Fundamental Understanding of Photocurrent Hysteresis in Perovskite Solar Cells

Organic–inorganic hybrid perovskite solar cells (PSCs) have become a promising candidate in the photovoltaic field due to their high power conversion efficiency and low material cost. However, the development of PSCs is limited by their poor stability under practical conditions in the presence of oxygen, moisture, sunlight, heat, and the current–voltage (I–V) hysteresis. In particular, the hysteretic I–V issue casts doubt on the validity of the photovoltaic performance results that are achieved, making it difficult to evaluate the authentic performance of PSCs. This review article focuses on understanding the I–V hysteresis behavior in PSCs and on exploring the possible reasons leading to this hysteresis phenomenon. The various strategies attempted to suppress the I–V hysteresis in PSCs are summarized, and a brief future recommendation is provided.     

Rationally Induced Interfacial Dipole in Planar Heterojunction Perovskite Solar Cells for Reduced J–V Hysteresis

With the rapid progress in developing hybrid perovskite solar cells, the allure of current density–voltage ( J–V) hysteresis has attracted quite a lot of interest in the research community. It requires feasible approaches that further deepen the fundamental understanding of device physics in specific device architecture in order to solve this problem eventually. Here, perovskite solar cells configured with different counter electrodes are systematically investigated with the focus on charge accumulation within the devices responsible for J–V hysteresis. The results indicate that J–V hysteresis is affected by charge accumulation which can be modulated by carrier extraction efficiency of the electrodes. Through a rationally induced interfacial dipole, the devices have shown improvement in carrier extraction, which thus reduces J–V hysteresis significantly. It provides solid evidence for the proposition that interface charge plays an important role in J–V hysteresis, and demonstrates an applicable strategy that effectively alleviates J–V hysteresis in perovskite solar cells.     

Alkali Chlorides for the Suppression of the Interfacial Recombination in Inverted Planar Perovskite Solar Cells

In this work, significant suppression of the interfacial recombination by facile alkali chloride interface modification of the NiOx hole transport layer in inverted planar perovskite solar cells is achieved. Experimental and theoretical results reveal that the alkali chloride interface modification results in improved ordering of the perovskite films, which in turn reduces defect/trap density, causing reduced interfacial recombination. This leads to a significant improvement in the open‐circuit voltage from 1.07 eV for pristine NiOx to 1.15 eV for KCl‐treated NiOx, resulting in a power conversion efficiency approaching 21%. Furthermore, the suppression of the ion diffusion in the devices is observed, as evidenced by stable photoluminescence (PL) under illumination and high PL quantum efficiency with alkali chloride treatment, as opposed to the luminescence enhancement and low PL quantum efficiency observed for perovskite on pristine NiOx. The suppressed ion diffusion is also consistent with improved stability of the devices with KCl‐treated NiOx. Thus, it is demonstrated that a simple interfacial modification is an effective method to not only suppress interfacial recombination but also to suppress ion migration in the layers deposited on the modified interface due to improved interface ordering and reduced defect density.     

Stability and Dark Hysteresis Correlate in NiO‐Based Perovskite Solar Cells

In perovskite solar cells (PSCs), the interfaces are a weak link with respect to degradation. Electrochemical reactivity of the perovskite's halides has been reported for both molecular and polymeric hole selective layers (HSLs), and here it is shown that also NiO brings about this decomposition mechanism. Employing NiO as an HSL in p–i–n PSCs with power conversion efficiency (PCE) of 16.8%, noncapacitive hysteresis is found in the dark, which is attributable to the bias‐induced degradation of perovskite/NiO interface. The possibility of electrochemically decoupling NiO from the perovskite via the introduction of a buffer layer is explored. Employing a hybrid magnesium‐organic interlayer, the noncapacitive hysteresis is entirely suppressed and the device's electrical stability is improved. At the same time, the PCE is improved up to 18% thanks to reduced interfacial charge recombination, which enables more efficient hole collection resulting in higher V_oc and FF.     

Recent Progresses on Defect Passivation toward Efficient Perovskite Solar Cells

The disorderly distribution of defects in the perovskite or at the grain boundaries, surfaces, and interfaces, which seriously affect carrier transport through the formation of nonradiative recombination centers, hinders the further improvement on the power conversion efficiency (PCE) of perovskite solar cells (PSCs). Several defect passivation strategies have been confirmed as an efficient approach for promoting the performance of PSCs. Herein, recent progress in the defect passivation toward efficient perovskite solar cells are summarized, and a classification of common passivation strategies that elaborate the mechanism according to the location of the defects and the type of passivation agent is presented. Finally, this review offers likely prospects for future trends in the development of passivation strategies.     

Interfaces in Perovskite Solar Cells

Rapid improvement in photoconversion efficiency (PCE) of solution processable organometallic hybrid halide based perovskite solar cells (PSCs) have taken the photovoltaic (PV) community with a surprise and has extended their application in other electronic devices such as light emitting diodes, photo detectors and batteries. Together with efforts to push the PCE of PSCs to record values >22% – now at par with that of crystalline silicon solar cells – origin of their PV action and underlying physical processes are also deeply investigated worldwide in diverse device configurations. A typical PSC consists of a perovskite film sandwiched between an electron and a hole selective contact thereby creating ESC/perovskite and perovskite/HSC interfaces, respectively. The selective contacts and their interfaces determine properties of perovskite layer and also control the performance, origin of PV action, open circuit voltage, device stability, and hysteresis in PSCs. Herein, we define ideal charge selective contacts, and provide an overview on how the choice of interfacing materials impacts charge accumulation, transport, transfer/recombination, band‐alignment, and electrical stability in PSCs. We then discuss device related considerations such as morphology of the selective contacts (planar or mesoporous), energetics and electrical properties (insulating and conducting), and its chemical properties (organic vs inorganic). Finally, the outlook highlights key challenges and future directions for a commercially viable perovskite based PV technology.     

Understanding and Eliminating Hysteresis for Highly Efficient Planar Perovskite Solar Cells

Through detailed device characterization using cross‐sectional Kelvin probe force microscopy (KPFM) and trap density of states measurements, we identify that the J–V hysteresis seen in planar organic–inorganic hybrid perovskite solar cells (PVSCs) using SnO₂ electron selective layers (ESLs) synthesized by low‐temperature plasma‐enhanced atomic‐layer deposition (PEALD) method is mainly caused by the imbalanced charge transportation between the ESL/perovskite and the hole selective layer/perovskite interfaces. We find that this charge transportation imbalance is originated from the poor electrical conductivity of the low‐temperature PEALD SnO₂ ESL. We further discover that a facile low‐temperature thermal annealing of SnO₂ ESLs can effectively improve the electrical mobility of low‐temperature PEALD SnO₂ ESLs and consequently significantly reduce or even eliminate the J–V hysteresis. With the reduction of J–V hysteresis and optimization of deposition process, planar PVSCs with stabilized output powers up to 20.3% are achieved. The results of this study provide insights for further enhancing the efficiency of planar PVSCs.     

Energetics and Energy Loss in 2D Ruddlesden–Popper Perovskite Solar Cells

2D Ruddlesden–Popper perovskites (RPPs) are emerging as potential challengers to their 3D counterpart due to superior stability and competitive efficiency. However, the fundamental questions on energetics of the 2D RPPs are not well understood. Here, the energetics at (PEA)₂(MA)_n?1Pb_nI_3n+1/[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) interfaces with varying n values of 1, 3, 5, 40, and ∞ are systematically investigated. It is found that n–n junctions form at the 2D RPP interfaces (n = 3, 5, and 40), instead of p–n junctions in the pure 2D and 3D scenarios (n = 1 and ∞). The potential gradient across phenethylammonium iodide ligands that significantly decreases surface work function, promotes separation of the photogenerated charge carriers with electron transferring from perovskite crystal to ligand at the interface, reducing charge recombination, which contributes to the smallest energy loss and the highest open‐circuit voltage (V_oc) in the perovskite solar cells (PSCs) based on the 2D RPP (n = 5)/PCBM. The mechanism is further verified by inserting a thin 2D RPP capping layer between pure 3D perovskite and PCBM in PSCs, causing the V_oc to evidently increase by 94 mV. Capacitance–voltage measurements with Mott–Schottky analysis demonstrate that such V_oc improvement is attributed to the enhanced potential at the interface.     

Understanding the Doping Effect on NiO: Toward High‐Performance Inverted Perovskite Solar Cells

High‐quality hole transport layers are prepared by spin‐coating copper doped nickel oxide (Cu:NiO) nanoparticle inks at room temperature without further processing. In agreement with theoretical calculations predicting that Cu doping results in acceptor energy levels closer to the valence band maximum compared to gap states of nickel vacancies in undoped NiO, an increase in the conductivity in Cu:NiO films compared to NiO is observed. Cu in Cu:NiO can be found in both Cu⁺ and Cu²⁺ states, and the substitution of Ni²⁺ with Cu⁺ contributes to both increased carrier concentration and carrier mobility. In addition, the films exhibit increased work function, which together with the conductivity increase, enables improved charge transfer and extraction. Furthermore, recombination losses due to lower monomolecular Shockley‐Read‐Hall recombination are reduced. These factors result in an improvement of all photovoltaic performance parameters and consequently an increased efficiency of the inverted planar perovskite solar cells. A power conversion efficiency (PCE) exceeding 20% could be achieved for small‐area devices, while PCE values of 17.41 and 18.07% are obtained for flexible devices and large area (1 cm²) devices on rigid substrates, respectively.     

Perovskite Solar Cells on the Way to Their Radiative Efficiency Limit – Insights Into a Success Story of High Open‐Circuit Voltage and Low Recombination

Inorganic‐organic lead‐halide perovskite solar cells have reached efficiencies above 22% within a few years of research. Achieved photovoltages of >1.2 V are outstanding for a material with a bandgap of 1.6 eV – in particular considering that it is solution processed. Such values demand for low non‐radiative recombination rates and come along with high luminescence yields when the solar cell is operated as a light emitting diode. This progress report summarizes the developments on material composition and device architecture, which allowed for such high photovoltages. It critically assesses the term “lifetime”, the theories and experiments behind it, and the different recombination mechanisms present. It attempts to condense reported explanations for the extraordinary optoelectronic properties of the material. Amongst those are an outstanding defect tolerance due to antibonding valence states and the capability of bandgap tuning, which might make the dream of low‐cost highly efficient solution‐processed thin film solar cells come true. Beyond that, the presence of photon recycling will open new opportunities for photonic device design.     

All‐Oxide MoOx/SnOx Charge Recombination Interconnects for Inverted Organic Tandem Solar Cells

Multijunction solar cells are designed to improve the overlap with the solar spectrum and to minimize losses due to thermalization. Aside from the optimum choice of photoactive materials for the respective sub‐cells, a proper interconnect is essential. This study demonstrates a novel all‐oxide interconnect based on the interface of the high‐work‐function (WF) metal oxide MoO_x and low‐WF tin oxide (SnO_x). In contrast to typical p‐/n‐type tunnel junctions, both the oxides are n‐type semiconductors with a WF of 5.2 and 4.2 eV, respectively. It is demonstrated that the electronic line‐up at the interface of MoO_x and SnO_x comprises a large intrinsic interface dipole (≈0.8 eV), which is key to afford ideal alignment of the conduction band of MoO_x and SnO_x, without the requirement of an additional metal or organic dipole layer. The presented MoO_x/SnO_x interconnect allows for the ideal (loss‐free) addition of the open circuit voltages of the two sub‐cells.     

Device Physics of Hybrid Perovskite Solar cells: Theory and Experiment

Perovskite solar cells (PSCs) exhibit a series of distinctive features in their optoelectronic response which have a crucial influence on the performance, particularly for long‐time response. Here, a survey of recent advances both in device simulation and optoelectronic and photovoltaic responses is provided, with the aim of comprehensively covering recent advances. Device simulations are included with clarifying discussions about the implications of classical drift–diffusion modeling and the inclusion of ionic charged layers near the outer carrier selective contacts. The outcomes of several transient techniques are summarized, along with the discussion of impedance and capacitive responses upon variation of bias voltage and irradiance level. In relation to the capacitive response, a discussion on the J–V curve hysteresis is also included. Although alternative models and explanations are included in the discussion, the review relies upon a key mechanism able to yield most of the rich experimental responses. Particularly for state‐of‐the‐art solar cells exhibiting efficiencies around or exceeding 20%, outer interfaces play a determining role on the PSC's performance. The ionic and electronic kinetics in the vicinity of the interfaces, coupled to surface recombination and carrier extraction mechanisms, should be carefully explored to progress further in performance enhancement.     

Inorganic Halide Perovskite Solar Cells: Progress and Challenges

All‐inorganic perovskite semiconductors have recently drawn increasing attention owing to their outstanding thermal stability. Although all‐inorganic perovskite solar cells (PSCs) have achieved significant progress in recent years, they still fall behind their prototype organic–inorganic counterparts owing to severe energy losses. Therefore, there is considerable interest in further improving the performance of all‐inorganic PSCs by synergic optimization of perovskite films and device interfaces. This review article provides an overview of recent progress in inorganic PSCs in terms of lead‐based and lead‐free composition. The physical properties of all‐inorganic perovskite semiconductors as well as the hole/electron transporting materials are discussed to unveil the important role of composition engineering and interface modification. Finally, a discussion of the prospects and challenges for all‐inorganic PSCs in the near future is presented.