Optimization of fed-batch fermentation for xylitol production by Candida tropicalis

Xylitol, a functional sweetener, was produced from xylose by biological conversion using Candida tropicalis ATCC 13803. Based on a two-substrate fermentation using glucose for cell growth and xylose for xylitol production, fed-batch fermentations were undertaken to increase the final xylitol concentration. The effects of xylose and xylitol on xylitol production rate were studied to determine the optimum concentrations for fed-batch fermentation. Xylose concentration in the medium (100 g l⁻¹) and less than 200 g l⁻¹ total xylose plus xylitol concentration were determined as optimum for maximum xylitol production rate and xylitol yield. Increasing the concentrations of xylose and xylitol decreased the rate and yield of xylitol production and the specific cell growth rate, probably because of an increase in osmotic stress that would interfere with xylose transport, xylitol flux to secretion to cell metabolism. The feeding rate of xylose solution during the fed-batch mode of operation was determined by using the mass balance equations and kinetic parameters involved in the equations in order to increase final xylitol concentration without affecting xylitol and productivity. The optimized fed-batch fermentation resulted in 187 g l⁻¹ xylitol concentration, 0.75 g xylitol g xylose⁻¹ xylitol yield and 3.9 g xylitol l⁻¹ h⁻¹ volumetric productivity. Journal of Industrial Microbiology & Biotechnology (2002) 29, 16–19 doi:10.1038/sj.jim.7000257 Received 15 October 2001/ Accepted in revised form 30 March 2002     

Environmental parameters affecting xylitol production from sugar cane bagasse hemicellulosic hydrolyzate by Candida guilliermondii

The bioconversion of xylose to xylitol by Candida guilliermondii FTI 20037 cultivated in sugar cane bagasse hemicellulosic hydrolyzate was influenced by cell inoculum level, age of inoculum and hydrolyzate concentration. The maximum xylitol productivity (0.75 g L⁻¹ h⁻¹) occurred in tests carried out with hydrolyzate containing 54.5 g L⁻¹ of xylose, using 3.0 g L⁻¹ of a 24-h-old inoculum. Xylitol productivity and cell concentration decreased with hydrolyzate containing 74.2 g L⁻¹ of xylose. Received 02 February 1996/ Accepted in revised form 15 November 1996     

Increase of xylitol yield by feeding xylose and glucose in Candida tropicalis

Candida tropicalis, a strain isolated from the sludge of a factory manufacturing xylose, produced a high xylitol concentration of 131 g/l from 150 g/l xylose at 45 h in a flask. Above 150 g/l xylose, however, volumetric xylitol production rates decreased because of a lag period in cell growth. In fed-batch culture, the volumetric production rate and xylitol yield from xylose varied substantially with the controlled xylose concentration and were maximum at a controlled xylose concentration of 60 g/l. To increase the xylitol yield from xylose, feeding experiments using different ratios of xylose and glucose were carried out in a fermentor. The maximum xylitol yield from 300 g/l xylose was 91% at a glucose/xylose feeding ratio of 15%, while the maximum volumetric production rate of xylitol was 3.98 g l⁻¹ h⁻¹ at a glucose/xylose feeding ratio of 20%. Xylitol production was found to decrease markedly as its concentration rose above 250 g/l. In order to accumulate xylitol to 250 g/l, 270 g/l xylose was added in total, at a glucose/xylose feeding ratio of 15%. Under these conditions, a final xylitol production of 251 g/l, which corresponded to a yield of 93%, was obtained from 270 g/l xylose in 55 h. Received: 20 April 1998 / Received revision: 29 May 1998 / Accepted: 19 June 1998     

Production of xylitol in cell recycle fermentations of Candida tropicalis

Xylitol was produced a in two-substrate, batch fermentation with cell recycling of Candida tropicalis ATCC 13803. A series of cell-recycle experiments showed that the feeding of xylose, glucose and yeast extract in the xylitol production phase was most effective in enhancing xylitol productivity. The optimized cell recycle fermentation resulted in 0.82 g xylitol/g xylose yield, 4.94 g xylitol l^–1 h^–1 productivity, and final xylitol concentration of 189 g l^–1. These results were 1.3 times higher in volumetric xylitol productivity and 2.2 times higher in final product concentration compared with the corresponding values of the optimized two-substrate batch culture.     

Production of xylitol by Candida peltata

Candida peltata NRRL Y-6888 to ferment xylose to xylitol was evaluated under different fermentation conditions such as pH, temperature, aeration, substrate concentration and in the presence of glucose, arabinose, ethanol, methanol and organic acids. Maximum xylitol yield of 0.56 g g⁻¹ xylose was obtained when the yeast was cultivated at pH 6.0, 28°C and 200 rpm on 50 g L⁻¹ xylose. The yeast produced ethanol (0.41 g g⁻¹ in 40 h) from glucose (50 g L⁻¹) and arabitol (0.55 g g⁻¹ in 87 h) from arabinose (50 g L⁻¹). It preferentially utilized glucose > xylose > arabinose from mixed substrates. Glucose (10 g L⁻¹), ethanol (7.5 g L⁻¹) and acetate (5 g L⁻¹) inhibited xylitol production by 61, 84 and 68%, respectively. Arabinose (10 g L⁻¹) had no inhibitory effect on xylitol production. Received 24 December 1998/ Accepted in revised form 18 March 1999     

Continuous bio-catalytic conversion of sugar mixture to acetone–butanol–ethanol by immobilized <Emphasis Type="Italic">Clostridium acetobutylicum</Emphasis> DSM 792

Continuous production of acetone, n-butanol, and ethanol (ABE) was carried out using immobilized cells of Clostridium acetobutylicum DSM 792 using glucose and sugar mixture as a substrate. Among various lignocellulosic materials screened as a support matrix, coconut fibers and wood pulp fibers were found to be promising in batch experiments. With a motive of promoting wood-based bio-refinery concept, wood pulp was used as a cell holding material. Glucose and sugar mixture (glucose, mannose, galactose, arabinose, and xylose) comparable to lignocellulose hydrolysate was used as a substrate for continuous production of ABE. We report the best solvent productivity among wild-type strains using column reactor. The maximum total solvent concentration of 14.32 g L⁻¹ was obtained at a dilution rate of 0.22 h⁻¹ with glucose as a substrate compared to 12.64 g L⁻¹ at 0.5 h⁻¹ dilution rate with sugar mixture. The maximum solvent productivity (13.66 g L⁻¹ h⁻¹) was obtained at a dilution rate of 1.9 h⁻¹ with glucose as a substrate whereas solvent productivity (12.14 g L⁻¹ h⁻¹) was obtained at a dilution rate of 1.5 h⁻¹ with sugar mixture. The immobilized column reactor with wood pulp can become an efficient technology to be integrated with existing pulp mills to convert them into wood-based bio-refineries.     

Ethanol and xylitol production from glucose and xylose at high temperature by <Emphasis Type="Italic">Kluyveromyces</Emphasis> sp. IIPE453

A yeast strain Kluyveromyces sp. IIPE453 (MTCC 5314), isolated from soil samples collected from dumping sites of crushed sugarcane bagasse in Sugar Mill, showed growth and fermentation efficiency at high temperatures ranging from 45°C to 50°C. The yeast strain was able to use a wide range of substrates, such as glucose, xylose, mannose, galactose, arabinose, sucrose, and cellobiose, either for growth or fermentation to ethanol. The strain also showed xylitol production from xylose. In batch fermentation, the strain showed maximum ethanol concentration of 82 ± 0.5 g l⁻¹ (10.4% v/v) on initial glucose concentration of 200 g l⁻¹, and ethanol concentration of 1.75 ± 0.05 g l⁻¹ as well as xylitol concentration of 11.5 ± 0.4 g l⁻¹ on initial xylose concentration of 20 g l⁻¹ at 50°C. The strain was capable of simultaneously using glucose and xylose in a mixture of glucose concentration of 75 g l⁻¹ and xylose concentration of 25 g l⁻¹, achieving maximum ethanol concentration of 38 ± 0.5 g l⁻¹ and xylitol concentration of 14.5 ± 0.2 g l⁻¹ in batch fermentation. High stability of the strain was observed in a continuous fermentation by feeding the mixture of glucose concentration of 75 g l⁻¹ and xylose concentration of 25 g l⁻¹ by recycling the cells, achieving maximum ethanol concentration of 30.8 ± 6.2 g l⁻¹ and xylitol concentration of 7.35 ± 3.3 g l⁻¹ with ethanol productivity of 3.1 ± 0.6 g l⁻¹ h⁻¹ and xylitol productivity of 0.75 ± 0.35 g l⁻¹ h⁻¹, respectively.     

Butanol production from wheat straw hydrolysate using <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis>

In these studies, butanol (acetone butanol ethanol or ABE) was produced from wheat straw hydrolysate (WSH) in batch cultures using Clostridium beijerinckii P260. In control fermentation 48.9 g L⁻¹ glucose (initial sugar 62.0 g L⁻¹) was used to produce 20.1 g L⁻¹ ABE with a productivity and yield of 0.28 g L⁻¹ h⁻¹ and 0.41, respectively. In a similar experiment where WSH (60.2 g L⁻¹ total sugars obtained from hydrolysis of 86 g L⁻¹ wheat straw) was used, the culture produced 25.0 g L⁻¹ ABE with a productivity and yield of 0.60 g L⁻¹ h⁻¹ and 0.42, respectively. These results are superior to the control experiment and productivity was improved by 214%. When WSH was supplemented with 35 g L⁻¹ glucose, a reactor productivity was improved to 0.63 g L⁻¹ h⁻¹ with a yield of 0.42. In this case, ABE concentration in the broth was 28.2 g L⁻¹. When WSH was supplemented with 60 g L⁻¹ glucose, the resultant medium containing 128.3 g L⁻¹ sugars was successfully fermented (due to product removal) to produce 47.6 g L⁻¹ ABE, and the culture utilized all the sugars (glucose, xylose, arabinose, galactose, and mannose). These results demonstrate that C. beijerinckii P260 has excellent capacity to convert biomass derived sugars to solvents and can produce over 28 g L⁻¹ (in one case 41.7 g L⁻¹ from glucose) ABE from WSH. Medium containing 250 g L⁻¹ glucose resulted in no growth and no ABE production. Mixtures containing WSH + 140 g L⁻¹ glucose (total sugar approximately 200 g L⁻¹) showed poor growth and poor ABE production. Mention of trade names or commercial products in this article is solely for the purpose of providing scientific information and does not imply recommendation or endorsement by the United States Department of Agriculture.     

Continuous production of isopropanol and butanol using <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis> DSM 6423

Clostridium beijerinckii DSM 6423 was studied using different continuous production methods to give maximum and stable production of isopropanol and n-butanol. In a single-stage continuous culture, when wood pulp was added as a cell holding material, we could increase the solvent productivity from 0.47 to 5.52 g L⁻¹ h⁻¹ with the yield of 54% from glucose. The overall solvent concentration of 7.51 g L⁻¹ (39.4% isopropanol and 60.6% n-butanol) with the maximum solvent productivity of 0.84 g L⁻¹ h⁻¹ was obtained with two-stage continuous culture. We were able to run the process for more than 48 overall retention times without losing the ability to produce solvents.     

Production of high-density Chlorella culture grown in fermenters

The freshwater microalga Chlorella vulgaris was grown heterotrophically in fed-batch 50–600-L fermenters at 36°C, on aerated and mixed nutrient solution with urea as a nitrogen and glucose as a carbon and energy source. Cell density increased from the initial value 6.25 to 117.18 g DW L⁻¹ in 32 h in the fermenter 50 L at a mean growth rate 3.52 g DW L⁻¹ h⁻¹. The DW increase in the fermenter 200 L was from 7.25 to 94.82 g DW L⁻¹ in 26.5 h at a mean growth rate 3.37 g DW L⁻¹ h⁻¹. Mean specific growth rate μ was about 0.1 h⁻¹ in the both fermenters, if nutrients and oxygen were adequately supplied. The DW increase in the fermenter 600 L was from 0.8 to 81.6 g DW L⁻¹ in 66.5 h at a mean growth rate 1.22 g DW L⁻¹ h⁻¹ and μ = 0.07 h⁻¹. A limitation of the cell growth rate in 600 L fermenter caused by a low dissolved oxygen concentration above cell densities higher than 10 g DW L⁻¹) occurred. Specific growth rate decreased approximately linearly with increasing glucose concentration (25–80 g glucose L⁻¹) at the beginning of cultivation and decreased with the time of cultivation. The cell yield was 0.55–0.69 g DW (g glucose)⁻¹. The content of proteins, β-carotene, and chlorophylls in the cells steadily increased and starch content decreased, by keeping aerated and mixed culture another 12 h in fermenter after the cell growth was stopped due to glucose deficiency.     

Fermentation behavior of osmophilic yeast Candida tropicalis isolated from the nectar of Hibiscus rosa sinensis flowers for xylitol production

Eighteen yeast species belonging to seven genera were isolated from ten samples of nectar from Hibiscus rosa sinensis and investigated for xylitol production using d-xylose as sole carbon source. Amongst these isolates, no. 10 was selected as the best xylitol producer and identified as Candida tropicalis on the basis of morphological, biochemical and 26S rDNA sequencing. C. tropicalis produced 12.11 gl⁻¹ of xylitol in presence of 50 gl⁻¹ of xylose in 72 h at pH 5, 30°C and 200 rpm. The strain of C. tropicalis obtained through xylose enrichment technique has resulted in a yield of 0.5 gg⁻¹ with a xylitol volumetric productivity of 1.07 gl⁻¹h⁻¹ in the presence of 300 gl⁻¹ of xylose through batch fermentation. This organism has been reported for the first time from Hibiscus rosa sinensis flowers. Realizing, the importance of this high valued compound, as a sugar substitute, xylose enrichment technique was developed in order to utilize even higher concentrations of xylose as substrate for maximum xylitol production.     

Continuous propionic acid production from cheese whey usingin situ spin filter

The potential use of spin filter device to retainPropionibacterium acidipropionici in the bioreactor under continuous mode of fermentation and improve propionic acid productivity, was examined. The yield of propionic acid based on lactose concentration was 51% in batch and 54% in continuous (dilution rate=0.05 h⁻¹) operation. The yield in continuous fermentation with cell retention using spin filter of 10 micron size (dilution rate=0.05 h⁻¹) was even higher at 70% (w/w). The volumetric productivity under batch and continuous mode of operation were 0.312 g L⁻¹ h⁻¹ and 0.718 g L⁻¹ h⁻¹ respectively. Continuous fermentation with cell retention demonstrated even higher volumetric productivities at 0.98 g L⁻¹ h⁻¹ with out clogging problems It could be used for utilization of cheese whey to produce propionic acid at higher yield and productivities.     

Xylitol production from a mutant strain of Candida tropicalis

Aims: To characterize the kinetics of growth, sugar uptake and xylitol production in batch and fed‐batch cultures for a xylitol assimilation‐deficient strain of Candida tropicalis isolated via chemical mutagenesis. Methods and Results: Chemical mutagenesis using nitrosoguanidine led to the isolation of the xylitol‐assimilation deficient strain C. tropicalis SS2. Shake‐flask fermentations with this mutant showed a sixfold higher xylitol yield than the parent strain in medium containing 25 g l^?1 glucose and 25 g l^?1 xylose. With 20 g l^?1 glycerol, replacing glucose for cell growth, and various concentrations of xylose, the studies indicated that the mutant strain resulted in xylitol yields from xylose close to theoretical. Under fully aerobic conditions, fed‐batch fermentation with repeated addition of glycerol and xylose resulted in 3·3 g l^?1 h^?1 xylitol volumetric productivity with the final concentration of 220 g l^?1 and overall yield of 0·93 g g^?1 xylitol. Conclusions: The xylitol assimilation‐deficient mutant isolated in this study showed the potential for high xylitol yield and volumetric productivity under aerobic conditions. In the evaluation of glycerol as an alternative low‐cost nonfermentable carbon source, high biomass and xylitol yields under aerobic conditions were achieved; however, the increase in initial xylose concentrations resulted in a reduction in biomass yield based on glycerol consumption. This may be a consequence of the role of an active transport system in the yeast requiring increasing energy for xylose uptake and possible xylitol secretion, with little or no energy available from xylose metabolism. Significance and Impact of the Study: The study confirms the advantage of using a xylitol assimilation‐deficient yeast under aerobic conditions for xylitol production with glycerol as a primary carbon source. It illustrates the potential of using the xylose stream in a biomass‐based bio‐refinery for the production of xylitol with further cost reductions resulting from using glycerol for yeast growth and energy production.     

Characterisation of a novel thermotolerant yeast, Kluyveromyces marxianus var marxianus: development of an ethanol fermentation process

The fermentation characteristics of the novel, thermotolerant, isolate Kluyveromyces marxianus var marxianus were determined to evaluate its aptitude for use in an ethanol production process. Sustainable growth was not observed under anaerobic conditions, even in the presence of unsaturated fatty acid and sterol. A maximum ethanol concentration of 40 g L⁻¹ was produced at 45°C, with an initial specific ethanol production rate of 1.7 g g⁻¹ h⁻¹. This was observed at ethanol concentrations below 8 g L⁻¹ and under oxygen-limited conditions. The low ethanol tolerance and low growth under oxygen-limited conditions required for ethanol production implied that a simple continuous process was not feasible with this yeast strain. Improved productivity was achieved through recycling biomass into the fermenter, indicating that utilising an effective cell retention method such as cell recycle or immobilisation, could lead to the development of a viable industrial process using this novel yeast strain. Received 14 February 1998/ Accepted in revised form 19 May 1998     

Effects of ethanol concentration and stripping temperature on continuous fermentation rate

The operation of a pilot plant consisting of a 14-l fermentor, 10-cm packed column and condenser for continuous fermentation and stripping of ethanol was stable for more than 100 days. The feed consisted of a non-sterile solution of 560 g/l glucose with 100 g/l corn steep water. Fouling of the packing in the column with attached growth of yeast cells was controlled by in situ washing at intervals of 3–6 days. A computer simulation of the pilot plant was developed and used to analyze the data. The productivity of the continuous fermentor varied from 14 g ethanol to 17 g ethanol l⁻¹ h⁻¹. The yield was equal to the maximum theoretically possible: 0.51 g ethanol/g glucose consumed. Results are fit to linear models for the effects of ethanol concentration on specific growth rate and cell yield, and for the effect of stripping temperature on specific growth rate. Received: 16 October 1996 / Received revision: 3 January 1997 / Accepted: 24 January 1997     

Growth and bacteriocin production by Enterococcus faecium DPC1146 in batch and continuous culture

Production of the bacteriocin enterocin 1146 (E1146) by Enterococcus faecium DPC1146 was studied in batch and continuous fermentation. Growth was strongly inhibited by lactic acid. In batch fermentations maximum E1146 activity (2.8 MBU L⁻¹) was obtained in 9 h with 20 g L⁻¹ glucose. Increase in initial glucose concentration did not lead to a proportional increase in E1146 activity. A simple linear model was found to be adequate to explain the relationship between specific bacteriocin production rate and specific growth rate in batch fermentations with initial glucose concentration higher than 20 g L⁻¹. Maximum bacteriocin activity (2.9–3.2 MBU L⁻¹) was obtained in continuous fermentations at dilution rates between 0.12 and 0.17 h⁻¹ and specific bacteriocin production rate increased linearly with dilution rate. Received 31 July 1996/ Accepted in revised form 01 November 1996     

Benzene/toluene/p-xylene degradation. Part II. Effect of substrate interactions and feeding strategies in toluene/benzene and toluene/p-xylene fermentations in a partitioning bioreactor

A two-phase aqueous/organic partitioning bioreactor scheme was used to degrade mixtures of toluene and benzene, and toluene and p-xylene, using simultaneous and sequential feeding strategies. The aqueous phase of the partitioning bioreactor contained Pseudomonas sp. ATCC 55595, an organism able to degrade benzene, toluene and p-xylene simultaneously. An industrial grade of oleyl alcohol served as the organic phase. In each experiment, the organic phase of the bioreactor was loaded with 10.15 g toluene, and either 2.0 g benzene or 2.1 g p-xylene. The resulting aqueous phase concentrations were 50 mg/l, 25 mg/l and 8 mg/l toluene, benzene and p-xylene respectively. The simultaneous fermentation of benzene and toluene consumed these compounds at volumetric rates of 0.024 g l⁻¹ h⁻¹ and 0.067 g l⁻¹ h⁻¹, respectively. The simultaneous fermentation of toluene and p-xylene consumed these xenobiotics at volumetric rates of 0.066 g l⁻¹ h⁻¹ and 0.018 g l⁻¹ h⁻¹, respectively. A sequential feeding strategy was employed in which toluene was added initially, but the benzene or p-xylene aliquot was added only after the cells had consumed half of the initial toluene concentration. This strategy was shown to improve overall degradation rates, and to reduce the stress on the microorganisms. In the sequential fermentation of benzene and toluene, the volumetric degradation rates were 0.056 g l⁻¹ h⁻¹ and 0.079 g l⁻¹ h⁻¹, respectively. In the toluene/p-xylene sequential fermentation, the initial toluene load was consumed before the p-xylene aliquot was consumed. After 12 h in which no p-xylene degradation was observed, a 4.0-g toluene aliquot was added, and p-xylene degradation resumed. Excluding that 12-h period, the microbes consumed toluene and p-xylene at volumetric rates of 0.074 g l⁻¹ h⁻¹ and 0.025 g l⁻¹ h⁻¹, respectively. Oxygen limitation occurred in all fermentations during the rapid growth phase. Received: 16 November 1998 / Received revision: 29 March 1999 / Accepted: 9 April 1999     

Alcoholic fermentation of xylose and mixed sugars using recombinant <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> engineered for xylose utilization

Previously, a Saccharomyces cerevisiae strain was engineered for xylose assimilation by the constitutive overexpression of the Orpinomyces xylose isomerase, the S. cerevisiae xylulokinase, and the Pichia stipitis SUT1 sugar transporter genes. The recombinant strain exhibited growth on xylose, under aerobic conditions, with a specific growth rate of 0.025 h⁻¹, while ethanol production from xylose was achieved anaerobically. In the present study, the developed recombinant yeast was adapted for enhanced growth on xylose by serial transfer in xylose-containing minimal medium under aerobic conditions. After repeated batch cultivations, a strain was isolated which grew with a specific growth rate of 0.133 h⁻¹. The adapted strain could ferment 20 g l⁻¹ of xylose to ethanol with a yield of 0.37 g g⁻¹ and production rate of 0.026 g l⁻¹ h⁻¹. Raising the fermentation temperature from 30°C to 35°C resulted in a substantial increase in the ethanol yield (0.43 g g⁻¹) and production rate (0.07 g l⁻¹ h⁻¹) as well as a significant reduction in the xylitol yield. By the addition of a sugar complexing agent, such as sodium tetraborate, significant improvement in ethanol production and reduction in xylitol accumulation was achieved. Furthermore, ethanol production from xylose and a mixture of glucose and xylose was also demonstrated in complex medium containing yeast extract, peptone, and borate with a considerably high yield of 0.48 g g⁻¹.     

Xylitol production from D-xylose byCandida guillermondii: Fermentation behaviour

Summary The ability ofCandida guillermondii to produce xylitol from xylose and to ferment individual non xylose hemicellulosic derived sugars was investigated in microaerobic conditions. Xylose was converted into xylitol with a yield of 0,63 g/g and ethanol was produced in negligible amounts. The strain did not convert glucose, mannose and galactose into their corresponding polyols but only into ethanol and cell mass. By contrast, fermentation of arabinose lead to the formation of arabitol. On D-xylose medium,Candida guillermondii exhibited high yield and rate of xylitol production when the initial sugar concentration exceeded 110 g/l. A final xylitol concentration of 221 g/l was obtained from 300 g/l D-xylose with a yield of 82,6% of theoretical and an average specific rate of 0,19 g/g.h.Nomenclature Q_p average volumetric productivity of xylitol (g xylitol/l per hour) - q_p average specific productivity of xylitol (g xylitol/g of cells per hour) - So initial xylose concentration (g/l) - tf incubation time (hours) - Y_P/S xylitol yield (g of xylitol produced/g of xylose utilized) - Y_E/S ethanol yield (g of ethanol produced/g of substrate utilized) - Y_X/S cells yield (g of cells/g of substrate utilized) - specific growth rate coefficient (h^–1) - _max maximum specific growth rate coefficient (h^–1)     

Enhanced production of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) by fed-batch cultures of Pseudomonas sp EL-2

Pseudomonas sp EL-2 was cultivated to produce poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] from a structurally unrelated carbon source, glucose, by a fed-batch culture technique. Variation of the carbon to nitrogen (C/N) ratio of the medium produced optimal P(3HB-co-3HV) production at a C/N ratio of 95. Production of P(3HB-co-3HV) was favored by a dissolved oxygen tension of 40%. A maximum biomass concentration of 38 g L⁻¹ containing 53% P(3HB-co-3HV) was achieved after 45 h of cultivation. This corresponds to a volumetric productivity of 0.84 g L⁻¹ h⁻¹. The copolymer contained 7.5 mol% 3-hydroxyvalerate. Journal of Industrial Microbiology & Biotechnology (2000) 24, 36–40. Received 28 January 1999/ Accepted in revised form 11 September 1999