All Pseudocapacitive MXene‐RuO2 Asymmetric Supercapacitors

2D transition metal carbides and nitrides, known as MXenes, are an emerging class of 2D materials with a wide spectrum of potential applications, in particular in electrochemical energy storage. The hydrophilicity of MXenes combined with their metallic conductivity and surface redox reactions is the key for high‐rate pseudocapacitive energy storage in MXene electrodes. However, symmetric MXene supercapacitors have a limited voltage window of around 0.6 V due to possible oxidation at high anodic potentials. In this study, the fact that titanium carbide MXene (Ti₃C₂T_x) can operate at negative potentials in acidic electrolyte is exploited, to design an all‐pseudocapacitive asymmetric device by combining it with a ruthenium oxide (RuO₂) positive electrode. This asymmetric device operates at a voltage window of 1.5 V, which is about two times wider than the operating voltage window of symmetric MXene supercapacitors, and is the widest voltage window reported to date for MXene‐based supercapacitors. The complementary working potential windows of MXene and RuO₂, along with proton‐induced pseudocapacitance, significantly enhance the device performance. As a result, the asymmetric devices can deliver an energy density of 37 µW h cm^?2 at a power density of 40 mW cm^?2, with 86% capacitance retention after 20 000 charge–discharge cycles. These results show that pseudocapacitive negative MXene electrodes can potentially replace carbon‐based materials in asymmetric electrochemical capacitors, leading to an increased energy density.     

On‐Chip MXene Microsupercapacitors for AC‐Line Filtering Applications

Microsupercapacitors (MSCs) with high energy densities offer viable miniaturized alternatives to bulky electrolytic capacitors if the former can respond at the kilo Hertz (kHz) or higher frequencies. Moreover, MSCs fabricated on a chip can be integrated into thin‐film electronics in a compatible manner, serving the function of ripple filtering units or harvesters of energy from high‐frequency sources. In this work, wafer‐scale fabrication is demonstrated of MXene microsupercapacitors with controlled flake sizes and engineered device designs to achieve excellent frequency filtering performance. Specifically, the devices (100 nm thick electrodes and 10 µm interspace) deliver high volumetric capacitance (30 F cm^?3 at 120 Hz), high rate capability (300 V s^?1), and a very short relaxation time constant (τ₀ = 0.45 ms), surpassing conventional electrolytic capacitors (τ₀ = 0.8 ms). As a result, the devices are capable of filtering 120 Hz ripples produced by AC line power at a frequency of 60 Hz. This study opens new avenues for exploring miniaturized MXene MSCs as replacements for bulky electrolytic capacitors.     

MXene‐Contacted Silicon Solar Cells with 11.5% Efficiency

MXene, a new class of 2D materials, has gained significant attention owing to its attractive electrical conductivity, tunable work function, and metallic nature for wide range of applications. Herein, delaminated few layered Ti₃C₂T_x MXene contacted Si solar cells with a maximum power conversion efficiency (PCE) of ≈11.5% under AM1.5G illumination are demonstrated. The formation of an Ohmic junction of the metallic MXene to n⁺‐Si surface efficiently extracts the photogenerated electrons from n⁺np⁺‐Si, decreases the contact resistance, and suppresses the charge carrier recombination, giving rise to excellent open‐circuit voltage and short‐circuit current density. The rapid thermal annealing process further improves the electrical contact between Ti₃C₂T_x MXene and n⁺‐Si surface by reducing sheet resistance, increasing electrical conductivity, and decreasing cell series resistance, thus leading to a remarkable improvement in fill factor and overall PCE. The work demonstrated here can be extended to other MXene compositions as potential electrodes for developing highly performing solar cells.     

MXene—Conducting Polymer Asymmetric Pseudocapacitors

Conducting polymers (CPs) are attractive pseudocapacitive materials which show the highest capacitance under positive potentials in aqueous protic electrolytes. One way to expand their voltage window (thus energy density) in aqueous electrolytes is to manufacture asymmetric supercapacitors using distinctly different anodes. However, CPs lack matching pseudocapacitive anode materials that can perform well in protic electrolytes (e.g., sulfuric acid). 2D titanium carbide (Ti₃C₂T_x), MXene, as a universal pseudocapacitive anode material for a range of CPs, such as polyaniline, polypyrrole, and poly(3,4‐ethylenedioxythiophene) deposited on reduced graphene oxide (rGO) sheets, is reported here. All‐pseudocapacitive organic–inorganic asymmetric devices with MXene cathodes and rGO–polymer anodes can operate in voltage windows up to 1.45 V in 3 m H₂SO₄. Most importantly, these devices show outstanding cycling performance, outperforming many reported asymmetric pseudocapacitors.     

MXene‐Based Mesoporous Nanosheets Toward Superior Lithium Ion Conductors

Although solid polymer electrolytes have some intrinsic advantages in synthesis and film processing compared with inorganic solid electrolytes, low ionic conductivities and mechanical moduli hamper their practical applications in lithium‐based batteries. Here, an efficient strategy is developed to produce a unique solid polymer electrolyte containing MXene‐based mesoporous silica nanosheets with a sandwich structure, which are fabricated via controllable hydrolysis of tetraethyl orthosilicate around the surface of MXene‐Ti₃C₂ under the direction of cationic surfactants. Such unique nanosheets not only exhibit individual, thin, and insulated features, but also possess abundant functional groups in mesopores and on the surface, which are favorable for the formation of Lewis acid–base interactions with anions in polymer electrolytes such as poly(propylene oxide) elastomer, enabling the fast Li⁺ transportation at the mesoporous nanosheets/polymer interfaces. As a consequence, a solid polymer electrolyte with high ionic conductivity of 4.6 × 10^?4 S cm^?1, high Young's modulus of 10.5 MPa, and long‐term electrochemical stability is achieved.     

Femtosecond Laser‐Etched MXene Microsupercapacitors with Double‐Side Configuration via Arbitrary On‐ and Through‐Substrate Connections

The capacitance of microsupercapacitors (MSCs) can double if both sides of substrates are used to construct MSCs. Nevertheless, achieving electric connections of MSCs through substrates is a challenge due to the difficulty in precisely positioning each MSC couple that has two of the same MSCs units on two sides. In this work, taking advantage of the synchronous etching on both sides of transparent polyethylene terephthalate substrates by femtosecond laser pulses, a double‐sided configuration is attained with high precision in the alignment of back‐to‐back MSC couples and versatile double‐side MSCs are realized via arbitrary on‐ and through‐substrate connections of MXene MSC units. The MXene double‐side MSC fabricated by the series connection of 12 spiral pattern MXene MSC units with interdigital electrodes of 10 μm width interspace can output a large working voltage of 7.2 V. Additionally, femtosecond laser etching brings the transformation of MXene into titania near‐etched edges with a lateral distance less than 1 µm. Such a small laser‐affected area has little influence on the capacitive performance, which is one of advantages for femtosecond laser over conventional lasers. This research is valuable for one‐step manufacturing of highly integrated MSCs in the field of miniaturized energy storage systems.     

Large‐Scale Conductive Yarns Based on Twistable Korean Traditional Paper (Hanji) for Supercapacitor Applications: Toward High‐Performance Paper Supercapacitors

A simple and scalable method to fabricate a yarn‐type supercapacitor with a large specific capacitance without the aid of traditional pseudocapacitive electrode materials such as conducting polymers and metal oxides is reported. The yarn‐type supercapacitors are made from twisting reduced graphene oxide (rGO) or/and single‐walled carbon nanotubes (SWNTs)‐coated Korean traditional paper (KTP). The yarn‐type paper supercapacitor displays surprisingly enhanced electrochemical capacitance values, showing synergistic effect between rGO and SWNTs (500 times larger than performance of yarn‐type rGO‐coated paper supercapacitors). Coating rGO or/and SWNTs on KTP gives good morphology to the composite film, in which porosity increases and mean pore diameter decreases. The yarn‐type rGO/SWNT paper supercapacitor shows good mechanical strength, high flexibility, excellent electrochemical performance, and long‐life operation. The yarn‐type supercapacitor has an excellent electrochemical performance with a specific capacitance of 366 F g^?1 at scan rate of 25 mV s^?1 and high stability without any degradation in electrical performance up to 10 000 charge–discharge cycles. The average capacitance of rGO/SWNT@KTP yarn‐type supercapacitors is seven times higher than that of sheet‐type supercapacitors at scan rate of 500 mV s^?1. The lighting of a red light‐emitting diode (LED) is demonstrated by the yarn‐type paper supercapacitor without connecting supercapacitors in series.     

Low‐Temperature Reduction Strategy Synthesized Si/Ti3C2 MXene Composite Anodes for High‐Performance Li‐Ion Batteries

Silicon is attracting enormous attention due to its theoretical capacity of 4200 mAh g^?1 as an anode for Li‐ion batteries (LIBs). It is of fundamental importance and challenge to develop low‐temperature reaction route to controllably synthesize Si/Ti₃C₂ MXene LIBs anodes. Herein, a novel and efficient strategy integrating in situ orthosilicate hydrolysis and a low‐temperature reduction process to synthesize Si/Ti₃C₂ MXene composites is reported. The hydrolysis of tetraethyl orthosilicate leads to homogenous nucleation and growth of SiO₂ nanoparticles on the surface of Ti₃C₂ MXene. Subsequently, SiO₂ nanoparticles are reduced to Si via a low‐temperature (200 °C) reduction route. Importantly, Ti₃C₂ MXene not only provides fast transfer channels for Li⁺ and electrons, but also relieves volume expansion of Si during cycling. Moreover, the characteristics of excellent pseudocapacitive performance and high conductivity of Ti₃C₂ MXene can synergistically contribute to the enhancement of energy storage performance. As expected, Ti₃C₂/Si anode exhibits an outstanding specific capacity of 1849 mAh g^?1 at 100 mA g^?1, even retaining 956 mAh g^?1 at 1 A g^?1. The low‐temperature synthetic route to Si/Ti₃C₂ MXene electrodes and involved battery‐capacitive dual‐model energy storage mechanism has potential in the design of novel high‐performance electrodes for energy storage devices.     

A Three‐Dimensionally Interconnected Carbon Nanotube–Conducting Polymer Hydrogel Network for High‐Performance Flexible Battery Electrodes

High‐performance flexible energy‐storage devices have great potential as power sources for wearable electronics. One major limitation to the realization of these applications is the lack of flexible electrodes with excellent mechanical and electrochemical properties. Currently employed batteries and supercapacitors are mainly based on electrodes that are not flexible enough for these purposes. Here, a three‐dimensionally interconnected hybrid hydrogel system based on carbon nanotube (CNT)‐conductive polymer network architecture is reported for high‐performance flexible lithium ion battery electrodes. Unlike previously reported conducting polymers (e.g., polyaniline, polypyrrole, polythiophene), which are mechanically fragile and incompatible with aqueous solution processing, this interpenetrating network of the CNT‐conducting polymer hydrogel exibits good mechanical properties, high conductivity, and facile ion transport, leading to facile electrode kinetics and high strain tolerance during electrode volume change. A high‐rate capability for TiO₂ and high cycling stability for SiNP electrodes are reported. Typically, the flexible TiO₂ electrodes achieved a capacity of 76 mAh g^–1 in 40 s of charge/discharge and a high areal capacity of 2.2 mAh cm^–2 can be obtained for flexible SiNP‐based electrodes at 0.1C rate. This simple yet efficient solution process is promising for the fabrication of a variety of high performance flexible electrodes.     

Versatile N‐Doped MXene Ink for Printed Electrochemical Energy Storage Application

Printing is regarded as a revolutionary and feasible technique to guide the fabrication of versatile functional systems with designed architectures. 2D MXenes are nowadays attractive in printed energy storage devices. However, owing to the van der Waals interaction between the MXene layers, the restacking issues within the printed electrodes can significantly impede the ion/electrolyte transport and hence handicap the electrochemical performances. Herein, a melamine formaldehyde templating method is demonstrated to develop crumpled nitrogen‐doped MXene (MXene‐N) nanosheets. The nitrogen doping boosts the electrochemical performances of MXene via enhanced conductivity and redox activity. Accordingly, two types of MXene‐N inks are prepared throughout the optimization of the ink viscosity to fit the 2D screen printing and 3D extrusion printing, respectively. As a result, the screen printed MXene‐N microsupercapacitor delivers an areal capacitance of 70.1 mF cm^?2 and outstanding mechanical robustness. Furthermore, the 3D‐printed MXene‐N based supercapacitor manifests an areal capacitance of 8.2 F cm^?2 for a three‐layered electrode and readily stores a high areal energy density of 0.42 mWh cm^?2. The approach to harnessing such versatile MXene‐N inks offers distinctive insights into the printed energy storage systems with high areal energy density and large scalability.     

Graphitic Petal Electrodes for All‐Solid‐State Flexible Supercapacitors

The charge storage characteristics of a composite nanoarchitecture with a highly functional 3D morphology are reported. The electrodes are formed by the electropolymerization of aniline monomers into a nanometer‐thick polyaniline (PANI) film that conformally coats graphitic petals (GPs) grown by microwave plasma chemical vapor deposition (MPCVD) on conductive carbon cloth (CC). The hybrid CC/GPs/PANI electrodes yield results near the theoretical maximum capacitance for PANI of 2000 F g^?1 (based on PANI mass) and a large area‐normalized specific capacitance of ≈2.6 F cm^?2 (equivalent to a volumetric capacitance of ≈230 F cm^?3) at a low current density of 1 A g^?1 (based on PANI mass). The specific capacitances remain above 1200 F g^?1 (based on PANI mass) for currents up to 100 A g^?1 with correspondingly high area‐normalized values. The hybrid electrodes also exhibit a high rate capability with an energy density of 110 Wh kg^?1 and a maximum power density of 265 kW kg^?1 at a current density of 100 A g^?1. Long‐term cyclic stability is good (≈7% loss of initial capacitance after 2000 cycles), with coulombic efficiencies >99%. Moreover, prototype all‐solid‐state flexible supercapacitors fabricated from these hybrid electrodes exhibit excellent energy storage performance.     

Aqueous Solution‐Processable Small Molecular Metal‐Chelate Complex Electrolyte for Flexible All‐Solid State Energy Storage Devices

A small molecular metal‐chelate complex, tris(8‐hydroxyquinoline‐5‐sulfonic acid) aluminum (AlQSA₃), that has three sulfonic acid groups per molecule leading to an excellent solubility in water is reported as a liquid‐free perfect solid‐state electrolyte for flexible film‐type all‐solid‐state energy storage devices. The AlQSA₃ material is synthesized by one‐step reaction of aluminum triisopropoxide and 8‐hydroxyquinoline‐5‐sulfonic acid. The aqueous solutions of AlQSA₃ are applied to fabricate flexible film‐type all‐solid state electric double layer capacitors with indium‐tin oxide thin film electrodes. The ion conductivity of the AlQSA₃ film reaches 0.116 mS cm^?1, while a pronounced hysteresis are obtained in the cyclic voltammetry measurement. The AlQSA₃ film capacitors exhibit an output voltage of 1.5 V at 20 μA cm^?2, which is considerably stable by the repeated operation. In particular, the peak output voltage is well kept even after 180° bending for 500 times in the case of the flexible AlQSA₃ film capacitors.     

Combining Nature‐Inspired,Graphene‐Wrapped Flexible Electrodes with Nanocomposite Polymer Electrolyte for Asymmetric Capacitive Energy Storage

Two kinds of free‐standing electrodes, reduced graphene oxide (rGO)‐wrapped Fe‐doped MnO₂ composite (G‐MFO) and rGO‐wrapped hierarchical porous carbon microspheres composite (G‐HPC) are fabricated using a frozen lake‐inspired, bubble‐assistance method. This configuration fully enables utilization of the synergistic effects from both components, endowing the materials to be excellent electrodes for flexible and lightweight electrochemical capacitors. Moreover, a nonaqueous HPC‐doped gel polymer electrolyte (GPE‐HPC) is employed to broad voltage window and improve heat resistance. A fabricated asymmetric supercapacitor based on G‐MFO cathode and G‐HPC anode with GPE‐HPC electrolyte achieves superior flexibility and reliability, enhanced energy/power density, and outstanding cycling stability. The ability to power light‐emitting diodes also indicates the feasibility for practical use. Therefore, it is believed that this novel design may hold great promise for future flexible electronic devices.