Heterojunction‐Depleted Lead‐Free Perovskite Solar Cells with Coarse‐Grained B‐γ‐CsSnI3 Thin Films

Perovskite solar cells (PSCs) have been emerging as a breakthrough photovoltaic technology, holding unprecedented promise for low‐cost, high‐efficiency renewable electricity generation. However, potential toxicity associated with the state‐of‐the‐art lead‐containing PSCs has become a major concern. The past research in the development of lead‐free PSCs has met with mixed success. Herein, the promise of coarse‐grained B‐γ‐CsSnI₃ perovskite thin films as light absorber for efficient lead‐free PSCs is demonstrated. Thermally‐driven solid‐state coarsening of B‐γ‐CsSnI₃ perovskite grains employed here is accompanied by an increase of tin‐vacancy concentration in their crystal structure, as supported by first‐principles calculations. The optimal device architecture for the efficient photovoltaic operation of these B‐γ‐CsSnI₃ thin films is identified through exploration of several device architectures. Via modulation of the B‐γ‐CsSnI₃ grain coarsening, together with the use of the optimal PSC architecture, planar heterojunction‐depleted B‐γ‐CsSnI₃ PSCs with power conversion efficiency up to 3.31% are achieved without the use of any additives. The demonstrated strategies provide guidelines and prospects for developing future high‐performance lead‐free PVs.     

Highly Air‐Stable Single‐Crystalline β‐CsPbI3 Nanorods: A Platform for Inverted Perovskite Solar Cells

The synthesis of single‐crystalline β‐CsPbI₃ perovskite nanorods (NRs) using a colloidal process is reported, exhibiting their improved photostability under 45–55% humidity. The crystal structure of CsPbI₃ NRs films is investigated using Rietveld refined X‐ray diffraction (XRD) patterns to determine crystallographic parameters and the phase transformation from orthorhombic (γ‐CsPbI₃) to tetragonal (β‐CsPbI₃) on annealing at 150 °C. Atomic resolution transmission electron microscopy images are utilized to determine the probable atomic distribution of Cs, Pb, and I atoms in a single β‐phase CsPbI₃ NR, in agreement with the XRD structure and selected area electron diffraction pattern, indicating the growth of single crystalline β‐CsPbI₃ NR. The calculation of the electronic band structure of tetragonal β‐CsPbI₃ using density functional theory (DFT) reveals a direct transition with a lower band gap and a higher absorption coefficient in the solar spectrum, as compared to its γ‐phase. An air‐stable (45–55% humidity) inverted perovskite solar cell, employing β‐CsPbI₃ NRs without any encapsulation, yields an efficiency of 7.3% with 78% enhancement over the γ‐phase, showing its potential for future low cost photovoltaic devices.     

Light‐Induced Degradation Mechanism in Poly(3‐hexylthiophene)/Fullerene Blend Solar Cells

The mechanism of light‐induced degradation in organic solar cells based on regioregular poly(3‐hexylthiophene) and indene‐C₆₀ bisadduct is studied by transient absorption (TA) and electron spin resonance (ESR) measurements. After 45 h light exposure under simulated solar illumination at 100 mW cm^?2, the short‐circuit current density, open‐circuit voltage, and fill factor are all degraded by about 20%–30% relative to the initial photovoltaic parameters. For the assignment of limiting conversion processes in the degraded solar cells, exciton diffusion into a donor/acceptor interface, charge transfer at the interface, charge dissociation into free charge carriers, and charge collection to each electrode are observed before and after the light exposure by the TA measurement. As a result, it is found that the charge collection deteriorates after the light exposure because of light‐induced charge trap formation in the bulk of the active layer. The origin of charge traps is further discussed on the basis of ESR measurements and density functional theory calculation.     

Investigating the Role of 4‐Tert Butylpyridine in Perovskite Solar Cells

The majority of hole‐transporting layers used in n‐i‐p perovskite solar cells contain 4‐tert butylpyridine (tBP). High power‐conversion efficiencies and, in particular, good steady‐state performance appears to be contingent on the inclusion of this additive. On the quest to improve the steady state efficiencies of the carbon nanotube‐based hole‐transporter system, this study has found that the presence of tBP results in an extraordinary improvement in the performance of these devices. By deconstructing a prototypical device and investigating the effect of tBP on each individual layer, the results of this study indicate that this performance enhancement must be due to a direct chemical interaction between tBP and the perovskite material. This study proposes that tBP serves to p‐dope the perovskite layer and investigates this theory with poling and work function measurements.     

Spiro‐Phenylpyrazole‐9,9′‐Thioxanthene Analogues as Hole‐Transporting Materials for Efficient Planar Perovskite Solar Cells

Perovskite solar cells have emerged as a promising technique for low‐cost, light weight, and highly efficient photovoltaics. However, they still largely rely on 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (Spiro‐OMeTAD) to serve as hole‐transporting materials (HTMs). Here, a series of HTMs with small molecular weight is designed, which are constructed on a spiro core involving phenylpyrazole and a second heteroaromatics, i.e., xanthene (O atom), thioxanthene (S atom), and acridine (N atom). Through varying from phenylpyrazole substituted xanthene ( PPyra‐XA ), thioxanthene ( PPyra‐TXA ), to acridine ( PPyra‐ACD ), their optical and electrochemical properties, hole mobilities, and the photovoltaic performance are optimized. As a consequence, PPyra‐TXA based device exhibits the highest power conversion efficiency (PCE) of 18.06%, outperforming that of Spiro‐OMeTAD (16.15%), which could be attributed to the enhancement of hole mobility exerted by the thioxanthene. In addition, the dopant‐free device shows PCE of 11.7%. These results open a new direction for designing spiro‐HTMs by simple modification of chemical structures.     

Thieno[3,4‐c]Pyrrole‐4,6‐Dione‐Based Polymer Acceptors for High Open‐Circuit Voltage All‐Polymer Solar Cells

While polymer acceptors are promising fullerene alternatives in the fabrication of efficient bulk heterojunction (BHJ) solar cells, the range of efficient material systems relevant to the “all‐polymer” BHJ concept remains narrow, and currently limits the perspectives to meet the 10% efficiency threshold in all‐polymer solar cells. This report examines two polymer acceptor analogs composed of thieno[3,4‐c ]pyrrole‐4,6‐dione (TPD) and 3,4‐difluorothiophene ([2F]T) motifs, and their BHJ solar cell performance pattern with a low‐bandgap polymer donor commonly used with fullerenes (PBDT‐TS1; taken as a model system). In this material set, the introduction of a third electron‐deficient motif, namely 2,1,3‐benzothiadiazole (BT), is shown to (i) significantly narrow the optical gap (E _opt) of the corresponding polymer (by ≈0.2 eV) and (ii) improve the electron mobility of the polymer by over two orders of magnitude in BHJ solar cells. In turn, the narrow‐gap P2TPDBT[2F]T analog (E _opt = 1.7 eV) used as fullerene alternative yields high open‐circuit voltages (V _OC) of ≈1.0 V, notable short‐circuit current values (J _SC) of ≈11.0 mA cm⁻², and power conversion efficiencies (PCEs) nearing 5% in all‐polymer BHJ solar cells. P2TPDBT[2F]T paves the way to a new, promising class of polymer acceptor candidates.     

Efficient Defect Passivation for Perovskite Solar Cells by Controlling the Electron Density Distribution of Donor‐π‐Acceptor Molecules

Organic–inorganic hybrid perovskite solar cells (PSCs) are a promising photovoltaic technology that has rapidly developed in recent years. Nevertheless, a large number of ionic defects within perovskite absorber can serve as non‐radiative recombination center to limit the performance of PSCs. Here, organic donor‐π‐acceptor (D‐π‐A) molecules with different electron density distributions are employed to efficiently passivate the defects in the perovskite films. The X‐ray photoelectron spectroscopy (XPS) analysis shows that the strong electron donating N,N‐dibutylaminophenyl unit in a molecule causes an increase in the electron density of the passivation site that is a carboxylate group, resulting in better binding with the defects of under‐coordinated Pb²⁺ cations. Carrier lifetime in the perovskite films measured by the time‐resolved photoluminescence spectrum is also prolonged by an increase in donation ability of the D‐π‐A molecules. As a consequence, these benefits contribute to an increase of 80 mV in the open circuit voltage of the devices, enabling a maximum power conversion efficiency (PCE) of 20.43%, in comparison with PCE of 18.52% for the control device. The authors' findings provide a novel strategy for efficient defect passivation in the perovskite solar cells based on controlling the electronic configuration of passivation molecules.     

Scaling Up ITO‐Free Solar Cells

Indium‐tin‐oxide‐free (ITO‐free) polymer solar cells with composite electrodes containing current‐collecting grids and a semitransparent poly(3,4‐ethylenedioxythiophene):polystyrenesulfonate) (PEDOT:PSS) conductor are demonstrated. The up‐scaling of the length of the solar cell from 1 to 6 cm and the effect of the grid line resistance are explored for a series of devices. Laser‐beam‐induced current (LBIC) mapping is used for quality control of the devices. A theoretical modeling study is presented that enables the identification of the most rational cell dimension for the grids with different resistances. The performance of ITO‐free organic solar cells with different dimensions and different electrode resistances are evaluated for different light intensities. The current generation and electric potential distribution are found to not be uniformly distributed in large‐area devices at simulated 1 Sun illumination. The generated current uniformity increases with decreasing light intensities.     

Efficiency Enhancement of Polymer Solar Cells Based on Poly(3‐hexylthiophene)/Indene‐C70 Bisadduct via Methylthiophene Additive

Photovoltaic performance of polymer solar cells based on poly(3‐hexylthiophene) (P3HT) as the donor and indene‐C₇₀ bisadduct (IC₇₀BA) as the acceptor is improved by adding 3 vol% 3‐methylthiophene (MT) or 3‐hexylthiophene (HT) as processing additives. The results of UV‐vis absorption spectroscopy, X‐ray diffraction analysis and atomic force microscopy indicate that with the MT or HT processing additive, the active layer of the blend of P3HT/IC₇₀BA showed strengthened absorbance, enhanced crystallinity and improved film morphology. The power conversion efficiency (PCE) of the PSCs was improved from 5.80% for the device without the additive to 6.35% for the device with HT additive and to 6.69% with MT additive. The PCE of 6.69% is the top value reported so far for the PSCs based on P3HT.