Flexible Solar Thermal Fuel Devices: Composites of Fabric and a Photoliquefiable Azobenzene Derivative

Controllable storage and release of solar energy has always been a highlighted scientific issue for its benefit of mankind. Solar thermal fuels (STFs) supply a closed cycle and renewable energy‐storage strategy by transforming solar energy into chemical energy stored in the conformation of molecular isomers, such as cis/trans‐azobenzene, and releasing it as heat under various stimuli. Although the potential high energy density of the STFs which are based on the hybrids of azobenzene derivatives and carbon nanomaterials has been reported the solvent‐assistant charging hinders their practicability. In this study, a solid‐state STF device is designed and fabricated by compositing one photoliquefiable azobenzene (PLAZ) derivative with a flexible fabric template. The photoinduced phase transition of the PLAZ derivative enables the charging of the flexible STFs to be totally solvent‐free. Interestingly, the energy‐storage capacity (energy density ≈201 J g^?1) of flexible PLAZ STFs has been improved by the soft fabric template. The exothermic situation is monitored with one infrared camera, which shows 4 °C temperature difference between charged and discharged samples under blue light stimulus. The flexible STFs are may be used in practice as heating equipment.     

Liquid Norbornadiene Photoswitches for Solar Energy Storage

Due to high global energy demands, there is a great need for development of technologies for exploiting and storing solar energy. Closed cycle systems for storage of solar energy have been suggested, based on absorption of photons in photoresponsive molecules, followed by on‐demand release of thermal energy. These materials are called solar thermal fuels (STFs) or molecular solar thermal (MOST) energy storage systems. To achieve high energy densities, ideal MOST systems are required either in solid or liquid forms. In the case of the latter, neat high performing liquid materials have not been demonstrated to date. Here is presented a set of neat liquid norbornadiene derivatives for MOST applications and their characterization in toluene solutions and neat samples. Their synthesis is in most cases based on solvent‐free Diels‐Alder reactions, which easily and efficiently afford a range of compounds. The shear viscosity of the obtained molecules is close to that of colza oil, and they can absorb up to 10% of the solar spectrum with a measured energy storage density of up to 577 kJ/kg corresponding to 152 kJ mol^–1 (calculated 100 kJ mol^–1). These findings pave the way towards implementation of liquid norbornadienes in closed cycle energy storage technologies.     

Superior Performance of Microporous Aluminophosphate with LTA Topology in Solar‐Energy Storage and Heat Reallocation

Hydrophilic porous materials are recognized as very promising materials for water‐sorption‐based energy storage and transformation. In this study, a porous, zeolite‐like aluminophosphate with LTA (Linde Type A) topology is inspected as an energy‐storage material. The study is motivated by the material's high predicted pore volume. According to sorption and calorimetric tests, the aluminophosphate outperforms all other zeolite‐like and metal‐organic porous materials tested so far. It adsorbs water in an extremely narrow relative‐pressure interval (0.10 < p /p ₀ < 0.15) and exhibits superior water uptake (0.42 g g^?1) and energy‐storage capacity (527 kW h m^?3). It also shows remarkable cycling stability; after 40 cycles of adsorption/desorption its capacity drops by less than 2%. Desorption temperature for this material, which is one of crucial parameters in applications, is lower from desorption temperatures of other tested materials by 10–15 °C. Furthermore, its heat‐pump performance is very high, allowing efficient cooling in demanding conditions (with cooling power up to 350 kW h m^?3 even at 30 °C temperature difference between evaporator and environment). On the microscopic scale, sorption mechanism in AlPO₄‐LTA is elucidated by X‐ray diffraction, nuclear magnetic resonance measurements, and first‐principles calculations. In this aluminophosphate, energy is stored predominately in hydrogen‐bonded network of water molecules within the pores.     

Hexagonal Boron Nitride‐Based Electrolyte Composite for Li‐Ion Battery Operation from Room Temperature to 150 °C

Batteries for high temperature applications capable of withstanding over 60 °C are still dominated by primary cells. Conventional rechargeable energy storage technologies which have exceptional performance at ambient temperatures employ volatile electrolytes and soft separators, resulting in catastrophic failure under heat. A composite electrolyte/separator is reported that holds the key to extend the capability of Li‐ion batteries to high temperatures. A stoichiometric mixture of hexagonal boron nitride, piperidinium‐based ionic liquid, and a lithium salt is formulated, with ionic conductivity reaching 3 mS cm^?1, electrochemical stability up to 5 V and extended thermal stability. The composite is used in combination with conventional electrodes and demonstrates to be stable for over 600 cycles at 120 °C, with a total capacity fade of less than 3%. The ease of formulation along with superior thermal and electrochemical stability of this system extends the use of Li‐ion chemistries to applications beyond consumer electronics and electric vehicles.     

Ultrathin,Flexible Polymer Electrolyte for Cost‐Effective Fabrication of All‐Solid‐State Lithium Metal Batteries

All‐solid‐state batteries are promising candidates for the next‐generation safer batteries. However, a number of obstacles have limited the practical application of all‐solid‐state Li batteries (ASSLBs), such as moderate ionic conductivity at room temperature. Here, unlike most of the previous approaches, superior performances of ASSLBs are achieved by greatly reducing the thickness of the solid‐state electrolyte (SSE), where ionic conductivity is no longer a limiting factor. The ultrathin SSE (7.5 µm) is developed by integrating the low‐cost polyethylene separator with polyethylene oxide (PEO)/Li‐salt (PPL). The ultrathin PPL shortens Li⁺ diffusion time and distance within the electrolyte, and provides sufficient Li⁺ conductance for batteries to operate at room temperature. The robust yet flexible polyethylene offers mechanical support for the soft PEO/Li‐salt, effectively preventing short‐circuits even under mechanical deformation. Various ASSLBs with PPL electrolyte show superior electrochemical performance. An initial capacity of 135 mAh g^?1 at room temperature and the high‐rate capacity up to 10 C at 60 °C can be achieved in LiFePO₄/PPL/Li batteries. The high‐energy‐density sulfur cathode and MoS₂ anode employing PPL electrolyte also realize remarkable performance. Moreover, the ASSLB can be assembled by a facile process, which can be easily scaled up to mass production.     

Effects of hot water treatments and storage temperatures on the ripening and the use of electrical impedance as an index for assessing post-harvest changes in mango fruits

The effects of hot water treatment and storage temperature (4°C, 13°C or 22°C) on the quality and impedance of outer and inner mesocarp of mango were assessed in two experiments during storage, impedance being a potential non‐destructive measure of tissue damage following heat treatment. Fruits were subjected to equivalent heat units at 36.5°C for 60 min plus 46.5°C for 43 min or 46.5°C for 90 min by hot water treatments (hwt) on the assumption of cumulative heat effects and a base temperature of 12–13°C. Fruit reflectance decreased whereas chroma and hue angle increased over storage time and also with increase in storage temperature. The yellow colour increased with a rise in storage temperature in hot water treated mangoes. Soluble solids content of mangoes held at 22°C was highest at 5 days of storage but decreased subsequently over storage time. Impedance of all fruits decreased with increase in frequency, storage temperature and time in store. The impedance of hwt mangoes was lower than that of non‐hwt fruits 8 h after immersion, but recovered almost to control levels on day 5 at 4°C or 13°C, but decreased gradually after 5 days at 13°C. Impedance of all mangoes stored at 22°C decreased continuously during storage. Impedance was higher in the inner mesocarp than outer pulp. Impedance of hwt fruits was poorly correlated with soluble solid content and chroma but well correlated with reflectance of fruit pulp at 22°C. Changes in impedance of mangoes are discussed in relation to physiological and biochemical changes that occur during heat treatment and storage.     

An Ultrahigh Energy Density Quasi‐Solid‐State Zinc Ion Microbattery with Excellent Flexibility and Thermostability

The rapid development of smart wearable and integrated electronic products has urgently increased the requirement for high‐performance microbatteries. Although few lithium ion microbatteries based on organic electrolytes have been reported so far, the problems, such as undesirable energy density, poor flexibility, inflammability, volatility toxicity, and high cost restrict their practical applications in the above‐mentioned electronic products. In order to overcome these problems, a low cost quasi‐solid‐state aqueous zinc ion microbattery (ZIMB) assembled by a vanadium dioxide (B)‐multiwalled carbon nanotubes (VO₂ (B)‐MWCNTs) cathode, a zinc nanoflakes anode, and a zinc trifluoromethanesulfonate‐polyvinyl alcohol (Zn(CF₃SO₃)₂‐PVA) hydrogel electrolyte is exploited. As expected, the ZIMB exhibits excellent electrochemical performance, e.g., a high capacity of 314.7 µAh cm^?2, an ultrahigh energy density of 188.8 µWh cm^?2, and a high power density of 0.61 mW cm^?2. Furthermore, the ZIMB also shows high flexibility and excellent high temperature stability: the capacity has no obvious decay when the bending angle is up to 150° and the temperature reaches 100 °C. The ZIMB provides a way to develop next‐generation miniature energy storage devices with high performance.     

The size effect to O2−–Ce4+ charge transfer emission and band gap structure of Sr2CeO4

Sr₂CeO₄ phosphors with different crystalline sizes were synthesized by the sol–gel method or the solid‐state reaction. Their crystalline size, luminescence intensity of O^2??Ce⁴⁺ charge transfer and energy gaps were obtained through the characterization by X‐ray diffraction, photoluminescence spectra, as well as UV–visible diffuse reflectance measurements. An inverse relationship between photoluminescence (PL) spectra and crystalline size was observed when the heating temperature was from 1000°C to 1300°C. In addition, band energy calculated for all samples showed that a reaction temperature of 1200°C for the solid‐state method and 1100°C for sol–gel method gave the largest values, which corresponded with the smallest crystalline size. Correlation between PL intensity and crystalline size showed an inverse relationship. Band structure, density of states and partial density of states of the crystal were calculated to analyze the mechanism using the cambrige sequential total energy package (CASTEP) module integrated with Materials Studio software.     

Biomimetic MXene Textures with Enhanced Light‐to‐Heat Conversion for Solar Steam Generation and Wearable Thermal Management

2D materials are of particular interest in light‐to‐heat conversion, yet challenges remain in developing a facile method to suppress their light reflection. Herein, inspired by the black scales of Bitis rhinoceros, a generalized approach via sequential thermal actuations to construct biomimetic 2D‐material nanocoatings, including Ti₃C₂T_x MXene, reduced graphene oxide (rGO), and molybdenum disulfide (MoS₂) is designed. The hierarchical MXene nanocoatings result in broadband light absorption (up to 93.2%), theoretically validated by optical modeling and simulations, and realize improved light‐to‐heat performance (equilibrium temperature of 65.4 °C under one‐sun illumination). With efficient light‐to‐heat conversion, the bioinspired MXene nanocoatings are next incorporated into solar steam‐generation devices and stretchable solar/electric dual‐heaters. The MXene steam‐generation devices require much lower solar‐thermal material loading (0.32 mg cm^?2) and still guarantee high steam‐generation performance (1.33 kg m^?2 h^?1) compared with other state‐of‐the‐art devices. Additionally, the mechanically deformed MXene structures enable the fabrication of stretchable and wearable heaters dual‐powered by sunlight and electricity, which are reversibly stretched and heated above 100 °C. This simple fabrication process with effective utilization of active materials promises its practical application value for multiple solar–thermal technologies.     

Evidencing Excellent Thermal‐ and Photostability for Single‐Component Organic Solar Cells with Inherently Built‐In Microstructure

Solution‐processed organic solar cells (OSCs) are promising low‐cost, flexible, portable renewable sources for future energy supply. The state‐of‐the‐art OSCs are typically fabricated from a bulk‐heterojunction (BHJ) active layer containing well‐mixed donor and acceptor molecules in the nanometer regime. However, BHJ solar cells suffer from stability problems caused by the severe morphological changes upon thermal or illumination stress. In comparison, single‐component organic solar cells (SCOSCs) based on a double‐cable conjugated polymer with a covalently stabilized microstructure is suggested to be a key strategy for superior long‐term stability. Here, the thermal‐ and photostability of SCOSCs based on a model double‐cable polymer is systematically investigated. It is encouraging to find that under 90 °C & 1 sun illumination, the performance of SCOSCs remains substantially stable. Transport measurements show that charge generation and recombination (lifetime and recombination order) hardly change during the aging process. Particularly, the SCOSCs exhibit ultrahigh long‐term thermal stability with 100% PCE remaining after heating at temperature up to 160 °C for over 400 h, indicating an excellent candidate for extremely rugged applications.     

Safety‐Reinforced Poly(Propylene Carbonate)‐Based All‐Solid‐State Polymer Electrolyte for Ambient‐Temperature Solid Polymer Lithium Batteries

An integrated preparation of safety‐reinforced poly(propylene carbonate)‐based all‐solid polymer electrolyte is shown to be applicable to ambient‐temperature solid polymer lithium batteries. In contrast to pristine poly(ethylene oxide) solid polymer electrolyte, this solid polymer electrolyte exhibits higher ionic conductivity, wider electrochemical window, better mechanical strength, and superior rate performance at 20 °C. Moreover, lithium iron phosphate/lithium cell using such solid polymer electrolyte can charge and discharge even at 120 °C. It is also noted that the solid‐state soft‐package lithium cells assembled with this solid polymer electrolyte can still power a red light‐emitting diode lamp without suffering from internal short‐circuit failures even after cutting off one part of the battery. Considering the aspects mentioned above, the solid polymer electrolyte is eligible for practical lithium battery applications with improved reliability and safety. Just as important, a new perspective that the degree of amorphous state of polymer is also as critical as its low glass transition temperature for the exploration of room temperature solid polymer electrolyte is illustrated. In all, this study opens up a kind of new avenue that could be a milestone to the development of high‐voltage and ambient‐temperature all‐solid‐state polymer electrolytes.     

Protocols for dry DNA storage and shipment at room temperature

The globalization of DNA barcoding will require core analytical facilities to develop cost‐effective, efficient protocols for the shipment and archival storage of DNA extracts and PCR products. We evaluated three dry‐state DNA stabilization systems: commercial Biomatrica^® DNAstable^® plates, home‐made trehalose and polyvinyl alcohol (PVA) plates on 96‐well panels of insect DNA stored at 56 °C and at room temperature. Controls included unprotected samples that were stored dry at room temperature and at 56 °C, and diluted samples held at 4 °C and at ?20 °C. PCR and selective sequencing were performed over a 4‐year interval to test the condition of DNA extracts. Biomatrica^® provided better protection of DNA at 56 °C and at room temperature than trehalose and PVA, especially for diluted samples. PVA was the second best protectant after Biomatrica^® at room temperature, whereas trehalose was the second best protectant at 56 °C. In spite of lower PCR success, the DNA stored at ?20 °C yielded longer sequence reads and stronger signal, indicating that temperature is a crucial factor for DNA quality which has to be considered especially for long‐term storage. Although it is premature to advocate a transition to DNA storage at room temperature, dry storage provides an additional layer of security for frozen samples, protecting them from degradation in the event of freezer failure. All three forms of DNA preservation enable shipment of dry DNA and PCR products between barcoding facilities.     

Fatigue‐Free and Bending‐Endurable Flexible Mn‐Doped Na0.5Bi0.5TiO3‐BaTiO3‐BiFeO3 Film Capacitor with an Ultrahigh Energy Storage Performance

As the rapid development of intelligent systems moves toward flexible electronics, capacitors with extraordinary flexibility and an outstanding energy storage performance will open up broad prospects for powering portable/wearable electronics and pulsed power applications. This work presents a simple one‐step process to fabricate a flexible Mn‐doped 0.97(0.93Na_0.5Bi_0.5TiO₃‐0.07BaTiO₃)‐0.03BiFeO₃ (Mn:NBT‐BT‐BFO) inorganic thin film capacitor with the assistance of a 2D fluorophlogopite mica substrate. The film element, which has a high breakdown strength, great relaxor dispersion, and the coexistence of ferroelectric and antiferroelectric phases, has a high recoverable energy storage density (W_rec ≈81.9 J cm^?3), high efficiency (η ≈64.4%), superior frequency stability (500 Hz–20 kHz), excellent antifatigue property (1 × 10⁹ cycles), and a broad operating temperature window (25–200 °C). The all‐inorganic Mn:NBT‐BT‐BFO/Pt/mica capacitor has a prominent mechanical‐bending resistance without obvious deterioration in its corresponding energy storage capability when it is subjected to a bending radius of 2 mm or repeated bending for 10³ cycles. This work is the first demonstration of an all‐inorganic flexible film capacitor and sheds light on dielectric energy storage devices for portable/wearable applications.     

Grafting Benzenediazonium Tetrafluoroborate onto LiNixCoyMnzO2 Materials Achieves Subzero‐Temperature High‐Capacity Lithium‐Ion Storage via a Diazonium Soft‐Chemistry Method

Subzero‐temperature Li‐ion batteries (LIBs) are highly important for specific energy storage applications. Although the nickel‐rich layered lithium transition metal oxides(LiNi_xCo_yMn_zO₂) (LNCM) (x > 0.5, x + y +z = 1) are promising cathode materials for LIBs, their very slow Li‐ion diffusion is a main hurdle on the way to achieve high‐performance subzero‐temperature LIBs. Here, a class of low‐temperature organic/inorganic hybrid cathode materials for LIBs, prepared by grafting a conducting polymer coating on the surface of 3 µm sized LiNi_0.6Co_0.2Mn_0.2O₂ (LNCM‐3) material particles via a greener diazonium soft‐chemistry method is reported. Specifically, LNCM‐3 particles are uniformly coated with a thin polyphenylene film via the spontaneous reaction between LNCM‐3 and C₆H₅N₂⁺BF₄^?. Compared with the uncoated one, the polyphenylene‐coated LNCM‐3 (polyphenylene/LNCM‐3) has shown much improved low‐temperature discharge capacity (≈148 mAh g^?1 at 0.1 C, ?20 °C), outstanding rate capability (≈105 mAh g^?1 at 1 C, ?20 °C), and superior low‐temperature long‐term cycling stability (capacity retention is up to 90% at 0.5 C over 1150 cycles). The low‐temperature performance of polyphenylene/LNCM‐3 is the best among the reported state‐of‐the art cathode materials for LIBs. The present strategy opens up a new avenue to construct advanced cathode materials for wider range applications.     

A Lithium Amide‐Borohydride Solid‐State Electrolyte with Lithium‐Ion Conductivities Comparable to Liquid Electrolytes

High ionic conductivity of up to 6.4 × 10^?3 S cm^?1 near room temperature (40 °C) in lithium amide‐borohydrides is reported, comparable to values of liquid organic electrolytes commonly employed in lithium‐ion batteries. Density functional theory is applied coupled with X‐ray diffraction, calorimetry, and nuclear magnetic resonance experiments to shed light on the conduction mechanism. A Li₄Ti₅O₁₂ half‐cell battery incorporating the lithium amide‐borohydride electrolyte exhibits good rate performance up to 3.5 mA cm^?2 (5 C) and stable cycling over 400 cycles at 1 C at 40 °C, indicating high bulk and interfacial stability. The results demonstrate the potential of lithium amide‐borohydrides as solid‐state electrolytes for high‐power lithium‐ion batteries.     

Anatase TiO2 Confined in Carbon Nanopores for High‐Energy Li‐Ion Hybrid Supercapacitors Operating at High Rates and Subzero Temperatures

Li‐ion hybrid supercapacitors (Li‐HSCs) hold great promise in future electrical energy storage due to their relatively high power and energy density. However, a major challenge lies in the slow kinetics of Li‐ion intercalation/extraction within metal‐oxide electrodes. Here, it is shown that ultrafast charge storage is realized by confining anatase TiO₂ nanoparticles in carbon nanopores to enable a high‐rate anode for Li‐HSCs. The porous carbon with interconnected pore walls and open channels not only works as a conductive host to protect TiO₂ from structural degradation but also provides fast pathways for ion/electron transport. As a result, the assembled cells exhibit remarkable rate capabilities with a specific capacity of ≈140 mAh g^?1 at a slow charge and ≈60 mAh g^?1 at a 3.5 s fast charge. While the charge/discharge process can be completed as fast as that of state‐of‐the‐art electrical double‐layer capacitors (EDLCs), the produced nanocomposites show three to seven times higher volumetric capacitance than activated carbons used in commercial EDLCs with acetonitrile‐based electrolytes. Equally important for some applications in cold climates or the space, the Li‐HSCs can operate at subzero temperatures as low as ?40 °C, which is likely only limited by thermal properties of the acetonitrile (melting point of ?45 °C).     

A New Fe/V Redox Flow Battery Using a Sulfuric/Chloric Mixed‐Acid Supporting Electrolyte

A redox flow battery using Fe²⁺/Fe³⁺ and V²⁺/V³⁺ redox couples in chloric/sulfuric mixed‐acid supporting electrolyte is investigated for potential stationary energy storage applications. The Fe/V redox flow cell using mixed reactant solutions operates within a voltage window of 0.5–1.35 V with a nearly 100% utilization ratio and demonstrates stable cycling over 100 cycles with energy efficiency >80% and no capacity fading at room temperature. A 25% improvement in the discharge energy density of the Fe/V cell is achieved compared with a previously reported Fe/V cell using a pure chloride acid supporting electrolyte. Stable performance is achieved in the temperature range between 0 and 50 °C as well as when using a microporous separator as the membrane. The improved electrochemical performance makes the Fe/V redox flow battery a promising option as a stationary energy storage device to enable renewable integration and stabilization of the electric grid.     

Pyrolysis biochar systems,balance between bioenergy and carbon sequestration

This study aimed to investigate the extent to which it is possible to marry the two seemingly opposing concepts of heat and/or power production from biomass with carbon sequestration in the form of biochar. To do this, we investigated the effects of feedstock, highest heating temperature (HTT), residence time at HTT and carrier gas flow rate on the distribution of pyrolysis co‐products and their energy content, as well as the carbon sequestration potential of biochar. Biochar was produced from wood pellets (WP) and straw pellets (SP) at two temperatures (350 and 650 °C), with three residence times (10, 20 and 40 min) and three carrier gas flow rates (0, 0.33 and 0.66 l min^?1). The energy balance of the system was determined experimentally by quantifying the energy contained within pyrolysis co‐products. Biochar was also analysed for physicochemical and soil functional properties, namely environmentally stable‐C and labile‐C content. Residence time showed no considerable effect on any of the measured properties. Increased HTT resulted in higher concentrations of fixed C, total C and stable‐C in biochar, as well as higher heating value (HHV) due to the increased release of volatile compounds. Increased carrier gas flow rate resulted in decreased biochar yields and reduced biochar stable‐C and labile‐C content. Pyrolysis at 650 °C showed an increased stable‐C yield as well as a decreased proportion of energy stored in the biochar fraction but increased stored energy in the liquid and gas co‐products. Carrier gas flow rate was also seen to be influential in determining the proportion of energy stored in the gas phase. Understanding the influence of production conditions on long term biochar stability in addition to the energy content of the co‐products obtained from pyrolysis is critical for the development of specifically engineered biochar, be it for agricultural use, carbon storage, energy generation or combinations of the three.     

Preservation of Phakopsora pachyrhizi Uredospores

This study compared different temperatures and dormancy‐reversion procedures for preservation of Phakopsora pachyrhizi uredospores. The storage temperatures tested were room temperature, 5°C, ?20°C and ?80°C. Dehydrated and non‐dehydrated uredospores were used, and evaluations for germination (%) and infectivity (no. of lesions/cm²) were made with fresh harvested spores and after 15, 29, 76, 154 and 231 days of storage. The dormancy‐reversion procedures evaluated were thermal shock (40°C/5 min) followed or not by hydration (moist chamber/24 h). Uredospores stored at room temperature were viable only up to a month of storage, regardless of their hydration condition. Survival of uredospores increased with storage at lower temperatures. Dehydration of uredospores prior to storage increased their viability, mainly for uredospores stored at 5°C, ?20°C and ?80°C. At 5°C and ?20°C, dehydrated uredospores showed increases in viability of at least 47 and 127 days, respectively, compared to non‐dehydrated spores. Uredospore germination and infectivity after storage for 231 days (7.7 months), could only be observed at ?80°C, for both hydration conditions. At this storage temperature, dehydrated and non‐dehydrated uredospores exhibited 56 and 28% of germination at the end of the experiment, respectively. Storage at ?80°C also maintained uredospore infectivity, based upon levels of infection frequency, for both hydration conditions. Among the dormancy‐reversion treatments applied to spores stored at ?80°C, those involving hydration allowed recoveries of 85 to 92% of the initial germination.     

Low‐Operating Temperature,High‐Rate and Durable Solid‐State Sodium‐Ion Battery Based on Polymer Electrolyte and Prussian Blue Cathode

A solid‐state polymer electrolyte (PFSA‐Na membrane) for solid‐state sodium‐ion batteries (SSIBs) to overcome severe safety issues caused by traditional liquid electrolytes is explored. The PFSA‐Na membranes, synthesized by an environmentally and economically friendly method, display high ionic conductivity, excellent thermal stability, and outstanding mechanical flexibility in a wide temperature range. SSIBs based on the PFSA‐Na membranes and Prussian blue cathode exhibit a superior rate performance of 87.5 mA h g^?1 at 8 C and a durable cycling life of up to 1100 cycles at 1 C with only a slight capacity decay of ≈0.014% per cycle. Furthermore, due to the intrinsic advantages of the PFSA‐Na membranes, the cyclic performance of the proposed SSIBs is more stable than that of its liquid counterpart even at the rather low temperature of ?35 °C.