介孔分子筛MCM-41固定中性脂肪酶条件的研究

以介孔分子筛MCM-41材料为载体,采用物理吸附法对中性脂肪酶进行了固定化处理,并研究不同条件对固定化脂肪酶催化活性的影响,从而得到该种材料对脂肪酶的最佳固定化条件。给酶量为45960 U/g,固定化温度为45℃,pH值为7.5,时间为3 h,此时固定化酶的活力约为4666 U/g。固定化酶和游离酶的最适反应温度都为40℃,最适pH值为7.5,比游离酶低。固定化酶温度稳定性和pH稳定性较游离酶有所提高。     

N-乙酰神经氨酸醛缩酶的固定化及固定化酶性质研究

使用LX-1000HFA氨基树脂对N-乙酰神经氨酸醛缩酶(NAL)进行固定化,并对游离酶与固定化酶的酶学性质及稳定性进行了对比研究。结果显示,最佳固定化条件为载体投放量5.0 g,固定化时间12 h,缓冲液浓度1.0 mol/L,pH7.5,温度25℃。在此条件下制备的固定化NAL活力最高,比酶活可达200 U/g湿载体。与游离酶相比,最适反应温度提高了5℃,最适反应pH没有变化,温度和pH耐受性明显提升。同时固定化酶储存稳定性和操作稳定性也显著增强,在4℃条件下储存10 d后其酶活仅损失6%,重复使用10次后仍保持初始酶活的80%。因此,该固定化酶具有良好的温度稳定性、pH稳定性、储存稳定性和操作稳定性,为酶法工业化生产N-乙酰神经氨酸研究提供了理论依据。     

N-琥珀酰壳聚糖固定化中性蛋白酶的制备及性质研究

以N-琥珀酰壳聚糖为载体固定中性蛋白酶,研究了固定化酶的适宜温度、pH、热稳定性和酸碱稳定性等酶学性质,同时对固定化酶和游离酶的红外光谱图作了分析比较.结果表明:中性蛋白酶经固定化后,最适酶反应pH由7升至8,最适温度没有改变,仍为50℃,所得固定化酶具有较宽的酸碱稳定性范围,在pH 7～9都保持较高活力,并且同定化酶的热稳定性比游离酶有较大的提高.红外光谱分析表明,酶固定化前后的红外光谱图的部分特征峰有较大的差异.     

二氧化硅纳米材料固定中性脂肪酶的条件优化及其特性

以二氧化硅纳米材料为载体,采用吸附法对脂肪酶进行固定化,研究了不同条件对固定化脂肪酶的催化活性的影响,得到最佳的固定化条件:给酶量为28300U/g,固定化温度为45oC,pH值为7.5,时间为10h,此时固定化酶的活力约为3867U/g载体。固定化酶的最适反应温度为45oC,比游离酶的反应温度高5oC,最适pH下降到5.5,低于游离酶的反应pH(pH7)。固定化酶的热稳定性和pH稳定性较游离酶有了很大的提高,其在70oC以下能保持70%以上的酶活力,而游离酶在50oC下残余酶活力仅为30%。在pH5～8的范围内,固定化酶的酶活力能保持50%以上,而游离酶只能保持20%左右。用固定化的中性脂肪酶催化不同的油品,即大豆油、菜籽油及泔水油生产生物柴油,菜籽油的酯化率最高。     

壳聚糖固定化德氏根霉脂肪酶的研究

研究了壳聚糖吸附和戊二醛交联对脂肪酶固定化条件,在室温条件下将0．4g酶粉溶于pH6．0缓冲液中,加入10g壳聚糖,摇匀,再加入浓度为0．6％戊二醛交联6h,得到固定化酶,酶活力回收率约为54．2％。固定化酶的半失活温度比游离酶的高,半失活温度由游离酶的47℃提高到100℃,最适反应温度由40℃上升至80℃,最适pH由6下降到5．5,固定化酶K’m值由游离酶的Km 50mg／mL增加到56mg／mL。该固定化脂肪酶用于酯的合成;在80℃条件下经过10批次连续水解植物油反应,固定化酶的活力仍保持在82．6％以上。     

聚乙烯亚胺/戊二醛交联法固定化重组酯酶大肠杆菌细胞

利用聚乙烯亚胺/戊二醛交联法对重组酯酶大肠杆菌E.coli BL21细胞进行固定化研究,并对交联工艺条件进行优化。结果表明:在大肠杆菌细胞质量浓度200 g/L、硅藻土质量浓度2 g/L、聚乙烯亚胺(PEI)体积分数3%、交联时间1.5 h、戊二醛(GA)体积分数0.5%以及交联时间0.5 h时,固定化细胞的酯酶活力最高。固定化细胞的最适反应温度和pH分别为45℃和8.0,且温度稳定性和pH稳定性均高于游离细胞。当底物浓度为300mmol/L时,固定化细胞重复使用15批次后,其相对酶活仍能保留在80%以上。因此,该固定化细胞具有良好的操作稳定性。     

硅藻土固定中性脂肪酶的制备及其性质

以硅藻土为载体,采用吸附法,对脂肪酶进行固定化,研究了固定化条件对固定化脂肪酶的催化活性的影响,得到最佳的固定化条件：给酶量为33374U/g,固定化温度为35℃,pH值为7.5,时间为4h,此时固定化酶的活力约为5833U/g载体。固定化酶的热稳定性较游离酶有了很大的提高,其在80℃以下能保持80%以上的酶活,而游离酶60℃残余酶活仅为5%。最适反应温度和最适pH值也分别由游离酶的40℃上升至50℃和由7上升到7.5。对固定化中的中性脂肪酶在生物柴油合成中的应用也进行了初步研究。     

米曲霉F-81产中性蛋白酶的固定化条件及其特性

以海藻酸钠为载体,戊二醛为交联剂固定化米曲霉F-81产中性蛋白酶,研究了固定化条件及固定化酶的性质。结果表明,固定化的最佳条件为:固定化时间1 h、海澡酸钠浓度4%、戊二醛浓度9%、CaCl2浓度0.7 mol/L。在此条件下固定化的中性蛋白酶活力为游离酶活力的68%。固定化酶的最适作用温度为65℃,最适作用pH值为7.0。60℃下酶稳定性较好,80℃下处理60 min,粗酶中几乎检测不到酶活力;中性蛋白酶pH稳定范围为6.5-9.5。Km值为24.83 mg/mL,最大反应速率Vmax为0.043 12 mg/min。     

固定化内切型肝素酶的研究

将提纯的一种内切型肝素酶固定于聚酯载体上 ,固定化效率达 78 8%。酶活力在pH为 7 5左右时表现最高 ,并且在此条件下固定化酶的稳定性最好。最适反应温度为 4 0℃。热稳定性试验表明 ,固定化酶的稳定性较差。固定化酶的使用半衰期比游离酶延长 4 4倍。固定化酶催化肝素底物反应的Km 值约为 95 4 μmol L而游离酶的Km 值约为 71 2 μmol L。固定化酶可以同时作用于肝素和硫酸乙酰肝素 ,而对硫酸软骨素没有催化能力。肝素经降解后 ,产生一定量的非硫酸化或低硫酸化的二糖和不同聚合度的寡糖混合物。     

锰过氧化物酶的耦合固定化及其性质研究

分别采用海藻酸钠、明胶和壳聚糖为载体,并以戊二醛为交联剂,通过包埋-交联和吸附-交联两种耦合固定化方法制备固定化锰过氧化物酶。探讨了酶的不同固定化条件和固定化酶的部分性能。与游离酶相比,制备的3种固定化酶最适反应pH分别由7.0降低到5.0、5.0和3.0,最适反应温度分别由35℃升高到75℃、55℃和75℃。3种固定化酶的耐热性都显著提高,其中用壳聚糖制成的固定化酶在pH 2.2～11的宽范围内表现出很好的酸碱耐受性。30℃连续测定6～9次酶活力,重复使用的3种固定化酶显示出良好的稳定性。将固定化酶应用在偶氮染料的脱色中,用明胶制成的固定化酶在静置和摇床条件下,以及用海藻酸钠制成的固定化酶在摇床条件下,均表现出与游离酶相近的脱色能力,并且在重复进行的摇床实验中,脱色能力未降低,反应前后的酶活力均没有损失。     

具有谷氨酸脱羧酶的大肠杆菌固定化细胞

本文研究了用海藻酸钙包埋法制备含谷氨酸脱羧酶固定化细胞的方法以及研究了制备的条件和影响其制备的因素。该法具有包埋细胞活力回收高,方法简便等优点。比较研究了固定化细胞和自然细胞谷氨酸脱羧酶的一些生物化学性质。其中固定化细胞最适pH和pH稳定性增加,最适温度及热稳定性下降;表观米氏常数增大;二价金属离子Zn~(++)、Cu~(++)、Mg~(++)、Fe~(++),Sr~(++)程度不同的抑制酶活性,Ca~(++)激活固定化细胞酶活性,EDTA无抑制作用。对固定化细胞和自然细胞酶活力活化的研究中发现这两种细胞经蒸馏水保温处理后酶活性都上升,且自然细胞酶活的上升较固定化细胞大;而用底物溶液处理后,自然细胞无变化,固定化细胞酶活下降。     

复合诱变选育高产脂肪酶黑曲霉菌株及其固定化酶性质

通过硫酸二乙酯(DES)和微波复合诱变,获得遗传性状稳定的高产脂肪酶黑曲霉突变菌株CM2,酶活达174.93 U/mL.对菌株CM2培养条件的优化,以橄榄油和(NH_4)_2SO_4为最佳碳、氮源,在28℃、pH 7.5的条件下,发酵CM2菌株68 h,脂肪酶活为180.52 U/mL.大孔树脂固定化脂肪酶在35～55℃和pH 7.5～9.5之间有很好的稳定性.游离酶和固定化酶的表观失活活化能分别为52.6842 kJ/mol和30.8391 kJ/mol,固定化酶对温度的敏感度降低,耐受性增强.在微水相中脂肪酶催化2-辛醇和乙酸乙烯酯不对称酯交换反应中,(S)-乙酸辛酯的对映选择性高(游离酶e.e.s 85.7%;固定化酶e.e.s 87.7%),显示了该固定化酶在2-辛醇的手性拆分方面具有良好的应用前景.     

Degradation of carbazole by microbial cells immobilized in magnetic gellan gum gel beads

Polycyclic aromatic heterocycles, such as carbazole, are environmental contaminants suspected of posing human health risks. In this study, we investigated the degradation of carbazole by immobilized Sphingomonas sp. strain XLDN2-5 cells. Four kinds of polymers were evaluated as immobilization supports for Sphingomonas sp. strain XLDN2-5. After comparison with agar, alginate, and kappa-carrageenan, gellan gum was selected as the optimal immobilization support. Furthermore, Fe(3)O(4) nanoparticles were prepared by a coprecipitation method, and the average particle size was about 20 nm with 49.65-electromagnetic-unit (emu) g(-1) saturation magnetization. When the mixture of gellan gel and the Fe(3)O(4) nanoparticles served as an immobilization support, the magnetically immobilized cells were prepared by an ionotropic method. The biodegradation experiments were carried out by employing free cells, nonmagnetically immobilized cells, and magnetically immobilized cells in aqueous phase. The results showed that the magnetically immobilized cells presented higher carbazole biodegradation activity than nonmagnetically immobilized cells and free cells. The highest biodegradation activity was obtained when the concentration of Fe(3)O(4) nanoparticles was 9 mg ml(-1) and the saturation magnetization of magnetically immobilized cells was 11.08 emu g(-1). Additionally, the recycling experiments demonstrated that the degradation activity of magnetically immobilized cells increased gradually during the eight recycles. These results support developing efficient biocatalysts using magnetically immobilized cells and provide a promising technique for improving biocatalysts used in the biodegradation of not only carbazole, but also other hazardous organic compounds.     

诱变选育脂肪酶高产菌株及其脂肪酶固定化

以紫外和微波复合诱变选育脂肪酶产生菌 Rhizopus sp. RXF12,获得高产突变株RZ13,其脂肪酶摇瓶发酵单位是出发株的2.62倍。菌株经多次传代,遗传性状稳定。对RZ13菌株的发酵条件进行了正交优化,在25 ℃、pH 8.0的条件下,接入5 %(v/v)的RZ13菌株单孢子悬液 (107个/ml) 振荡培养84 h,达到RZ13菌株最佳产酶状态,脂肪酶活可达95.08 U/ml。考察了脂肪酶性质,在低于40 ℃,pH 7.0~9.0范围内脂肪酶活稳定。经载体筛选及固定化过程优化,选用镁铝水滑石25℃吸附4 h,对RZ13脂肪酶进行了固定化。结果表明,固定化酶的最适作用温度为35~55℃,pH为7.5~9.0,较游离酶的均有较大扩展。     

Physiological tests for yeast brewery cells immobilized on modified chamotte carrier

In this study yeast cell physiological activity was assessed on the basis of the in situ activity of two important enzymes, succinate dehydrogenase and pyruvate decarboxylase. FUN1 dye bioconversion and cellular ATP content were also taken as important indicators of yeast cell activity. The study was conducted on six brewing yeast strains, which were either free cells or immobilized on a chamotte carrier. The experimental data obtained indicate clearly that, in most cases, the immobilized cells showed lower enzyme activity than free cells from analogous cultures. Pyruvate decarboxylase activity in immobilized cells was higher than in planktonic cell populations only in the case of the Saccharomyces pastorianus 680 strain. However, in a comparative assessment of the fermentation process, conducted with the use of free and immobilized cells, much more favorable dynamics and carbon dioxide productivity were observed in immobilized cells, especially in the case of brewing lager yeast strains. This may explain the higher total cell density per volume unit of the fermented medium and the improved resistance of immobilized cells to environmental changes.     

Degradation of Carbazole by Microbial Cells Immobilized in Magnetic Gellan Gum Gel Beads

Polycyclic aromatic heterocycles, such as carbazole, are environmental contaminants suspected of posing human health risks. In this study, we investigated the degradation of carbazole by immobilized Sphingomonas sp. strain XLDN2-5 cells. Four kinds of polymers were evaluated as immobilization supports for Sphingomonas sp. strain XLDN2-5. After comparison with agar, alginate, and κ-carrageenan, gellan gum was selected as the optimal immobilization support. Furthermore, Fe₃O₄ nanoparticles were prepared by a coprecipitation method, and the average particle size was about 20 nm with 49.65-electromagnetic-unit (emu) g⁻¹ saturation magnetization. When the mixture of gellan gel and the Fe₃O₄ nanoparticles served as an immobilization support, the magnetically immobilized cells were prepared by an ionotropic method. The biodegradation experiments were carried out by employing free cells, nonmagnetically immobilized cells, and magnetically immobilized cells in aqueous phase. The results showed that the magnetically immobilized cells presented higher carbazole biodegradation activity than nonmagnetically immobilized cells and free cells. The highest biodegradation activity was obtained when the concentration of Fe₃O₄ nanoparticles was 9 mg ml⁻¹ and the saturation magnetization of magnetically immobilized cells was 11.08 emu g⁻¹. Additionally, the recycling experiments demonstrated that the degradation activity of magnetically immobilized cells increased gradually during the eight recycles. These results support developing efficient biocatalysts using magnetically immobilized cells and provide a promising technique for improving biocatalysts used in the biodegradation of not only carbazole, but also other hazardous organic compounds.     

亚栖热菌透性化细胞的耦合固定化研究

将海藻酸盐凝胶包埋法与交联法和聚电解质静电自组装覆膜法相耦合,对含有海藻糖合酶活性的亚栖热菌的透性化细胞进行了固定化研究。结果表明,利用重氮树脂和聚苯乙烯磺酸钠对海藻酸凝胶微球交替覆膜,可以显著提高凝胶微球在磷酸盐缓冲液中的稳定性,以碳二亚胺对固定化细胞进行交联处理则可以提高固定化细胞中海藻糖合酶的热稳定性。透性化细胞经包埋－交联－覆膜耦合固定化后,酶活回收率为32％,最适酶反应pH值由6.5左右升至7.0左右,最适反应温度未变,仍为60℃。所得固定化细胞间歇反应时,催化麦芽糖转化为海藻糖的转化率可达60％,重复使用4次（每次50℃、反应24h）,酶活损失小于20％,转化率可保持在50％以上。     

Characterization of the nitrobenzene-degrading strain Pseudomonas sp. a3 and use of its immobilized cells in the treatment of mixed aromatics wastewater

A bacterial strain Pseudomonas sp. a3 capable of degrading nitrobenzene, phenol, aniline, and other aromatics was isolated and characterized. When nitrobenzene was degraded, the release of NH(4) (+) was detected, but not of NO(2) (-). This result implied that nitrobenzene might have a partial reductive metabolic pathway in strain a3. However, aniline appeared as one of the metabolites during the aerobic degradation of nitrobenzene. Moreover, the appearance of 2-aminophenol during aniline degradation by strain a3 indicated that novel initial reactions existed during the degradation of nitrobenzene and aniline by strain a3. Strain a3 was immobilized in the mixed carrier of polyvinyl alcohol and sodium alginate to improve its degrading efficiency. The optimal concentrations of polyvinyl alcohol and sodium alginate in the mixed carrier were 9 and 3 %, respectively. The immobilized cells had stable degradation activity and good mechanical properties in the recycling tests. The immobilized cells also exhibited higher tolerances in acidic (pH 4-5) and highly saline (10 % NaCl) environments than those of free cells. The biodegradation of nitrobenzene mixed with aniline and phenol using immobilized cells of Pseudomonas sp. a3 was also greatly improved compared with those of free cells. The immobilized cells could completely degrade 300 mg L(-1) nitrobenzene within 10 h with 150 mg L(-1) aniline and 150 mg L(-1) phenol. This result revealed that the immobilized cells of Pseudomonas sp. a3 could be a potential candidate for treating nitrobenzene wastewater mixed with other aromatics.