Charge Transport and Recombination in Low‐Bandgap Bulk Heterojunction Solar Cell using Bis‐adduct Fullerene

Charge transport and recombination are studied for organic solar cells fabricated using blends of polymer poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole)‐5,5′‐diyl] (Si‐PCPDTBT) with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (mono‐PCBM) and the bis‐adduct analogue of mono‐PCBM (bis‐PCBM). The photocurrent of Si‐PCPDTBT:bis‐PCBM devices shows a strong square root dependence on the effective applied voltage. From the relationship between the photocurrent and the light intensity, we found that the square‐root dependence of the photocurrent is governed by the mobility‐lifetime (μτ) product of charge carriers while space‐charge field effects are insignificant. The fill factor (FF) and short circuit current density (J_sc) of bis‐PCBM solar cells show a considerable increase with temperature as compared to mono‐PCBM solar cells. SCLC analysis of single carrier devices proofs that the mobility of both electrons and holes is significantly lowered when replacing mono‐PCBM with bis‐PCBM. The increased recombination in Si‐PCPDTBT:bis‐PCBM solar cells is therefore attributed to the low carrier mobilities, as the transient photovoltage measurements show that the carrier lifetime of devices are not significantly altered by using bis‐PCBM instead of mono‐PCBM.     

Triplet Excitons in Highly Efficient Solar Cells Based on the Soluble Small Molecule p‐DTS(FBTTh2)2

Triplet exciton formation in neat 7,7‐(4,4‐bis(2‐ethylhexyl)‐4H‐silolo[3,2‐b:4,5‐b′] dithiophene‐2,6‐diyl)bis(6‐fluoro‐4‐(5′‐hexyl‐[2,2′‐bithiophen]‐5‐yl)benzo[c][1,2,5]thiadiazole) (p‐DTS(FBTTh₂)₂) and blends with [6,6]‐Phenyl C₇₀ butyric acid methyl ester (PC₇₀BM), with and without the selective solvent additive 1,8‐diiodooctane, is investigated by means of spin sensitive photoluminescence measurements. For all three material systems, a significant amount of long living triplet excitons is detected, situated on the p‐DTS(FBTTh₂)₂ molecules. The characteristic zero‐field splitting parameters for this state are identified to be D = 42 mT (1177 MHz) and E = 5 mT (140 MHz). However, no triplet excitons located on PC₇₀BM are detectable. Using electrically detected spin resonance, the presence of these triplet excitons is confirmed even at room temperature, highlighting that triplet excitons form during solar cell operation and influence the photocurrent and photovoltage. Surprisingly, the superior performing blend is found to have the largest triplet population. It is concluded, that the formation of triplet excitons from charge transfer states via electron back transfer has no crucial impact on device performance in p‐DTS(FBTTh₂)₂:PC₇₀BM based solar cells.     

Controlling Hierarchy in Solution‐processed Polymer Solar Cells Based on Crosslinked P3HT

Understanding and controlling the morphology of donor/acceptor blends is critical for the development of solution processable organic solar cells. By crosslinking a poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) film we have been able to spin‐coat [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) onto the film to form a structure that is close to a bilayer, thus creating an ideal platform for investigating interdiffusion in this model system. Neutron reflectometry (NR) demonstrates that without any thermal treatment a smaller amount of PCBM percolates throughout the crosslinked P3HT when compared to a non‐crosslinked P3HT film. Using time‐resolved NR we also show thermal annealing increases the rate of diffusion, resulting in a near‐uniform distribution of PCBM throughout the polymer film. XPS measurements confirm the presence of both P3HT and PCBM at the annealed film's surface indicating that the two components are intermixed. Photovoltaic devices fabricated using this bilayer approach and suitable annealing conditions yielded comparable power conversion efficiencies to bulk heterojunction devices made from the same materials. The crosslinking procedure has also enabled the formation of patterned P3HT films by photolithography. Pillars with feature sizes down to 2 μm were produced and after subsequent deposition of PCBM and thermal annealing devices with efficiencies of up to 1.4% were produced.     

Enhanced Photovoltaic Performance of Amorphous Donor–Acceptor Copolymers Based on Fluorine‐Substituted Benzodioxocyclohexene‐Annelated Thiophene

Donor–acceptor (D‐A) type π‐conjugated copolymers with crystalline behavior have been extensively investigated as donor semiconductors in organic photovoltaics (OPVs). On the other hand, the development of high‐performance amorphous donor materials is still behind. The amorphous donor copolymer DTS‐C₀(F₂) consisting of dithieno[3,2‐b:2′,3′‐d]silole ( DTS ) donor unit and the recently developed fluorine‐substituted naphtho[2,3‐c]thiophene‐4,9‐dione ( C₀(F₂) ) acceptor unit shows moderate photovoltaic performance upon blending with PC₇₁BM. In this work, to enhance the hole‐transporting characteristics, a 3‐hexylthiophene ( HT ) spacer unit is integrated into the conjugated backbone, resulting in a new amorphous copolymer DTS‐HT‐C₀(F₂) . The strong electron‐accepting nature of C₀(F₂) allows the introduction of the HT spacer without affecting the frontier orbital energies and thus the D‐A character. Without using solvent additives and thermal annealing, OPVs based on DTS‐HT‐C₀(F₂) and [6,6]‐phenyl‐C71‐butyric acid methyl ester PC₇₁BM show an improved power conversion efficiency of 9.12%. Investigation of the device physics unambiguously reveals that the hole mobility of the copolymer in the blend is increased by an order of magnitude by the introduction of HT , while keeping an amorphous film nature, leading to higher short‐circuit current density and fill factor. These results demonstrate the realization of high‐performance OPVs based on amorphous active layers.     

The Effect of PCBM Dimerization on the Performance of Bulk Heterojunction Solar Cells

Increasing the lifetime of polymer based organic solar cells is still a major challenge. Here, the photostability of bulk heterojunction solar cells based on the polymer poly[4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐[2,5‐bis(3‐tetradecylthiophen‐2‐yl)thiazole[5,4‐d]thiazole)‐1,8‐diyl] (PDTSTzTz) and the fullerene [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₀BM) under inert atmosphere is investigated. Correlation of electrical measurements on complete devices and UV‐vis absorption measurements as well as high‐performance liquid chromatography (HPLC) analysis on the active materials reveals that photodimerization of PC₆₀BM is responsible for the observed degradation. Simulation of the electrical device parameters shows that this dimerization results in a significant reduction of the charge carrier mobility. Both the dimerization and the associated device performance loss turn out to be reversible upon annealing. BisPC₆₀BM, the bis‐substituted analog of PC₆₀BM, is shown to be resistant towards light exposure, which in turn enables the manufacture of photostable PDTSTzTz:bisPC₆₀BM solar cells.     

Sequential Processing for Organic Photovoltaics: Design Rules for Morphology Control by Tailored Semi‐Orthogonal Solvent Blends

Design rules are presented for significantly expanding sequential processing (SqP) into previously inaccessible polymer:fullerene systems by tailoring binary solvent blends for fullerene deposition. Starting with a base solvent that has high fullerene solubility, 2‐chlorophenol (2‐CP), ellipsometry‐based swelling experiments are used to investigate different co‐solvents for the fullerene‐casting solution. By tuning the Flory‐Huggins χ parameter of the 2‐CP/co‐solvent blend, it is possible to optimally swell the polymer of interest for fullerene interdiffusion without dissolution of the polymer underlayer. In this way solar cell power conversion efficiencies are obtained for the PTB7 (poly[(4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)(3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl)]) and PC₆₁BM (phenyl‐C₆₁‐butyric acid methyl ester) materials combination that match those of blend‐cast films. Both semicrystalline (e.g., P3HT (poly(3‐hexylthiophene‐2,5‐diyl)) and entirely amorphous (e.g., PSDTTT (poly[(4,8‐di(2‐butyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)‐alt‐(2,5‐bis(4,4′‐bis(2‐octyl)dithieno[3,2‐b:2′3′‐d]silole‐2,6‐diyl)thiazolo[5,4‐d]thiazole)]) conjugated polymers can be processed into highly efficient photovoltaic devices using the solvent‐blend SqP design rules. Grazing‐incidence wide‐angle x‐ray diffraction experiments confirm that proper choice of the fullerene casting co‐solvent yields well‐ordered interdispersed bulk heterojunction (BHJ) morphologies without the need for subsequent thermal annealing or the use of trace solvent additives (e.g., diiodooctane). The results open SqP to polymer/fullerene systems that are currently incompatible with traditional methods of device fabrication, and make BHJ morphology control a more tractable problem.     

High Fill Factor Polymer Solar Cells Incorporating a Low Temperature Solution Processed WO3 Hole Extraction Layer

We demonstrate solution‐processed tungsten trioxide (WO₃) incorporated as hole extraction layer (HEL) in polymer solar cells (PSCs) with active layers comprising either poly(3‐hexylthiophene) (P3HT) or poly[(4,4'‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole)‐5,50‐diyl] (Si‐PCPDTBT) mixed with a fullerene derivative. The WO₃ layers are deposited from an alcohol‐based, surfactant‐free nanoparticle solution. A short, low‐temperature (80 °C) annealing is sufficient to result in fully functional films without the need for an oxygen‐plasma treatment. This allows the application of the WO₃ buffer layer in normal as well as inverted architecture solar cells. Normal architecture devices based on WO₃ HELs show comparable performance to the PEDOT:PSS reference devices with slightly better fill factors and open circuit voltages. Very high shunt resistances (over 1 MΩ cm²) and excellent diode rectification underline the charge selectivity of the solution‐processed WO₃ layers.     

Germanium‐ and Silicon‐Substituted Donor–Acceptor Type Copolymers: Effect of the Bridging Heteroatom on Molecular Packing and Photovoltaic Device Performance

The effects of heteroatom substitution from a silicon atom to a germanium atom in donor‐acceptor type low band gap copolymers, poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (PSiBTBT) and poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]germole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (PGeBTBT), are studied. The optoelectronic and charge transport properties of these polymers are investigated with a particular focus on their use for organic photovoltaic (OPV) devices in blends with phenyl‐C₇₀‐butyric acid methyl ester (PC₇₀BM). It is found that the longer C‐Ge bond length, in comparison to C‐Si, modifies the molecular conformation and leads to a more planar chain conformation in PGeBTBT than PSiBTBT. This increase in molecular planarity leads to enhanced crystallinity and an increased preference for a face‐on backbone orientation, thus leading to higher charge carrier mobility in the diode configuration. These results provide important insight into the impact of the heavy atom substitution on the molecular packing and device performance of polymers based on the poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b]‐dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole) (PCPDTBT) backbone.     

Selective Dye Loading at the Heterojunction in Polymer/Fullerene Solar Cells

Selective dye loading at the polymer/fullerene interface was studied for ternary blend bulk heterojunction solar cells, consisting of regioregular poly(3‐hexylthiophene) (RR‐P3HT), a fullerene derivative (PCBM), and a silicon phthalocyanine derivative (SiPc) as a light‐harvesting dye. The photocurrent density and power conversion efficiency of the ternary blend solar cells were most improved by loading SiPc with a content of 4.8 wt%. The absorption and surface energy measurements suggested that SiPc is located in the disordered P3HT domains at the RR‐P3HT/PCBM interface rather than in the PCBM and crystal P3HT domains. From the peak wavelength of SiPc absorption, the local concentration of SiPc ([SiPc]_Local) was estimated for the RR‐P3HT:PCBM:SiPc ternary blends. Even for amorphous films of regiorandom P3HT (RRa‐P3HT) blended with PCBM and SiPc, [SiPc]_Local was higher than the original content, suggesting dye segregation into the RRa‐P3HT/PCBM interface. For RR‐P3HT:PCBM:SiPc blends, [SiPc]_Local increased with the increase in the P3HT crystallinity. Such interfacial segregation of dye molecules in ternary blend films can be rationally explained in terms of the surface energy of each component and the crystallization of P3HT being enhanced by annealing. Notably, the solvent annealing effectively segregated dye molecules into the interface without the formation of PCBM clusters.     

Electron Collection as a Limit to Polymer:PCBM Solar Cell Efficiency: Effect of Blend Microstructure on Carrier Mobility and Device Performance in PTB7:PCBM

The poor photovoltaic performance of state‐of‐the‐art blends of poly[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl] (PTB7) and [6,6]‐phenyl‐C61‐butyric acid (PCBM) at large active layer thicknesses is studied using space‐charge‐limited current mobility and photovoltaic device measurements. The poor performance is found to result from relatively low electron mobility. This is attributed to the low tendency of PTB7 to aggregate, which reduces the ability of the fullerene to form a connected network. Increasing the PCBM content 60–80 wt% increases electron mobility and accordingly improves performance for thicker devices, resulting in a fill factor (FF) close to 0.6 at 300 nm. The result confirms that by improving only the connectivity of the fullerene phase, efficient electron and hole collection is possible for 300 nm‐thick PTB7:PCBM devices. Furthermore, it is shown that solvent additive 1,8‐diiodooctane (DIO), used in the highest efficiency PTB7:PCBM devices, does not improve the thickness dependence and, accordingly, does not lead to an increase in either hole or electron mobility or in the carrier lifetime. A key challenge for researchers is therefore to develop new methods to ensure connectivity in the fullerene phase in blends without relying on either a large excess of fullerene or strong aggregation of the polymer.     

Significance of Average Domain Purity and Mixed Domains on the Photovoltaic Performance of High‐Efficiency Solution‐Processed Small‐Molecule BHJ Solar Cells

Whereas the role of molecularly mixed domains in organic photovoltaic devices for charge generation is extensively discussed in the literature, the impact on charge recombination and thus fill factor is largely unexplored. Here, a combination of soft X‐ray techniques enables the quantification of phases at multiple length scales to reveal their role regarding charge recombination in a highly efficient solution processed small molecule system 7,7′‐(4,4‐bis(2‐ethylhexyl)‐4H‐silolo[3,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)bis(6‐fluoro‐4‐(5′‐hexyl‐[2,2′‐bithiophen]‐5‐yl)benzo[c][1,2,5]thiadiazole) (p‐DTS(FBTTh₂)₂) . A quantitative (linear) relationship between the average composition variations and the device fill‐factor is observed. The results establish the complex interrelationship between average phase purity, domain size, and structural order and highlight the requirement of achieving sufficient phase purities to diminish bimolecular and geminate recombination in solution processed small molecule solar cells.     

Work Function Control of Interfacial Buffer Layers for Efficient and Air‐Stable Inverted Low‐Bandgap Organic Photovoltaics

A water‐soluble cationic polythiophene derivative, poly[3‐(6‐{4‐tert‐butylpyridiniumyl}‐hexyl)thiophene‐2,5‐diyl] [P3(TBP)HT], is combined with anionic poly(3,4‐ethylenedioxythiophene):poly(p‐styrenesulfonate) (PEDOT:PSS) on indium tin oxide (ITO) substrates via electrostatic layer‐by‐layer (eLbL) assembly. By varying the number of eLbL layers, the electrode's work function is precisely controlled from 4.6 to 3.8 eV. These polymeric coatings are used as cathodic interfacial modifiers for inverted‐mode organic photovoltaics that incorporate a photoactive layer composed of either poly[(3‐hexylthiophene)‐2,5‐diyl] (P3HT) and the fullerene acceptor [6,6‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or the low bandgap polymer [poly({4,8‐di(2‐ethylhexyloxyl)benzo[1,2‐b:4,5‐b′]dithiophene}‐2,6‐diyl)‐alt‐({5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}‐1,3‐diyl) (PBDTTPD)] and the electron acceptor [6,6‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM)]. The power conversion efficiency (PCE) of the resulting photovoltaic device is dependent on the composition of the eLbL‐assembled interface and permits the fabrication of devices with efficiencies of 3.8% and 5.6% for P3HT and PBDTTPD donor polymers, respectively. Notably, these devices demonstrate significant stability with a P3HT:PC₆₁BM system maintaining 83% of its original PCE after 1 year of storage and a PBDTTPD:PC₇₁BM system maintaining 97% of its original PCE after over 1000 h of storage in air, according to the ISOS‐D‐1 shelf protocol.     

Plastic Solar Cells: Interdiffusion of PCBM and P3HT Reveals Miscibility in a Photovoltaically Active Blend (Adv. Energy Mater. 1/2011)

Developing a better understanding of the evolution of morphology in plastic solar cells is the key to designing new materials and structures that achieve photoconversion efficiencies greater than 10%. In the most extensively characterized system, the poly(3‐hexyl thiophene) (P3HT):[6,6]‐phenyl‐C₆₁‐butyric‐acid‐methyl‐ester (PCBM) bulk heterojunction, the origins and evolution of the blend morphology during processes such as thermal annealing are not well understood. In this work, we use a model system, a bilayer of P3HT and PCBM, to develop a more complete understanding of the miscibility and diffusion of PCBM within P3HT during thermal annealing. We find that PCBM aggregates and/or molecular species are miscible and mobile in disordered P3HT, without disrupting the ordered lamellar stacking of P3HT chains. The fast diffusion of PCBM into the amorphous regions of P3HT suggests the favorability of mixing in this system, opposing the belief that phase‐pure domains form in BHJs due to immiscibility of these two components.     

Interdiffusion of PCBM and P3HT Reveals Miscibility in a Photovoltaically Active Blend

Developing a better understanding of the evolution of morphology in plastic solar cells is the key to designing new materials and structures that achieve photoconversion efficiencies greater than 10%. In the most extensively characterized system, the poly(3‐hexyl thiophene) (P3HT):[6,6]‐phenyl‐C₆₁‐butyric‐acid‐methyl‐ester (PCBM) bulk heterojunction, the origins and evolution of the blend morphology during processes such as thermal annealing are not well understood. In this work, we use a model system, a bilayer of P3HT and PCBM, to develop a more complete understanding of the miscibility and diffusion of PCBM within P3HT during thermal annealing. We find that PCBM aggregates and/or molecular species are miscible and mobile in disordered P3HT, without disrupting the ordered lamellar stacking of P3HT chains. The fast diffusion of PCBM into the amorphous regions of P3HT suggests the favorability of mixing in this system, opposing the belief that phase‐pure domains form in BHJs due to immiscibility of these two components.     

A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

Plasmonic Back Reflectors: A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

Doping‐Free Asymmetrical Silicon Heterocontact Achieved by Integrating Conjugated Molecules for High Efficient Solar Cell

Organic conjugated molecule/silicon (Si) heterojunction has been widely investigated to build up an asymmetrical heterocontact for efficient photovoltaics. However, it is still unclear how the organic molecular structures can affect their electronic coupling interaction with Si. Here, two widely explored electron acceptors of poly{[N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)} (N2200) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) are used to build up asymmetrical Si heterocontact to investigate their electronic coupling interaction. It is found that PCBM displays different electronic coupling with Si from N2200, which is ascribed to their various physical distance with Si based on a systematic and detailed density functional theory calculation. Organic layer incorporation not only suppresses the surface charge recombination velocity but also leads to an Ohmic contact between Si and Al. Therefore, a doping‐free organic/Si heterojunction photovoltaic with a power conversion efficiency of 14.9% is achieved with PCBM layer. This work discloses a key factor affecting organic/Si electronic coupling interaction, which helps build up high quality Si heterocontact for solar cells and other optoelectronic devices. Furthermore, the simplified heterocontact achieved by a low temperature, solution processed, and lithography‐free steps has a dramatic improvement on conventional diffusion doped‐silicon one at high temperature.     

Morphological Characterization of a Low‐Bandgap Crystalline Polymer:PCBM Bulk Heterojunction Solar Cells

Understanding the morphology of polymer‐based bulk heterojunction (BHJ) solar cells is necessary to improve device efficiencies. Blends of a low‐bandgap silole‐containing conjugated polymer, poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b;2′,3′‐d]silole)‐2,6‐diyl‐alt‐(4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole)‐5,5′‐diyl] (PSBTBT) with [6,6]phenyl‐C61‐butyric acid methyl ester (PCBM) were investigated under different processing conditions. The surface morphologies and vertical segregation of the “As‐Spun”, “Pre‐Annealed”, and “Post‐Annealed” films were studied by scanning force microscopy, contact angle measurements, X‐ray photoelectron spectroscopy, near‐edge X‐ray absorption fine structure spectroscopy, dynamic secondary ion mass spectrometry, and neutron reflectivity. The results showed that PSBTBT was enriched at the cathode interface in the “As‐Spun” films and thermal annealing increased the segregation of PSBTBT to the free surface, while thermal annealing after deposition of the cathode increased the PCBM concentration at the cathode interface. Grazing‐incidence X‐ray diffraction and small‐angle neutron scattering showed that the crystallization of PSBTBT and segregation of PCBM occurred during spin coating, and thermal annealing increased the ordering of PSBTBT and enhanced the segregation of the PCBM, forming domains ～10 nm in size, leading to an improvement in photovoltaic performance.     

The Role of Photon Energy in Free Charge Generation in Bulk Heterojunction Solar Cells

To determine the role of photon energy on charge generation in bulk heterojunction solar cells, the bias voltage dependence of photocurrent for excitation with photon energies below and above the optical band gap is investigated in two structurally related polymer solar cells. Charges generated in (poly[2,6‐(4,4‐bis(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′′]dithiophene)‐alt‐4,7‐(2,1,3‐benzothia­diazole)] (C‐PCPDTBT):[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) solar cells via excitation of the low‐energy charge transfer (CT) state, situated below the optical band gap, need more voltage to be extracted than charges generated with excitation above the optical band gap. This indicates a lower effective binding energy of the photogenerated electrons and holes when the excitation is above the optical band gap than when excitation is to the bottom of the CT state. In blends of PCBM with the silicon‐analogue, poly[(4,4‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (Si‐PCPDTBT), there is no effect of the photon energy on the electric field dependence of the dissociation efficiency of the CT state. C‐PCPDTBT and Si‐PCPDTBT have very similar electronic properties, but their blends with PCBM differ in the nanoscale phase separation. The morphology is coarser and more crystalline in Si‐PCPDTBT:PCBM blends. The results demonstrate that the nanomorphological properties of the bulk heterojunction are important for determining the effective binding energy in the generation of free charges at the heterojunction.     

Revealing Hidden UV Instabilities in Organic Solar Cells by Correlating Device and Material Stability

With state‐of‐the‐art organic solar cells (OSCs) surpassing 16% efficiency, stability becomes critical for commercialization. In this work, the power of using photoluminescence (PL) measurements on plain films is demonstrated, as well as high‐performance liquid chromatography analysis to reveal the origin of UV instabilities in OSCs based on the most commonly used acceptors PC₇₀BM ([6,6]‐phenyl‐C71‐butyric acid methyl ester), ITIC (3,9‐bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene), and o‐IDTBR (indacenodithiophene‐based non‐fullerene acceptor). The UV dependent stability tests reveal instabilities in solar cells based on PC₇₀BM and ITIC while devices based on o‐IDTBR are highly stable even under UV illumination. The analysis of solar cell devices based on charge extraction and sub‐bandgap external quantum efficiency only shows the UV‐dependent emergence of traps, while PL spectra of plain films on glass allows the disentanglement and identification of individual instabilities in multi‐component bulk‐heterojunction devices. In particular, the PL analysis demonstrates UV instabilities of PC₇₀BM and ITIC toward the processing additive 1,8 diiodooctane (DIO). The chemical analysis reveals the in‐depth mechanism, by providing direct proof of photochemical reactions of PC₇₀BM and ITIC with UV‐induced radicals of DIO. Based on this scientific understanding, it is shown how to stabilize PBQ‐QF:PC₇₀BM devices.