A Lithium Amide‐Borohydride Solid‐State Electrolyte with Lithium‐Ion Conductivities Comparable to Liquid Electrolytes

High ionic conductivity of up to 6.4 × 10^?3 S cm^?1 near room temperature (40 °C) in lithium amide‐borohydrides is reported, comparable to values of liquid organic electrolytes commonly employed in lithium‐ion batteries. Density functional theory is applied coupled with X‐ray diffraction, calorimetry, and nuclear magnetic resonance experiments to shed light on the conduction mechanism. A Li₄Ti₅O₁₂ half‐cell battery incorporating the lithium amide‐borohydride electrolyte exhibits good rate performance up to 3.5 mA cm^?2 (5 C) and stable cycling over 400 cycles at 1 C at 40 °C, indicating high bulk and interfacial stability. The results demonstrate the potential of lithium amide‐borohydrides as solid‐state electrolytes for high‐power lithium‐ion batteries.     

Li+ Pre‐Insertion Leads to Formation of Solid Electrolyte Interface on TiO2 Nanotubes That Enables High‐Performance Anodes for Sodium Ion Batteries

Recently, sodium ion batteries (SIBs) have been widely investigated as one of the most promising candidates for replacing lithium ion batteries (LIBs). For SIBs or LIBs, designing a stable and uniform solid electrolyte interphase (SEI) at the electrode–electrolyte interface is the key factor to provide high capacity, long‐term cycling, and high‐rate performance. In this paper, it is described how a remarkably enhanced SEI layer can be obtained on TiO₂ nanotube (TiO₂ NTs) arrays that allows for a strongly improved performance of sodium battery systems. Key is that a Li⁺ pre‐insertion in TiO₂ NTs can condition the SEI for Na⁺ replacement. SIBs constructed with Li‐pre‐inserted NTs deliver an exceptional Na⁺ cycling stability (e.g., 99.9 ± 0.1% capacity retention during 250 cycles at a current rate of 50 mA g^?1) and an excellent rate capability (e.g., 132 mA h g^?1 at a current rate of 1 A g^?1). The key factor in this outstanding performance is that Li‐pre‐insertion into TiO₂ NTs leads not only to an enhanced electronic conductivity in the tubes, but also expands the anatase lattice for facilitated subsequent Na⁺ cycling.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

Viscoelastic and Nonflammable Interface Design–Enabled Dendrite‐Free and Safe Solid Lithium Metal Batteries

Herein, a composite polymer electrolyte with a viscoelastic and nonflammable interface is designed to handle the contact issue and preclude Li dendrite formation. The composite polymer electrolyte (cellulose acetate/polyethylene glycol/Li_1.4Al_0.4Ti_1.6P₃O₁₂) exhibits a wide electrochemical window of 5 V (vs Li⁺/Li), a high Li⁺ transference number of 0.61, and an excellent ionic conductivity of above 10^?4 S cm^?1 at 60 °C. In particular, the intimate contact, low interfacial impedance, and fast ion‐transport process between the electrodes and solid electrolytes can be simultaneously achieved by the viscoelastic and nonflammable layer. Benefiting from this novel design, solid lithium metal batteries with either LiFePO₄ or LiCoO₂ as cathode exhibit superior cyclability and rate capability, such as a discharge capacity of 157 mA h g^?1 after 100 cycles at C/2 and 97 mA h g^?1 at 5C for LiFePO₄ cathode. Moreover, the smooth and uniform Li surface after long‐term cycling confirms the successful suppression of dendrite formation. The viscoelastic and nonflammable interface modification of solid electrolytes provides a promising and general strategy to handle the interfacial issues and improves the operative safety of solid lithium metal batteries.     

Countersolvent Electrolytes for Lithium‐Metal Batteries

Development of electrolytes that simultaneously have high ionic conductivity, wide electrochemical window, and lithium dendrite suppression ability is urgently required for high‐energy lithium‐metal batteries (LMBs). Herein, an electrolyte is designed by adding a countersolvent into LiFSI/DMC (lithium bis(fluorosulfonyl)amide/dimethyl carbonate) electrolytes, forming countersolvent electrolytes, in which the countersolvent is immiscible with the salt but miscible with the carbonate solvents. The solvation structure and unique properties of the countersolvent electrolyte are investigated by combining electroanalytical technology with a Molecular Dynamics simulation. Introducing the countersolvent alters the coordination shell of Li⁺ cations and enhances the interaction between Li⁺ cations and FSI^? anions, which leads to the formation of a LiF‐rich solid electrolyte interphase, arising from the preferential reduction of FSI^? anions. Notably, the countersolvent electrolyte suppresses Li dendrites and enables stable cycling performance of a Li||NCM622 battery at a high cut‐off voltage of 4.6 V at both 25 and 60 °C. This study provides an avenue to understand and design electrolytes for high‐energy LMBs in the future.     

An Anion‐Tuned Solid Electrolyte Interphase with Fast Ion Transfer Kinetics for Stable Lithium Anodes

The spatial distribution and transport characteristics of lithium ions (Li⁺) in the electrochemical interface region of a lithium anode in a lithium ion battery directly determine Li⁺ deposition behavior. The regulation of the Li⁺ solvation sheath on the solid electrolyte interphase (SEI) by electrolyte chemistry is key but challenging. Here, 1 m lithium trifluoroacetate (LiTFA) is induced to the electrolyte to regulate the Li⁺ solvation sheath, which significantly suppresses Li dendrite formation and enables a high Coulombic efficiency of 98.8% over 500 cycles. With its strong coordination between the carbonyl groups (C?O) and Li⁺, TFA^? modulates the environment of the Li⁺ solvation sheath and facilitates fast desolvation kinetics. In addition, due to relatively smaller lowest unoccupied molecular orbital energy than solvents, TFA^? has a preferential reduction to produce a stable SEI with uniform distribution of LiF and Li₂O. Such stable SEI effectively reduces the energy barrier for Li⁺ diffusion, contributing to low nucleation overpotential, fast ion transfer kinetics, and uniform Li⁺ deposition with high cycling stability. This work provides an alternative insight into the design of interface chemistry in terms of regulating anions in the Li⁺ solvation sheath. It is anticipated that this anion‐tuned strategy will pave the way to construct stable SEIs for other battery systems.     

Ultrathin,Flexible Polymer Electrolyte for Cost‐Effective Fabrication of All‐Solid‐State Lithium Metal Batteries

All‐solid‐state batteries are promising candidates for the next‐generation safer batteries. However, a number of obstacles have limited the practical application of all‐solid‐state Li batteries (ASSLBs), such as moderate ionic conductivity at room temperature. Here, unlike most of the previous approaches, superior performances of ASSLBs are achieved by greatly reducing the thickness of the solid‐state electrolyte (SSE), where ionic conductivity is no longer a limiting factor. The ultrathin SSE (7.5 µm) is developed by integrating the low‐cost polyethylene separator with polyethylene oxide (PEO)/Li‐salt (PPL). The ultrathin PPL shortens Li⁺ diffusion time and distance within the electrolyte, and provides sufficient Li⁺ conductance for batteries to operate at room temperature. The robust yet flexible polyethylene offers mechanical support for the soft PEO/Li‐salt, effectively preventing short‐circuits even under mechanical deformation. Various ASSLBs with PPL electrolyte show superior electrochemical performance. An initial capacity of 135 mAh g^?1 at room temperature and the high‐rate capacity up to 10 C at 60 °C can be achieved in LiFePO₄/PPL/Li batteries. The high‐energy‐density sulfur cathode and MoS₂ anode employing PPL electrolyte also realize remarkable performance. Moreover, the ASSLB can be assembled by a facile process, which can be easily scaled up to mass production.     

Polysulfide‐Shuttle Control in Lithium‐Sulfur Batteries with a Chemically/Electrochemically Compatible NaSICON‐Type Solid Electrolyte

A NaSICON‐type Li⁺‐ion conductive membrane with a formula of Li_{1+ x} Y _x Zr_{2? x} (PO₄)₃ (LYZP) (x = 0–0.15) has been explored as a solid‐electrolyte/separator to suppress polysulfide‐crossover in lithium‐sulfur (Li‐S) batteries. The LYZP membrane with a reasonable Li⁺‐ion conductivity shows both favorable chemical compatibility with the lithium polysulfide species and exhibits good electrochemical stability under the operating conditions of the Li‐S batteries. Through an integration of the LYZP solid electrolyte with the liquid electrolyte, the hybrid Li‐S batteries show greatly enhanced cyclability in contrast to the conventional Li‐S batteries with the porous polymer (e.g., Celgard) separator. At a rate of C/5, the hybrid Li ||LYZP|| Li₂S₆ batteries developed in this study (with a Li‐metal anode, a liquid/LYZP hybrid electrolyte, and a dissolved lithium polysulfide cathode) delivers an initial discharge capacity of ≈1000 mA h g^?1 (based on the active sulfur material) and retains ≈90% of the initial capacity after 150 cycles with a low capacity fade‐rate of <0.07% per cycle.     

Low‐Temperature Micro‐Solid Oxide Fuel Cells with Partially Amorphous La0.6Sr0.4CoO3‐δ Cathodes

Partially amorphous La_0.6Sr_0.4CoO_3‐δ (LSC) thin‐film cathodes are fabricated using pulsed laser deposition and are integrated in free‐standing micro‐solid oxide fuel cells (micro‐SOFC) with a 3YSZ electrolyte and a Pt anode. A low degree of crystallinity of the LSC layers is achieved by taking advantage of the miniaturization of the cells, which permits low‐temperature operation (300–450 °C). Thermomechanically stable micro‐SOFC are obtained with strongly buckled electrolyte membranes. The nanoporous columnar microstructure of the LSC layers provides a large surface area for oxygen incorporation and is also believed to reduce the amount of stress at the cathode/electrolyte interface. With a high rate of failure‐free micro‐SOFC membranes, it is possible to avoid gas cross‐over and open‐circuit voltages of 1.06 V are attained. First power densities as high as 200–262 mW cm^?2 at 400–450 °C are achieved. The area‐specific resistance of the oxygen reduction reaction is lower than 0.3 Ω cm² at 400 °C around the peak power density. These outstanding findings demonstrate that partially amorphous oxides are promising electrode candidates for the next‐generation of solid oxide fuel cells working at low‐temperatures.     

A Li2S‐TiS2‐Electrolyte Composite for Stable Li2S‐Based Lithium–Sulfur Batteries

Li₂S is a fully lithiated sulfur‐based cathode with a high theoretical capacity of 1166 mAh g^?1 that can be coupled with lithium‐free anodes to develop high‐energy‐density lithium–sulfur batteries. Although various approaches have been pursued to obtain a high‐performance Li₂S cathode, there are still formidable challenges with it (e.g., low conductivity, high overpotential, and irreversible polysulfide diffusion) and associated fabrication processes (e.g., insufficient Li₂S, excess electrolyte, and low reversible capacity), which have prevented the realization of high electrochemical utilization and stability. Here, a new cathode design composed of a homogeneous Li₂S‐TiS₂‐electrolyte composite that is prepared by a simple two‐step dry/wet‐mixing process is demonstrated, allowing the liquid electrolyte to wet the powder mixture consisting of insulating Li₂S and conductive TiS₂. The close‐contact, three‐phase boundary of this system improves the Li₂S‐activation efficiency and provides fast redox‐reaction kinetics, enabling the Li₂S‐TiS₂‐electrolyte cathode to attain stable cyclability at C/7 to C/3 rates, superior long‐term cyclability over 500 cycles, and promising high‐rate performance up to 1C rate. More importantly, this improved performance results from a cell design attaining a high Li₂S loading of 6 mg cm^?2, a high Li₂S content of 75 wt%, and a low electrolyte/Li₂S ratio of 6.     

A Sodium‐Ion Battery with a Low‐Cost Cross‐Linked Gel‐Polymer Electrolyte

The design of a sodium‐ion rechargeable battery with an antimony anode, a Na₃V₂(PO₄)₃ cathode, and a low‐cost composite gel‐polymer electrolyte based on cross‐linked poly(methyl methacrylate) is reported. The application of an antimony anode, on replacement of the sodium metal that is commonly used in sodium‐ion half‐cells, reduces significantly the interfacial resistance and charge transfer resistance of a sodium‐ion battery, which enables a smaller polarization for a sodium‐ion full‐cell Sb/Na₃V₂(PO₄)₃ running at relatively high charge and discharge rates. The incorporation of the gel‐polymer electrolyte is beneficial to maintain stable interfaces between the electrolyte and the electrodes of the sodium‐ion battery at elevated temperature. When running at 60 °C, the sodium‐ion full‐cell Sb/Na₃V₂(PO₄)₃ with the gel‐polymer electrolyte exhibits superior cycling stability compared to a battery with the conventional liquid electrolyte.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

Stable Seamless Interfaces and Rapid Ionic Conductivity of Ca–CeO2/LiTFSI/PEO Composite Electrolyte for High‐Rate and High‐Voltage All‐Solid‐State Battery

Stable and seamless interfaces among solid components in all‐solid‐state batteries (ASSBs) are crucial for high ionic conductivity and high rate performance. This can be achieved by the combination of functional inorganic material and flexible polymer solid electrolyte. In this work, a flexible all‐solid‐state composite electrolyte is synthesized based on oxygen‐vacancy‐rich Ca‐doped CeO₂ (Ca–CeO₂) nanotube, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), and poly(ethylene oxide) (PEO), namely Ca–CeO₂/LiTFSI/PEO. Ca–CeO₂ nanotubes play a key role in enhancing the ionic conductivity and mechanical strength while the PEO offers flexibility and assures the stable seamless contact between the solid electrolyte and the electrodes in ASSBs. The as‐prepared electrolyte exhibits high ionic conductivity of 1.3 × 10^?4 S cm^?1 at 60 °C, a high lithium ion transference number of 0.453, and high‐voltage stability. More importantly, various electrochemical characterizations and density functional theory (DFT) calculations reveal that Ca–CeO₂ helps dissociate LiTFSI, produce free Li ions, and therefore enhance ionic conductivity. The ASSBs based on the as‐prepared Ca–CeO₂/LiTFSI/PEO composite electrolyte deliver high‐rate capability and high‐voltage stability.     

Solvent‐Free Synthesis of Thin,Flexible, Nonflammable Garnet‐Based Composite Solid Electrolyte for All‐Solid‐State Lithium Batteries

Thin solid‐state electrolytes with nonflammability, high ionic conductivity, low interfacial resistance, and good processability are urgently required for next‐generation safe, high energy density lithium metal batteries. Here, a 3D Li_6.75La₃Zr_1.75Ta_0.25O₁₂ (LLZTO) self‐supporting framework interconnected by polytetrafluoroethylene (PTFE) binder is prepared through a simple grinding method without any solvent. Subsequently, a garnet‐based composite electrolyte is achieved through filling the flexible 3D LLZTO framework with a succinonitrile solid electrolyte. Due to the high content of garnet ceramic (80.4 wt%) and high heat‐resistance of the PTFE binder, such a composite electrolyte film with nonflammability and high processability exhibits a wide electrochemical window of 4.8 V versus Li/Li⁺ and high ionic transference number of 0.53. The continuous Li⁺ transfer channels between interconnected LLZTO particles and succinonitrile, and the soft electrolyte/electrode interface jointly contribute to a high ambient‐temperature ionic conductivity of 1.2 × 10^?4 S cm^?1 and excellent long‐term stability of the Li symmetric battery (stable at a current density of 0.1 mA cm^?2 for over 500 h). Furthermore, as‐prepared LiFePO₄|Li and LiNi_0.5Mn_0.3Co_0.2O₂|Li batteries based on the thin composite electrolyte exhibit high discharge specific capacities of 153 and 158 mAh g^?1 respectively, and desirable cyclic stabilities at room temperature.     

Slurry‐Fabricable Li+‐Conductive Polymeric Binders for Practical All‐Solid‐State Lithium‐Ion Batteries Enabled by Solvate Ionic Liquids

For mass production of all‐solid‐state lithium‐ion batteries (ASLBs) employing highly Li⁺ conductive and mechanically sinterable sulfide solid electrolytes (SEs), the wet‐slurry process is imperative. Unfortunately, the poor chemical stability of sulfide SEs severely restrict available candidates for solvents and in turn polymeric binders. Moreover, the binders interrupt Li⁺‐ionic contacts at interfaces, resulting in the below par electrochemical performance. In this work, a new scalable slurry fabrication protocol for sheet‐type ASLB electrodes made of Li⁺‐conductive polymeric binders is reported. The use of intermediate‐polarity solvent (e.g., dibromomethane) for the slurry allows for accommodating Li₆PS₅Cl and solvate‐ionic‐liquid‐based polymeric binders (NBR‐Li(G3)TFSI, NBR: nitrile?butadiene rubber, G3: triethylene glycol dimethyl ether, LiTFSI: lithium bis(trifluoromethanesulfonyl)imide) together without suffering from undesirable side reactions or phase separation. The LiNi_0.6Co_0.2Mn_0.2O₂ and Li₄Ti₅O₁₂ electrodes employing NBR‐Li(G3)TFSI show high capacities of 174 and 160 mA h g^?1 at 30 °C, respectively, which are far superior to those using conventional NBR (144 and 76 mA h g^?1). Moreover, high areal capacity of 7.4 mA h cm^?2 is highlighted for the LiNi_0.7Co_0.15Mn_0.15O₂ electrodes with ultrahigh mass loading of 45 mg cm^?2. The facilitated Li⁺‐ionic contacts at interfaces paved by NBR‐Li(G3)TFSI are evidenced by the complementary analysis from electrochemical and ⁷Li nuclear magnetic resonance measurements.     

In Situ Generated Fireproof Gel Polymer Electrolyte with Li6.4Ga0.2La3Zr2O12 As Initiator and Ion‐Conductive Filler

Poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP) based gel polymer electrolyte is regarded as a promising candidate to settle the safety issues of liquid electrolytes. However, the currently reported gel polymer electrolytes are still not safe enough owing to high amount of flammable liquid solvents contained in them. Herein, a fireproof PVDF‐HFP based gel polymer electrolyte is designed and synthesized through an in situ crosslinking method, with Li_6.4Ga_0.2La₃Zr₂O₁₂ as initiator and ion‐conductive filler. The obtained gel polymer electrolyte demonstrates superior fire resisting properties. The optimized gel polymer electrolyte exhibits an ionic conductivity as high as 1.84 × 10^?3 S cm^?1 at 20 °C with an electrochemical window up to 4.75 V at room temperature. Moreover, the obtained gel polymer electrolyte shows excellent compatibility with lithium anodes. Therefore, the lithium anode is well protected. Lithium batteries assembled with the gel polymer electrolyte possess superb safety properties in cutting and burning tests. Furthermore, the batteries also show a discharge retention rate as high as 94.08% (in comparison with the initial discharge capacity) after cycling at 0.5 C for 360 cycles with an average columbic efficiency higher than 98%. The purpose of this report is to show the great potential of applying fire‐retardant gel polymer electrolyte to achieve high safety lithium batteries.     

Facilitating Interfacial Stability Via Bilayer Heterostructure Solid Electrolyte Toward High‐energy,Safe and Adaptable Lithium Batteries

Solid‐state electrolytes are widely anticipated to enable the revival of high energy density and safe metallic Li batteries, however, their lower ionic conductivity at room temperature, stiff interfacial contact, and severe polarization during cycling continue to pose challenges in practical applications. Herein, a dual‐composite concept is applied to the design of a bilayer heterostructure solid electrolyte composed of Li⁺ conductive garnet nanowires (Li_6.75La₃Zr_1.75Nb_0.25O₁₂)/polyvinylidene fluoride‐co‐hexafluoropropylene (PVDF‐HFP) as a tough matrix and modified metal organic framework particles/polyethylene oxide/PVDF‐HFP as an interfacial gel. The integral ionic conductivity of the solid electrolyte reaches 2.0 × 10^?4 S cm^?1 at room temperature. In addition, a chemically/electrochemically stable interface is rapidly formed, and Li dendrites are well restrained by a robust inorganic shield and matrix. As a result, steady Li plating/stripping for more than 1700 h at 0.25 mA cm^?2 is achieved. Solid‐state batteries using this bilayer heterostructure solid electrolyte deliver promising battery performance (efficient capacity output and cycling stability) at ambient temperature (25 °C). Moreover, the pouch cells exhibit considerable flexibility in service and unexpected endurance under a series of extreme abuse tests including hitting with a nail, burning, immersion under water, and freezing in liquid nitrogen.     

A High‐Performance Monolithic Solid‐State Sodium Battery with Ca2+ Doped Na3Zr2Si2PO12 Electrolyte

Solid‐state sodium batteries (SSSBs) are promising electrochemical energy storage devices due to their high energy density, high safety, and abundant resource of sodium. However, low conductivity of solid electrolyte as well as high interfacial resistance between electrolyte and electrodes are two main challenges for practical application. To address these issues, pure phase Na₃Zr₂Si₂PO₁₂ (NZSP) materials with Ca²⁺ substitution for Zr⁴⁺ are synthesized by a sol‐gel method. It shows a high ionic conductivity of more than 10^?3 S cm^?1 at 25 °C. Moreover, a robust SSSB is developed by integrating sodium metal anodes into NZSP‐type monolithic architecture, forming a 3D electronic and ionic conducting network. The interfacial resistance is remarkably reduced and the monolithic symmetric cell displays stable sodium platting/striping cycles with low polarization for over 600 h. Furthermore, by combining sodium metal anode with Na₃V₂(PO₄)₃ cathode, an SSSB is demonstrated with high rate capability and excellent cyclability. After 450 cycles, the capacity of the cell is still kept at 94.9 mAh g^?1 at 1 C. This unique design of monolithic electrolyte architecture provides a promising strategy toward realizing high‐performance SSSBs.     

Ecofriendly Chemical Activation of Overlithiated Layered Oxides by DNA‐Wrapped Carbon Nanotubes

Despite their exceptionally high capacity, overlithiated layered oxides (OLO) have not yet been practically used in lithium‐ion battery cathodes due to necessary toxic/complex chemical activation processes and unsatisfactory electrochemical reliability. Here, a new class of ecofriendly chemical activation strategy based on amphiphilic deoxyribose nucleic acid (DNA)‐wrapped multiwalled carbon nanotubes (MWCNT) is demonstrated. Hydrophobic aromatic bases of DNA have a good affinity for MWCNT via noncovalent π–π stacking interactions, resulting in core (MWCNT)‐shell (DNA) hybrids (i.e., DNA@MWCNT) featuring the predominant presence of hydrophilic phosphate groups (coupled with Na⁺) in their outmost layers. Such spatially rearranged Na⁺–phosphate complexes of the DNA@MWCNT efficiently extract Li⁺ from monoclinic Li₂MnO₃ of the OLO through cation exchange reaction of Na⁺–Li⁺, thereby forming Li₄Mn₅O₁₂‐type spinel nanolayers on the OLO surface. The newly formed spinel nanolayers play a crucial role in improving the structural stability of the OLO and suppressing interfacial side reactions with liquid electrolytes, eventually providing significant improvements in the charge/discharge kinetics, cyclability, and thermal stability. This beneficial effect of the DNA@MWCNT‐mediated chemical activation is comprehensively elucidated by an in‐depth structural/electrochemical characterization.     

Interface‐Engineered All‐Solid‐State Li‐Ion Batteries Based on Garnet‐Type Fast Li+ Conductors

All‐solid‐state Li‐ion batteries based on Li₇La₃Zr₂O₁₂ (LLZO) garnet structures require novel electrode assembly strategies to guarantee a proper Li⁺ transfer at the electrode–electrolyte interfaces. Here, first stable cell performances are reported for Li‐garnet, c‐Li_6.25Al_0.25La₃Zr₂O₁₂, all‐solid‐state batteries running safely with a full ceramics setup, exemplified with the anode material Li₄Ti₅O₁₂. Novel strategies to design an enhanced Li⁺ transfer at the electrode–electrolyte interface using an interface‐engineered all‐solid‐state battery cell based on a porous garnet electrolyte interface structure, in which the electrode material is intimately embedded, are presented. The results presented here show for the first time that all‐solid‐state Li‐ion batteries with LLZO electrolytes can be reversibly charge–discharge cycled also in the low potential ranges (≈1.5 V) for combinations with a ceramic anode material. Through a model experiment, the interface between the electrode and electrolyte constituents is systematically modified revealing that the interface engineering helps to improve delivered capacities and cycling properties of the all‐solid‐state Li‐ion batteries based on garnet‐type cubic LLZO structures.