Investigation of various factors affecting encapsulation on the In-Cap automatic capsule-filling machine

The purpose of this study was to determine the factors that influence fill weight and weight variability of capsules produced on the In-Cap and to assess any differences in terms of capsule defects between gelatin and HPMC (Quali-V) shells. The In-Cap is an automatic tamping type capsule-filling machine and the low output of ≈3000 capsules/hour makes it ideal for early formulation development and phase I/IIa clinical supplies manufacture. Four commonly used excipients (Avicel PH101, Avicel PH302, A-Tab, and Prosolv HD90) and a poorly flowing drug blend were encapsulated at various pin settings and powder bed heights. The average fill weight and coefficient of weight variation were determined. The percentage of defective capsules formed during encapsulation was calculated. Results of the study showed that pin setting was critical for controlling the fill weight and the weight variation. The order of pin setting with pin 1 (closer to the powder chute) set to a relatively higher position and pin 4 (before ejection) set to a lower position was found to give higher fill weights with relatively lower weight variability. The powder bed height influenced the fill weight for poorly flowing powders. The capsule machine speed did not appear to significantly influence the fill weight. The fill weight and weight variation were found to depend on the flow property of the material. A large percentage of defective capsules was obtained using HPMC shell size #00. Some of the commonly observed defects included split caps and improperly closed filled capsules. In general, appropriate selection of pin settings and bed height can reduce the weight variability seen, especially with poorly flowing high-dose formulations.     

An analysis of association of components of yield and oil in safflower (Carthamus tinctorius L.)

Summary Inter-relationships of various component characters with yield and oil content were analysed using 215 entries of safflower from India and U.S.A. Correlation of capsule number per plant and capsule weight with yield per plant was pronounced and they showed large direct effects on yield. All other components influenced seed yield mainly through these two components. Seed size had little effect on yield while seed number exerted a positive influence. The proportion of hull expressed as per cent of the whole seed revealed a highly significant and inverse relationship with oil content and was mainly responsible for the observed variability in oil content in the material. Although negative association was indicated between seed size and oil content, it was observed to be due to the indirect effect of hull content and not due to direct effect of seed size. Interestingly, yield per plant and its major components, number of capsules and capsule weight, revealed a negligible relationship with oil content. Both direct as well as indirect effects of hull percent and yield per plant were responsible for the favourable effect of seed number on oil content. The correlation of plant height, days to first flowering and total crop growth period with yield and oil content was either negligible or low, offering scope for developing early maturing and dwarf varieties with high yield and oil content. Spine index showed a non-significant association with yield and oil content. Capsule number, capsule weight and hull per cent were observed to be the most important components in breeding for higher yield and oil content.     

Reusable biosorbents in capsules from zoogloea ramigera cells for cadmium removal

A biosorbent was prepared by immobilizing and culturing Zoogloea ramigera cells in calcium alginate capsules to high density. The biosorbent (the cell and its exopolysaccharide "Zooglan") along with the [calcium] alginate is known to be responsible for cadmium removal. The dry weight of the biosorbent reached 107 g/L after 3 days of cultivation and 220 g/L after 5 days based on the core volume of a 2.0-mm diameter capsule used. The biosorbents were completely contained in the core of the capsule where the cells grew preferentially near the shell of the capsules while the polymer distributed homogeneously in the core. The specific cadmium uptake by the capsule biosorbent was 1.9 mg/g adsorbent at an initial cadmium concentration of 3 mg/L. This is 1.24 times more than the specific cadmium uptake by the 1.8-mm beads prepared under a comparable condition. The capsules crosslinked with 1% triethylene tetramine and 1% glutamic dialdehyde solutions were superior to the uncrosslinked capsules in mechanical strength. The crosslinked capsules maintained their mechanical strength and adsorption/desorption capacity even after 30 cycles of repeated use. Copyright 1999 John Wiley & Sons, Inc.     

A novel approach for the extraction of herbicides and pesticides from water using liquid-core microcapsules

A novel perstraction system using liquid-core microcapsules for pesticide and herbicide removal from aqueous environments is proposed. The microcapsules contain an oil, dibutyl sebacate, surrounded by a hydrogel membrane. The extraction efficiency of the capsules was demonstrated with atrazine, methylparathion, ethylparathion, and 2,4-dichloro-phenoxyacetic acid. The results show that all of the tested compounds could be rapidly extracted, typically 75% extraction within 10 minutes using a capsule: liquid volume ratio of only 3.5% for ethylparathion, and that the rate of extraction increased with increasing hydrophobicity of the compound to be extracted. Higher rates of extraction could be achieved by changing the capsule: liquid volume ratio. The effect of different liquid core solvents, size of capsules, agitation rate, and treatment with complexing agents on the properties of the microcapsules and extraction rate were studied. Capsules of a diameter smaller than 0.800 mm show little external resistance to mass transfer. The main resistance to mass transfer of the pesticides/herbicides was found to reside in the hydrogel membrane composed of cross-linked alginate/polyacrylamide. Removal of divalent cations from the membrane by the addition of citrate, resulted in a 50% increase in the mass transfer coefficient, probably as a result of solubilization and exo-diffusion of alginate.     

Carpology,germination and seedling performance in Digitalis thapsi L. (Scrophulariaceae)

Summary

We analyse the fruiting phase of the life cycleof Digitalis thapsi L. We studied the production and size of seeds and capsules, and the interpopulational variability and inter-relationships of these parameters. The capsule volume, number of seeds per capsule, of seeds per individual, and of capsules per individual were inter-related and fairly affected by the medium, whereas seed weight was found to bea more independent character. A germination study showed that the species has agreat germinative capacity and has positive photoblasty. It is non-dormant especially if incubated under experimental conditions close to the climatic conditions of the site of provenance of the samples. An increase in temperature speeds up the process without increasing germinability. The morphological and biometric characteristics of the first stages of development of the species following germination were analysed. It was found that seed weight is not positively correlated with cotyledon length nor with any of the other parameters con-sidered, and that the length of the fifth leaf is a useful parameter to express inter-populational genetic variability. Seedling production in spring seems to be influenced more by physical than by chemical factors.     

Microencapsulation of mammalian cells in a water-insoluble polyacrylate by coextrustion and interfacial precipitation

A process for the microencapsulation of mammalian cells in a commercially available water-insoluble polyacrylate (EUDRAGIT RL) is described, and the effects of process parameters are outlined The polymer dissolved in diethyl phthalate was pumped along the annulus formed from two concentric needles, while the cell suspension was pumped inside the inner needle Droplets of polymer solution containing cells were blown off the end of the needles by a coaxial air stream. The droplets fell into a corn oil-mineral oil curing bath, in which the solvent was removed from the nascent capsule causing the polymer to precipitate around the cell suspension core. Capsules were washed free of oils and solvent in a fractionated plasma that allowed for quantitative transfer of capsules from the oil phase to an aqueous medium. By appropriate adjustment of the coaxial air flow rate, capsule size could be varied from 250-1000 mum, although the most convenient size was found to be 400-700 mum. Adding Ficoll 400 to the cell suspension to match the density of the suspension to the polymer solution resulted in capsules with a well-centered core but did not affect capsule strength. It appeared that increasing the polymer solution concentration or the polymer to the cell flow rate ratio resulted in an increased capsule strength, although differences in capsule size made unequivocal conclusions difficult. These capsules are of potential use as an artificial pancreas for the treatment of diabetes (with pancreatic islets) or for large-scale tissue culture and the production of bioactive products (e.g., with fibroblasts).     

纤维素硫酸钠-聚二甲基二烯丙基氯化铵微胶囊固定化Candida krusei产甘油条件优化

研究了利用一种新型的纤维素硫酸钠／聚二甲基二烯丙基氯化铵（Nacs／PDMDAAc）中空微胶囊包埋Can—dida krusei ZJU5205制备甘油的过程。通过摇瓶培养过程中对初始包菌量、胶囊和胶珠、初始甘油浓度、胶囊大小、胶囊体积／发酵液体积等关键固定化参数和培养条件的优化,确立了NaCS／PDMDAAC微胶囊固定化Candida krusei的最佳工艺参数为包菌量为0．6g／L,发酵初加入20g／L甘油,胶囊体积／发酵液体积为0．4。     

Efficient production of polyhydroxyalkanoates from plant oils by Alcaligenes eutrophus and its recombinant strain

The ability of Alcaligenes eutrophus to grow and produce polyhydroxyalkanoates (PHA) on plant oils was evaluated. When olive oil, corn oil, or palm oil was fed as a sole carbon source, the wild-type strain of A. eutrophus grew well and accumulated poly(3-hydroxybutyrate) homopolymer up to approximately 80% (w/w) of the cell dry weight during its stationary growth phase. In addition, a recombinant strain of A. eutrophus PHB⁻4 (a PHA-negative mutant), harboring a PHA synthase gene from Aeromonas caviae, was revealed to produce a random copolyester of 3-hydroxybutyrate and 3-hydroxyhexanoate from these plant oils with a high cellular content (approximately 80% w/w). The mole fraction of 3-hydroxyhexanoate units was 4–5 mol% whatever the structure of the triglycerides fed. The polyesters produced by the A. eutrophus strains from olive oil were 200–400 kDa (the number-average molecular mass). The results demonstrate that renewable and inexpensive plant oils are excellent carbon sources for efficient production of PHA using A. eutrophus strains. Received: 3 September 1997 / Received revision: 10 November 1997 / Accepted: 16 November 1997     

Gelation conditions and transport properties of hollow calcium alginate capsules

The diameter, membrane thickness, and compression intensity of hollow Ca-alginate capsules were measured at different gelation conditions, such as the reactant concentration, dropping velocity, and gelation time. The optimum operation conditions for preparing capsules were determined at 100 g/L CaCl(2), 10 g/L sodium alginate (Na-alginate), a dropping velocity of 150 droplets/min, and a gelation time of 10 min. Diffusion of some saccharide and amino acid from bulk solution into capsules was investigated, and the diffusion coefficients were calculated by the developed mathematical model. All the tested substances can diffuse easily into the capsules. The combined diffusion coefficients of the capsule D(m) are 92-99% as large as their diffusion coefficients in pure water, while the diffusion coefficients in the capsule membrane D(1) are 60-95% as large as those. By employing polyethylene glycol (PEG) and bovine serum albumin (fraction V) (BSA(V)), the molecular weight cut-off of the capsule was determined. For linear macromolecules, hollow Ca-alginate capsules have a molecular weight cut-off of 4000. No diffusion of BSA(V) into the capsules was observed.     

Photopyroelectric Detection of Vegetable Oils' Adulteration

Highly accurate photopyroelectric (PPE) investigation, in the thermal-wave-resonator-cavity configuration, was combined with gas chromatography (GC), in order to detect adulteration of flax oil by mixing with sunflower oil. It was found that the value of the thermal diffusivity for the investigated mixtures ranges from 8.07 × 10⁸m²/s (pure sunflower oil) to 10.03 × 10⁸m²/s (pure flax oil) and is directly correlated with the total amount of the polyunsaturated fatty acids from oils composition. The correlation between the PPE signal and the composition of unadulterated and adulterated vegetable oils confirms the data obtained previously on fresh and spoiled vegetable oils and suggests that the thermal diffusivity may be a suitable parameter to detect oils' quality and their early spoilage and adulteration.     

Nylon capsule method and alfalfa hay crude protein digestibility evaluation

In a trial with two dairy cows we have determined crude protein total tract digestibility (TTDP_NC) by a new nylon capsule method. Nylon capsules were made of nylon cloth with 42 μm apertures. The capsule shape was lenticular, with 10 mm external diameter and 8 mm internal diameter. The capsules were loaded with two stainless steel balls of 149 mg total weight. The average weight of a sample (milled alfalfa hay) in one capsule was 12.9 mg. In each of the two periods 1260 capsules were inserted orally into each of the two cows. Mean capsule passage time (CPT) through the digestive tract was 36.1 h (s.e. 0.49). The total tract dry matter digestibility determined by the nylon capsule method (TTDM_NC) was significantly (P < 0.05) influenced by the time which the capsules spent in the digestive tract. When CPT was 25.4 h, TTDM_NC was 64.8%, while with CPT 50.4 h it was 70.3%. The mean value of TTDP_NC was 93.8%. A similar value, 92.3%, was obtained by calculation based on the values determined by the nylon bag and the mobile bag methods. The results have shown that it is possible to use the nylon capsule method for the determination of total tract digestibility of individual feed components in cattle.     

Diffusion characteristics and controlled release of bacterial fertilizers from modified calcium alginate capsules

An indigenous Cellulosimicrobium cellulans GS6 isolate able to solubilize insoluble phosphate complexes in soil is a potential bacterial fertilizer. Enclosure of the phosphate-solubilizing bacterium (PSB) in biodegradable capsules may protect the PSB cells inoculated into soil and, in the meantime, enable the control of cell release that confers long-term fertilizing effects. In this study, calcium alginate (CA) was used as the core matrix to encapsulate cells of C. cellulans GS6. The cell-liberating properties of the CA-based capsules were modified by blending with a variety of supplemental materials (SM), including chitin, cellulose, olive oil, and gelatin. The experimental results showed that the maximum cell-release percentage (MCR%) of the capsules decreased in the order of CA-cellulose>CA-olive oil>CA-chitin>CA-gelatin>CA. Furthermore, a mass transport model was developed to accurately describe the kinetics of cell release results for each capsule. The diffusion coefficient (D(e)) of each capsule was also determined from the model simulation. We found that the estimated D(e) values are positively correlated to the release rate with rare exceptions. Lastly, as our results underscored the crucial roles that the type of capsules plays in the rate and amount of cell release, controlled release of the bacterial fertilizer (C. cellulans GS6 cells) may be achieved via the design of capsule materials.     

Long-term effects of prey-availability, partnering and temperature on overall egg capsule output of 'New Zealand flatworms', Arthurdendyus triangulates

Arthurdendyus triangulatus is an invasive terrestrial flatworm that preys on earthworms. To assess A. triangulatus egg capsule production, flatworms were maintained in ventilated polypropylene tubs (7.5 L) kept in controlled environment (CE) chambers or outdoors in the ground. Controlled environment chambers were maintained at 8°C or 14°C, flatworms kept singly or paired within tubs and offered Eisenia fetida according to a weight equalling one‐eighth or one‐half of the mean flatworm weight, or left unfed. The tubs were a successful method for keeping flatworms, with some surviving for over one year. The greatest number of egg capsules produced by an individual A. triangulatus was nine over a 16 week period for a flatworm kept at 14°C and fed at the one‐half regime (0.56 egg capsules flatworm^‐1 week^‐1). Although the effects of treatments varied with CE chambers, there was some evidence from flatworms kept outdoors, that feeding affected egg capsule output, with those flatworms fed at the one‐half regime tending to produce more egg capsules (P= 0.057). Flatworms at the one‐eighth regime or that were unfed produced progressively lighter egg capsules and substantially declined in weight themselves. Nevertheless, even unfed flatworms continued to produce egg capsules for 18 weeks. The lightest egg capsule weighed 8 mg, whilst the heaviest was 180 mg. In the CE chambers at 14°C, there was evidence for two different reproductive/survival strategies. Some flatworms produced cumulatively more egg capsules the longer they survived, whereas others lived longer but produced fewer egg capsules. Flatworms kept without a partner still produced egg capsules up to 35 weeks later. Egg capsules contained a mean of 4.14 (CE chambers) or 4.62 (outdoors) juveniles, with a maximum of 11. Overall, juveniles were 45% of the weight of egg capsules, although larger egg capsules had more juveniles, which comprised a greater proportion of the egg capsule. The conversion of earthworm prey to egg capsule production was estimated at 13%.     

Diversity in capsule and seed morphological and phytochemical features and essential oil composition of korarima (Aframomum corrorima (braun) P. C. M. jansen) collections from Ethiopia

Korarima (Aframomum corrorima (Braun) P. C. M. Jansen) is one of the Ethiopian native perennial aromatic herbs belonging to the family Zingiberaceae. Conservation of genotypes and genetic improvement of korarima has been hampered due to lack of evidences on genetic diversity of korarima. Genetic diversity of 44 korarima collections was assessed based on joint capsules and seeds morphological and phytochemical characters. Chemical composition of essential oil in seed samples has also been investigated. Physical measurements were done manually while total organic nutrients, crude fiber and total ash in the seeds were done in terms of proximate analysis. Essential oil in the seed samples was extracted by hydro-distillation and its chemical composition was analyzed with gas chromatography and mass spectrometry (GC-MS). ANOVA revealed significant variations in all the variables considered except capsule and seed shape. Ayda collections showed the largest record for fresh capsule weight (25.3 g), dry capsule weight (6.6 g), hundred seed weight (2.8 g), seed to husk ratio (2.1), total organic matter (66.6%) and seed essential oil (7.3%). Collection from Bazet was also excellent in dry weight of seed per capsule (4.45 g) while those from Metser were best in fruit husk essential oil (1.45%). Cluster analysis of the 44 collections revealed four groups each showing large (23.82–280.13) and significant (p < 0.01) pairwise genetic distance. The pattern of grouping is weak and does not match with the region of collections indicating the presence of different genetic background within the collections as well as genetic similarity among the collections. Principal component analysis (PCA) revealed about 81.2% of the total variations in the first four PCs and the pattern of grouping is similar to cluster analysis. In Essential oil composition, Bona Kike collection was remarkable in 1, 8-Cineole (60.81%). Ayda collection showed the highest m-Mentha-1,8-diene, (+)- (10.05%) and β-farnesene (24.03%). Adele Bise collection was highest in D-Limonene (20.21%). The genetic variability in essential oil composition among the samples was revealed because of spatial separation. The result suggests the potential of Ethiopian korarima in general and the collections in particular for further improvement and commercialization. Overall, the higher extent of morphological and biochemical genetic diversity observed signpost the high opportunity for genetic improvement of the crop via hybridization and selection.     

星油藤蒴果及种子的性状变异研究

为进行星油藤(Plukenetia volubilis L.)良种选育,对其蒴果和种子的性状变异进行了研究。结果表明,星油藤蒴果中4、5、6裂片果分别为49.71%、37.69%和12.60%,以4和5裂片为主;种子性状变异系数比果实的小,种子性状比果实更稳定。按果裂片类型统计,以4裂片的性状变异系数最小,性状也较为稳定,性状分化变异率有54.19%~95.63%来自蒴果间,而果实和种子性状分化变异率分别有79.81%~95.76%和67.66%~93.0%来源于裂片类型,性状分化变异受裂片数影响大,而相同裂片数不同蒴果间的变异程度低。不同裂片类型的果实与种子大多数性状间均存在显著或极显著差异,果裂数是造成性状差异的主要原因。种子萌发率以6裂片果5裂片果4裂片果,平均萌发率超过91%;种子萌发率与单果重、单果重与果形态指标、种子重与种子形态性状间均存在极显著正相关关系,其中单果重对果厚、种子重对种子宽的影响大于其它性状。综合分析星油藤以4裂片果的生物产量最高,平均果重和种子重均好于其他类型。     

Uneven Distribution and Size of Rabbit Lens Capsule Proteoglycans

To document the ultrastructural distribution of lens capsule proteoglycans, rabbit lens capsules were fixed and stained overnight in 50mM sodium acetate, pH 5.6, containing 2.5% glutaraldehyde, 0.2% Cuprolinic Blue and 0.2M MgCl2. They were rinsed, stained with 1% aqueous sodium tungstate, embedded in Epon, sectioned (60nm), and examined with an electron microscope at 60kV.Proteoglycan–Cuprolinic Blue complexes mainly appeared as networks of small electron-dense filaments throughout the posterior and anterior capsules. The posterior capsule was a single layer with a network of small proteoglycan filaments gradually decreasing in size from the humoral side (90×10nm) to the lenticular side (30×8nm). The humoral side of the anterior capsule had a thin lamina (400nm) containing large (180×40nm), very electron-dense proteoglycan–Cuprolinic Blue complexes plus small proteoglycans. Below this lamina, the complexes were only seen as filaments slightly smaller than those in the corresponding area of the posterior capsule.Cuprolinic Blue binding of the anterior and posterior lens capsules revealed differences in the size and distribution of their sulphated proteoglycans which do not correspond to the patterns of their immunoreactivity with anti-heparan sulphate proteoglycan. The humoral lamina in the anterior capsules, with large proteoglycan structures, might be a distinct structural and functional compartment.     

The latex capacity of opium poppy capsules is fixed early in capsule development and is not a major determinant in morphine yield

This study found that the latex capacity (mg latex mg⁻¹ dry weight capsule) of opium poppy capsules is fixed early in capsule development. Latex capacity, which represents the proportion of the capsule wall allocated to laticifers (specialised cells for latex storage), had peaked in the capsule at 1 week after flowering. In contrast, the morphine content of capsules continued to increase with capsule development until commercial harvest. Morphine content was correlated with capsule mass and total latex mass, but there was no correlation between latex capacity and morphine yield. The most important morphological characteristic in terms of morphine end yield (commercial harvest stage) was capsule mass. The findings of this study demonstrate that although latex yield per plant is a highly heritable morphological characteristic, it may have limited potential for use in a breeding strategy aimed at increasing the morphine yield from capsules.     

Rapid determination of zearalenone in edible oils by HPLC with fluorescence detection

A fast, cost-efficient, sensitive and accurate assay method for zearalenone in edible oils is described, as an alternative to gel permeation chromatography (GPC). Oil samples were extracted with an alkaline mixture of methanol and water (methanol +10 g/l aqueous ammonium carbaminate solution, pH 9; 9 + 1, v+v). The pH of the extract was neutralized with hydrochloric acid and then concentrated to dryness. The residue was dissolved with HPLC solvent, and zearalenone was determined by high-performance liquid chromatography with fluorometric detection (HPLC-FLD). The method was successfully validated for two matrices, maize oil and rapeseed oil. The recovery rate was 87%, and the coefficient of variation was 2.8% in a rapeseed oil sample contaminated with 27 μg zearalenone/kg. At a signal-to-noise ratio of 3:1, the method detection limit was 10 μg/kg, which was considered to be adequate in view of the present European Union maximum level of 400 μg/kg.     

Mathematical multi-scale model of the cardiovascular system including mitral valve dynamics. Application to ischemic mitral insufficiency

The aim of this research is to propose a small intestine model for electrically propelled capsule endoscopy. The electrical stimulus can cause contraction of the small intestine and propel the capsule along the lumen. The proposed model considered the drag and friction from the small intestine using a thin walled model and Stokes' drag equation. Further, contraction force from the small intestine was modeled by using regression analysis. From the proposed model, the acceleration and velocity of various exterior shapes of capsule were calculated, and two exterior shapes of capsules were proposed based on the internal volume of the capsules. The proposed capsules were fabricated and animal experiments were conducted. One of the proposed capsules showed an average (SD) velocity in forward direction of 2.91 ± 0.99 mm/s and 2.23 ± 0.78 mm/s in the backward direction, which was 5.2 times faster than that obtained in previous research. The proposed model can predict locomotion of the capsule based on various exterior shapes of the capsule.     

Characterisation of small molecules diffusion in hydrogel-membrane liquid-core capsules

The overall diffusion coefficients for several low molecular weight solutes, such as glucose, fructose, sucrose, lactose, and vitamin B(12) have been determined in Ca-alginate membrane liquid-core capsules using the unsteady-state method following the release of solutes from the capsules to a well-stirred solution of limited volume. The diffusion coefficients obtained for saccharides were 5-20% lower than the corresponding diffusivity in water while for vitamin B(12) about 50% that of water. The diffusion coefficients of the investigated capsules were not influenced by the change in alginate concentration in the capsule membrane from 0.5 to 1.0%. Lower diffusivities and higher deviations from the diffusivity in water were obtained for higher molecular weight solutes.