Carboxymethylcellulose–gelatin–superoxidase dismutase electrode for amperometric superoxide radical sensing

A novel, highly sensitive superoxide dismutase biosensor for the direct and simultaneous determination of superoxide radicals was developed by immobilization of superoxide dismutase within carboxymethylcellulose-gelatin on a Pt electrode surface. The parameters affecting the performance of the biosensor were investigated. The response of the CMC-G-SOD biosensor was proportional to O (2) (·-) concentration and the detection limit was 1.25 × 10(-3) mM with a correlation coefficient of 0.9994. The developed biosensor exhibited high analytical performance with wider linear range, high sensitivity and low response time. The biosensor retained 89.8% of its sensitivity after use for 80 days. The support system enhanced the immobilization of superoxide dismutase and promoted the electron transfer of superoxide dismutase minimizing its fouling effect. The biosensor was quite effective not only in detecting O (2) (·-) , but also in determining the antioxidant properties of acetylsalicylic acid-based drugs and the anti-radical activity of healthy and cancerous human brain tissues.     

Miniature Ag−AgCl electrode for voltage clamping of theAmbystoma collecting duct

Summary We have developed a miniature silver-silver chloride electrode. The outer diameter of the electrodes averaged 22 m and the input resistance 8.8 k. Since the core of the electrode is a glass fiber, the problem of the extreme malleability of a small diameter silver fiber is circumvented. The properties of the electrode permit us to insert it into short (600 m) fragments of the amphibian collecting duct while they are being perfusedin vitro. The passage of currents in the range of 0 to 6×10^–8 amperes allowed us to voltage clamp the nephron fragment between +20 and –20 mV. The current-voltage plots are linear over this range. Two lines of evidence suggest that the voltage clamp is homogeneous. First, the voltage measured at the perfusion end during a voltage-clamp experiment of the tubule is not significantly different from that measured at the collecting end. Secondly, the specific resistance of collecting ducts estimated from the core conductor analysis is 3.3±0.8×10⁴ cm, a value not significantly different from that computed from the current-voltage plots as determined with the Ag–AgCl electrode, 3.0±0.5×10⁴ cm. This method permits precise control of both the ionic and electrical gradients across fragments of the amphibian collecting duct.     

Extradiol dioxygenase-SiO₂ sol-gel modified electrode for catechol and its derivatives detection

A feasible and sensitive biosensor for catechol and its derivatives using 2,3-dihydroxybiphenyl 1,2-dioxygenase (BphC)-modified glassy carbon electrode was successfully constructed by polyvinyl alcohol-modified SiO? sol-gel method. The as-prepared biosensor was characterized by electrochemical impedance spectroscopy, and the surface topography of the film was imaged by atomic force microscope. Liquid chromatography-tandem mass spectrometry was applied to reveal the catalytic mechanism. BphC embedded in SiO? gel maintained its bioactivity well and exhibited excellent eletrocatalytical response to both catechol and some of its derivatives (such as 3-methylcatechol and 4-methylcatechol). The biosensor showed a linear amperometric response range between 0.002 mM and 0.8 mM catechol. And the sensitivity was 1.268 mA/(mM cm2) with a detection limit of 0.428 μM for catechol (S/N = 3). Furthermore, the BphC biosensor exhibited perfect selectivity for catechol in the mixtures of catechol and phenol. It was suggested that this flexible protocol would open up a new avenue for designing other ring-cleavage enzyme biosensors, which could be widely used for monitoring various kinds of environmental pollutants.     

Enantioselective recognition of mandelic acid based on γ-globulin modified glassy carbon electrode

A new chiral biosensor has been fabricated by immobilizing γ-globulin on gold nanoparticles modified glassy carbon electrodes, which could recognize and detect mandelic acid (MA) enantiomers. Differential pulse voltammetry, quartz crystal microbalance, ultraviolet-visible spectroscopy, and atomic force microscopy were used to characterize the enantioselectivity. The results exhibited that γ-globulin modified electrode could enantioselectively recognize MA enantiomers, and larger response signals were obtained from R-MA. The factors influencing the performance of the resulting biosensor were investigated. The enantiomeric composition of R- and S-MA enantiomer mixtures could be determined by measuring the current responses of the sample. The developed electrodes have the advantages of simple preparation, good stability, and rapid detection.     

Phosphorus–iron interaction in sediments: can an electrode minimize phosphorus release from sediments?

All restoration strategies to mitigate eutrophication depend on the success of phosphorus (P) removal from the water body. Therefore, the inputs from the watershed and from the enriched sediments, that were the sink of most P that has been discharged in the water body, should be controlled. In sediments, iron (hydr)oxides minerals are potent repositories of P and the release of P into the water column may occur upon dissolution of the iron (hydr)oxides mediated by iron reducing bacteria. Several species of these bacteria are also known as electroactive microorganisms and have been recently identified in lake sediments. This capacity of bacteria to transfer electrons to electrodes, producing electricity from the oxidation of organic matter, might play a role on P release in sediments. In the present work it is discussed the relationship between phosphorus and iron cycling as well as the application of an electrode to work as external electron acceptor in sediments, in order to prevent metal bound P dissolution under anoxic conditions.     

The influence of the reference electrode location on the M−wave characteristics in the quadriceps

IntroductionIn the compound muscle action potential (M wave) recorded using the belly-tendon configuration, the contribution of the tendon electrode is assumed to be negligible compared to the belly electrode. We tested this assumption by placing the reference electrode at a distant (contralateral) site, which allowed separate recording of the belly and tendon contributions.MethodsM waves were recorded at multiple selected sites over the right quadriceps heads and lower leg using two different locations for the reference electrode: the ipsilateral (right) and contralateral (left) patellar tendon. The general parameters of the M wave (amplitude, area, duration, latency, and frequency) were measured.Results(1) The tendon potential had a small amplitude (<30%) compared to the belly potential; (2) Changing the reference electrode from the ipsilateral to the contralateral patella produced moderate changes in the M wave recorded over the innervation zone, these changes affecting significantly the amplitude of the M−wave second phase (p = 0.006); (3) Using the contralateral reference system allowed recording of short-latency components occurring immediately after the stimulus artefact, which had the same latency and amplitude (p = 0.18 and 0.25, respectively) at all recording sites over the leg.ConclusionsThe potential recorded at the “tendon” site after femoral nerve stimulation is small (compared to the belly potential), but not negligible, and makes a significant contribution to the second phase of belly-tendon M wave. Adopting a distant (contralateral) reference allowed recording of far-field components that may aid in the understanding of the electrical formation of the M wave.     

Electrochemical sensor based on molecularly imprinted membranes at platinum nanoparticles-modified electrode for determination of 17β-estradiol

In this paper, an electrochemical sensor for 17β-estradiol (E2) based on the molecular imprinting polymer (MIP) membranes had been constructed. 6-mercaptonicotinic acid (MNA) and E2 were first assembled on the surface of platinum nanoparticles-modified glassy carbon electrode (PtNPs/GCE) by the formation of Pt-S bonds and hydrogen-bonding interactions, and subsequently the polymer membranes were formed by electropolymerization. Finally, a novel molecularly imprinted sensor (MIS) was obtained after removal of E2. Experimental parameters such as deposition time, scan cycles, pH value and accumulation condition were optimized. Under optimal conditions, the MIS exhibited a large adsorption capacity and high selectivity. A good linearity was obtained in the range of 3.0×10(-8)-5.0×10(-5)molL(-1) (r=0.996) with an estimated detection limit of 1.6×10(-8)molL(-1). MIS had been successfully used to analyze E2 in water samples without complex pretreatment. Meanwhile, the average recoveries were higher than 93.9% with RSD<3.7%. All results above reveal that MIS is an effective electrochemical technique to determine E2 real-time in complicated matrix.     

Immobilization of lysine oxidase on a gold–platinum nanoparticles modified Au electrode for detection of lysine

A commercial lysine oxidase (LyOx) from Trichoderma viride was immobilized covalently onto gold nanoparticles (AuNPs) and platinum nanoparticles (PtNPs) electrodeposited onto Au electrode using 3-aminopropyltriethoxy silane (3-APTES) and glutaraldehyde cross linking chemistry. A lysine biosensor was fabricated using LyOx/3-APTES/AuNPs-PtNPs/Au electrode as a working electrode, Ag/AgCl (3 M KCl) as standard electrode and Pt wire as auxiliary electrode connected through a potentiostat. The enzyme electrode was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The cumulative effect of AuNPs and PtNPs showed excellent electrocatalytic activity at low applied potential for detection of H₂O₂, a product of LyOx reaction. The sensor showed its optimum response within 4 s, when polarized at 0.2 V vs. Ag/AgCl in 0.1 M phosphate buffer, pH 7.5 at 30 °C. The linear range and detection limit of the sensor were 1.0–600 μM and 1.0 μM (S/N = 3), respectively. Biosensor measured lysine level in sera, milk and amino acid tablet, which correlated well with those by standard HPLC method. The enzyme electrode lost 50% of its initial activity after 200 uses over a period of 4 months.     

Application of a Cu–chitosan/multiwalled carbon nanotube film-modified electrode for the sensitive determination of rutin

A new sensitive electrochemical sensor, a glassy carbon electrode modified with chemically cross-linked copper-complexed chitosan/multiwalled carbon nanotubes (Cu–CS/MWCNT/GCE), for rutin analysis was constructed. Experimental investigations of the influence of several parameters showed that the rutin can effectively accumulate on the surface of the Cu–CS/MWCNT/GCE, which accumulation caused a pair of well-defined redox peaks in the electrochemical signal when measurements were carried out in Britton–Robinson buffer solution (pH 3, 0.04 M). The surface of the Cu–CS/MWCNT/GCE was characterized by field-emission scanning electron microscopy, transmission electron microscopy, and X-ray diffractometry analysis. In a rutin concentration range of 0.05–100 μM and under optimized conditions, a linear relationship between the oxidation peak current of rutin and its concentration was obtained with a detection limit of 0.01 μM. The Cu–CS/MWCNT/GCE showed good selectivity, stability, and reproducibility. Moreover, the sensor was used to determine the presence of rutin in fruits with satisfactory results.     

Amperometric immunosensor based on multiwalled carbon nanotubes/Prussian blue/nanogold-modified electrode for determination of α-fetoprotein

In this article, a conspicuously simple and highly sensitive amperometric immunosensor based on the sequential electrodeposition of Prussian blue (PB) and gold nanoparticles (GNPs) on multiwalled carbon nanotube (MWCNT)-modified glassy carbon electrode (GCE) surface is proposed for the detection of α-fetoprotein (AFP). By comparison with PB, the MWCNT/PB composite film had been proven to show much better electrochemical stability and a larger response current. The electrodeposited GNP film can be used not only to immobilize biomolecules but also to avoid the leakage of PB and to prevent shedding of MWCNT/PB composite film from the electrode surface. The performance and factors influencing the performance of the immunosensor were investigated. Under optimal experimental conditions, the proposed immunosensor for AFP was observed with an ultralow limit of detection (LOD) equal to 3 pg/ml (at 3δ), and the linear working range spanned the concentrations of AFP from 0.01 to 300 ng/ml. Moreover, the immunosensor, as well as a commercially available kit, was examined for use in the determination of AFP in real human serum specimens. More significant, the assay mentioned here is simpler than the traditional enzyme-linked immunosorbent assay (ELISA), and an excellent correlation of levels of AFP measured was obtained, indicating that the developed immunoassay could be a promising alternative approach for detection of AFP and other tumor markers in the clinical diagnosis.     

A facilitated electron transfer of copper–zinc superoxide dismutase (SOD) based on a cysteine-bridged SOD electrode

The direct electrochemical redox reaction of bovine erythrocyte copper–zinc superoxide dismutase (Cu₂Zn₂SOD) was clearly observed at a gold electrode modified with a self-assembled monolayer (SAM) of cysteine in phosphate buffer solution containing SOD, although its reaction could not be observed at the bare electrode. In this case, SOD was found to be stably confined on the SAM of cysteine and the redox response could be observed even when the cysteine-SAM electrode used in the SOD solution was transferred to the pure electrolyte solution containing no SOD, suggesting the permanent binding of SOD via the SAM of cysteine on the electrode surface. The electrode reaction of the SOD confined on the cysteine-SAM electrode was found to be quasi-reversible with the formal potential of 65±3 mV vs. Ag/AgCl and its kinetic parameters were estimated: the electron transfer rate constant k_s is 1.2±0.2 s⁻¹ and the anodic (α_a) and cathodic (α_c) transfer coefficients are 0.39±0.02 and 0.61±0.02, respectively. The assignment of the redox peak of SOD at the cysteine-SAM modified electrode could be sufficiently carried out using the native SOD (Cu₂Zn₂SOD), its Cu- or Zn-free derivatives (E₂Zn₂SOD and Cu₂E₂SOD, E designates an empty site) and the SOD reconstituted from E₂Zn₂SOD and Cu²⁺. The Cu complex moiety, the active site for the enzymatic dismutation of the superoxide ion, was characterized to be also the electroactive site of SOD. In addition, we found that the SOD confined on the electrode can be expected to possess its inherent enzymatic activity for dismutation of the superoxide ion.     

The standard electrode potential (Eθ) predicts the prooxidant activity and the acute toxicity of metal ions

The standard electrode potential (E^θ) has been known for many decades to predict the toxicity of metal ions. We have compiled acute toxicity data from fifteen studies and find that the toxicity of thirty metal ions correlates with E^θ at r² = 0.868 when toxicity is expressed as log concentration of comparably effective doses. We have discovered an even stronger relationship between the prooxidant activity (PA) of metal ions and E^θ (and electronegativity, χ). Data compiled from thirty-four studies demonstrate that the PA of twenty-five metal ions correlates with E^θ at r² = 0.983 (and χ at r² = 0.968). PA was commonly measured as metal-induced peroxidation of cell membranes or accumulation of reactive oxygen species. None of the redox metals (capable of Fenton-like reactions) in our studies (i.e., Mn, Fe, Co, Ni, and Cu) was prooxidative or toxic beyond what was expected from E^θ or χ. We propose that the formation of superoxide-metal ion complexes is greater at greater E^θ or χ values and that these complexes, whether free or enzyme-bound, function in PA without redox cycling of the complexed ion.     

Using a dry electrode EEG device during balance tasks in healthy young-adult males: Test–retest reliability analysis

Abstract

Background: The analysis of brain activity during balance is an important topic in different fields of science. Given that all measurements involve an error that is caused by different agents, like the instrument, the researcher, or the natural human variability, a test–retest reliability evaluation of the electroencephalographic assessment is a needed starting point. However, there is a lack of information about the reliability of electroencephalographic measurements, especially in a new wireless device with dry electrodes.

Objective: The current study aims to analyze the reliability of electroencephalographic measurements from a wireless device using dry electrodes during two different balance tests.

Method: Seventeen healthy male volunteers performed two different static balance tasks on a Biodex Balance Platform: (a) with two feet on the platform and (b) with one foot on the platform. Electroencephalographic data was recorded using Enobio (Neuroelectrics). The mean power spectrum of the alpha band of the central and frontal channels was calculated. Relative and absolute indices of reliability were also calculated.

Results: In general terms, the intraclass correlation coefficient (ICC) values of all the assessed channels can be classified as excellent (>0.90). The percentage standard error of measurement oscillated from 0.54% to 1.02% and the percentage smallest real difference ranged from 1.50% to 2.82%.

Conclusion: Electroencephalographic assessment through an Enobio device during balance tasks has an excellent reliability. However, its utility was not demonstrated because responsiveness was not assessed.     

Immobilization of rat brain acetylcholinesterase on porous gold-nanoparticle-CaCO₃ hybrid material modified Au electrode for detection of organophosphorous insecticides

An acetylcholinesterase (AChE) purified from rat brain was immobilized onto gold nanoparticles (AuNPs) assembled on the surface of porous calcium carbonate (CaCO₃) microsphere. The resulting AChE-AuNPs-CaCO₃ bioconjugate was mounted on the surface of Au electrode with the help of silica sol-gel matrix to prepare the working electrode. This electrode was connected to Ag/AgCl (3 M/saturated KCl) as standard and Pt wire as an auxiliary electrode through a potentiostat to construct an organophosphorus (OP) biosensor. The biosensor was based on inhibition of AChE by OP compounds/insecticides. The biosensor showed optimum response at pH 7.0, 30 °C, when polarized at +0.2 V. Two OP compounds, malathion and chlorpyrifos could be detected in the range of 0.1-100 nM and 0.1-70 nM, respectively at 2.0-3.0% inhibition level of AChE. The sensor was reactivated by immersing it in 0.1 mM 2-pyridine aldoxime for 10 min. The detection limit of the sensor was 0.1 nM for both malathion and chlorpyrifos. The biosensor exhibited good reusability (50 times without considerable loss) and storage stability (50% within 60 days, when stored at 4 °C).     

Catalytic effect of cis-diammineplatinum α-pyrrolidone tan adsorbed on a platinum electrode in electrochemical oxidation of water into molecular oxygen

Cyclic voltammograms of cis-diammineplatinum α-pyrrolidone-blue and -tan, [Pt₄(NH₃)₈(C₄H₆NO)₄]ⁿ⁺ (n = 5 and 6, respectively) show for either complex only one redox peak at 0.53 V (average potential of the anodic and cathodic peak potentials). Coulometry and UVVis spectra of bulk- electrolyzed solution indicated that the redox peak corresponds to the reaction [Pt₄(NH₃)₈(C₄H₆NO)₄]⁸⁺ + 4e ⇄ 2[Pt₂(NH₃)₄(C₄H₆NO)₂]²⁺. When cyclic voltammetry is carried out in a solution of [Pt₄(NH₃)₈(C₄H₆NO)₄]⁶⁺ or a platinum electrode adsorbed with [Pt₄(NH₃)₈(C₄H₆NO)₄]⁶⁺ is used in the presence of oxidizing agent in the solution, O₂ gas generates from the electrode surface with large catalytic cathodic current at potentials below ca. 0.8 V. The O₂ gas was confirmed to generate from water by GC-MS analysis. This abnormal O₂ generation phenomenon is explained with cyclic reactions of chemical surface oxide formation on the electrode by the oxidizing agent and electrochemical reduction of the surface oxide. Oxygen gas generates from the reaction of [Pt₄(NH₃)₈(C₄H₆NO)₄]⁸⁺ or [Pt₄(NH₃)₈(C₄H₆NO)₄]⁶⁺ with OH⁻ produced in the course of the electrochemical reduction of the electrode surface oxide. The ability of [Pt₄(NH₃)₈(C₄H₆NO)₄]⁸⁺ and [Pt₄(NH₃)₈(C₄H₆NO)₄]⁶⁺ to oxidize OH⁻ into O₂ has been reported previously.     

Electrochemical oxidation behavior of guanine and adenine on graphene–Nafion composite film modified glassy carbon electrode and the simultaneous determination

The electrochemical behavior of guanine and adenine on the graphene and Nafion composite film modified glassy carbon electrode was investigated by differential pulse voltammetry (DPV). The results indicated that the modified electrode exhibited an excellent electrocatalytic activity towards the oxidation of guanine and adenine, testified by the increased oxidation peak current and decreased oxidation potential. The experimental conditions were optimized. The separation of the two oxidation peaks was 0.364 V in 0.1 M pH 4.4 acetate buffer solution (ABS). Based on this, a novel electrochemical method was proposed to simultaneously determine guanine and adenine with the detection limit of 0.58 (guanine) and 0.75 (adenine) μM (S/N = 3). The proposed method was applied to determine guanine and adenine in milk powder, urine and herring sperm DNA samples with satisfactory results. The value of (G + C)/(A + T) in herring sperm DNA was calculated to be 0.8065. The fabricated electrode showed excellent reproducibility, stability and anti-interference.     

Poly(vinylferrocene)–poly(ethylene glycol) glutamate oxidase electrode for determination of L-glutamate in commercial soy sauces

An amperometric L-glutamate oxidase (GLOD) electrode based on a multilayer of polymer films was developed for the high selective determination of L-glutamate. The multilayer film consisted of three layers as the following configuration i.e., inner membrane of electropolymerized 1,3-diaminobenzene, middle layer of L-GLOD entrapped in photopolymerized poly(vinylferrocene)–poly(ethylene glycol) hydrogel polymer, and outer dialysis membrane. In this manner, the sensor could eliminate interferences and was able to work at a low potential poised at +0.085 V vs. Ag/AgCl. When used in a flow injection system, the sensor responded to L-glutamate in the range 0.5–8.0 mM, with a sensitivity of 9.48 nA mM^–1. The sensor was stable for 5 days of continuous uses (250 assays) and retained 60% activity after 16 days. When used to analyse the L-glutamate contents of a number of different off-the-shelf soy sauces, the sensor gave results in good agreement with the standard colorimetric method.     

Disposable superoxide anion biosensor based on superoxide dismutase entrapped in silica sol–gel matrix at gold nanoparticles modified ITO electrode

A novel disposable biosensor based on direct electron transfer of superoxide dismutase (SOD) was fabricated for the determination of superoxide anion. The biosensor was constructed by electrodeposition of gold nanoparticles (GNPs) on the indium tin oxide (ITO) electrode and then immobilization of SOD in silica sol–gel (SG) network in the presence of cysteine on GNPs/ITO modified electrode surface. The distribution of GNPs on ITO electrode surface was examined by scanning electron microscopy (SEM). The immobilized SOD exhibited high catalytical activity towards superoxide anion. Parameters affecting the performance of the biosensor were also investigated. A linear calibration curve was obtained over the range from 0.08 to 0.64 μM with a correlation coefficient of 0.9937. The resulted biosensors were demonstrated to possess striking analytical properties for superoxide anion determination, such as high sensitivity, good accuracy, and long-term stability. It provides a promising platform for the fabrication of disposable biosensors.     

ZnO–CuxO/polypyrrole nanocomposite modified electrode for simultaneous determination of ascorbic acid,dopamine, and uric acid

Novel zinc oxide (ZnO) nanosheets and copper oxide (Cu_xO, CuO, and Cu₂O) decorated polypyrrole (PPy) nanofibers (ZnO–Cu_xO–PPy) have been successfully fabricated for the simultaneous determination of ascorbic acid (AA), dopamine (DA), and uric acid (UA). The morphology and structure of ZnO–Cu_xO–PPy nanocomposites were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Raman spectroscopy. Compared with the bare glassy carbon electrode (GCE), PPy/GCE, Cu_xO–PPy/GCE, and ZnO–PPy/GCE, ZnO–Cu_xO–PPy/GCE exhibits much higher electrocatalytic activities toward the oxidation of AA, DA, and UA with increasing peak currents and decreasing oxidation overpotentials. Cyclic voltammetry (CV) results show that AA, DA, and UA could be detected selectively and sensitively at ZnO–Cu_xO–PPy/GCE with peak-to-peak separation of 150 and 154 mV for AA–DA and DA–UA, respectively. The calibration curves for AA, DA, and UA were obtained in the ranges of 0.2 to 1.0 mM, 0.1 to 130.0 μM, and 0.5 to 70.0 μM, respectively. The lowest detection limits (signal/noise = 3) were 25.0, 0.04, and 0.2 μM for AA, DA, and UA, respectively. With good selectivity and sensitivity, the current method was applied to the determination of DA in injectable medicine and UA in urine samples.     

Design of a sandwich-mode amperometric biosensor for detection of PML/RARα fusion gene using locked nucleic acids on gold electrode

In this study, a novel DNA electrochemical probe (locked nucleic acid, LNA) was designed and involved in constructing an electrochemical DNA biosensor for detection of promyelocytic leukemia/retinoic acid receptor alpha (PML/RARα) fusion gene in acute promyelocytic leukemia for the first time. This biosensor was based on a 'sandwich' sensing mode, which involved a pair of LNA probes (capture probe immobilized at electrode surface and biotinyl reporter probe as an affinity tag for streptavidin-horseradish peroxidase (streptavidin-HRP). Since biotin can be connected with streptavidin-HRP, this biosensor offered an enzymatically amplified electrochemical current signal for the detection of target DNA. In the simple hybridization system, DNA fragment with its complementary DNA fragment was evidenced by amperometric detection, with a detection limit of 74 fM and a linear response range of 0.1-10 pM for synthetic PML/RARα fusion gene in acute promyelocytic leukemia (APL). Otherwise, the biosensor showed an excellent specificity to distinguish the complementary sequence and different mismatch sequences. The new pattern also exhibited high sensitivity and selectivity in mixed hybridization system.