Review on Challenges and Recent Advances in the Electrochemical Performance of High Capacity Li‐ and Mn‐Rich Cathode Materials for Li‐Ion Batteries

Li and Mn‐rich layered oxides, xLi₂MnO₃·(1–x)LiMO₂ (M=Ni, Mn, Co), are promising cathode materials for Li‐ion batteries because of their high specific capacity that can exceed 250 mA h g^?1. However, these materials suffer from high 1^st cycle irreversible capacity, gradual capacity fading, low rate capability, a substantial charge‐discharge voltage hysteresis, and a large average discharge voltage decay during cycling. The latter detrimental phenomenon is ascribed to irreversible structural transformations upon cycling of these cathodes related to potentials ≥4.5 V required for their charging. Transition metal inactivation along with impedance increase and partial layered‐to‐spinel transformation during cycling are possible reasons for the detrimental voltage fade. Doping of Li, Mn‐rich materials by Na, Mg, Al, Fe, Co, Ru, etc. is useful for stabilizing capacity and mitigating the discharge‐voltage decay of xLi₂MnO₃·(1–x)LiMO₂ electrodes. Surface modifications by thin coatings of Al₂O₃, V₂O₅, AlF₃, AlPO₄, etc. or by gas treatment (for instance, by NH₃) can also enhance voltage and capacity stability during cycling. This paper describes the recent literature results and ongoing efforts from our groups to improve the performance of Li, Mn‐rich materials. Focus is also on preparation of cobalt‐free cathodes, which are integrated layered‐spinel materials with high reversible capacity and stable performance.     

High‐Voltage‐Driven Surface Structuring and Electrochemical Stabilization of Ni‐Rich Layered Cathode Materials for Li Rechargeable Batteries

Layered lithium–nickel–cobalt–manganese oxide (NCM) materials have emerged as promising alternative cathode materials owing to their high energy density and electrochemical stability. Although high reversible capacity has been achieved for Ni‐rich NCM materials when charged beyond 4.2 V versus Li⁺/Li, full lithium utilization is hindered by the pronounced structural degradation and electrolyte decomposition. Herein, the unexpected realization of sustained working voltage as well as improved electrochemical performance upon electrochemical cycling at a high operating voltage of 4.9 V in the Ni‐rich NCM LiNi_0.895Co_0.085Mn_0.02O₂ is presented. The improved electrochemical performance at a high working voltage at 4.9 V is attributed to the removal of the resistive Ni²⁺O rock‐salt surface layer, which stabilizes the voltage profile and improves retention of the energy density during electrochemical cycling. The manifestation of the layered Ni²⁺O rock‐salt phase along with the structural evolution related to the metal dissolution are probed using in situ X‐ray diffraction, neutron diffraction, transmission electron microscopy, and X‐ray absorption spectroscopy. The findings help unravel the structural complexities associated with high working voltages and offer insight for the design of advanced battery materials, enabling the realization of fully reversible lithium extraction in Ni‐rich NCM materials.     

In Situ Probing and Synthetic Control of Cationic Ordering in Ni‐Rich Layered Oxide Cathodes

Ni‐rich layered oxides (LiNi_1–x M_x O₂; M = Co, Mn, …) are appealing alternatives to conventional LiCoO₂ as cathodes in Li‐ion batteries for automobile and other large‐scale applications due to their high theoretical capacity and low cost. However, preparing stoichiometric LiNi_1–x M_x O₂ with ordered layer structure and high reversible capacity, has proven difficult due to cation mixing in octahedral sites. Herein, in situ studies of synthesis reactions and the associated structural ordering in preparing LiNiO₂ and the Co‐substituted variant, LiNi_0.8Co_0.2O₂, are made, to gain insights into synthetic control of the structure and electrochemical properties of Ni‐rich layered oxides. Results from this study indicate a direct transformation of the intermediate from the rock salt structure into hexagonal phase, and during the process, Co substitution facilities the nucleation of a Co‐rich layered phase at low temperatures and subsequent growth and stabilization of solid solution Li(Ni, Co)O₂ upon further heat treatment. Optimal conditions are identified from the in situ studies and utilized to obtain stoichiometric LiNi_0.8Co_0.2O₂ that exhibits high capacity (up to 200 mA h g^?1 ) with excellent retention. The findings shed light on designing high performance Ni‐rich layered oxide cathodes through synthetic control of the structural ordering in the materials.     

High‐Capacity Concentration Gradient Li[Ni0.865Co0.120Al0.015]O2 Cathode for Lithium‐Ion Batteries

A Ni‐rich concentration‐gradient Li[Ni_0.865Co_0.120Al_0.015]O₂ (NCA) cathode is prepared with a Ni‐rich core to maximize the discharge capacity and a Co‐rich particle surface to provide structural and chemical stability. Compared to the conventional NCA cathode with a uniform composition, the gradient NCA cathode exhibits improved capacity retention and better thermal stability. Even more remarkably, the gradient NCA cathode maintains 90% of its initial capacity after 100 cycles when cycled at 60 °C, whereas the conventional cathode exhibits poor capacity retention and suffers severe structural deterioration. The superior cycling stability of the gradient NCA cathode largely stemmed from the gradient structure combines with the Co‐rich surface, which provides chemical stability against electrolyte attack and reduces the inherent internal strain observed in all Ni‐rich layered cathodes in their charged state, thus providing structural stability against the repeated anisotropic volume changes during cycling. The high discharge capacity of the proposed gradient NCA cathode extends the driving range of electric vehicles and reduces battery costs. Furthermore, its excellent capacity retention guarantees a long battery life. Therefore, gradient NCA cathodes represent one of the best classes of cathode materials for electric vehicle applications that should satisfy the demands of future electric vehicles.     

Ni‐Rich/Co‐Poor Layered Cathode for Automotive Li‐Ion Batteries: Promises and Challenges

To pursue a higher energy density (>300 Wh kg^?1 at the cell level) and a lower cost (<$125 kWh^?1 expected at 2022) of Li‐ion batteries for making electric vehicles (EVs) long range and cost‐competitive with internal combustion engine vehicles, developing Ni‐rich/Co‐poor layered cathode (LiNi_1?x?yCo_xMn_yO₂, x+y ≤ 0.2) is currently one of the most promising strategies because high Ni content is beneficial to high capacity (>200 mAh g^?1) while low Co content is favorable to minimize battery cost. Unfortunately, Ni‐rich cathodes suffer from limited structure stability and electrode/electrolyte interface stability in the charged state, leading to electrode degradation and poor cycling performance. To address these problems, various strategies have been employed such as doping, structural optimization design (e.g., core–shell structure, concentration‐gradient structure, etc.), and surface coating. In this review, five key aspects of Ni‐rich/Co‐poor layered cathode materials are explored: energy density, fast charge capability, service life including cycling life and calendar life, cost and element resources, and safety. This enables a comprehensive analysis of current research advances and challenges from the perspective of both academy and industry to help facilitate practical applications for EVs in the future.     

Narrowing the Gap between Theoretical and Practical Capacities in Li‐Ion Layered Oxide Cathode Materials

Although layered lithium oxides have become the cathode of choice for state‐of‐the‐art Li‐ion batteries, substantial gaps remain between the practical and theoretical energy densities. With the aim of supporting efforts to close this gap, this work reviews the fundamental operating mechanisms and challenges of Li intercalation in layered oxides, contrasts how these challenges play out differently for different materials (with emphasis on Ni–Co–Al (NCA) and Ni–Mn–Co (NMC) alloys), and summarizes the extensive corpus of modifications and extensions to the layered lithium oxides. Particular emphasis is given to the fundamental mechanisms behind the operation and degradation of layered intercalation electrode materials as well as novel modifications and extensions, including Na‐ion and cation‐disordered materials.     

Countering Voltage Decay and Capacity Fading of Lithium‐Rich Cathode Material at 60 °C by Hybrid Surface Protection Layers

Li‐rich layered metal oxides have attracted much attention for their high energy density but still endure severe capacity fading and voltage decay during cycling, especially at elevated temperature. Here, facile surface treatment of Li_1.17Ni_0.17Co_0.17Mn_0.5O₂ (0.4Li₂MnO₃·0.6LiNi_1/3Co_1/3Mn_1/3O₂) spherical cathode material is designed to address these drawbacks by hybrid surface protection layers composed of Mg²⁺ pillar and Li‐Mg‐PO₄ layer. As a result, the surface coated Li‐rich cathode material exhibits much enhanced cycling stability at 60 °C, maintaining 72.6% capacity retention (180 mAh g^?1) between 3.0 and 4.7 V after 250 cycles. More importantly, 88.7% average discharge voltage retention can be obtained after the rigorous cycle test. The strategy developed here with novel hydrid surface protection effect can provide a vital approach to inhibit the undesired side reactions and structural deterioration of Li‐rich cathode materials and may also be useful for other layered oxides to increase their cycling stability at elevated temperature.     

Understanding the Rate Capability of High‐Energy‐Density Li‐Rich Layered Li1.2Ni0.15Co0.1Mn0.55O2 Cathode Materials

The high‐energy‐density, Li‐rich layered materials, i.e., xLiMO₂(1‐x)Li₂MnO₃, are promising candidate cathode materials for electric energy storage in plug‐in hybrid electric vehicles (PHEVs) and electric vehicles (EVs). The relatively low rate capability is one of the major problems that need to be resolved for these materials. To gain insight into the key factors that limit the rate capability, in situ X‐ray absorption spectroscopy (XAS) and X‐ray diffraction (XRD) studies of the cathode material, Li_1.2Ni_0.15Co_0.1Mn_0.55O₂ [0.5Li(Ni_0.375Co_0.25 Mn_0.375)O₂·0.5Li₂MnO₃], are carried out. The partial capacity contributed by different structural components and transition metal elements is elucidated and correlated with local structure changes. The characteristic reaction kinetics for each element are identified using a novel time‐resolved XAS technique. Direct experimental evidence is obtained showing that Mn sites have much poorer reaction kinetics both before and after the initial activation of Li₂MnO₃, compared to Ni and Co. These results indicate that Li₂MnO₃ may be the key component that limits the rate capability of Li‐rich layered materials and provide guidance for designing Li‐rich layered materials with the desired balance of energy density and rate capability for different applications.     

Unraveling the Voltage Decay Phenomenon in Li‐Rich Layered Oxide Cathode of No Oxygen Activity

Extensive efforts have been devoted to unraveling the true cause of voltage decay in Li, Mn‐rich layered oxides. An initial consensus was reached on structural rearrangement, then leaned toward the newly discovered lattice oxygen activity. It is challenging to differentiate their explicit roles because these events typically coexist during the electrochemical reaction of most Li‐rich layered oxides. Here, the voltage decay behavior is probed in Li_1.2Ni_0.2Ru_0.6O₂, a structurally and electrochemically relevant compound to Li, Mn‐rich layered oxide, but of no oxygen activity. Such intriguing characteristics allow the explicit decoupling of the contribution of transition metal migration and lattice oxygen activity to voltage decay in Li‐rich layered oxides. The results demonstrate that the microstructural evolution, mainly originating from transition metal migration, is a direct cause of voltage decay, and lattice oxygen activity likely accelerates the decay.     

Li[Ni0.9Co0.09W0.01]O2: A New Type of Layered Oxide Cathode with High Cycling Stability

Substituting W for Al in the Ni‐rich cathode Li[Ni_0.885Co_0.10Al_0.015]O₂ (NCA89) produces Li[Ni_0.9Co_0.09W_0.01]O₂ (NCW90) with markedly reduced primary particle size. Particle size refinement considerably improves the cathode's cycling stability such that the NCW90 cathode retains 92% of its initial capacity after 1000 cycles (compared to 63% for NCA89), while the cathode produces a high initial discharge capacity of 231.2 mAh g^?1 (at 0.1 C). Thus, the proposed NCW90 can deliver high energy density and a long battery lifetime simultaneously, unlike other Ni‐rich layered oxide cathodes. This unprecedented cycling stability is mainly attributed to a series of interparticular microfractures that absorb the anisotropic lattice strain caused by a deleterious phase transition near the charge end, thereby improving the cathode's resistance to fracture. Microcrack suppression preserves the mechanical integrity of the cathode particles during cycling and protects the particle interior from detrimental electrolyte attack. The proposed NCW90 cathode provides an improved material from which a new series of Ni‐rich layered cathode can be developed for next‐generation electric vehicles.     

A New Spinel‐Layered Li‐Rich Microsphere as a High‐Rate Cathode Material for Li‐Ion Batteries

Li‐rich layered materials are considered to be the promising low‐cost cathodes for lithium‐ion batteries but they suffer from poor rate capability despite of efforts toward surface coating or foreign dopings. Here, spinel‐layered Li‐rich Li‐Mn‐Co‐O microspheres are reported as a new high‐rate cathode material for Li‐ion batteries. The synthetic procedure is relatively simple, involving the formation of uniform carbonate precursor under solvothermal conditions and its subsequent transformation to an assembled microsphere that integrates a spinel‐like component with a layered component by a heat treatment. When calcined at 700 °C, the amount of transition metal Mn and Co in the Li‐Mn‐Co‐O microspheres maintained is similar to at 800 °C, while the structures of constituent particles partially transform from 2D to 3D channels. As a consequence, when tested as a cathode for lithium‐ion batteries, the spinel‐layered Li‐rich Li‐Mn‐Co‐O microspheres obtained at 700 °C show a maximum discharge capacity of 185.1 mA h g^?1 at a very high current density of 1200 mA g^?1 between 2.0 and 4.6 V. Such a capacity is among the highest reported to date at high charge‐discharge rates. Therefore, the present spinel‐layered Li‐rich Li‐Mn‐Co‐O microspheres represent an attractive alternative to high‐rate electrode materials for lithium‐ion batteries.     

New Insight into Ni‐Rich Layered Structure for Next‐Generation Li Rechargeable Batteries

An increase in the amount of nickel in LiMO₂ (M = Ni, Co, Mn) layered system is actively pursued in lithium‐ion batteries to achieve higher capacity. Nevertheless, fundamental effects of Ni element in the three‐component layered system are not systematically studied. Therefore, to unravel the role of Ni as a major contributor to the structural and electrochemical properties of Ni‐rich materials, Co‐fixed LiNi_0.5+xCo_0.2Mn_0.3–xO₂ (x = 0, 0.1, and 0.2) layered materials are investigated. The results, on the basis of synchrotron‐based characterization techniques, present a decreasing trend of Ni²⁺ content in Li layer with increasing total Ni contents. Moreover, it is discovered that the c_hex.‐lattice parameter of layered system is not in close connection with the interslab thickness related to actual Li ion pathway. The interslab thickness increases with increasing Ni concentration even though the c_hex.‐lattice parameter decreases. Furthermore, the lithium ion pathway is preserved in spite of the fact that the c‐axis is collapsed at highly deintercalated states. Also, a higher Ni content material shows better structural properties such as larger interslab thickness, lower cation disorder, and smoother phase transition, resulting in better electrochemical properties including higher Li diffusivity and lower overpotential when comparing materials with lower Ni content.     

Spinel‐Layered Core‐Shell Cathode Materials for Li‐Ion Batteries

In an attempt to overcome the problems associated with LiNiO₂, the solid solution series of lithium nickel‐metal oxides, Li[Ni_1–xM_x]O₂ (with M = Co, Mn, Al, Ti, Mg, etc.), have been investigated as favorable cathode materials for high‐energy and high‐power lithium‐ion batteries. However, along with the improvement in the electrochemical properties in Ni‐based cathode materials, the thermal stability has been a great concern, and thus violent reaction of the cathode with the electrolyte needs to be avoided. Here, we report a heterostructured Li[Ni_0.54Co_0.12Mn_0.34]O₂ cathode material which possesses both high energy and safety. The core of the particle is Li[Ni_0.54Co_0.12Mn_0.34]O₂ with a layered phase (R3‐m) and the shell, with a thickness of < 0.5 μm, is a highly stable Li_1+x[CoNi_xMn_2–x]₂O₄ spinel phase (Fd‐3m). The material demonstrates reversible capacity of 200 mAhg‐1 and retains 95% capacity retention under the most severe test condition of 60 °C. In addition, the amount of oxygen evolution from the lattice in the cathode with two heterostructures is reduced by 70%, compared to the reference sample. All these results suggest that the bulk Li[Ni_0.54Co_0.12Mn_0.34]O₂ consisting of two heterostructures satisfy the requirements for hybrid electric vehicles, power tools, and mobile electronics.     

High Voltage Operation of Ni‐Rich NMC Cathodes Enabled by Stable Electrode/Electrolyte Interphases

The lithium (Li) metal battery (LMB) is one of the most promising candidates for next‐generation energy storage systems. However, it is still a significant challenge to operate LMBs with high voltage cathodes under high rate conditions. In this work, an LMB using a nickel‐rich layered cathode of LiNi_0.76Mn_0.14Co_0.10O₂ (NMC76) and an optimized electrolyte [0.6 m lithium bis(trifluoromethanesulfonyl)imide + 0.4 m lithium bis(oxalato)borate + 0.05 m LiPF₆ dissolved in ethylene carbonate and ethyl methyl carbonate (4:6 by weight)] demonstrates excellent stability at a high charge cutoff voltage of 4.5 V. Remarkably, these Li||NMC76 cells can deliver a high discharge capacity of >220 mA h g^?1 (846 W h kg^?1) and retain more than 80% capacity after 1000 cycles at high charge/discharge current rates of 2C/2C (1C = 200 mA g^?1). This excellent electrochemical performance can be attributed to the greatly enhanced structural/interfacial stability of both the Ni‐rich NMC76 cathode material and the Li metal anode using the optimized electrolyte.     

Ni‐Rich Layered Cathode Materials with Electrochemo‐Mechanically Compliant Microstructures for All‐Solid‐State Li Batteries

While Ni‐rich cathode materials combined with highly conductive and mechanically sinterable sulfide solid electrolytes are imperative for practical all‐solid‐state Li batteries (ASLBs), they suffer from poor performance. Moreover, the prevailing wisdom regarding the use of Li[Ni,Co,Mn]O₂ in conventional liquid electrolyte cells, that is, increased capacity upon increased Ni content, at the expense of degraded cycling stability, has not been applied in ASLBs. In this work, the effect of overlooked but dominant electrochemo‐mechanical on the performance of Ni‐rich cathodes in ASLBs are elucidated by complementary analysis. While conventional Li[Ni_0.80Co_0.16Al_0.04]O₂ (NCA80) with randomly oriented grains is prone to severe particle disintegration even at the initial cycle, the radially oriented rod‐shaped grains in full‐concentration gradient Li[Ni_0.75Co_0.10Mn_0.15]O₂ (FCG75) accommodate volume changes, maintaining mechanical integrity. This accounts for their different performance in terms of reversible capacity (156 vs 196 mA h g^?1), initial Coulombic efficiency (71.2 vs 84.9%), and capacity retention (46.9 vs 79.1% after 200 cycles) at 30 °C. The superior interfacial stability for FCG75/Li₆PS₅Cl to for NCA80/Li₆PS₅Cl is also probed. Finally, the reversible operation of FCG75/Li ASLBs is demonstrated. The excellent performance of FCG75 ranks at the highest level in the ASLB field.     

Controlled Atomic Solubility in Mn‐Rich Composite Material to Achieve Superior Electrochemical Performance for Li‐Ion Batteries

The quest for high energy density and high power density electrode materials for lithium‐ion batteries has been intensified to meet strongly growing demand for powering electric vehicles. Conventional layered oxides such as Co‐rich LiCoO₂ and Ni‐rich Li(Ni_xMn_yCo_z)O₂ that rely on only transition metal redox reaction have been faced with growing constraints due to soaring price on cobalt. Therefore, Mn‐rich electrode materials excluding cobalt would be desirable with respect to available resources and low cost. Here, the strategy of achieving both high energy density and high power density in Mn‐rich electrode materials by controlling the solubility of atoms between phases in a composite is reported. The resulting Mn‐rich material that is composed of defective spinel phase and partially cation‐disordered layered phase can achieve the highest energy density, ≈1100 W h kg^?1 with superior power capability up to 10C rate (3 A g^?1) among other reported Mn‐rich materials. This approach provides new opportunities to design Mn‐rich electrode materials that can achieve high energy density and high power density for Li‐ion batteries.     

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Ni‐rich Li[Ni_xCo_yMn_1?x?y]O₂ (x ≥ 0.8) layered oxides are the most promising cathode materials for lithium‐ion batteries due to their high reversible capacity of over 200 mAh g^?1. Unfortunately, the anisotropic properties associated with the α‐NaFeO₂ structured crystal grains result in poor rate capability and insufficient cycle life. To address these issues, a micrometer‐sized Ni‐rich LiNi_0.8Co_0.1Mn_0.1O₂ secondary cathode material consisting of radially aligned single‐crystal primary particles is proposed and synthesized. Concomitant with this unique crystallographic texture, all the exposed surfaces are active {010} facets, and 3D Li⁺ ion diffusion channels penetrate straightforwardly from surface to center, remarkably improving the Li⁺ diffusion coefficient. Moreover, coordinated charge–discharge volume change upon cycling is achieved by the consistent crystal orientation, significantly alleviating the volume‐change‐induced intergrain stress. Accordingly, this material delivers superior reversible capacity (203.4 mAh g^?1 at 3.0–4.3 V) and rate capability (152.7 mAh g^?1 at a current density of 1000 mA g^?1). Further, this structure demonstrates excellent cycling stability without any degradation after 300 cycles. The anisotropic morphology modulation provides a simple, efficient, and scalable way to boost the performance and applicability of Ni‐rich layered oxide cathode materials.     

Understanding Performance Degradation in Cation‐Disordered Rock‐Salt Oxide Cathodes

The collective redox activities of transition‐metal (TM) cations and oxygen anions have been shown to increase charge storage capacity in both Li‐rich layered and cation‐disordered rock‐salt cathodes. Repeated cycling involving anionic redox is known to trigger TM migration and phase transformation in layered Li‐ and Mn‐rich (LMR) oxides, however, detailed mechanistic understanding on the recently discovered Li‐rich rock‐salt cathodes is largely missing. The present study systematically investigates the effect of oxygen redox on a Li_1.3Nb_0.3Mn_0.4O₂ cathode and demonstrates that performance deterioration is directly correlated to the extent of oxygen redox. It is shown that voltage fade and hysteresis begin only after initiating anionic redox at high voltages, which grows progressively with either deeper oxidation of oxygen at higher potential or extended cycling. In contrast to what is reported on layered LMR oxides, extensive TM reduction is observed but phase transition is not detected in the cycled oxide. A densification/degradation mechanism is proposed accordingly which elucidates how a unique combination of extensive chemical reduction of TM and reduced quality of the Li percolation network in cation‐disordered rock‐salts can lead to performance degradation in these newer cathodes with 3D Li migration pathways. Design strategies to achieve balanced capacity and stability are also discussed.     

Eliminating Transition Metal Migration and Anionic Redox to Understand Voltage Hysteresis of Lithium‐Rich Layered Oxides

Lithium‐rich layered oxides are promising candidate cathode materials for the Li‐ion batteries with energy densities above 300 Wh kg^?1. However, issues such as the voltage hysteresis and decay hinder their commercial applications. Due to the entanglement of the transition metal (TM) migration and the anionic redox upon lithium extraction at high potentials, it is difficult to recognize the origin of these issues in conventional Li‐rich layered oxides. Herein, Li₂MoO₃ is chosen since prototype material to uncover the reason for the voltage hysteresis as the TM migration and anionic redox can be eliminated below 3.6 V versus Li⁺/Li in this material. On the basis of comprehensive investigations by neutron powder diffraction, scanning transmission electron microscopy, synchrotron X‐ray absorption spectroscopy, and density functional theory calculations, it is clarified that the ordering–disordering transformation of the Mo₃O₁₃ clusters induced by the intralayer Mo migration is responsible for the voltage hysteresis in the first cycle; the hysteresis can take place even without the anionic redox or the interlayer Mo migration. A similar suggestion is drawn for its iso‐structured Li₂RuO₃ (C2/c). These findings are useful for understanding of the voltage hysteresis in other complicated Li‐rich layered oxides.     

Li–Ti Cation Mixing Enhanced Structural and Performance Stability of Li‐Rich Layered Oxide

Li‐rich layered metal oxides are one type of the most promising cathode materials in lithium‐ion batteries but suffer from severe voltage decay during cycling because of the continuous transition metal (TM) migration into the Li layers. A Li‐rich layered metal oxide Li_1.2Ti_0.26Ni_0.18Co_0.18Mn_0.18O₂ (LTR) is hereby designed, in which some of the Ti⁴⁺ cations are intrinsically present in the Li layers. The native Li–Ti cation mixing structure enhances the tolerance for structural distortion and inhibits the migration of the TM ions in the TMO₂ slabs during (de)lithiation. Consequently, LTR exhibits a remarkable cycling stability of 97% capacity retention after 182 cycles, and the average discharge potential drops only 90 mV in 100 cycles. In‐depth studies by electron energy loss spectroscopy and aberration‐corrected scanning transmission electron microscopy demonstrate the Li–Ti mixing structure. The charge compensation mechanism is uncovered with X‐ray absorption spectroscopy and explained with the density function theory calculations. These results show the superiority of introducing transition metal ions into the Li layers in reinforcing the structural stability of the Li‐rich layered metal oxides. These findings shed light on a possible path to the development of Li‐rich materials with better potential retention and a longer lifespan.