THE PREPARATION OF THE GRADED COLLODION MEMBRANES OF ELFORD AND THEIR USE IN THE STUDY OF FILTERABLE VIRUSES

1. The method described by Elford for the preparation of graded collodion membranes suitable for ultrafiltration was found to give excellent results, and his findings are fully confirmed. 2. A formula is given for the preparation of collodion from which satisfactory membranes of graded porosity can be prepared. 3. The technique and apparatus used in the preparation, and standardization of membranes are described in detail. 4. The technique and apparatus required for ultrafiltration experiments are described, and some drawbacks encountered in the experiments are discussed. 5. The results of ultrafiltration experiments show that the pores of the membranes are remarkably uniform in size.     

Ion transport through dimethyl sulfoxide (DMSO) induced transient water pores in cell membranes

It is well known that dimethyl sulphoxide (DMSO) increases membrane permeability, which makes it widely used as a vehicle to facilitate drug delivery across biological membranes. However, the mechanism of how DMSO increases membrane permeability has not been well understood. Recently, molecular dynamics simulations have demonstrated that DMSO can induce water pores in biological membranes, but no direct experimental evidence is so far available to prove the simulation result. Using FluxOR Tl? influx assay and intracellular Ca2? imaging technique, we studied the effect of DMSO on Tl? and Ca2? permeation across cell membranes. Upon application of DMSO on CHO-K1 cell line, Tl? influx was transiently increased in a dose-dependent manner. The increase in Tl? permeability induced by DMSO was not changed in the presence of blockers for K? channel and Na?-K? ATPase, suggesting that Tl? permeates through transient water pores induced by DMSO to enter into the cell. In addition, Ca2? permeability was significantly increased upon application of DMSO, indicating that the transient water pores induced by DMSO were non-selective pores. Furthermore, similar results could be obtained from RAW264.7 macrophage cell line. Therefore, this study provided experimental evidence to support the prediction that DMSO can induce transient water pores in cell membranes, which in turn facilitates the transport of active substances across membranes.     

A lipocentric view of peptide-induced pores

Although lipid membranes serve as effective sealing barriers for the passage of most polar solutes, nonmediated leakage is not completely improbable. A high activation energy normally keeps unassisted bilayer permeation at a very low frequency, but lipids are able to self-organize as pores even in peptide-free and protein-free membranes. The probability of leakage phenomena increases under conditions such as phase coexistence, external stress or perturbation associated to binding of nonlipidic molecules. Here, we argue that pore formation can be viewed as an intrinsic property of lipid bilayers, with strong similarities in the structure and mechanism between pores formed with participation of peptides, lipidic pores induced by different types of stress, and spontaneous transient bilayer defects driven by thermal fluctuations. Within such a lipocentric framework, amphipathic peptides are best described as pore-inducing rather than pore-forming elements. Active peptides bound to membranes can be understood as a source of internal surface tension which facilitates pore formation by diminishing the high activation energy barrier. This first or immediate action of the peptide has some resemblance to catalysis. However, the presence of membrane-active peptides has the additional effect of displacing the equilibrium towards the pore-open state, which is then maintained over long times, and reducing the size of initial individual pores. Thus, pore-inducing peptides, regardless of their sequence and oligomeric organization, can be assigned a double role of increasing the probability of pore formation in membranes to high levels as well as stabilizing these pores after they appear.     

Protein Arcs May Form Stable Pores in Lipid Membranes

Electron microscopy and atomic force microscopy images of cholesterol-dependent cytolysins and related proteins that form large pores in lipid membranes have revealed the presence of incomplete rings, or arcs. Some evidence indicates that these arcs are inserted into the membrane and induce membrane leakage, but other experiments seem to refute that. Could such pores, only partially lined by protein, be kinetically and thermodynamically stable? How would the lipids be structured in such a pore? Using the antimicrobial peptide protegrin-1 as a model, we test the stability of pores only partially lined by peptide using all-atom molecular dynamics simulations in POPC and POPE/POPG membranes. The data show that, whereas pure lipid pores close rapidly, pores partially lined by protegrin arcs are stable for at least 300 ns. Estimates of the thermodynamic stability of these arcs using line tension data and implicit solvent calculations show that these arcs can be marginally stable in both zwitterionic and anionic membranes. Arcs provide an explanation for the observed ion selectivity in protegrin electrophysiology experiments and could possibly be involved in other membrane permeabilization processes where lipids are thought to participate, such as those induced by antimicrobial peptides and colicins, as well as the Bax apoptotic pore.     

Protein Arcs May Form Stable Pores in Lipid Membranes

Electron microscopy and atomic force microscopy images of cholesterol-dependent cytolysins and related proteins that form large pores in lipid membranes have revealed the presence of incomplete rings, or arcs. Some evidence indicates that these arcs are inserted into the membrane and induce membrane leakage, but other experiments seem to refute that. Could such pores, only partially lined by protein, be kinetically and thermodynamically stable? How would the lipids be structured in such a pore? Using the antimicrobial peptide protegrin-1 as a model, we test the stability of pores only partially lined by peptide using all-atom molecular dynamics simulations in POPC and POPE/POPG membranes. The data show that, whereas pure lipid pores close rapidly, pores partially lined by protegrin arcs are stable for at least 300 ns. Estimates of the thermodynamic stability of these arcs using line tension data and implicit solvent calculations show that these arcs can be marginally stable in both zwitterionic and anionic membranes. Arcs provide an explanation for the observed ion selectivity in protegrin electrophysiology experiments and could possibly be involved in other membrane permeabilization processes where lipids are thought to participate, such as those induced by antimicrobial peptides and colicins, as well as the Bax apoptotic pore.     

Biotechnical and other applications of nanoporous membranes

Recent advances mean that arrays of nearly uniform cylindrical, conical and pyramidal shaped pores can be produced in several types of substrates. Surface modification of nanopore surfaces can give unique mass transport characteristics that have recently been explored for biomolecule separation, detection and purification. Recent interest has focused on the use of nanoporous membranes for mass transfer diodes that act analogous to solid-state devices based on electron conduction. Asymmetric pores such as conical pores can show superior performance characteristics compared to traditional cylindrical pores in ion rectification. However, many phenomena for membranes with asymmetric pores still remain to be exploited in biomolecular separation, biosensing, microfluidics, logic gates, and energy harvesting and storage.     

Ion transport through dimethyl sulfoxide (DMSO) induced transient water pores in cell membranes

Abstract

It is well known that dimethyl sulphoxide (DMSO) increases membrane permeability, which makes it widely used as a vehicle to facilitate drug delivery across biological membranes. However, the mechanism of how DMSO increases membrane permeability has not been well understood. Recently, molecular dynamics simulations have demonstrated that DMSO can induce water pores in biological membranes, but no direct experimental evidence is so far available to prove the simulation result. Using FluxOR Tl⁺ influx assay and intracellular Ca²⁺ imaging technique, we studied the effect of DMSO on Tl⁺ and Ca²⁺ permeation across cell membranes. Upon application of DMSO on CHO-K1 cell line, Tl⁺ influx was transiently increased in a dose-dependent manner. The increase in Tl⁺ permeability induced by DMSO was not changed in the presence of blockers for K⁺ channel and Na⁺-K⁺ ATPase, suggesting that Tl⁺ permeates through transient water pores induced by DMSO to enter into the cell. In addition, Ca²⁺ permeability was significantly increased upon application of DMSO, indicating that the transient water pores induced by DMSO were non-selective pores. Furthermore, similar results could be obtained from RAW264.7 macrophage cell line. Therefore, this study provided experimental evidence to support the prediction that DMSO can induce transient water pores in cell membranes, which in turn facilitates the transport of active substances across membranes.     

The exocytotic fusion pore modeled as a lipidic pore.

Freeze-fracture electron micrographs from degranulating cells show that the lumen of the secretory granule is connected to the extracellular compartment via large (20 to 150 nm diameter) aqueous pores. These exocytotic fusion pores appear to be made up of a highly curved bilayer that spans the plasma and granule membranes. Conductance measurements, using the patch-clamp technique, have been used to study the fusion pore from the instant it conducts ions. These measurements reveal the presence of early fusion pores that are much smaller than those observed in electron micrographs. Early fusion pores open abruptly, fluctuate, and then either expand irreversibly or close. The molecular structure of these early fusion pores is unknown. In the simplest extremes, these early fusion pores could be either ion channel like protein pores or lipidic pores. Here, we explored the latter possibility, namely that of the early exocytotic fusion pore modeled as a lipid-lined pore whose free energy was composed of curvature elastic energy and work done by tension. Like early exocytotic fusion pores, we found that these lipidic pores could open abruptly, fluctuate, and expand irreversibly. Closure of these lipidic pores could be caused by slight changes in lipid composition. Conductance distributions for stable lipidic pores matched those of exocytotic fusion pores. These findings demonstrate that lipidic pores can exhibit the properties of exocytotic fusion pores, thus providing an alternate framework with which to understand and interpret exocytotic fusion pore data.     

GM1 asymmetry in the membrane stabilizes pores

Cell membranes are highly asymmetric and their stability against poration is crucial for survival. We investigated the influence of membrane asymmetry on electroporation of giant unilamellar vesicles with membranes doped with GM1, a ganglioside asymmetrically enriched in the outer leaflet of neuronal cell membranes. Compared with symmetric membranes, the lifetimes of micronsized pores are about an order of magnitude longer suggesting that pores are stabilized by GM1. Internal membrane nanotubes caused by the GM1 asymmetry, obstruct and additionally slow down pore closure, effectively reducing pore edge tension and leading to leaky membranes. Our results point to the drastic effects this ganglioside can have on pore resealing in biotechnology applications based on poration as well as on membrane repair processes.     

Pore forming activity of the potent RTX-toxin produced by pediatric pathogen Kingella kingae: Characterization and comparison to other RTX-family members

Pediatric septic arthritis in patients under age of four is frequently caused by the oral Gram-negative bacterium Kingella kingae. This organism may be responsible for a severe form of infective endocarditis in otherwise healthy children and adults. A major virulence factor of K. kingae is RtxA, a toxin that belongs to the RTX (Repeats-in-ToXin) group of secreted pore forming toxins. To understand the RtxA effects on host cell membranes, the toxin activity was studied using planar lipid bilayers. K. kingae strain PYKK081 and its isogenic RtxA-deficient strain, KKNB100, were tested for their ability to form pores in artificial membranes of asolectin/n-decane. RtxA, purified from PYKK081, was able to rapidly form pores with an apparent diameter of 1.9 nm as measured by the partition of nonelectrolytes in the pores. The RtxA channels are cation-selective and showed strong voltage-dependent gating. In contrast to supernatants of PYKK081, those of KKNB100 did not show any pore forming activity. We concluded that RtxA toxin is the only secreted protein from K. kingae forming large channels in host cell membranes where it induces cation flux leading to programmed cell death. Furthermore, our findings suggested that the planar lipid bilayer technique can effectively be used to test possible inhibitors of RTX toxin activity and to investigate the mechanism of the toxin binding to the membrane.     

Molecular dynamics simulations of hydrophilic pores in lipid bilayers

Hydrophilic pores are formed in peptide free lipid bilayers under mechanical stress. It has been proposed that the transport of ionic species across such membranes is largely determined by the existence of such meta-stable hydrophilic pores. To study the properties of these structures and understand the mechanism by which pore expansion leads to membrane rupture, a series of molecular dynamics simulations of a dipalmitoylphosphatidylcholine (DPPC) bilayer have been conducted. The system was simulated in two different states; first, as a bilayer containing a meta-stable pore and second, as an equilibrated bilayer without a pore. Surface tension in both cases was applied to study the formation and stability of hydrophilic pores inside the bilayers. It is observed that below a critical threshold tension of approximately 38 mN/m the pores are stabilized. The minimum radius at which a pore can be stabilized is 0.7 nm. Based on the critical threshold tension the line tension of the bilayer was estimated to be approximately 3 x 10(-11) N, in good agreement with experimental measurements. The flux of water molecules through these stabilized pores was analyzed, and the structure and size of the pores characterized. When the lateral pressure exceeds the threshold tension, the pores become unstable and start to expand causing the rupture of the membrane. In the simulations the mechanical threshold tension necessary to cause rupture of the membrane on a nanosecond timescale is much higher in the case of the equilibrated bilayers, as compared with membranes containing preexisting pores.     

Ionic selectivity of melittin-modified flat lipid bilayers]

It has been established in experiments with the bilayer lipid membranes (BLM) that at pH greater than 6.6 the melittin pores are cation-selective and at lower pH they are more selective by anions. The property of melittin pores is shown to be provided by the amino group of the N-terminal glycine residue. The selectivity of melittin-containing membranes may be controlled by the transmembrane potential, the cross-section of water pores being changed. The data obtained are explained within the alimethicine-like model.     

Modeling of discrete currents of single ion channels of cell membranes using synthetic nanometer pores in polyethylene terephthalate films

Study of the conductivity of single supernarrow pores (1–15 nm in diameter) formed in thin membranes (10–12 μm in thickness) from polyethylene terephthalate (PETP) has revealed discrete changes in the currents passing through such pores when applied from an external source of potential difference of 200–1000 mV. Based on several characteristics, such discrete currents (discrete conductivity changes) appeared to be identical to the so-called currents of single ionic channels in cell membranes. The supernarrow pores whose properties are described in the present work were obtained by alkaline etching of tracks in thin PETP membranes (a variant of the so-called nuclear filters). On the walls of the pores, carboxyl groups, i.e., negative fixed charges, and their compensating counterion (cation) layer are formed. Upon setting the potential difference onto the PETP membrane, this cation layer is able to transfer current, through a process called surface conductance. In the case of nanometer-sized diameters of the pores, such surface conductance can turn out to be dominating. We have shown that these discrete changes of currents passing through the nanometer pores are associated with metastability of their surface conductance. In the highly cation-selective channels in the cell membranes, there should inevitably exist an area with dominating cation surface conductance and, hence, conductance metastability. Therefore, a new explanation is proposed of the characteristic discreteness of the currents of single cation-specific ionic channels in cell membranes. Such an explanation does not rule out the existence of any other traditional explanation of the discreteness of ion channel currents.     

Cryofracture electron microscopy of the ookinete pellicle of Plasmodium gallinaceum reveals the existence of novel pores in the alveolar membranes

The malaria parasite invades the midgut tissue of its mosquito host as a motile form called the ookinete. We have examined the pellicle of the ookinete of Plasmodium gallinaceum by freeze-fracture and quick-freeze, deep-etch electron microscopy. The general organization is analogous to that of invasive stages of other members of Apicomplexa. The pellicle is composed of three membranes: the plasma membrane, and the two linked intermediate and inner membranes, which in the ookinete form one flattened vacuole that is located beneath the plasma membrane. The edges of this vacuole form a longitudinal suture. Beneath the vacuole is found an array of microtubules that are connected to the inner membrane by intramembranous particles. During freeze-fracture, the membranes can split along their hydrophobic planes, thus yielding six fracture faces, each of which displays a characteristic pattern of intramembranous particles. Additionally, we find that the ookinete pellicle differs from all other apicomplexan motile stages by the presence of large pores. These pores are of unknown function, but clearly might constitute a novel pathway for the transport of molecules to and from the cortex, which is independent of the well-described route through the apical micronemal/rhoptry complex. The pores may be the route by which motor proteins or other non micronemal surface proteins are trafficked, such as P25/P28 and SOAP, some of which are implicated in transmission blocking immunity.     

Effect of Membrane Structure on the Action of Polyenes: I. Nystatin Action in Cholesterol- and Ergosterol-Containing Membranes

A detailed and thorough characterization of nystatin-induced permeability on lipid bilayers of 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC)-containing ergosterol or cholesterol is presented. The results show that the same collection of transmembrane pores appears in membranes containing either sterol. The concentration range for the appearance of these pores is sterol-dependent. Another mechanism of action, membrane disruption, is also observed in ergosterol-POPC membranes. The greater potency of nystatin present in ergosterol-containing membranes cannot be explained simply by the longer opening times of its pores, as has been suggested; it is also due to an increased number of events in these membranes. The present results and those of a companion paper lead us to propose that membrane structure is the determining factor for drug selectivity in membranes with different sterols.     

Membrane mechanics can account for fusion pore dilation in stages.

Once formed, fusion pores rapidly enlarge to semi-stable conductance values. The membranes lining the fusion pore are continuous bilayer structures, so variations of conductance in time reflect bending and stretching of membranes. We therefore modeled the evolution of fusion pores using the theory of the mechanics of deforming homogeneous membranes. We calculated the changes in length and width of theoretical fusion pores according to standard dynamical equations of motion. Theoretical fusion pores quickly achieve semi-stable dimensions, which correspond to energy minima located in a canyon between energy barriers. The height of the barrier preventing pore expansion diminishes along the dimensions of length and width. The bottom of the canyon slopes gently downward along increasing length. As a consequence, theoretical fusion pores slowly lengthen and widen as the dimensions migrate along the bottom of the canyon, until the barrier vanishes and the pore rapidly enlarges. The dynamics of growth is sensitive to tension, spontaneous curvature, bending elasticity, and mobilities. This sensitivity can account for the quantitative differences in pore evolution observed in two experimental systems: HA-expressing cells fusing to planar bilayer membranes and beige mouse mast cell degranulation. We conclude that the mechanics of membranes could cause the phenomenon of stagewise growth of fusion pores.     

Modeling of discrete currents of single ion channels of cell membranes using synthetic nanometer pores in polyethylene terephthalate films

In studying of conductivity of single supernarrow pores (varying 1 to 15 nm in diameter), formed in thin membranes (10-12 microm in the thickness) from polyethylene terephthalate (PETP), there were revealed discrete changes of currents passing through such pores when applied from external source of potential difference from 200 to 1000 mV. By several characteristics, such discrete currents (discrete conductivity changes) appeared to be identical the so-cold current of single ionic channels in the cell membranes. Supernarrow pores which properties are describes in the present work were obtained as a result of alkaline etching of tracks in thin PETP membranes (a variant of the so-called nuclear filters). Alkaline etching leads to formation of negative fixed charges on the walls of the pores compensated by positive counterions. When setting potential difference onto the PETP membrane, the latter cation layer is able to transfer the current and this transfer was called the surface conductance. In the case of nanometer pores, such surface conductance may be dominating. We have shown that these discrete changes of currents passing through nanometer pores are associated with metastability of the surface conductance. In the case of highly cation-selective channels in the cell membranes it is inevitable, that at least a part of these channels should have dominating cation surface conductance and mentioned above conductance metastability as well. Our findings allow us to propose a new explanation of the origin of the characteristic discreteness of the currents of cation-selective ionic channels in the cell membranes.     

A New Proposal for the Action of Vasopressin, Based on Studies of a Complex Synthetic Membrane

The total osmotic flow of water across cell membranes generally exceeds diffusional flow measured with labeled water. The ratio of osmotic to diffusional flow has been widely used as a basis for the calculation of the radius of pores in the membrane, assuming Poiseuille flow of water through the pores. An important assumption underlying this calculation is that both osmotic and diffusional flow are rate-limited by the same barrier in the membrane. Studies employing a complex synthetic membrane show, however, that osmotic flow can be limited by one barrier (thin, dense barrier), and the rate of diffusion of isotopic water by a second (thick, porous) barrier in series with the first. Calculation of a pore radius is meaningless under these conditions, greatly overestimating the size of the pores determining osmotic flow. On the basis of these results, the estimation of pore radius in biological membranes is reassessed. It is proposed that vasopressin acts by greatly increasing the rate of diffusion of water across an outer barrier of the membrane, with little or no accompanying increase in pore size.     

Mechanisms for the modulation of membrane bilayer properties by amphipathic helical peptides

The amphipathic helix, in which hydrophobia and hydrophilic residues are grouped on opposing faces, is a structural mot if found in many peptides and proteins that bind to membranes. One of the physical properties of membranes that can be altered by the binding of amphipathic helices is membrane monolayer curvature strain. Class A amphipathic helices, which are present in exchangeable plasma lipoproteins, can stabilize membranes by reducing negative monolayer curvature strain; proline-punctuated class A amphipathic helical segments are particularly effective in this regard. This property is suggested to be associated with some of the beneficial biological effects of this protein. On the other hand, lytic amphipathic helical peptides can act by increasing negative curvature strain or by forming pores composed of helical clusters. Thus, different amphipathic helical peptides can be membrane stabilizing or be lytic to membranes, depending on the structural motif of the helix, which in turn determines the nature of its association with membranes. Features of these peptides that are responsible for their specific properties are discussed. © 1994 John Wiley & Sons, Inc.