycol)-poly(L-lactide), PEG-(PLLA)(8), and poly(ethylene glycol)-poly(D-lactide), PEG-(PDLA)(8), star block copolymers were synthesized by ring-opening polymerization of either L-lactide or D-lactide at room temperature in the presence of a single-site ethylzinc complex and 8-arm PEG (M(n) = 21.8 x 10(3) or 43.5 x 10(3)) as a catalyst and initiator, respectively. High lactide conversions (>95%) and well-defined copolymers with PLLA or PDLA blocks of the desired molecular weights were obtained. Star block copolymers were water-soluble when the number of lactyl units per poly(lactide) (PLA) block did not exceed 14 and 17 for PEG21800-(PLA)(8) and PEG43500-(PLA)(8), respectively. PEG-(PLA)(8) stereocomplexed hydrogels were prepared by mixing aqueous solutions with equimolar amounts of PEG-(PLLA)(8) and PEG-(PDLA)(8) in a polymer concentration range of 5-25 w/v % for PEG21800-(PLA)(8) star block copolymers and of 6-8 w/v % for PEG43500-(PLA)(8) star block copolymers. The gelation is driven by stereocomplexation of the PLLA and PDLA blocks, as confirmed by wide-angle X-ray scattering experiments. The stereocomplexed hydrogels were stable in a range from 10 to 70 degrees C, depending on their aqueous concentration and the PLA block length. Stereocomplexed hydrogels at 10 w/v % polymer concentration showed larger hydrophilic and hydrophobic domains as compared to 10 w/v % single enantiomer solutions, as determined by cryo-TEM. Correspondingly, dynamic light scattering showed that 1 w/v % solutions containing both PEG-(PLLA)(8) and PEG-(PDLA)(8) have larger "micelles" as compared to 1 w/v % single enantiomer solutions. With increasing polymer concentration and PLLA and PDLA block length, the storage modulus of the stereocomplexed hydrogels increases and the gelation time decreases. Stereocomplexed hydrogels with high storage moduli (up to 14 kPa) could be obtained at 37 degrees C in PBS. These stereocomplexed hydrogels are promising for use in biomedical applications, including drug delivery and tissue engineering, because they are biodegradable and the in-situ formation allows for easy immobilization of drugs and cells.     

Structure and morphology changes during in vitro degradation of electrospun poly(glycolide-co-lactide) nanofiber membrane

Electrospun poly(glycolide-co-lactide) (PLA10GA90, LA/GA ratio 10/90) biodegradable nanofiber membranes possessed very high surface area to volume ratios and were completely noncrystalline with a relatively lowered glass transition temperature. These characteristics led to very different structure, morphology, and property changes during in vitro degradation, which were examined systematically. A shrinkage study showed that the electrospun crystallizable but amorphous PLA10GA90 membranes exhibited a very small shrinkage percentage when compared with the electrospun membranes of noncrystallizable poly(lactide-co-glycolide) (PLA75GA25, LA/GA 75/25) and poly(d,l-lactide). Although the weight loss of electrospun PLA10GA90 membranes exhibited a similar degradation behavior as cast thin films, detailed studies showed that the structure and morphology changes in electrospun membranes followed different pathways during the hydrolytic degradation. After 1 day of degradation in buffer solution at 37 degrees C, electrospun PLA10GA90 membranes exhibited a sudden increase in crystallinity and glass transition temperature, due to the fast thermally induced crystallization process. The continuous increase in crystallinity and apparent crystal size, as well as the decrease in long period and lamellae thickness, indicated that the thermally induced crystallization was followed by a chain cleavage induced crystallization process. The mass loss rate was accelerated after 6 days of degradation. The increase in glass transition temperature during this period further confirmed that the degradation of PLA10GA90 nanofibers was initiated from the amorphous region within the lamellar superstructures. A mechanism of structure and morphology changes during in vitro degradation of electrospun PLA10GA90 nanofibers is proposed.     

Use of Cibacron Blue--Sepharose 6B to detect modifications of the non-allosteric 6-phosphofructokinase from Escherichia coli K-12

In crude cell-free extracts of aerobically grown E. coli K-12, the non-allosteric form of 6-phosphofructokinase has a tetrameric molecular weight 140 000 with a low affinity (less than 5%) for the blue dextran chromophore--Cibacron Blue. The allosteric form has the same tetrameric molecular weight, but possesses a strong affinity for the blue dextran chromophore. Under conditions of prolonged storage, purification procedures of mild heat treatment (50 degrees C), the non-allosteric form converts to an active dimer (mol. wt 67 000), which binds to Cibacron Blue (less than 90%). Acid precipitation plus heat treatment prevents the conversion to the dimeric form and retains low Cibacron Blue affinity. These results are consistent with the isolation of a low molecular weight form and suggest that the inherent lability of this enzyme might be due to both non-specific proteolytic modification and a weak quaternary structure.     

Effect of incubation temperature on zearalenone production by strains of Fusarium crookwellense.

After 6 weeks incubation on rice 2 strains of Fusarium crookwellense produced more zearalenone (6060-5010 mg/kg dry wt of culture) at ambient temperature (16-29 degrees C) in daylight than at ambient temperature (18-23 degrees C) in darkness or at controlled temperatures of 11 degrees C, 20 degrees C or 25 degrees C in darkness. Yields at 25 degrees C were low. Incubation at 11 degrees C during the second 3 weeks incubation increased yields only when preliminary incubation had been at 25 degrees C. After 6 weeks incubation at controlled temperatures in darkness, 4 strains produced most zearalenone at 20 degrees C (2460-21 360 mg/kg), 1 strain at 11 degrees C (6570 mg/kg). Yields at a temperature oscillating daily from 10-20 degrees C were less than at 15 degrees C. One of the 5 strains produced appreciable amounts of a-zearlaenol (1645 mg/kg at 20 degrees C) and 2 of nivalenol (340 and 499 mg/kg at 20 degrees C).     

Plasticization of poly(L-lactide) with poly(propylene glycol)

A new plasticizer for poly(L-lactide) (PLA)-poly(propylene glycol) (PPG) is proposed. The advantage of using PPG is that it does not crystallize, has low glass transition temperature, and is miscible with PLA. PLA was plasticized with PPGs with nominal Mw of 425 and 1000 g/mol. Poly(ethylene glycol) (PEG), long known as a plasticizer for PLA, with nominal Mw of 600 g/mol, was also used to plasticize PLA for comparison. The thermal and tensile properties of PLA and PLA with 5-12.5 wt % of the plasticizers were studied. In blends of PLA with PPGs the glass transition temperature was lower than that of neat PLA. Both PPGs enhanced the crystallizability of PLA albeit less than PEG. All of the plasticizers increased also the ability of PLA to plastic deformation which was reflected in a decrease of yield stress and in an increase of elongation at break. The effect was enhanced by the higher PPG content and also by lower molecular weight of PPG. A phase separation occurred only in the blend containing 12.5 wt % of PPG with higher molecular weight. The evidences of crazing were found in deformed samples of PLA with low plasticizer content, whereas the samples with higher content of plasticizers crystallized due to deformation.