Effect of citric acid and processing on the performance of thermoplastic starch/montmorillonite nanocomposites

A facile two steps extrusion processing conditions are used to prepare thermoplastic starch (TPS)/glycerol modified-montmorillonite (GMMT) nanocomposites. X-ray diffraction (XRD) and transmission electron microscopy (TEM) demonstrate glycerol can enlarge the d-spacing and destruct the multilayer structure of montmorillonite (MMT) effectively using high speed emulsifying machine (HSEM) in the first modification step. So the enlarged d-spacing and destructed platelets of MMT are favorable to form intercalated or exfoliated TPS/GMMT nanocomposites in the second melt extrusion processing. However, scanning electron microscopy (SEM) and XRD show the possible competition between TPS matrix and plasticizer for the intercalation between MMT layers can deteriorate the plasticization of TPS. In addition, citric acid (CA) can increase the plasticization of TPS and dispersion of MMT in nanocomposites effectively detected by fourier transform infrared (FT-IR) spectroscopy and SEM. At the same time, this facile processing conditions and CA can improve the mechanical properties and water vapor permeability (WVP) of TPS/GMMT nanocomposites obviously.     

Preparation and mechanical properties of chitosan/carbon nanotubes composites

Biopolymer chitosan/multiwalled carbon nanotubes (MWNTs) nanocomposites have been successfully prepared by a simple solution-evaporation method. The morphology and mechanical properties of the chitosan/MWNTs nanocomposites have been characterized with field emission scanning electron microscopy (SEM), bright field transmission electron microscopy (TEM), optical microscopy (OM), wide-angle X-ray diffraction (XRD), and tensile as well as nanoindentation tests. The MWNTs were observed to be homogeneously dispersed throughout the chitosan matrix. When compared with neat chitosan, the mechanical properties, including the tensile modulus and strength, of the nanocomposites are greatly improved by about 93% and 99%, respectively, with incorporation of only 0.8 wt % of MWNTs into the chitosan matrix.     

Biocompatible epoxy modified bio-based polyurethane nanocomposites: Mechanical property, cytotoxicity and biodegradation

Epoxy modified Mesua ferrea L. seed oil (MFLSO) based polyurethane nanocomposites with different weight % of clay loadings (1%, 2.5% and 5%) have been evaluated as biocompatible materials. The nanocomposites were prepared by ex situ solution technique under high mechanical shearing and ultrasonication at room temperature. The partially exfoliated nanocomposites were characterized by Fourier transform infra-red (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. The mechanical properties such as tensile strength and scratch hardness were improved 2 and 5 times, respectively by nanocomposites formation. Even the impact resistance improved a little. The thermostability of the nanocomposites was enhanced by about 40 °C. Biodegradation study confirmed 5–10 fold increase in biodegradation rate for the nanocomposites compared to the pristine polymers. All the nanocomposites showed non-cytotoxicity as evident from RBC hemolysis inhibition observed in anti-hemolytic assay carried over the sterilized films. The study reveals that the epoxy modified MFLSO based polyurethane nanocomposites deserve the potential to be applicable as biomaterials.     

Nanocomposite films based on xylan-rich hemicelluloses and cellulose nanofibers with enhanced mechanical properties

Interest in xylan-rich hemicelluloses (XH) film is growing, and efforts have been made to prepare XH films with improved mechanical properties. This work described an effective approach to produce nanocomposite films with enhanced mechanical properties by incorporation of cellulose nanofibers (CNFs) into XH. Aqueous dispersions of XH (64-75 wt %), sorbitol (16-25 wt %), and CNF (0-20 wt %) were cast at a temperature of 23 °C and 50% relative humidity. The surface morphology of the films was revealed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The thermal properties and crystal structure of the films were evaluated by thermal analysis (TG) and X-ray diffraction (XRD). The surface of XH films with and without CNF was composed primarily of nanonodules, and CNFs were embedded in the XH matrix. Freeze-dried XH powder was amorphous, whereas the films with and without CNF showed a distinct peak at around 2θ = 18°, which suggested that XH molecules aggregated or reordered in the casting solution or during water evaporation. Furthermore, the nanocomposite films had improved thermal stability. XH film with 25 wt % plasticizer (sorbitol, based on dry XH weight) showed poor mechanical properties, whereas incorporation of CNF (5-20 wt %, based on the total dry mixture) into the film resulted in enhanced mechanical properties due to the high aspect ratio and mechanical strength of CNF and strong interactions between CNF and XH matrix. This effective method makes it possible to produce hemicellulose-based biomaterials of high quality.     

Novel biobased nanocomposites from soybean oil and functionalized organoclay

Novel biobased nanocomposites have been prepared by the cationic polymerization of conjugated soybean oil (CSOY) or conjugated LoSatSoy oil (CLS) with styrene (ST) and divinylbenzene (DVB), and a reactive organomodified montmorillonite (VMMT) clay as a reinforcing phase. This filler has been prepared by the cationic exchange of sodium montmorillonite with (4-vinylbenzyl)triethylammonium chloride in aqueous solution. The nanostructures of the nanocomposites have been determined by using wide-angle X-ray diffraction (WAXD) and transmission electron microscopy (TEM), respectively. The results from WAXD and TEM indicate that a heterogeneous structure consisting of intercalation and partial exfoliation or an intercalation structure exists in the nanocomposites, depending on the amount of VMMT in the polymer matrix. The thermal, mechanical, and organic vapor barrier properties of the nanocomposites have been evaluated by dynamic thermal analysis, thermogravimetric analysis, mechanical testing, and toluene absorption. A significant improvement is observed in the thermal stability, the dynamic bending storage modulus, the compressive modulus, the compressive strength, the compressive strain at failure, and the vapor barrier performance for the CSOY-- and CLS-based nanocomposites with 1-2 wt % VMMT loading, where some individual exfoliated silicate platelets occur. For example, the CLS-based nanocomposite with 1-2 wt % VMMT exhibits increases of 100-128%, 86-92%, and 5-7% in compressive modulus, compressive strength, and compressive strain at failure, respectively. CLS with higher unsaturation and reactivity affords nanocomposites with higher thermal stability and higher mechanical properties than CSOY.     

Drug release from Kollicoat SR 30D-coated nonpareil beads: evaluation of coating level,plasticizer type,and curing condition

A newly available polyvinylacetate aqueous dispersion, Kollicoat SR 30D, was evaluated with respect to its ability to modulate the in vitro release of a highly water-soluble model compound (diphenhydramine hydrochloride) from nonpareil-based systems. Kollicoat SR 30D premixed with a selected plasticizer (10% wt/wt propylene glycol, 2.5% triethyl citrate, or 2.5% dibutyl sebacute), talc, and red #30 lake dye was coated onto the drug beads in an Aeromatic Strea I fluid-bed drier with a Wurster insert using bottom spray. With propylene glycol as the plasticizer, increases in polymer coating level retarded drug release from beads in a stepwise fashion along with apparent permeability, indicating a consistent release mechanisms. Stability studies at 40°C/75% RH revealed gradual decreases in dissolution rate, and additional curing studies further confirmed the dependence of release kinetics on curing condition. Furthermore, the type of plasticizer was found to play a key role. Unplasticized formulations exhibited the fastest dissolution, followed by formulations plasticized with triethyl citrate, propylene glycol, and dibutyl sebacate. All 4 formulations (unplasticized and plasticized), nevertheless, revealed a marked difference between uncured and cured dissolution profiles. Kollicoat SR 30D has, thereby, been demonstrated to effectively retard drug release from nonpareilbased systems. However, selected plasticizer type and subsequent curing condition play important roles in controlling drug release from such a system.     

Morphology and antibacterial activity of carbohydrate-stabilized silver nanoparticles

Silver nanoparticles were prepared by a simple hydrothermal route and chemical reduction using carbohydrates (sucrose, soluble and waxy corn starch) as reducing as well as stabilizing agents. The crystallite size of these nanoparticles was evaluated from X-ray diffraction (XRD) and transmission electron microscopy (TEM) and was found to be 25 nm. The effect of carbohydrates on the morphology of the silver nanocomposites was studied using scanning EM (SEM). The nanocomposites exhibited interesting inhibitory as well as bactericidal activity against both Gram positive and Gram negative bacteria. Incorporation of silver also increased the thermal stability of the carbohydrates.     

Ethylcellulose-Based Matrix-Type Microspheres: Influence of Plasticizer RATIO as Pore-Forming Agent

In this study, ethylcellulose (EC)-based microsphere formulations were prepared without and with triethyl citrate (TEC) content of 10% and 30% by water-in-oil emulsion-solvent evaporation technique. Diltiazem hydrochloride (DH) was chosen as a hydrophilic model drug and used at different drug/polymer ratios in the microspheres. The aim of the work was to evaluate the influence of plasticizer ratio on the drug release rate and physicochemical characteristics of EC-based matrix-type microspheres. The resulting microspheres were evaluated for encapsulation efficiency, particle size and size distribution, surface morphology, total pore volume, thermal characteristics, drug release rates, and release mechanism. Results indicated that the physicochemical properties of microspheres were strongly affected by the drug/polymer ratio investigated and the concentration of TEC used in the production technique. The surface morphology and pore volume of microspheres significantly varied based on the plasticizer content in the formulation. DH release rate from EC-based matrix-type microspheres can be controlled by varying the DH to polymer and plasticizer ratios. Glass transition temperature values tended to decrease in conjunction with increasing amounts of TEC. Consequently, the various characteristics of the EC microspheres could be modified based on the plasticized ratio of TEC.     

Cassava bagasse cellulose nanofibrils reinforced thermoplastic cassava starch

Cellulose cassava bagasse nanofibrils (CBN) were directly extracted from a by-product of the cassava starch (CS) industry, viz. the cassava bagasse (CB). The morphological structure of the ensuing nanoparticles was investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), presence of other components such as sugars by high performance liquid chromatography (HPLC), thermogravimetric analysis (TGA), and X-ray diffraction (XRD) experiments. The resulting nanofibrils display a relatively low crystallinity and were found to be around 2–11 nm thick and 360–1700 nm long. These nanofibrils were used as reinforcing nanoparticles in a thermoplastic cassava starch matrix plasticized using either glycerol or a mixture of glycerol/sorbitol (1:1) as plasticizer. Nanocomposite films were prepared by a melting process. The reinforcing effect of the filler evaluated by dynamical mechanical tests (DMA) and tensile tests was found to depend on the nature of the plasticizer employed. Thus, for the glycerol-plasticized matrix-based composites, it was limited especially due to additional plasticization by sugars originating from starch hydrolysis during the acid extraction. This effect was evidenced by the reduction of glass vitreous temperature of starch after the incorporation of nanofibrils in TPSG and by the increase of elongation at break in tensile test. On the other hand, for glycerol/sorbitol plasticized nanocomposites the transcrystallization of amylopectin in nanofibrils surface hindered good performances of CBN as reinforcing agent for thermoplastic cassava starch. The incorporation of cassava bagasse cellulose nanofibrils in the thermoplastic starch matrices has resulted in a decrease of its hydrophilic character especially for glycerol plasticized sample.     

Pyrogenic temperature affects the particle size of biochar-supported nanoscaled zero valent iron (nZVI) and its silver removal capacity

Particle size of nanoscaled zero valent iron (nZVI) in nanocomposites can be affected by support materials. In this work, nZVI was supported by bamboo-derived biochars produced at 450 °C (BBL) and 600 °C (BBH). Total iron (Fe) contents were 14.4 and 11.9% for nZVI immobilized in BBL (nZVI/BBL) and BBH (nZVI/BBH), respectively. The resultant nanocomposites were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), and scanning electron microscopy/energy-dispersive X-ray analyses (SEM/EDS). The nZVI was successfully embedded in biochar pores and surfaces as confirmed by SEM/EDS and XRD. TEM revealed that particle sizes of nZVI in nZVI/BBL and nZVI/BBH were roughly 26 and 40 nm, respectively. The Ag⁺ sorption isotherms (25–300 mg L^?1 Ag⁺) suggested that 1 kg of nZVI in nZVI/BBL and nZVI/BBH removed as much as 745.5 and 534.5 g Ag⁺, respectively. The results suggested that Ag⁺ removal capacity was related to particle size of nZVI, which was also affected by pyrogenic temperature.     

Thermal properties and flammability of polylactide nanocomposites with aluminum trihydrate and organoclay

Biodegradable polylactide (PLA) nanocomposites with aluminum trihydrate (ATH) and modified montmorillonite (MMT) were prepared via direct melt compounding using a twin-screw micro extruder. The exfoliated and intercalated structures of clay in the matrix were observed by TEM and XRD. The thermal oxidative degradation temperature and activation energy of the PLA/ATH/MMT nanocomposite determined by thermogravimetric analysis are higher than that without addition of ATH and organoclay. The incorporation of layered silicates into the PLA/ATH composite results in further stabilization throughout the degradation step. The V-0 rating (UL94 V) of the PLA nanocomposite has been achieved, and the melt dripping was reduced during combustion. Results showed that high loading of the conventional flame retardant ATH yielded brittle PLA composites; however, replacing a portion of the ATH with modified MMT in the PLA matrix improved this result.     

Fabrication and characterization of poly(lactic acid)/acetyl tributyl citrate/carbon black as conductive polymer composites

By using acetyl tributyl citrate (ATBC) as the plasticizer of poly(lactic acid) (PLA) and carbon black (CB) as conductive filler, electrically conductive polymer composites (CPC) with different CB and ATBC contents were prepared. FTIR revealed that the interaction existed between PLA/ATBC matrix and CB filler and ATBC could improve this interaction. The rheology showed that ATBC could obviously decrease the shear viscosity and improve the fluidity of the composites but just the reverse for CB. With the increasing of CB contents, the enforcement effect, storage modulus, and glass-transition temperature increased but the elongation at break decreased. PLA/ATBC/CB composites exhibited the low electrical percolation thresholds of 0.516, 1.20, 2.46, and 2.74 vol % CB at 30, 20, 10, and 0 wt % ATBC. The conductivity of the composite containing 3.98 vol % CB and 30 wt % ATBC reached 1.60 S/cm. Scanning electron microscopy revealed that the addition of ATBC facilitated the dispersion of the CB in the PLA matrix. Water vapor permeability (WVP) showed that, at the same CB contents, the more ATBC contents there were, the less the values of WVP were.     

Supra-molecular ecobionanocomposites based on polylactide and cellulosic nanowhiskers: synthesis and properties

Successful filler dispersion and establishment of good interfacial contact with the surrounding matrix are essential for optimized reinforcement in polymeric nanocomposites. In particular, in renewable-based composites this can be challenging, where hydrophilic attractions between nanofillers facilitate aggregation. Here an innovative approach to prepare cellulosic nanowhisker (CNW) reinforced polylactide (PLA) is presented. The lactide ring-opening polymerization is initiated from CNW surface hydroxyl groups after partial acetylation to control the grafting density. Grafting of PLA chains is verified by Fourier transform infrared spectroscopy. The resulting nanocomposites display exceptional properties; a heat distortion temperature of 120 °C is achieved at 10 wt % CNW loading and can be further enhanced to reach 150 °C at 15 wt % CNW. The formation of a percolating network is verified by comparison of modulus data with an established theoretical model. Additionally, nucleation by CNWs reduces the crystallization half-time to 15 s compared with 90 s for PLA. Melt-pressed films retain transparency indicating good filler dispersion.     

Characterization of direct cellulase immobilization with superparamagnetic nanoparticles

Abstract

Methods of cellulase immobilization on magnetic particles via glutaraldehyde binding were studied. The binding was confirmed by transmission electronic microscopy (TEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR) and vibrating sample magnetometry (VSM). Samples analyzed by TEM and XRD showed that the magnetic particles with or without bound cellulase were all nanosized particles with a mean diameter of 11.5 nm, and the binding process did not cause significant changes in particle size and structure. Analysis by FTIR showed that the binding of cellulase to the magnetic nanoparticles might be via covalent bonding between residual amine groups on Fe₃O₄ nanoparticles and amine groups of the cellulase. The VSM analysis showed that magnetic nanoparticles with or without bound cellulase were all superparamagnetic. The immobilized cellulase had a wider pH and temperature range and improved storage stability compared with the free enzyme. Determination of the Michaelis constants revealed that the immobilized cellulase had a greater affinity for the cellulosic substrate than the free enzyme. The immobilized cellulase showed better performance on hydrolysis of steam-exploded corn stalks than of bleached sulfite bagasse pulp.     

Synthesis of Ag/BSA composite nanospheres from water-in-oil microemulsion using compressed CO2 as antisolvent

In this work, a novel route to synthesize biomolecule/metal composite nanospheres is proposed. This method combines the advantages that the silver nanoparticles and bovine serum albumin (BSA) can be precipitated simultaneously from water-in-oil microemulsion by the easy control of CO2 pressure, which was revealed by our high-pressure UV-VIS spectra. The Ag/BSA nanocomposites were successfully prepared using this method. The transmission electronic microscopy (TEM) if the obtained nanocomposites shows that the small-sized Ag nanaoparticles are immobilized by the BSA nanospheres, and the phase structure was characterized by X-ray diffraction (XRD). The Ag/BSA nanocomposites show absorption properties at a wavelength around 435 nm.     

A novel enzymatic hydrogen peroxide biosensor based on Ag/C nanocables

A novel enzymatic hydrogen peroxide sensor was successfully fabricated based on the nanocomposites containing of Ag/C nanocables and gold nanoparticles (AuNPs). Ag/C nanocables have been synthesized by a hydrothermal method and then AuNPs were assembled on the surface of Ag/C nanocables. The nanocomposites were confirmed by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and energy-dispersive X-ray spectrometry (EDS). The above nanocomposites have satisfactory chemical stability and excellent biocompatibility. Cyclic voltammetry (CV) was used to evaluate the electrochemical performance of the Ag/C/Au nanocomposites at glassy carbon electrode (GCE). The results indicated that the Ag/C/Au nanocomposites exhibited excellent electrocatalytic activity to the reduction of H(2)O(2). It offered a linear range of 6.7×10(-9) to 8.0×10(-6) M, with a detection limit of 2.2×10(-9) M. The apparent Michaelis-Menten constant of the biosensor was 51.7×10(-6) M. These results indicated that Ag/C/Au nanocomposites have potential for constructing of a variety of electrochemical biosensors.     

The removal of mercury (II) from water by Ag supported on nanomesoporous silica

In this study, the synthesis of SBA-15/Ag nanocomposite materials with different amounts of silver (2.5, 5, and 10 %) has been investigated under acidic conditions by using P123 as a template via the direct method. The nanocomposites of SBA-15 were synthesized by the same method and by the addition of silver salt. Finally, the nanocomposite materials were examined for the removal of mercury ions from wastewater as an adsorbent by the reverse titration method. Characterization was carried out through x-ray diffraction analysis (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and N₂ adsorption-desorption (Brunauer–Emmett–Teller). XRD spectra confirmed the presence of silver nanoparticles within the amorphous silica matrix of SBA-15. The Barrett–Joyner–Halenda analysis showed that SBA-15 and SBA-15/Ag have a narrow pore size distribution. SEM images demonstrated that the morphology of the matrix of SBA-15 is in spherical state. Furthermore, wavelength dispersive x-ray spectroscopy identified the presence and distribution of silver nanoparticles inside the pore channels and outside of them. Typical TEM images of SBA-15 and SBA-15/Ag (5 wt.%) indicated a regular hexagonal pore structure with long-range order and long channels. In SBA-15/Ag (5 wt.%) sample, the nanoparticles of silver was found into the pores and outside of them. The removal of mercury ions from wastewater using mesoporous silica nanocomposite containing silver nanoparticles was studied by the reverse titration analysis. The best capacity of adsorption of mercury ions from wastewater was obtained for SBA-15/Ag (5 wt.%) sample, which was equal to 42.26 mg/g in 20 min at pH of 7. The Freundlich model was used to explain the adsorption characteristics for the heterogeneous surface, and \( {K}_{\mathrm{f}} \) (adsorption capacity) and n (adsorption intensity) were determined for Hg (II) ion adsorption on SBA-15/Ag nanocomposite materials with different amounts of silver (2.5, 5, and 10 %). The value of R ² was about 0.99, 0.99, 0.98, and 0.98 and K _f was about 42, 48, 58, and 58 mg/g for SBA-15/Ag, SBA-15/Ag (2.5 %), SBA-15/Ag (5 %), and SBA-15/Ag (10 %), respectively. Furthermore, the values of n >1 show a favorable adsorption process for Hg (II) ion adsorption on SBA-15/Ag nanocomposite materials. Moreover, the Langmuir isotherm model evaluation showed that the correlation coefficients for all concentrations were R ² >0.99, indicating that Hg (II) ions were adsorbed on the surface of SBA-15/Ag via chemical and physical interaction. Additionally, the analytic hierarchy process (AHP) and Technique of Order Preference Similarity to the Ideal Solution (TOPSIS) methods that depend on the criteria of the surface area, amount of adsorbent, pore volume, and cost of synthesis were used. The evaluation of results showed that the best sample was SBA-15/Ag (5 wt.%). Furthermore, the research work highlighted the antibacterial nanocomposite with suitable adsorption of Hg (II) ions from water solutions and supported its potential for environmental applications. This nanocomposite can be used in the absorption domain of Hg (II) ions from water solutions.     

Rapid exfoliation of rectorite in quaternized carboxymethyl chitosan

Exfoliated quaternized carboxymethyl chitosan/rectorite (QCMC/REC) nanocomposite was prepared via microwave irradiation method for 70min, which was performed in only water without any additional plasticizer. XRD, TEM, AFM, SEM and FTIR results revealed that when the mass ratio of QCMC to REC was no less than 4:1, the silicate layers of REC were completely exfoliated in QCMC matrix and were homogenous with QCMC, the surface of QCMC/REC nanobiocomposite was very smooth; two types of interactions of hydrogen bond and electrostatic attraction existed in the QCMC/REC nanobiocomposite. Thermal analysis indicated that QCMC/REC nanobiocomposite had higher thermal stability than only QCMC. Therefore, the microwave irradiation method appears to be a promising tool for preparing exfoliated biopolymer/layered silicate nanocomposites at a mild condition.     

Plasticization of poly(L-lactide) with poly(propylene glycol)

A new plasticizer for poly(L-lactide) (PLA)-poly(propylene glycol) (PPG) is proposed. The advantage of using PPG is that it does not crystallize, has low glass transition temperature, and is miscible with PLA. PLA was plasticized with PPGs with nominal Mw of 425 and 1000 g/mol. Poly(ethylene glycol) (PEG), long known as a plasticizer for PLA, with nominal Mw of 600 g/mol, was also used to plasticize PLA for comparison. The thermal and tensile properties of PLA and PLA with 5-12.5 wt % of the plasticizers were studied. In blends of PLA with PPGs the glass transition temperature was lower than that of neat PLA. Both PPGs enhanced the crystallizability of PLA albeit less than PEG. All of the plasticizers increased also the ability of PLA to plastic deformation which was reflected in a decrease of yield stress and in an increase of elongation at break. The effect was enhanced by the higher PPG content and also by lower molecular weight of PPG. A phase separation occurred only in the blend containing 12.5 wt % of PPG with higher molecular weight. The evidences of crazing were found in deformed samples of PLA with low plasticizer content, whereas the samples with higher content of plasticizers crystallized due to deformation.     

沼泽红假单胞菌生物合成银纳米粒子及其抗菌作用

近年来,利用沼泽红假单胞菌合成银纳米粒子作为一种可靠和环境友好的方法出现。主要利用沼泽红假单胞菌的细胞滤液来还原银离子。制备的纳米粒子用紫外可见光谱(UV-vis)、X射线衍射光谱(XRD)和透射电镜(TEM)进行表征。含有银粒子溶液的UV-vis光谱显示在420 nm-460 nm处出现银纳米粒子的吸收峰。TEM图像表明所形成的银纳米粒子的粒径范围为5 nm-20 nm。纳米粒子的XRD图谱证明产物为金属银。所制备的银纳米粒子对大肠杆菌和金黄色葡萄球菌作抑菌性试验。